Atdec VFS-Q User manual

  • Hello! I've reviewed the user manual for the Visidec Freestanding Quad Mount VFS-Q. This document provides detailed instructions on how to assemble the mount, attach displays using VESA plates, and adjust for optimal viewing. It also covers cable management techniques. I'm ready to help answer any questions you have about setting up or using this product.
  • What is the maximum weight each Quickshift Donut can support?
    What VESA mounting hole configurations does this product support?
    What tools are required for installation?
Component Checklist
VFS-Q
IMPORTANT INFORMATION:
Step 1. Check Components
Step 2. Attach Upright Pole to Base
! IMPORTANT - Install Visidec Freestanding/Quad as per Installation Instructions.
! Each Quickshift Donut supports a maximum weight of 12kg (26.5lbs).
! This product supports VESA mounting hole configurations: 75x75mm and 100x100mm.
Display Mounting
Screws
Hardware
Check you have received all parts against the component checklist and Hardware above.
M4x12mm (x16)
VESA Plate (x4)
M4x10mm (x16)
M4x16mm (x16)
(Optional)
Security Screw (x4)
Cable Ball
(x8)
Cable Clip (x4)
5/3mm Allen
Key (x1 each)
Installation Instructions
Freestanding l Quad
Base
Upright Pole
TOOLS REQUIRED:
Phillips Head Screw Driver
M8x50mm
Screw (x1)
Step 3. Attach Horizontal Support
Cable Slot
USER
BACK
TIGHTEN
FIRMLY
Upright Pole
M8x50mm Screw
5mm Allen Key
Attach the Upright Pole to the Base as shown
below. Ensure the Cable Slot faces towards the rear.
! The manufacturer accepts no responsibility for incorrect installation.
Horizontal
Support (x2)
Clamp the Horizontal Support around the Upright Pole at the required height. Ensure the
Slots in all the Poles are facing to the rear. Tighten support using the M6x25mm Cap
Screw and 5mm Allen Key supplied.
M6x25mm
Cap Screw (x2)
Cable slot to
face back
CLAMP
HOLD SUPPORT IN PLACE
TIGHTEN
M6x25mm Cap Screw
5mm Allen Key
Cable
Clips
LOOSEN
TIGHTEN
Top of
Display
There are two mounting hole configurations:
• 75 x 75mm
• 100 x 100mm
from the Hardware supplied to suit
your Display.
Mounting Screws (x4)
VESA Plate
Step 4. Attach the VESA Plate to your Display
100mm
75mm
75mm
100mm
Back of Display
(Repeat steps 4 to 7 for each Display)
Installation Complete
C
No portion of this document or any artwork contained herein should be reproduced in anyway without the express written consent Atdec Pty Ltd.
Due to continuing product development, the manufacturer reserves the right to alter specifications without notice. Published 01.09.12
Step 5. Attach your Display to the Quickshift Donut
HOOK
Back of Display
Quickshift Mount.
Hook the top of the VESA plate onto the
Press and hold the Release Buttons. Gently
push bottom of VESA Plate into Quickshift
Mount. Release Buttons to lock in place.
Release Button Phillips-head Screwdriver
CLOSE
OPEN
Slide the Quickshift Donut to
desired position.
Close the lever to lock the
Quickshift Donut in place.
(Optional) Insert the Security Screw, and
tighten using a Phillips-head Screwdriver.
If necessary, adjust the tension
between the Donut and the Pole
using the 5mm Allen Key supplied.
TIGHTEN
PUSH
Step 7. Adjust the VESA Ball Mount
Security Screw
Open the lever to loosen the
Quickshift Donut.
SLIDE
TIGHTEN (+kg)
LOOSEN (-kg)
3mm Allen Key
Tension Plate
Step 6. Adjust the Position of the Quickshift Donut
Step 8. Cable Management
Connect cables to your Displays, routing them down the
rear of the poles. Push the cables into the slots, using
either the Cable Balls or Cable Clips to secure them to the
pole as shown.
Note: Ensure enough slack
is left in cables to allow for
movement. When the slot in
each pole cannot be used,
use the supplied Cable Clips
to secure the display cables.
Position your Display to the desired viewing angle using the ±20°
tilt allowed by the VESA Ball Mount. To make any adjustments,
use the 3mm Allen Key supplied. Apply half a turn at a time to
each screw on the Tension Plate to adjust evenly. If the display
does not hold its position, or is too resistant, adjust the Tension
Plate located at the rear of the VESA Ball Mount. Check the
display, and adjust again if necessary.
Cable
Balls
/