Motorola CP040 Service Information

Brand: Motorola

Model: CP040

Type: Service Information

Commercial Series

CP040 Radios

VHF1 (136-162MHz)

Service Information

Issue: October 2004

Computer Software Copyrights

The Motorola products described in this manual may include copyrighted Motorola computer programs stored

in semiconductor memories or other media. Laws in the United States and other countries preserve for

Motorola certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or

reproduce in any form, the copyrighted computer program. Accordingly, any copyrighted Motorola computer

programs contained in the Motorola products described in this manual may not be copied or reproduced in

any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola

products shall not be deemed to grant, either directly or by implication, estoppel or otherwise, any license

under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive royalty-

free license to use that arises by operation of law in the sale of a product.

iii

Table of Contents

Chapter 1 MODEL CHART AND TECHNICAL SPECIFICATIONS

1.0 CP040 Model Chart .............................................................................................1-1

2.0 Technical Specifications ......................................................................................1-2

Chapter 2 THEORY OF OPERATION

1.0 Introduction ..........................................................................................................2-1

2.0 VHF (136-162MHz) Receiver..............................................................................2-1

2.1 Receiver Front-End .......................................................................................2-2

2.2 Receiver Back-End.........................................................................................2-3

3.0 VHF (136-162MHz) Transmitter...........................................................................2-4

3.1 Transmitter Power Amplifier ...........................................................................2-4

3.2 Antenna Switch...............................................................................................2-4

3.3 Harmonic Filter ...............................................................................................2-5

3.4 Antenna Matching Network ............................................................................2-5

3.5 Power Control.................................................................................................2-5

4.0 VHF (136-162MHz) Frequency Generation Circuitry...........................................2-6

4.1 Fractional-N Synthesizer ................................................................................2-7

4.2 Voltage Controlled Oscillator (VCO) ...............................................................2-8

Chapter 3 TROUBLESHOOTING TABLES

1.0 Troubleshooting Table for Receiver.....................................................................3-1

2.0 Troubleshooting Table for Synthesizer ................................................................3-3

3.0 Troubleshooting Table for Transmitter ................................................................3-4

4.0 Troubleshooting Table for Board and IC Signals ................................................3-6

Chapter 4 UHF PCB/SCHEMATICS/PARTS LISTS

1.0 Allocation of Schematics and Circuit Boards .......................................................4-1

1.1 VHF (136-162MHz) ........................................................................................4-1

1.2 Six Layer Circuit Board...................................................................................4-1

1.3 Speaker and Microphone Schematic..............................................................4-2

2.0 VHF PCB 8486769Z02-A Schematic Diagrams ..................................................4-3

3.0 VHF PCB 8486769Z02-A Parts List...................................................................4-11

Chapter 1

MODEL CHART AND TECHNICAL SPECIFICATIONS

1.0 CP040 Model Chart

CP040 VHF1 136-162 MHz

Model Description

MDH50JDC9AA1_N CP040 136-162 MHz 5W 4-Ch

MDH50JDC9AA2_N CP040 136-162 MHz 5W 16-Ch

Item Description

X PMUD1981_ CP040 136-162 MHz 5W 4-Ch Tanapa

X PMUD1982_ CP040 136-162 MHz 5W 16-Ch Tanapa

PMLD4239_ CP040, Back Cover Kit 136-162 MHz 4-Ch

X PMLD4240_ CP040, Back Cover Kit 136-162 MHz 16-Ch

X PMLN4552_ Plain, Front Housing Kit, 4-Ch

X PMLN4553_ Plain, Front Housing Kit, 16-Ch

X NTN4497_R Li-Ion Battery, High Capacity

X WPLN4166 Rapid Desktop Charger (Base Only)

X EPNN7990_ Power Supply for Rapid Desktop Charger (UK)

X EPNN7991_ Power Supply for Rapid Desktop Charger (Euro)

X HLN8255 Belt Clip

X HAD9338_ Antenna, 136-162 MHz, Heliflex

6866549D01_ CP040 Basic User Guide

6864117B25_ Safety Leaflet

6866546D03_ RTTE Leaflet

X = Indicates one of each is required

1-2 MODEL CHART AND TECHNICAL SPECIFICATIONS

2.0 Technical Specifications

Data is specified for +25°C unless otherwise stated.

General VHF1

Frequency: 136-162 MHz

Channel Capacity: 4 or 16 Channels

Power Supply: 7.5 Volts ±20%

Dimensions:

with High Capacity Li-Ion Battery and

with Standard NiMH Battery:

with Slim Li-Ion Battery:

128.7mm H x 61.7mm W x 44.1mm D

128.7mm H x 61.7mm W x 41.3mm D

Weight:

with Slim Li-Ion Battery

with High Capacity Li-Ion Battery:

with Standard NiMH Battery:

365g

420g

480g

Average Battery Life @ (5-5-90 Duty Cycle):

with Slim Li-Ion Battery:

with High Capacity Li-Ion Battery:

with Standard NiMH Battery:

1 W

17Hrs.

19 Hrs.

13 Hrs.

5 W

12 Hrs.

14 Hrs

10 Hrs

Technical Specifications 1-3

*Availability subject to the laws and regulations of individual countries.

Transmitter

Specifications VHF1

RF Output

NiMH @ 7.5V:

Low

1 W

High

Frequency: 136-162 MHz

Channel Spacing: 12.5/20/25 kHz

Freq. Stability:

(-30°C to +60°C)

0.00025%

Spurs/Harmonics: -36 dBm < 1 GHz

-30 dBm > 1 GHz

Audio Response:

(from 6 dB/oct. Pre-emphasis, 300 to 3000Hz)

+1, -3 dB

Audio Distortion:@ 1000 Hz, 60% Rated Max. Dev. <3%

FM Noise: -40 dB (12.5 kHz)

-45 dB (25 kHz)

Receiver

Specifications

VHF1

12.5 kHz

VHF1

20/25kHz

Frequency: 136-162 MHz

Sensitivity 12dB EIA SINAD: 0.25 µV (typical)

Adjacent Channel Selectivity: -65 dB -70 dB

Intermodulation: -70 dB

Freq. Stability (-30°C to +60°C): 0.00025%

Spur Rejection: -75 dB

Image and 1/2 I-F Rejection: -70 dB

Audio Output @ <5% Distortion: 500 mW

Self Quieter Frequencies

VHF1

151.200

1-4 MODEL CHART AND TECHNICAL SPECIFICATIONS

Chapter 2

THEORY OF OPERATION

1.0 Introduction

This Chapter provides a detailed theory of operation for the VHF circuits in the radio. Schematic

diagrams and board layout diagrams are included in Chapter 4 in this Section of the manual.

2.0 VHF (136-162MHz) Receiver

The VHF receiver covers the range of 136-162 MHz and provides switchable IF bandwidth for use

with 20/25/30 kHz or 12.5 kHz channel spacing systems. The receiver is divided into two major

blocks, as shown in Figure 2-1.

■ Front End

■ Back End

Figure 2-1 VHF Receiver Block Diagram

Demodulator

Crystal

Filter

1st Mixer

Amp

Preselector

Filter

Interstage

Filter

Recovered Audio

RSSI

RX from

Antenna Switch

Inj Filter

First LO

from Synthesizer

Ceramic

Resonator

Cer Fltr

Switching

BW_SEL

12.5kHzFilter

2-2 THEORY OF OPERATION

2.1 Receiver Front End

Incoming RF signals from the antenna are first routed through the harmonic filter and antenna

switch, part of the transmitter circuitry, before being applied to the receiver front end. The receiver

front end consists of a preselector filter, RF amplifier, an interstage filter, and a double-balanced first

mixer.

The preselector filter is a fixed-tuned 4-pole design using discrete elements (L1-L4 and C1-C9) in a

series/shunt resonator configuration. It has a 3 dB bandwidth of 44 MHz, an insertion loss of 2 dB

and image attenuation of 37 dB at 226 MHz, with increasing attenuation at higher frequencies.

Diode CR1 protects the RF amplifier by limiting excessive RF levels.

The output of the filter is matched to the base of RF amplifier Q21, which provides 16 dB of gain and

a noise figure of 2 dB. Operating voltage is obtained from the 5R source, which is turned off during

transmit to reduce dissipation in Q21. Current mirror Q22 maintains the operating current of Q21

constant at 6.7 mA regardless of device and temperature variations, for optimum dynamic range

and noise figure.

The output of the RF amplifier is applied to the interstage filter, a fixed-tuned 3-pole series-coupled

resonator design having a 3 dB bandwidth of 54 MHz and insertion loss of 1.8 dB. This filter has an

image rejection of 40 dB at 226 MHz, with increasing attenuation at higher frequencies.

The output of the interstage filter is connected to the passive double-balanced mixer consisting of

components T41, T42, and CR41. This mixer has a conversion loss of 7 dB. High-side injection from

the frequency synthesizer is filtered by L40-L41 and C40-C44 to remove second harmonic energy

that may degrade half-IF spurious rejection performance. The injection filter has a 3 dB bandwidth

of 52 MHz and an insertion loss of 1.5 dB. The filtered injection signal is applied to T42 at a level of

+6 dBm.

The mixer output is applied to a diplexer network (L51-L52, C51, R51) which matches the 44.85

MHz IF signal to crystal filter FL51, and terminates the mixer into 50Ω at all other frequencies.

VHF (136-162MHz) Receiver 2-3

2.2 Receiver Back End

The receiver back end is a dual conversion design. High IF selectivity is provided by FL51, a 4-pole

fundamental mode 44.85 MHz crystal filter with a minimum 3 dB bandwidth of + 6.7 kHz, a

maximum 20 dB bandwidth of ±12.5 kHz, and a maximum insertion loss of 3.5 dB. The output is

matched to IF amplifier stage Q51 by L53 and C93. Q51 provides 16 dB of gain and a noise figure of

1.8 dB. The dc operating current is 1 mA. The output of Q51 is applied to the input of the receiver

IFIC U51. Diode CR51 limits the maximum RF level applied to the IFIC.

The IFIC is a low-voltage monolithic FM IF system incorporating a mixer/oscillator, two limiting IF

amplifiers, quadrature detector, logarithmic received signal strength indicator (RSSI), voltage

regulator and audio and RSSI op amps. The second LO frequency, 44.395 MHz, is determined by

Y51. The second mixer converts the 44.85 MHz high IF frequency to 455 kHz.

Additional IF selectivity is provided by two ceramic filters, FL52 (between the second mixer and IF

amp) and FL53 or FL54 (between the IF amp and the limiter input). The wider filter FL53 is used for

20/25 kHz channel spacing, and the narrower filter FL54 is used for 12.5 kHz channels. When the

BW_SEL line is high, the two upper diodes in packages D51 and D52 are forward biased, selecting

FL53 for 20/25 kHz channels. When the BW_SEL line is low, the two lower diodes in packages D51

and D52 are forward biased, selecting FL54 for 12.5 kHz channels.

Ceramic resonator Y70 provides phase vs. frequency characteristic required by the quadrature

detector, with 90 degree phase shift occurring at 455 kHz. Buffer Q70 provides a lower driving

impedance from the limiter to the resonator, improving the IF waveform and lowering the distortion

of the recovered audio signal. The recovered audio level at the DEMOD output is 100 mV rms (25

kHz channel, 3 kHz deviation) or 50 mV rms (12.5 kHz channel, 1.5 kHz deviation). An additional

RSSI output provides a DC voltage level that is proportional to RF signal level. This voltage is

measured by an A/D converter contained in the microprocessor (PE4_AN4, U401 pin 63).

FL52 FL53 FL54

Number of Elements: 4 6 6

Insertion Loss: 4 dB 4 dB 4 dB

6 dB Bandwidth: 15 kHz 15 kHz 9 kHz

50 dB Bandwidth: 30 kHz 30 kHz 22 kHz

Stopband Rejection: 27 dB 47 dB 47 dB

2-4 THEORY OF OPERATION

3.0 VHF Transmitter

The VHF transmitter covers the range of 136-162 MHz. Depending on model, the output power of

the transmitter is either switchable on a per-channel basis between high power (5 watts) and low

power (1 watt), or is factory preset to 2 watts. The transmitter is divided into four major blocks as

shown in Figure 2-2.

■ Power Amplifier

■ Harmonic Filter

■ Antenna Matching Network

■ Power Control.

Figure 2-2 VHF Transmitter Block Diagram

3.1 Transmitter Power Amplifier

The transmitter power amplifier has three stages of amplification. The first stage, Q100, operates in

Class AB from the 5T source. It provides 13 dB of gain and an output of 20 mW. The current drain is

typically 25mA. Components C105-C107 and L103 match the output of Q100 to the 50Ω input of the

module U110.

U110 is a two stage Silicon MOS FET power amplifier module. Drain voltage is obtained from

UNSW B+ after being routed through current-sense resistor R150 in the power control circuit. The

output power of the module is controlled by varying the DC gate bias on U110 pin 2 (VGG).

3.2 Antenna Switch

The antenna switch consists of two pin diodes, D120 and D121. In the receive mode, both diodes

are off. Signals applied at the antenna or at jack J140 are routed, via the harmonic filter, through

network C122-C124 and L121, to the receiver input. In the transmit mode, Q170 is on and TXB+ is

present, forward-biasing both diodes into conduction. The diode current is 50 mA, set by R120-

R122. The transmitter RF from U110 is routed through D120, and via the harmonic filter to the

antenna jack. D121 conducts, shunting RF power and preventing it from reaching the receiver. L121

is selected to appear as a 1/4 wave at VHF, so that the low impedance of D121 appears as a high

impedance at the junction of D120 and the harmonic filter input. This provides a high series

impedance and low shunt impedance divider between the power amplifier output and receiver input.

Power Control

Harmonic Filter

Antenna

Matching

Network

Power Amplifier Module U110

Q100

TX_INJ

(From VCO)

VDD

VGG

TX_ENA

PWR_SET

USWB+

RX_IN

(To Receiver)

Antenna

Switch

J140 Antenna

Jack

Antenna

VHF Transmitter 2-5

3.3 Harmonic Filter

The harmonic filter consists of components C130-C136 and L130-L132. The harmonic filter is a

seven-pole elliptical low-pass configuration, optimized for low insertion loss, with a 3 dB frequency

of approximately 180 MHz and typically less than 0.8 dB insertion loss in the passband.

3.4 Antenna Matching Network

The harmonic filter presents a 50Ω impedance to antenna jack J140. A matching network, made up

of C140-C141 and L140, is used to match the antenna impedance to the harmonic filter. This

optimizes the performance of the transmitter and receiver into the impedance presented by the

antenna, significantly improving the antenna's efficiency.

3.5 Power Control

The power control circuit is a dc-coupled amplifier whose output is the dc gate bias voltage (VGG)

applied to the two stages of the RF power amplifier U110.

The output power of the transmitter is adjusted by varying the setting of the power-set DAC

contained in the ASFICcmp IC (DACG, U451 pin 6). This PWR_SET voltage is applied to

U150 pin 3.

Stage U150-2 compares the voltage drop across current sense resistor R150 to the voltage drop

across resistor R151 caused by current flow through Q150, and adjusts its output (pin 7) to maintain

equal voltages at pins 5 and 6. Thus the current flow through Q150, and hence its emitter voltage, is

proportional to the current drawn by stage U110, which is in turn proportional to the transmitter

output power. The emitter voltage of Q150 is applied to U150 pin 2, where it is compared to the

power set voltage PWR_SET at pin 3.

The output of U150 pin 1 is divided by R110 and R111 and applied as a gate voltage to the power

amplifier U110. By varying this gate voltage as needed to keep the voltages at U150 pins 2 and 3

equal, power is maintained at the desired setting. Excessive final current, for example due to

antenna mismatch, causes a lowering of the voltage at U150 pin 6, an increased voltage at pin 2,

and a lowering of the voltage at pin 1 and of the gate voltage VGG. This prevents damage to the final

stage due to excessive current.

2-6 THEORY OF OPERATION

4.0 VHF Frequency Generation Circuitry

The frequency generation system, shown in Figure 2-3, is composed of two circuit blocks, the

Fractional-N synthesizer IC U201, the VCO/Buffer IC U251, and associated circuitry. Figure 2-4

shows the peripheral interconnect and support circuitry used in the synthesizer block, and

Figure 2-5 details the internal circuitry of the VCOBIC and its interconnections to the surrounding

components. Refer to the schematic to identify reference designators.

The Fractional-N synthesizer is powered by regulated 5V and 3V provided by U310 and U330

respectively. 5V is applied to U201 pins 13 and 30, and 3V is applied to pins 5, 20, 34 and 36. The

synthesizer in turn generates a super-filtered 4.5V supply (VSF, from pin 28) to power U251. In

addition to the VCO, the synthesizer also interfaces with the logic and ASFICcmp circuits.

Programming for the synthesizer is accomplished through the microprocessor SPI_DATA_OUT,

SPI_CLK, and SYNTH_CS (chip select) lines (U409 pins 100, 1 and 47 respectively). A logic high

(3V) from U201 pin 4 indicates to the microprocessor that the synthesizer is locked.

Figure 2-3 VHF Frequency Generation Unit Block Diagram

Transmit modulation from the ASFICcmp (U451 pin 40) is applied to U201 pin 10 (MOD_IN). An

electronic attenuator in the ASFICcmp adjusts overall transmitter deviation by varying the audio

level applied to the synthesizer IC. Internally the audio is digitized by the Fractional-N synthesizer

and applied to the loop divider to provide the low-port modulation. The audio is also routed through

an internal attenuator for the purpose of balancing the low port and high port modulation and

reducing the deviation by 6 dB for 12.5 kHz channels, and is available at U201 pin 41 (VCO_MOD).

This audio signal is routed to the VCO's modulator.

Synthesizer

U201

VCOBIC

U251

Voltage

Multiplier

Loop

Filter

To Mixer

To PA Driver

VCP

Vmult1

Vmult2

Aux3

MOD Out

Modulating

Signal

Rx VCO

Circuit

Tx VCO

Circuit

TRB

16.8 MHz

Ref. Osc.

Rx Out

Tx Out

Buffer

Q280

VHF Frequency Generation Circuitry 2-7

4.1 Fractional-N Synthesizer

The Fractional-N synthesizer, shown in Figure 2-4, uses a 16.8 MHz crystal (Y201) to provide the

reference frequency for the system. External components C201-C203, R202 and D201 are also part

of the temperature-compensated oscillator circuit. The dc voltage applied to varactor D201 from

U201 pin 25 is determined by a temperature-compensation algorithm within U201, and is specific to

each crystal Y201, based on a unique code assigned to the crystal that identifies its temperature

characteristics. Stability is better than 2.5 ppm over temperatures of -30 to 60 °C. Software-

programmable electronic frequency adjustment is achieved by an internal DAC which provides a

frequency adjustment voltage from U201 pin 25 to varactor D201.

The synthesizer IC U201 further divides the 16.8 MHz signal to 2.1 MHz, 2.225 MHz, or 2.4 MHz for

use as reference frequencies. It also provides a buffered 16.8 MHz signal at U201 pin 19 for use by

the ASFICcmp.

To achieve fast locking of the synthesizer, an internal adapt charge pump provides higher current at

U201 pin 45 to quickly force the synthesizer within lock range. The required frequency is then locked

by the normal mode charge pump at pin 43. A loop filter (C243-C245 and R243-R245) removes

noise and spurs from the steering voltage applied to the VCO varactors, with additional filtering

located in the VCO circuit.

Both the normal and adapt charge pumps get their supply from the capacitive voltage multiplier

made up of C221-C224 and D220-D221. Two 3V square waves from U201 pins 14-15 provide the

drive signals for the voltage multiplier, which generates 12.1V at U201 pin 47. This voltage is filtered

by C225-C228.

One of the auxiliary outputs of the synthesizer IC (AUX3, U201 pin 2) provides the TRB signal which

determines the operating mode of the VCO, either receive or transmit.

Figure 2-4 VHF Synthesizer Block Diagram

DATA

CLK

CEX

MODIN

, 5V

XTAL1

WARP

PREIN

VCP

Reference

Oscillator

Voltage

Multiplier

Voltage

Controlled

Oscillator

2-Pole

Loop Filter

DATA (U401 Pin 100)

CLOCK (U401 Pin 1)

SYNTH_CS (U401 Pin 47)

MOD IN (U451 Pin 40)

+5V (U310 Pin 5)

13,30

VMULT2

VMULT1

BIAS1

SFOUT

AUX3

IADAPT

IOUT

GND

FREFOUT

LOCK

6,22,23,24

Filtered 5V

Steering

Line

LOCK (U401 Pin 56)

Prescaler In

LO RF

Injection

TX RF

Injection

(First Stage of PA)

FREF (U451 Pin 34)

BIAS2

+3V (U330 Pin 5)

, 3V

MODOUT

U201

Low Voltage

Fractional-N

Synthesizer

5,20,34,36

TRB

VCO

Mod

2-8 THEORY OF OPERATION

4.2 Voltage Controlled Oscillator (VCO)

The VCOBIC (U251), shown in Figure 2-5, in conjunction with the Fractional-N synthesizer (U201)

generates RF in both the receive and the transmit modes of operation. The TRB line (U251 pin 19)

determines which oscillator and buffer are enabled. A sample of the RF signal from the enabled

oscillator is routed from U251 pin 12 through a low pass filter, to the prescaler input of the

synthesizer IC (U201 pin 32). After frequency comparison in the synthesizer, a resultant DC control

voltage is used to steer the VCO frequency. When the PLL is locked on frequency, this voltage can

vary between 3.0V and 9V. L251 and C252 further attenuate noise and spurs on the steering line

voltage.

In the receive mode, the TRB line (U251 pin 19) is low. This activates the receive VCO and the

receive buffer of U251, which operate within the range of 190.85 to 218.85 MHz. The VCO

frequency is determined by tank inductor L254, C253-C257, and varactor D251. The buffered RF

signal at U251 pin 8 is further amplified by Q280 and applied as RX_INJ to the low-pass injection

filter in the receiver front end circuit.

In the transmit mode, U251-19 is driven high by U201 pin 2, enabling the transmit VCO and buffer.

The 136-162 MHz RF signal from U251 pin 10 is applied as TX_INJ to the input of the transmitter

circuit via matching network C290-C291 and L291. TX VCO frequency is determined by L264,

C263-C267, and varactor D262. High-port audio modulation from the synthesizer IC is applied as

VCO_MOD to varactor D261 which modulates the transmit VCO.

Figure 2-5 VHF VCO Block Diagram

Presc

Matching

Network

Pin 8

Pin 14

Pin 10

3V (U330 Pin 5)

VCC Buffers

U201 Pin 32

AUX3 (U201 Pin 2)

Prescaler Out

Pin 12

Pin 19

Pin 20

TX/RX/BS

Switching Network

U251

VCOBIC

Rx Active

Bias

Tx Active

Bias

Pin 2

Rx-I adjust

Pin 1

Tx-I adjust

Pins 9,11,17

Pin 18

Vsens

Circuit

Pin 15

Pin 16

TX VCO

Circuit

Tank

RX VCO

Circuit

Tank

Pin 7

Vcc-Superfilter

Collector/RF in

Pin 4

Pin 5

Pin 6

V_SF (U201 Pin 28)

Vcc-Logic

(U330 Pin 5)

Steer Line

Voltage

(V_STEER)

Pin 13

Pin 3

TRB_IN

Buffer

Q280

RX INJ

V_SF

(U201 Pin 28)

TX INJ

Chapter 3

TROUBLESHOOTING TABLES

This section contains detailed troubleshooting tables. These tables should be used as a guide in

determining the problem areas. They are not a substitute for knowledge of circuit operation and

astute troubleshooting techniques. It is advisable to refer to the related detailed circuit descriptions

in the theory of operation sections prior to troubleshooting a radio.

Most troubleshooting tables end up by pointing to an IC to replace. It is not always noted, but it is

good practice to verify supplies and grounds to the affected IC and to trace continuity to the

malfunctioning signal and related circuitry before replacing any IC. For instance, if a clock signal is

not available at a destination, continuity from the source IC should be checked before replacing the

source IC.

1.0 Troubleshooting Table for Receiver

Symptom Possible Causes Procedure Corrective Action

Radio Dead (no

turn-on beep, no

LED indication)

1. Battery dead or

defective.

Substitute known good battery or

battery eliminator.

Charge or replace battery.

2. Defective battery

contacts.

Inspect battery contacts for corrosion

or bent terminals.

Clean/repair/replace J301.

3. Blown fuse Check voltage on each side of fuse.

If blown, 0 VDC after fuse.

Check for short on output,

check D301, VR301, trouble-

shoot/repair as needed, replace

fuse.

4. DC switching fault Verify battery voltage present at

S444 pin 5 when radio is on.

Verify Q494-1 is at least 1V dc,

Q494-6 is ~0.1V dc, Q493-3 is at

Vbatt.

Check/replace on-off-volume

control S444.

Troubleshoot/replace Q493/4.

5. Microprocessor not

starting up.

Verify clock input to U401-90

(EXTAL) is 7.3975 MHz using high

impedance probe. If clock is 3.8MHz,

check for shorts on U401 pins.

Connect RIB to verify

communication via CPS.

Verify U401-94 (RESET) is high.

Verify 16.8 MHz signal at U451-

34. If OK, troubleshoot/replace

U451. If not present, trouble-

shoot U201 Synthesizer.

Reprogram/reflash as needed.

If RESET is Low, troubleshoot

regulator U320. Check for

shorts at U401 pins. Replace

U401 (depot only). Reprogram/

reflash as needed.

6. Regulator fault Verify U310-5 is 5V dc, U320-5 is

3.3V dc, U330-5 is 3V dc.

Check for shorts on outputs,

troubleshoot/repair as needed,

replace faulty regulator.

3-2 TROUBLESHOOTING TABLES

No Audio 1. Synthesizer out of lock Verify U201-4 is at 3V dc. Troubleshoot synthesizer/VCO

circuits.

2. Defective IFIC Verify audio is present at U51-8. Check Q70, Y70, U51.

3. RX audio buffer fault Verify audio is present at U451-2. Check U510 and associated

parts.

4. ASFIC fault Verify audio is present at U451-41.

Verify U451-14 is high.

Check squelch setting, PL/DPL

programming. Troubleshoot/

replace U451.

5. Audio PA fault Verify U490-1 is <0.2V dc.

Verify audio is present at U490-5

and 8.

Check Q490.

Check/replace U490.

6. Defective speaker Verify audio is present at speaker

terminals.

If not, check continuity of J471-2

and 3. Check J491. If yes,

replace speaker.

No Receive

(squelch noise

present)

1. No first injection Check that RF level at T42-6 is

approx +6 dBm.

Check that RF level at U251-8 is at

least -8 dBm.

Check injection filter C40-44,

L40-41.

If yes, check Q280 and associ-

ated parts. If no, check U251

and components on pins 5 and

2. No 5R source. Verify U401-49 is high in RX.

Verify Q311 gate is 0V dc in RX

Verify Q311 drain is 5V dc in RX.

Check/replace U401

Check/replace Q313.

Check for shorts, check/replace

Q311.

3. Harmonic filter or

antenna switch fault

Apply on-channel 100 mV RF signal

at antenna port. Verify RF level at jct.

C1/C2 per schematic.

Check TX harmonic filter, D120-

121. Should be 0V dc on D120-

121.

4. Back end fault Apply on-channel 100 mV RF signal

at antenna port. Measure RF levels

from FL51 through U51.

Check components prior to

loss-of-signal point.

5. No second injection Measure RF level at U51-3, verify

approx. 280 mV rms.

If dc voltages at U51-3 and 4

are OK, check Y51 and

associated parts. If not replace

U51.

Symptom Possible Causes Procedure Corrective Action

Troubleshooting Table for Synthesizer 3-3

2.0 Troubleshooting Table for Synthesizer

Symptom Possible Causes Procedure Corrective Action

Synthesizer Out of

Lock (RX mode

only)

1. VCO fault Verify oscillator is working, check RF

level at U251-10 per schematic.

Check dc voltages at U251 pin 2

through 6 and 10 per

Board and IC

troubleshooting table

Verify steering line voltage is

between ~3V and 10V.

Check VCO tank components

connected to U251-5 and 6.

Check for shorts/opens, replace

U251.

Check D251 and associated

components.

2. Synthesizer fault Verify TRB line (from U201-2 to

U251-19) is low in RX mode

Check for shorts, check U201

voltages per

Board and IC

troubleshooting table

, replace

U201 if incorrect.

3. Programming fault Verify RX channel programming is

correct.

Re-program if necessary.

Synthesizer Out of

Lock (TX mode

only)

1. VCO fault Verify oscillator is working, check RF

level at U251-10 per schematic.

Check dc voltages at U251 pins

1,3,4,10,15,16 per

Board and IC

troubleshooting table

Verify steering line voltage is

between ~3V and 10V.

Check VCO tank components

connected to U251-15 and 16.

Check for shorts/opens, replace

U251.

Check D261 and associated

components.

2. Synthesizer fault Verify TRB line (U201-2 to U251-19)

is high (3V) in TX mode

Check for shorts, check U201

voltages per

Board and IC

troubleshooting table

, replace

U201 if incorrect.

3. Programming fault Verify TX channel programming is

correct.

Re-program if necessary.

Synthesizer Out of

Lock (RX and TX

modes)

1. VCO fault Check that RF level at U251-12 is at

least 150 mV (VHF)

If low/missing, check L276,

C276-7, R276.

2. Synthesizer fault Check that RF level at U201-32 is at

least 150 mV (VHF).

Verify steering line voltage is

between ~3V and 10V.

If correct, check/replace U201.

If incorrect, check R248 and

C241.

Check loop filter components

R243-5 and C243-5.

3. DC voltage fault Verify 4.5V dc at U201-28.

Verify 12.1V dc at U201-47

Check C231-233, etc., for

shorts. If OK check/replace

U201.

Check for 3V 1.05 MHz sq

waves at U201-14 and 15.

Check C218-228, D220-221.

4. Programming fault Verify channel programming is cor-

rect.

Re-program if necessary.

3-4 TROUBLESHOOTING TABLES

3.0 Troubleshooting Table for Transmitter

Symptom Possible Causes Procedure Corrective Action

No Transmit (no

TX LED indication)

1. PTT switch defective. Verify U401-71 goes low when PTT

is pressed.

Replace PTT switch S441.

2. EXT MIC PTT fault Verify U401-72 goes low when J471-

4 is grounded.

Check/replace Q470, L471 etc.

No Transmit (TX

LED indication OK)

1. Synthesizer out of lock Refer to Synthesiser trouble-

shooting table

Refer to Synthesiser trouble-

shooting table

2. No TX_ENABLE Verify U401-50 is high when pin 71

or 72 is low.

Check/replace U401.

3. TX DC switch fault Verify Q171-C is 0V in TX.

Verify Q170-C is at Vbatt in TX.

Replace Q171.

Check for shorts, replace Q170.

4. Power control fault Check Q150 and U150 dc voltages

per schematic and

Synthesiser

troubleshooting table

Repair/replace defective com-

ponents

5. No TX injection Check that RF level at jct. R100/

R101 per schematic.

Check U251, L291-292, C290-

291.

6. No 5T source Verify Q312 gate is 0V dc in TX

Verify Q312 drain is 5V dc in TX.

Check/replace Q313.

Check for shorts, check/replace

Q312.

7. TX gain stage failure Check RF levels at Q100 and U110

per schematic.

Troubleshoot Q100/U110 and

associated circuitry.

8. Antenna switch failure Verify dc voltage at jct. R122/L120 is

approx 1.5V.

Check/replace D120-121, L120-

121, R120-122, etc.

Low Power 1. Low TX injection Check that RF level at jct. R100/

R101 per schematic.

Check U251, L291-292, C290-

291.

2. Low gain in TX stage Verify dc voltage at Q100-E is ~1.3V

(VHF).

Verify that RF level at U110-1 is

approx. 1V (VHF).

Verify 5T voltage is correct.

Troubleshoot Q100 circuitry.

Check/replace Q100.

3. Incorrect control volt-

age

Verify that the dc voltage at

PWR_SET (R162) is approx 1.8V dc

(at 1 watt) to 2.6V dc (at 4-5 watts).

Verify that the dc voltage at U110-2

is approx 2-3V dc (at 1 watt) to 3-4V

dc (at 4-5 watts). (See schematic.)

Check programming. Trouble-

shoot controller circuitry. Check/

replace U451.

Troubleshoot U150, Q150 and

associated circuitry.

4. Antenna switch defect Verify dc voltage at jct. R122/L120

(VHF) is approx 1.7V.

Note: Do not

attempt to measure RF or DC

voltages at the diodes. Damage to

test equipment may occur.

Check/replace D120-121, L120-

121, R120-122, etc.

5. Harmonic filter defect Visually inspect components C130-

137, L130-132. Check dc continuity

of L130-132

in RX mode only

Repair/replace if necessary.

Page is loading ...

Motorola CP040 Service Information

Motorola CP040 Service Information

Motorola CP040 Service Information

Related papers

Other documents