Sea-doo Aqua Master ZS40 User manual

Brand: Sea-doo

Model: Aqua Master ZS40

Type: User manual

This manual is also suitable for

Aqua Master SD75004

English Version

CAUTION

ELECTRICALLY OPERATED PRODUCT

Not recommended for children under 14 years of age. As with all

electrical products, precautions should be observed during handling

and used to reduce the risk of electric shock.

User Manual

SDP95123

Distributors in the United States and Canada provide a standard Limited

Warranty for 6 months from the date of purchase for new products. If

you're not located in the United States or Canada, please contact your

local distributor for warranty arrangements in your territory.

Please visit

www.seadooseascooter.com for distributor

/ Service Centre details.

Distributors ONLY warrant Stallion products purchased from an

authorized dealer.

Ask your local Distributor for the warranty period in your region by calling their

Service Center. Any part of the product supplied by the Distributor and found in the

reasonable judgment of the Distributor to be defective in material or workmanship

will be repaired or replaced by the Distributor without charge for parts or labor. The

product including any defective part must be sent to the Distributor within the

warranty period. The customer will pay for the expense of delivering the product to

the Distributor. The Distributor will pay for the expense of returning the product to

the customer.

ALWAYS ACTIVATE YOUR WARRANTY IMMEDIATELY ON

http://www.seadooseascooter.com/warranty.html

www.seadooseascooter.com

WA R R A N T Y

Distributors ONLY warrant products with an active

Warranty Registration

Contents Introduction

Introduction 1

Parts diagram 2

Warnings 3

Battery use 5

Assembling the 14

SEA-DOO

AQUA MASTER

Getting started 17

Care & Maintenance 18

- Rechargeable Battery & Charger Care 18

- Storing the SEA-DOO

AQUA MASTER 19

Trouble Shooting 20

Technical Specifications 26

The SEA-DOO

AQUA MASTER is easy to assemble,

easy to drive and safe.

Please take time to study this User Manual before

using your SEA-DOO

AQUA MASTER.

Please keep the User Manual as it contains important

information.

Discarded electric appliances are

recyclable and should not be discarded

in the domestic waste! Please actively

support us in conserving resources and

protecting the environment by returning

this appliance to the collection centres

(if available).

Parts Diagram

• This AQUA MASTER is NOT A BOAT.

• Use in a pool or in calm water and close to shore.

• Do not use in open waters, in waves, wakes or in bad

weather conditions as it may not allow you to come back to

shore.

• Read the User Manual carefully before using the AQUA

MASTER.

• Keep the packaging as it contains important information.

• Children under 14 years old should NEVER operate the

AQUA MASTER.

• An adult must be responsible for battery safety at all times,

during use, storage and charging.

• The AQUA MASTER is not for use by more than two

riders, not exceeding 400 lbs/181 kg.

• DO NOT operate the AQUA MASTER for long periods out

of the water to avoid damage.

• Never stick body parts, clothing or other objects in the

vicinity of propeller.

• DO NOT wear loose or flowing clothing that could be

drawn into the propeller.

• DO NOT use at night or in low light situation.

• Always wear a Approved Personal Flotation Device /

Approved Life-Preserver when using the AQUA MASTER.

• Particular care should be exercised when using the

AQUA MASTER near anybody with long hair.

• Users with long hair should tie it up or wear a swimming

cap when using the AQUA MASTER.

• ALWAYS inspect the area to ensure it is free of hazards or

obstacles, such as swimmers before using the AQUA

MASTER. NEVER ride over swimmers or other objects.

• ALWAYS ensure the battery is fully charged before using

the AQUA MASTER.

• The AQUA MASTER is to be operated in water only when

fully assembled in accordance with the instructions.

• Do not use alcohol or mind-altering drugs prior to using

this product.

• ALWAYS keep the

AQUA MASTER

out of direct sunlight

when not in use. HEAT KILLS BATTERIES.

• When propeller becomes intermittent, battery is low and

needs recharging.

• Always charge battery to its fullest before using the AQUA

MASTER. After charging is complete the battery will

continue to off gas. Wait at least 30 minutes after charging

before remove the battery from the charger or placing the

battery into the battery housing. Failure to do so could

result in an explosion.

• ALWAYS remove the battery from the unit when not in use.

• DO NOT store the battery in the unit.

• THIS IS NOT a life saving device.

• DO NOT leave child unattended while device is in use.

• NEVER leave in or near the water when not in use.

• NEVER tow from any vehicle.

• Adults should inflate the Chambers in numbered

sequence.

• ALWAYS use an approved Life-Preserver.

• DO NOT use in high winds, rapid currents, open water or

dangerous tides.

Fig.1

Back

Inflatable

Steering Unit

ON/OFF Trigger

Master Switch

Steering Column

Steering Column Sleeve

Nozzle

Inner Nose Cone

Inner Nose Cone Seal

Repair Kit

Rechargeable Battery

Charger

Propeller

Battery Housing

Nose Cone

Latch

Buoyancy Foam

Propulsion Unit

Nylon Cover

Charger Jack

Battery Charging Socket

Battery Housing Cable

Flange

Front Grille

Rear Grille

Inflatable Chamber A

Inflatable Chamber B

Inflatable Chamber C & D

silicone ring

Pump

WARNINGS

• This AQUA MASTER is NOT A BOAT.

• Use in a pool or in calm water and close to shore.

• Do not use in open waters, in waves, wakes or in bad

weather conditions as it may not allow you to come back to

shore.

• Read the User Manual carefully before using the AQUA

MASTER.

• Keep the packaging as it contains important information.

• Children under 14 years old should NEVER operate the

AQUA MASTER.

• An adult must be responsible for battery safety at all times,

during use, storage and charging.

• The AQUA MASTER is not for use by more than two

riders, not exceeding 400 lbs/181 kg.

• DO NOT operate the AQUA MASTER for long periods out

of the water to avoid damage.

• Never stick body parts, clothing or other objects in the

vicinity of propeller.

• DO NOT wear loose or flowing clothing that could be

drawn into the propeller.

• DO NOT use at night or in low light situation.

• Always wear a Approved Personal Flotation Device /

Approved Life-Preserver when using the AQUA MASTER.

• Particular care should be exercised when using the

AQUA MASTER near anybody with long hair.

• Users with long hair should tie it up or wear a swimming

cap when using the AQUA MASTER.

• ALWAYS inspect the area to ensure it is free of hazards or

obstacles, such as swimmers before using the AQUA

MASTER. NEVER ride over swimmers or other objects.

• ALWAYS ensure the battery is fully charged before using

the AQUA MASTER.

• The AQUA MASTER is to be operated in water only when

fully assembled in accordance with the instructions.

• Do not use alcohol or mind-altering drugs prior to using

this product.

• ALWAYS keep the

AQUA MASTER

out of direct sunlight

when not in use. HEAT KILLS BATTERIES.

• When propeller becomes intermittent, battery is low and

needs recharging.

• Always charge battery to its fullest before using the AQUA

MASTER. After charging is complete the battery will

continue to off gas. Wait at least 30 minutes after charging

before remove the battery from the charger or placing the

battery into the battery housing. Failure to do so could

result in an explosion.

• ALWAYS remove the battery from the unit when not in use.

• DO NOT store the battery in the unit.

• THIS IS NOT a life saving device.

• DO NOT leave child unattended while device is in use.

• NEVER leave in or near the water when not in use.

• NEVER tow from any vehicle.

• Adults should inflate the Chambers in numbered

sequence.

• ALWAYS use an approved Life-Preserver.

• DO NOT use in high winds, rapid currents, open water or

dangerous tides.

Battery Use

RE-CHARGE THE BATTERY

AT LEAST

MONTHS

EVERY

MONTHS

WARNING

BATTERY SAFETY

• Must remove and store the

battery separately from the unit

when not in use!

• Must re-charge the battery after

use WITHIN 24 HOURS.

• Must re-charge the battery at

least EVERY THREE MONTHS

when not in use.

User Manual must be read and

understood before use.

Please read and follow the

Battery Safety Instruction.

Incorrect battery maintenance

may reduce the battery life and

influence its function.

www.seadooseascooter.com

CAUTION

• Your AQUA MASTER is supplied with a battery that

needs to be treated carefully as it will release potentially

explosive gasses during its normal cycle of use (off

gassing). Please read the entire manual thoroughly and

follow all instructions. Failure to do so can result in an

explosion occurring.

• Always remove the battery from your AQUA MASTER

when it is not in use and store separately in a well

ventilated area where it is out of the reach of children and

away from heat and ignition sources.

• Do not install the battery in your AQUA MASTER until

immediately prior to using it.

• Before disconnecting/connecting any cables, open the

nose cone and allow two minutes for any explosive

gases to dissipate.

• Do not use/store/charge the battery in temperatures

above 40ºC (104ºF) as excessive off gassing may occur.

Keep the battery and AQUA MASTER in the shade when

not in use.

• Always ensure the unit is dried thoroughly before

opening the Nose Cone.

• Only use the charger supplied with the AQUA MASTER.

• The battery supplied with your AQUA MASTER releases

a potentially explosive gas during charging. Charging

should only take place in a well ventilated area, away

from children and naked flames or other ignition sources

(cigarettes, sparks). Never charge the battery whilst still

in the AQUA MASTER.

• Charge the battery as soon as possible after use

within 24 hours.

Battery Use

CAUTION

• Always charge the battery to the fullest before using

the AQUA MASTER.

• Always remove the battery from the battery housing

before charging.

• Always connect charger jack to the battery first and then

plug charger into the mains.

• After charging, disconnect from the mains first and then

disconnect the battery from the charger.

• After charging is complete the battery will continue to off

gas. Wait at least 30 minutes after charging before

placing the battery into the battery housing. Failure to do

so could result in an explosion.

• Do not place battery into your AQUA MASTER until

immediately before use.

• Remove battery from charge once fully charged.

• Never charge the battery in a sealed container.

• Never charge the battery near water.

• Never short circuit the battery or battery connectors.

• Always ensure the charger is dry before use.

• The charger gets quite warm in use – this is normal.

• If in doubt of the state of the battery, recharge it until

the indicator on the battery charger indicates a full

charge.

Battery Use

19. Ensure the Vent O Ring is fitted correctly (See Fig.8).

20. Screw in the Vent Plug tightly to seal the vent (See

Fig.9).

21. Replace the Buoyancy

Foam (See Fig.10).

CAUTION

• If the battery is not to be used for an extended period,

store it in a well ventilated area away from children,

heat and ignition sources and recharge it every three

months to maintain charge and avoid excess off

gassing. DO NOT store the battery inside the AQUA

MASTER.

• If the battery appears damaged or will not charge fully,

the battery must be replaced. If battery life is noticeably

reduced, the battery should be replaced.

• The Rechargeable Battery will give you approximately

one hour of use - always make sure you have enough

power left to return.

• The battery supplied with your AQUA MASTER should

last about 200 cycles or two years before it should be

replaced. Please contact your local customer service

centre/distributor. Using a battery in excess of these

recommendations can result in excessive of gassing of

explosive gas.

Charging the battery

For Battery charging follow these instructions.

1. Always ensure that the Master Switch is OFF (See

Fig.16).

2. Always ensure that the SEA-DOO

AQUA MASTER is

out of the water, dry and placed in a dry area.

3. Lift and rotate the Latches and remove them from the

Nose Cone (See Fig.11).

4. Remove the Nose Cone and Buoyancy Foam.

5. Open the Vent Plug by unscrewing it (

See Fig.2).

6. Remove the Inner Nose Cone. To do this, first feed the

silicone ring (provided with this manual) through the

latch holes in the Inner Nose Cone and hook over the

hooks on the Battery Housing (see figure 3). Then screw

the Pump Nozzle onto the Vent Hole and pump air into

the Battery Chamber until the Inner Nose Cone pops off

and then remove the silicone ring.

7. Allow two minutes for any gasses to dissipate.

Low Battery Alert

When Propeller becomes intermittent

, Battery is low and

needs recharging.

When ON/OFF Trigger is depressed continuously, Propeller

stops 2 seconds every 10 seconds.

Battery Use

14. Allow battery to stand for 30 minutes before using it.

15. Unplug the Battery

Charging Socket from

the Charger Jack and

reconnect to the

Battery Housing

Cable.

16. Tidy up the cables

around the battery

(See Fig.5).

17.

Make sure the sealing

surface is clean and

lubricated before

replacing the Inner

Nose Cone (See Fig.6).

18.

Replace the Inner

Nose Cone making

sure the key is aligned

correctly and the

flange in touch with the

edge of Battery

Housing (See Fig.7).

Fig.2

Unscrewing the vent plug

Allow gasses to dissipate

8. Disconnect the Battery cable from the Battery Housing

Cable by pressing the locking feature (See Fig.4).

(The cable will be disconnected when you first receive

your unit.)

9. Remove the battery and place on a level surface

10.

Connect the Battery Charging Socket to the Charger Jack.

11. Plug Charger into mains, and turn on the supply.

12. Charging will take 6 to 8 hours for a fully discharged

battery. When the battery is charging the LED on the

Charger remains RED, when the battery is charged the

LED appears flashing RED.

13. Unplug the Charger from the mains.

22. Replace the Nose Cone making sure the key is

aligned correctly. Insert and then rotate the Latches,

you will hear "click" sound once the Latches are

engaged (See Fig.11).

19. Ensure the Vent O Ring is fitted correctly (See Fig.8).

20. Screw in the Vent Plug tightly to seal the vent (See

Fig.9).

21. Replace the Buoyancy

Foam (See Fig.10).

Charging the battery

For Battery charging follow these instructions.

1. Always ensure that the Master Switch is OFF (See

Fig.16).

2. Always ensure that the SEA-DOO

AQUA MASTER is

out of the water, dry and placed in a dry area.

3. Lift and rotate the Latches and remove them from the

Nose Cone (See Fig.11).

4. Remove the Nose Cone and Buoyancy Foam.

5. Open the Vent Plug by unscrewing it (

See Fig.2).

6. Remove the Inner Nose Cone. To do this, first feed the

silicone ring (provided with this manual) through the

latch holes in the Inner Nose Cone and hook over the

hooks on the Battery Housing (see figure 3). Then screw

the Pump Nozzle onto the Vent Hole and pump air into

the Battery Chamber until the Inner Nose Cone pops off

and then remove the silicone ring.

7. Allow two minutes for any gasses to dissipate.

1110

14. Allow battery to stand for 30 minutes before using it.

15. Unplug the Battery

Charging Socket from

the Charger Jack and

reconnect to the

Battery Housing

Cable.

16. Tidy up the cables

around the battery

(See Fig.5).

17.

Make sure the sealing

surface is clean and

lubricated before

replacing the Inner

Nose Cone (See Fig.6).

18.

Replace the Inner

Nose Cone making

sure the key is aligned

correctly and the

flange in touch with the

edge of Battery

Housing (See Fig.7).

Fig.3

Fig.4

Battery

Charging

Socket

Battery

Housing

Cable

Press here to release and pull to disconnect

8. Disconnect the Battery cable from the Battery Housing

Cable by pressing the locking feature (See Fig.4).

(The cable will be disconnected when you first receive

your unit.)

9. Remove the battery and place on a level surface

10.

Connect the Battery Charging Socket to the Charger Jack.

11. Plug Charger into mains, and turn on the supply.

12. Charging will take 6 to 8 hours for a fully discharged

battery. When the battery is charging the LED on the

Charger remains RED, when the battery is charged the

LED appears flashing RED.

13. Unplug the Charger from the mains.

Fig.5

Fig.6

Ensure sealing

surface is clean

Fig.7

Press down

Flange

Ensure the key

is aligned correctly

22. Replace the Nose Cone making sure the key is

aligned correctly. Insert and then rotate the Latches,

you will hear "click" sound once the Latches are

engaged (See Fig.11).

19. Ensure the Vent O Ring is fitted correctly (See Fig.8).

20. Screw in the Vent Plug tightly to seal the vent (See

Fig.9).

21. Replace the Buoyancy

Foam (See Fig.10).

Charging the battery

For Battery charging follow these instructions.

1. Always ensure that the Master Switch is OFF (See

Fig.16).

2. Always ensure that the SEA-DOO

AQUA MASTER is

out of the water, dry and placed in a dry area.

3. Lift and rotate the Latches and remove them from the

Nose Cone (See Fig.11).

4. Remove the Nose Cone and Buoyancy Foam.

5. Open the Vent Plug by unscrewing it (

See Fig.2).

6. Remove the Inner Nose Cone. To do this, first feed the

silicone ring (provided with this manual) through the

latch holes in the Inner Nose Cone and hook over the

hooks on the Battery Housing (see figure 3). Then screw

the Pump Nozzle onto the Vent Hole and pump air into

the Battery Chamber until the Inner Nose Cone pops off

and then remove the silicone ring.

7. Allow two minutes for any gasses to dissipate.

1312

14. Allow battery to stand for 30 minutes before using it.

15. Unplug the Battery

Charging Socket from

the Charger Jack and

reconnect to the

Battery Housing

Cable.

16. Tidy up the cables

around the battery

(See Fig.5).

17.

Make sure the sealing

surface is clean and

lubricated before

replacing the Inner

Nose Cone (See Fig.6).

18.

Replace the Inner

Nose Cone making

sure the key is aligned

correctly and the

flange in touch with the

edge of Battery

Housing (See Fig.7).

8. Disconnect the Battery cable from the Battery Housing

Cable by pressing the locking feature (See Fig.4).

(The cable will be disconnected when you first receive

your unit.)

9. Remove the battery and place on a level surface

10.

Connect the Battery Charging Socket to the Charger Jack.

11. Plug Charger into mains, and turn on the supply.

12. Charging will take 6 to 8 hours for a fully discharged

battery. When the battery is charging the LED on the

Charger remains RED, when the battery is charged the

LED appears flashing RED.

13. Unplug the Charger from the mains.

Fig.8

O Ring correctly fitted into

groove and lubricated

Inner Nose Cone

partial enlarged view

Fig.9

Fig.10

Buoyancy

Foam

22. Replace the Nose Cone making sure the key is

aligned correctly. Insert and then rotate the Latches,

you will hear "click" sound once the Latches are

engaged (See Fig.11).

Lift and rotate to unlock

Rotate and click

to lock

Fig.11

Assembling the SEA-DOO

AQUA MASTER

1514

1. Use a pump (not included), to blow up the Inflatable.

Make sure that the valve for each chamber is properly

closed once inflated.

Adults should inflate the chambers in numbered

sequence. (See Fig. 1)

Chamber C & D >

Chamber A >

Chamber B

DO NOT OVER INFLATE THE INFLATABLE.

2. Connect the Steering Column to the Propulsion Unit.

(See Fig.2) You will hear a "click" sound once the

Steering Column has been correctly connected.

3a. Slide the Steering Sleeve into the hole in the Inflatable

from the top.

3b. Slide Steering Column/Propulsion Unit assembly from

the bottom of the inflatable through the Steering

Sleeve. You will hear a "click" sound once the Steering

Column has completely passed through the Steering

Sleeve. (See Fig.13)

Tip: If the Steering Column Sleeve is stuck, pour some

water to lubricate and then push it down.

Fig.12

Fig.13

4. Attach the Steering Unit to the Steering Column - you

will hear a "click" sound once it has been properly

attached (See Fig.14).

Make sure the Propulsion Unit and Steering Unit are

aligned correctly (See Fig.15).

The SEA-DOO

AQUA MASTER is ready to use. Please

see page 17 - "Getting Started".

Fig.14

Fig.15

Getting Started

1716

When you buy the SEA-DOO

AQUA MASTER the battery

is disconnected and needs to be charged. Follow the

safety cautions on page 5 to 8 and charging instructions

on pages 9 to 13.

To use SEA-DOO

AQUA MASTER, please follow these

instructions.

1. Charge the battery and install just before use.

2. Make sure that the Vent Plug is closed.

3. Place the SEA-DOO

AQUA MASTER in the water.

4. Sit on the SEA-DOO

AQUA MASTER - a Approved

Personal Flotation Device / Approved Life-Preserver

should always be worn.

5. Turn the Master Switch to ON position (See Fig.16).

6. The rider simply has to pull the ON/OFF Trigger to start,

turn the steering unit to maneuver and release the

Trigger to stop.

CAUTION:

When Propeller becomes intermittent, battery is low and

needs recharging.

To replace a flat battery with a fully charged battery

Follow the steps 1 to 7 on page 9, to open the

Propulsion Unit

Unplug the Battery Charging Socket by pressing the

locking feature (See Fig.4).

3. Remove the flat Battery.

4. Install the charged Battery in the correct orientation -

tidy up the cables around the battery (See Fig.5).

Follow steps 17 to 22 on page 11, 12 and 13 to close

the Propulsion Unit

Buying Batteries

Additional standard or extended batteries can be

purchased separately. Contact your local customer service

centre/distributor to purchase them.

Fig.16

OFF

CAUTION:

When propeller becomes intermittent,

battery is low and needs recharging.

ATTENTION:

Lorsque l’hélice perd de sa puissance,

la batterie doit être rechargée.

Care And Maintenance

1918

Rechargeable Battery and Charger Care

1. Please read and understand important Battery Use

safety information on pages 5, 6, 7 and 8.

2. The battery supplied with your

AQUA MASTER should

last about 200 cycles or two years before it should be

replaced. Please contact your local customer service

centre/distributor. Using a battery in excess of these

recommendations can result in excessive of gassing of

explosive gas.

3. ALWAYS remove the battery from the AQUA MASTER

immediately after use.

4. DO NOT STORE BATTERY IN AQUA MASTER.

Storing the SEADOO

AQUA MASTER

1. Always rinse the AQUA MASTER in fresh water and

allow it to dry before storage.

2. Unclip the Steering Unit, remove the Steering Column

Sleeve, the Propulsion Unit and Steering Column and

unclip the Steering Column.

Tip: If the Steering Column Sleeve is stuck, pour some

water over it to lubricate and then remove.

3. Open the Inner Nose Cone and remove the

rechargeable battery (see also section on Rechargeable

Battery Care).

4. Deflate the inflatable fully.

5. Store the AQUA MASTER in the original box in a dry

place - ambient temperature for storage should be within

-20ºC to 40ºC (-4ºF to 104ºF).

6. ALWAYS store your Propulsion Unit vertically when not

in use to prevent deformation of the Nozzle.

Trouble Shooting

2120

If the SEA-DOO

AQUA MASTER does not work:

1. Check the Battery is fully charged, if in doubt of battery

state, recharge the Battery until Charger indicates full

charged (indicator flashing RED).

2. Make sure the Rechargeable Battery connector is

connected.

3. Make sure the Master Switch is in the ON position.

4. Make sure the Battery compartment is dry.

5. Make sure the Propeller is not blocked.

Blocked Propeller

If the Propeller becomes blocked first try and remove the

obstruction by removing the front grilles. If this is not

possible the back grille and Propeller can be removed.

Under normal use the grilles must not be removed.

Removing the front grille to remove an obstruction

1. Remove the Propulsion Unit from the water.

2. Make sure the Master Switch is in the OFF position.

3. Insert a screw driver (See Fig.17) to remove the two

grille pins.

4. Unclip grille (See Fig.18).

5. Remove obstruction.

6. Reassemble grille and insert clips.

Removing rear grille and Propeller to remove obstruction

1. Remove the Propulsion Unit from the water.

2. Make sure the Master Switch is OFF.

3. Remove the battery - see page 9, step 1-9.

4. Unscrew the six rear grille screws (See Fig.19).

5. Whilst holding the Propeller, use an M6 socket to remove

the nut from the Propeller shaft (See Fig.20).

9. Replace the washer(s) and nut and tighten with the

socket whilst holding the Propeller making sure it is

securely fastened (See Fig.22).

10. Replace the grille

11. Replace the battery.

6. Slide the Propeller off the shaft, taking care not to lose the

drive pin or washers.

7. Remove the blockage from the Propeller.

Replace the drive pin (if removed) (See Fig.21) and

Propeller. Turn the Propeller slowly until you locate the pin

and push the Propeller fully on.

Fig.18

Fig.17

1 2

Front grille Front grille

2322

Removing rear grille and Propeller to remove obstruction

1. Remove the Propulsion Unit from the water.

2. Make sure the Master Switch is OFF.

3. Remove the battery - see page 9, step 1-9.

4. Unscrew the six rear grille screws (See Fig.19).

5. Whilst holding the Propeller, use an M6 socket to remove

the nut from the Propeller shaft (See Fig.20).

9. Replace the washer(s) and nut and tighten with the

socket whilst holding the Propeller making sure it is

securely fastened (See Fig.22).

10. Replace the grille

11. Replace the battery.

Sand or Grit on Seals

Sand or grit is the enemy of seals. Correct maintenance and

care is essential. To remove sand or grit from the seals,

rinse the seals in fresh water and apply fresh lubricant. If

there is sand inside the Battery Housing, gently brush the

sand from the unit taking care not to scratch the sealing

surfaces.

6. Slide the Propeller off the shaft, taking care not to lose the

drive pin or washers.

7. Remove the blockage from the Propeller.

Replace the drive pin (if removed) (See Fig.21) and

Propeller. Turn the Propeller slowly until you locate the pin

and push the Propeller fully on.

Fig.19

Rear grille

Fig.20

Drive Pin In Position

Fig.21

Nut

Washers

Drive pin

Propeller hub

Fig.22

Repairing the Inflatable

A repair kit is included in case the inflatable is accidentally

punctured, to repair:

1. Locate the puncture - this can be done by inflating the

inflatable and looking for air bubbles.

2. Deflate the inflatable and make sure it is completely dry.

3. Clean punctured area and dry the area.

4. Using inflatable repair kit apply glue around

punctured area.

5. Use repair PVC sheet, cut so it is 5mm bigger around

the punctured area.

6. Stick the repair sheet on top of the punctured area.

7. Let it dry for 2 hours.

8. Inflate the inflatable and check there is no air leakage

before use.

AQUA MASTER cuts out

To protect the electronic circuit of your AQUA MASTER

from damage a safety mechanism has been built in that

cuts the power if a wall or rock or other immovable object

is hit. If this occurs simply wait for a short period to allow

the AQUA MASTER to reset itself and resume use.

Accidental Flooding

Be sure to keep the seals sand and grit free to ensure they

keep water out and to close the vent plug after accessing

the battery chamber. However, should the seals not be

clean or the vent plug left open and water enter the battery

chamber, your AQUA MASTER will not be damaged as it is

designed for protection against accidental flooding.

If water enters the battery chamber the Propulsion Unit will

automatically stop functioning. If this occurs

1. Remove the AQUA MASTER from the water if it is safe

to do so.

2. Remove nose cone and tip out excess water.

3. Wait two minutes for any gases to dissipate, then

remove the battery.

4. If salt water has entered, rinse battery and battery

housing with fresh water.

5. Dry housing and battery thoroughly.

For more information on

Sea-Doo

Seascooter

™

Products

(

Warranty, Customer Care / Maintenance,

Parts & Battery Purchase

)

PLEASE VISIT

www.seadooseascooter.com

SEA-DOO

and the BRP logo are trademarks

of Bombardier Recreational Products Inc. or its affiliates,

used under licence to Stallion (asia) Ltd.

For more information on SEA-DOO

products visit www.sea-doo.com

Technical Specifications

*Normal Use

The definition of normal use is based on the average general time

of use the user activates the seascooter in the water

∆

Continuous Use

The definition of continuous use is based on a fully charged battery

were by the seascooter is used continuously in a swimming pool or

open water without stopping.

L 81 inches x W 42.5 inches x H 25.6 inches

(L 206 x W 108 x H 65 cm)

Inflatable

Dimensions

23.8 inches x 36.2 inches x 21 inches

(60.4 x 92 x 54 cm)

Propulsion

Dimensions

18.3 lbs (8.3 kg) (with rechargeable battery)

1 x 12V / 12Ah rechargeable battery

Run up to 1.5 hours with normal use

∆

Continuous use up to 30 minutes (high speed)

Up to 2.5 mph (4.0 km/

(at Carrying weight : 60kg / 132lbs)

Drive Unit Weight

8.8 lbs (4.0 kg)

Inflatable Weight

Battery Type

Battery Life /

Fully Charge

Speed

This warranty does not cover any product that has been subject to misuse

negligence or accident, or that has been operated in any way contrary to the

operating instructions as specified in the User Manual. This warranty does not

apply to any damage to the product that is the result of improper maintenance

or to any product that has been altered or modified so as to change its

intended use. This warranty does not extend to repairs made necessary by

normal wear or by the use of parts or accessories which are either

incompatible with the product or adversely affects its operation, performance

or durability.

In addition, this warranty does not cover items that

experience normal wear and tear.

ALL IMPLIED WARRANTIES ARE LIMITED IN THE DURATION TO THE

WARRANTY PERIOD. AND SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR

OTHERWISE, ARE DISCLAIMED IN THEIR ENTIRETY AFTER THE

E X P I R AT I O N O F T H E APPROPRIATE WA R R A N TY P E R IO D .

THE DISTRIBUTOR’S OBLIGATION UNDER THE WARRANTY IS

STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR

REPLACEMENT OF DEFECTIVE PARTS AND RETURN OF THE

PRODUCT TO THE CUSTOMER. THE DISTRIBUTOR DOES NOT ASSUME

OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY OTHER

OBLIGATION.

THE DISTRIBUTOR ASSUMES NO RESPONSIBILITY FOR INCIDENTAL,

CONSEQUENTIAL OR OTHER DAMAGES INCLUDING, BUT NOT LIMITED

TO EXPENSE OF RETURNING THE PRODUCT TO THE DISTRIBUTOR,

LOSS OF USE OF PRODUCT AND LOSS OF TIME OR INCONVENIENCE.

EXCLUSIONS

BATTERY. This warranty does not include the battery.

CUSTOMER ENQUIRIES

If your unit is not operating, please refer to your User Manual before

contacting our Customer Service Centre. For any damage or repair work

required, please do not return your product to the store where it was

purchased.

RETURN / REPAIR POLICY

Customers must call our Customer Service Centre and ask for a Return /

Repair Authorization Number before sending the product to the Service

Centre. Returned products must be shipped with original packaging including

the polystyrene packing material and all defective parts. Please contact our

Customer Service Centre for assistance in handling your case.

For any questions or queries you may have regarding your

SEA-DOO

SEASCOOTER™, please follow the below steps for

easy and fast resolution:

- STEP 1-

Please read your User Manual. For a copy of the User Manuals, please visit

www.seadooseascooter.com

- STEP 2-

Go to www.seadooseascooter.com and see our FAQ section to find instant

answers.

- STEP 3-

Contact one of our Customer Service representatives at the Customer Service

Centre in your region.

RETURN / REPAIR PROCEDURE

1. Call the Customer Service Centre for your Return / Repair Authorization

Number.

2. Make a copy of your Proof of Purchase (receipt).

3. Pack the defective unit in its original packaging including the polystyrene

foam and include the unit and all defective parts.

4. Attach the copy of your Proof of Purchase (receipt) to the outside of the box

(clearly visible), together with the Return / Repair Authorization Number.

5. Ship the package to the Service Centre.

PLEASE NOTE: Deliveries that do not have the Proof of Purchase (receipt)

and Return / Repair Authorization Number attached clearly to the outside of

the box, will not be accepted by the Service Centre.

UNITED STATES SEA-DOO