Coburn Straightaway 50 Operating instructions

Brand: Coburn

Model: Straightaway 50

Type: Operating instructions

From Edge of Door 50mm

2 x 'W' Minimum

'W'

= = =

Track end piece

1-18 Track

24.5

Max. 2400mm

16-20

6-12

DETAIL Hanger

SCALE 1 : 2

Hanger

assembly

DETAIL K

SCALE 1 : 2

Guide

STRAIGHTAWAY 50

TECHNICAL DATA (Fitting Instructions)

Coburn Sliding Systems Limited, Unit 1, Cardinal West, Godmanchester PE29 2XN

Tel: +44 (0)20 8545 6680 Fax: +44 (0)20 8545 6720 , E-mail: [email protected] www.coburn.co.uk

TRACK LENGTH AND BRACKET SPACING

Track supplied in standard length 1800mm and

2400mm.

01030/40 brackets are supplied in packs of 3 or 4

complete with all screws. Equally space the side

fixing bracket along the length of the track.

Note: Track can also be Soffit mounted by

screwing throught the track into the support above.

ALL DIMENSIONS ARE IN mm

MAXIMUM DOOR WEIGHT 50kg

MAXIMUM DOOR HEIGHT 2100mm

DOOR THICKNESS 20 - 50mm

COMPONENTS SUPPLIED SEPARATELY

43-2 Aluminium Channel

Note: Hanger Pack includes 2 hangers

with nylon wheels and integral ball bearings,

1 pair of track end pieces, door guide,

spanner and fitting instructions.

TRACKSET COMPONENTS

01824

Hanger Pack 01050

Bracket Pack

1-005, 1-008

Aluminium Track 11824

Trackset Components

01818 01824

Hanger Pack

01050 1

Hanger Pack

01050 1

Bracket pack

01030 1

Bracket Pack

01040 1

Aluminium Track

11818 1

Aluminium Track

11824 1

Drill hole to

accommodate

retaining catch

Assembly of Timber door hanger

Thread hexagon nut on to pendant

bolt to within 5.5mm of head. Enter

bolt in under side of hanger body to

engage with thread in to the body. Screw

bolt in until clear of nut.

Screw door plate to door, flush with

inside edge and such that the screw

holes are

clear of stiles. With hangers in track,

offer door up and engage pendant bolts

with slots of door plate, adjust vertically

and laterally then tighten hexagon nut.

Pendant

Bolt

Hexagon

Nut

Square

Nut

Door Plate

2-7/8" - 3-5/16"

29/32" - 1-11/32"

1-21/32"

25/64"

25/32" - 1-31/32"

13/64"

12.50

25mm - 38mm

6-12

DETAIL L

SCALE 1 : 2

Hexagon Nut

Hanger

Fixing Plate

Pendant Bolt

DETAIL M

SCALE 1 : 2

Screws

Guide

DETAIL P

SCALE 1 : 3

Once the door is hung, fully open the door and place 44-373 guide half

way into the routing and fix with a screw into the floor.

Fully close the door and fix the remaing screw to secure guide on the

floor.

Note: the guide must remain inside the routing at all times.

CAUTION: Do not wind the Pendant Bolt all the way past the top of the Hanger, as

this will stop the system from working properly

For side fixing brackets, drill Ø5.5mm holes along the

centre line of the track. Drill the first and last holes so

they are 50mm from the ends of the track, space the

remaining holes equally betweeen these holes.

Assemble brackets to track as shown in 'A' before fixing

onto wall.

Insert hangers with pendant bolts into track (see 'B' or 'C')

followed by assembly of the track end piece.

44-373 door guide for internal doors over 1200mm wide.

One at each end of door and running in 42-2 floor

aluminium channel.

Door preparation

Make a routing on the

bottom of the door

(15x15mm)

for the 44-373 guide.

If Soffit mounting the track, pre-drill Ø4mm holes along

the centre line of the track. Space the holes equally

across the length of the track. First and last holes

should be 50mm from the ends of the track. Use the

wall screws in the bracket pack to then secure the track

through the predrilled holes into the support above.

Coburn Straightaway 50 Operating instructions

Coburn Straightaway 50 Operating instructions

Coburn Straightaway 50 Operating instructions

Other documents