2. Coburn
  3. Straightaway 50
Straightaway 50

Coburn Straightaway 50 Operating instructions

  • Hello! I'm your chat assistant. I've reviewed the Technical Data document for the COBURN Sliding System STRAIGHTAWAY 50. This document details the installation and specifications for the system, including maximum door weight, height, and thickness. It also outlines the components included in the hanger pack and provides mounting instructions. I'm ready to answer your questions about this product.
  • What is the maximum door weight supported by the system?
    What is the maximum door height for this system?
    What door thicknesses are compatible with this system?
    What are the standard track lengths available?
    What is included in the hanger pack?
From Edge of Door 50mm
2 x 'W' Minimum
'W'
50
= = =
50
Track end piece
1-18 Track
24.5
Max. 2400mm
16-20
6-12
DETAIL Hanger
SCALE 1 : 2
Hanger
assembly
DETAIL K
SCALE 1 : 2
Guide
STRAIGHTAWAY 50
TECHNICAL DATA (Fitting Instructions)
Coburn Sliding Systems Limited, Unit 1, Cardinal West, Godmanchester PE29 2XN
Tel: +44 (0)20 8545 6680 Fax: +44 (0)20 8545 6720 , E-mail: [email protected] www.coburn.co.uk
TRACK LENGTH AND BRACKET SPACING
Track supplied in standard length 1800mm and
2400mm.
01030/40 brackets are supplied in packs of 3 or 4
complete with all screws. Equally space the side
fixing bracket along the length of the track.
Note: Track can also be Soffit mounted by
screwing throught the track into the support above.
ALL DIMENSIONS ARE IN mm
MAXIMUM DOOR WEIGHT 50kg
MAXIMUM DOOR HEIGHT 2100mm
DOOR THICKNESS 20 - 50mm
COMPONENTS SUPPLIED SEPARATELY
43-2 Aluminium Channel
Note: Hanger Pack includes 2 hangers
with nylon wheels and integral ball bearings,
1 pair of track end pieces, door guide,
spanner and fitting instructions.
TRACKSET COMPONENTS
01824
Hanger Pack 01050
1
Bracket Pack
1-005, 1-008
1
Aluminium Track 11824
1
Trackset Components
01818 01824
Hanger Pack
01050 1
Hanger Pack
01050 1
Bracket pack
01030 1
Bracket Pack
01040 1
Aluminium Track
11818 1
Aluminium Track
11824 1
Drill hole to
accommodate
retaining catch
Assembly of Timber door hanger
.
Thread hexagon nut on to pendant
bolt to within 5.5mm of head. Enter
bolt in under side of hanger body to
engage with thread in to the body. Screw
bolt in until clear of nut.
Screw door plate to door, flush with
inside edge and such that the screw
holes are
clear of stiles. With hangers in track,
offer door up and engage pendant bolts
with slots of door plate, adjust vertically
and laterally then tighten hexagon nut.
Pendant
Bolt
Hexagon
Nut
Square
Nut
Door Plate
'
B
2-7/8" - 3-5/16"
29/32" - 1-11/32"
1-21/32"
25/64"
25/32" - 1-31/32"
13/64"
57
37
12.50
5
10
25mm - 38mm
6-12
15
15
L
DETAIL L
SCALE 1 : 2
Hexagon Nut
Hanger
Fixing Plate
Pendant Bolt
M
DETAIL M
SCALE 1 : 2
Screws
Guide
P
DETAIL P
SCALE 1 : 3
Once the door is hung, fully open the door and place 44-373 guide half
way into the routing and fix with a screw into the floor.
Fully close the door and fix the remaing screw to secure guide on the
floor.
Note: the guide must remain inside the routing at all times.
A
2
CAUTION: Do not wind the Pendant Bolt all the way past the top of the Hanger, as
this will stop the system from working properly
For side fixing brackets, drill Ø5.5mm holes along the
centre line of the track. Drill the first and last holes so
they are 50mm from the ends of the track, space the
remaining holes equally betweeen these holes.
Assemble brackets to track as shown in 'A' before fixing
onto wall.
Insert hangers with pendant bolts into track (see 'B' or 'C')
followed by assembly of the track end piece.
44-373 door guide for internal doors over 1200mm wide.
One at each end of door and running in 42-2 floor
aluminium channel.
C
Door preparation
Make a routing on the
bottom of the door
(15x15mm)
for the 44-373 guide.
If Soffit mounting the track, pre-drill Ø4mm holes along
the centre line of the track. Space the holes equally
across the length of the track. First and last holes
should be 50mm from the ends of the track. Use the
wall screws in the bracket pack to then secure the track
through the predrilled holes into the support above.
/