Altronix MOM5C Installation guide

Brand: Altronix

Model: MOM5C

Category: Security device components

Type: Installation guide

Altronix MOM5C is a multi-output power distribution module that converts one non-power-limited DC voltage input to five power-limited outputs, ideal for access control systems. It supports both fail-safe and fail-secure modes and offers supervised inputs and a form "C" dry output relay for triggering auxiliary devices or HVAC shutdown. With its UL listings and compact enclosure, the MOM5C provides reliable power distribution and control for various access control hardware.

MOM5C

Multi-Output Power Distribution Module

for Access Control

Installation Guide

Rev. 013019 More than just power.TM

Installing Company: _______________ Service Rep. Name: __________________________________

Address: _____________________________________________ Phone #: __________________

Altronix Corp.

140 58th St. Brooklyn, NY

LISTED

- 2 - MOM5C Installation Guide

Overview:

Altronix MOM5C multi-output power distribution module converts one (1) non power-limited DC voltage input to

five (5) power-limited outputs. Each output will route power to a variety of access control hardware and devices

which includes Mag Locks, Electric Strikes, Magnetic Door Holders, etc. These outputs will operate in both fail-

safe and fail-secure modes. Controlled trigger input is achieved through normally open (NO) or normally closed

(NC) supervised input or the polarity reversal from an FACP (Fire Alarm Control Panel). A form “C” dry output relay

will enable HVAC Shutdown, Elevator Recall or trigger auxiliary devices.

Specifications:

Agency Listings:

• UL294* 7th edition.

Access Control System Units.

UL1481 Standard for Safety for Fire Protective

Signaling Systems.

• MEA NYC Department of Buildings Approved.

• CSFM California State Fire Marshal Approved.

• NFPA72 compliant.

Input:

• 12VDC or 24VDC from power supply.

Output:

• Five (5) individual 12VDC or 24VDC power-limited

Class 2 outputs.

• Current limit is 2A @ 12VDC or 24VDC per output.

Visual Indicators:

• Red LEDs indicate condition of each power output.

• Power and input trigger LEDs.

Supervision:

• Fire Alarm Panel or Access Control System trigger

inputs. (NO or NC supervised trigger input and

polarity reversal trigger input).

• Output relay indicates that unit is triggered.

(Form “C” contact rated 1A @ 28VDC).

• Power fail supervision relay

(Form “C” contact rated 1A @ 28VDC).

Special Features:

• Will interface with most UL Listed Power Supplies.

Enclosure Dimensions:

8” x 7.25” x 3.5” (215.9mm x 190.5mm x 88.9mm).

*Access Control Performance Levels:

Destructive Attack - I; Endurance - IV; Line Security - I; Stand-by Power - I.

Installation Instructions:

1. Mount unit in the desired location. Mark and predrill holes in the wall to line up with the top two keyholes

in the enclosure. Install two upper fasteners and screws in the wall with the screw heads protruding. Place

the enclosure’s upper keyholes over the two upper screws, level and secure. Mark the position of the lower

two holes. Remove the enclosure. Drill the lower holes and install the two fasteners. Place the enclosure’s

upper keyholes over the two upper screws. Install the two lower screws and make sure to tighten all screws

(Enclosure Dimensions, pg. 8).

2. Connect DC output of the power supply to the terminals marked [– DC Input +] carefully observing polarity.

3. Connect door strikes (fail-secure) positive to terminals marked [1 through 5 Pos. (+) DC Output (Alarm)]

and negative to [NEG1] through [NEG5] (Fig. 7, pg. 6).

4. Connect mag locks, door holders (fail-safe) positive to terminals marked [6 through 10 Pos. (+) DC Output

(Stand-by)] and negative to [NEG1] through [NEG5] (Fig. 7, pg. 6).

5. To trigger the MOM5C from a FACP connect signaling circuit of FACP to terminals marked [– INPUT +].

Polarity is shown in alarm condition. Connect the wires on opposite sides of the screw.

6. To trigger the MOM5C using a supervised dry contact connect a 2.2K resistor in series to terminals marked

[TRIGGER] for a NC (Normally Closed) trigger input or connect a 2.2K resistor in parallel to terminals

marked [TRIGGER] for NO (Normally Open) trigger input (Fig. 7, pg. 6).

7. Connect the auxiliary devices that are to be triggered by the MOM5 to terminals marked [Dry Output]:

For Normally Open operation connect wires to the terminals marked [NO & C].

For Normally Closed operation connect wires to the terminals marked [NC & C].

Note: This relay will energize when the MOM5C is triggered.

8. Connect trouble reporting device to the terminals marked [Power Fail].

For Normally Open operation connect wires to the terminals marked [NO & C].

For Normally Closed operation connect wires to the terminals marked [NC & C].

Note: This relay will switch when power is lost to the MOM5C.

MOM5C Installation Guide - 3 -

Current Draw:

Input Voltage Stand-by Alarm

12VDC 0.024A 0.066A

24VDC 0.026A 0.074A

LED Diagnostic Table:

LED ON OFF

Power (Green) Normal operating condition. Power failure.

Trigger (Green) Input is triggered (alarm condition). MOM5 in stand-by (non-alarm condition).

Outputs (Red) Output tripped due to a short circuit or

overload condition. Normal operation.

Terminal Identification:

Terminal Legend Function/Description

– DC INPUT + 12VDC or 24VDC from power supply.

TRIGGER

Dry normally open [NO] or normally closed [NC] supervised (2.2K EOL resistor) input

trigger. A short or open circuit will transfer power from terminals marked [POS. (+) DC

OUTPUT (STAND-BY)] to terminals marked [POS (+) DC OUTPUT (ALARM)].

– INPUT +

Wet (5-30VDC) input trigger. Applying voltage to these terminals in the polarity shown

will transfer power from terminals marked [POS. (+) DC OUTPUT (STAND-BY)] to

terminals marked [POS. (+) DC OUTPUT (ALARM)] (e.g. fire alarm control panel

indications circuit).

NEG. 1

THROUGH NEG. 5 Supplies constant negative (–) voltage.

POS. (+) DC OUTPUT

(ALARM) 1-5

Supplies positive (+) voltage when dry trigger input or fire alarm wet trigger

input is applied.

POS. (+) DC OUTPUT

(STAND-BY) 6-10

Supplies positive (+) voltage in normal condition.

Power is removed when dry trigger input or fire alarm wet trigger input is applied.

NC, C, NO

DRY OUTPUT

When the MOM5 is triggered, the terminals marked [C and NO] will open and the

terminals marked [C and NC] will close. This output is used to trigger auxiliary devices.

(e.g. HVAC Shutdown, Elevator Recall etc.). Contact rating 1A @ 28VDC.

NC, C, NO

POWER FAIL

Form “C” contacts used for reporting no voltage is present at [– DC INPUT +]

terminals. Under normal conditions terminals marked [NO and C] are open,

[NC and C] are closed. A loss of power causes terminals marked [NO and C] to close

and [NC and C] to open. Contact rating 1A @ 28VDC.

- 4 - MOM5C Installation Guide

Fig. 1

Fig. 2

Fig. 3

Typical Application Diagrams:

MOM5C module shown with wet and/or dry normally

closed trigger inputs (Non-Latching):

MOM5C module shown with wet and/or dry normally

open trigger inputs (Non-Latching):

Two (2) or more MOM5C modules shown with wet and/or dry normally closed trigger inputs (Non-Latching):

TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED

EOL 2.2K

N.C. INPUT FROM

FACP OR ACCESS

CONTROL DEVICE

DC VOLTAGE INPUT

FROM FACP

SIGNALING

OUTPUT OR ACCESS

CONTROL DEVICE

(+)

(--)

TO TRIGGER INPUT

OF NEXT MOM5

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

TRIGGER NEG (-) INPUT POS (+)

EOL 2.2K

(+)

(-)

DC VOLTAGE INPUT

FROM FACP

SIGNALING

OUTPUT OR ACCESS

CONTROL DEVICE

N.C. INPUT FROM

FACP OR ACCESS

CONTROL DEVICE

TRIGGER NEG (-) INPUT POS (+)

EOL 2.2K

(+)

(-)

DC VOLTAGE INPUT

FROM FACP

SIGNALING

OUTPUT OR ACCESS

CONTROL DEVICE

N.O. INPUT FROM

FACP OR ACCESS

CONTROL DEVICE

TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED

EOL 2.2K

MOM5_S

ALTRONIX CORP.

BROOKLYN, NY 11220

MADE IN USA

MOM5_S

ALTRONIX CORP.

BROOKLYN, NY 11220

MADE IN USA

N.O. INPUT FROM

FACP OR ACCESS

CONTROL DEVICE

DC VOLTAGE INPUT

FROM FACP

SIGNALING

OUTPUT OR ACCESS

CONTROL DEVICE

(+)

(--)

TO TRIGGER INPUT

OF NEXT MOM5

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

Two (2) or more MOM5C modules shown with wet and/or dry normally open trigger inputs (Non-Latching):

MOM5C Installation Guide - 5 -

Fig. 4

Fig. 5

Fig. 6

TRIGGER

LED

TRIGGER NEG (-) INPUT POS (+

)

POWER

ON LED

N.C.

RESET

EOL 2.2K

(+)

(-)

DC VOLTAGE INPUT

FROM FACP

SIGNALING OUTPUT

N.O. INPUT

FROM FACP

SIGNALING

OUTPUT

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

TRIGGER

LED

TRIGGER NEG (-) INPUT POS (+)

POWER

ON LED

N.O. RESET

EOL 2.2K

(+)

(-)

DC VOLTAGE INPUT

FROM FACP

SIGNALING OUTPUT

N.C. INPUT

FROM FACP

SIGNALING

OUTPUT

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

MOM5C module shown with with wet and/or dry

normally open fire alarm trigger inputs

(Latching with Manual Reset):

MOM5C module shown with with wet and/or dry

normally closed fire alarm trigger inputs

(Latching with Manual Reset):

Typical Application Diagrams (cont’d):

TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED

N.O. RESET

EOL 2.2K EOL 2.2K

(+) (-)

DC VOLTAGE INPUT

FROM FACP

SIGNALING

OUTPUT OR ACCESS

CONTROL DEVICE

N.C. INPUT

FROM FACP

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

Two (2) MOM5C modules shown with wet and/or dry normally closed fire alarm trigger inputs

(Latching with Manual Reset):

TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED TRIGGER

LED

TRIGGER

- DC INPUT+

NEG (-) INPUT POS (+)

POWER

ON LED

EOL 2.2K

(+)

(-)

(+) (-)

N.C. RESET

EOL 2.2K

DC VOLTAGE INPUT

FROM FACP

SIGNALING

OUTPUT OR ACCESS

CONTROL DEVICE

N.O. INPUT

FROM FACP

NC C NO

DRY OUTPUT

NC C NO

POWER FAIL NC C NO

DRY OUTPUT

NC C NO

POWER FAIL

Two (2) MOM5C modules shown with wet and/or dry normally open fire alarm trigger inputs

(Latching with Manual Reset):

- 6 - MOM5C Installation Guide

Fig. 7

NC C NO

DRY OUTPUT

TRIGGER

LED

POWER

ON LED

678910

POS (+) DC OUTPUT (STANDBY)

NC C NO

POWER FAIL

TRIGGER

12345

POS (+) DC OUTPUT (ALARM)

NEG1 NEG2 NEG3 NEG4 NEG5 DC INPUT +

-- INPUT +

MOM5

TRIGGER

12VDC or 24VDC

FROM POWER SUPPLY

--- +

FROM FACP

SIGNALING

OUTPUT

FACP

EOL

2.2K EOL

2.2K

EOL

TRIGGER

INPUT

TRIGGER

INPUT

DOOR STRIKE

(FAIL-SECURE)

MAG LOCK

(FAIL-SAFE)

MOM5C Installation Guide - 7 -

Notes:

- 8 - MOM5C Installation Guide

Enclosure Dimensions (H x W x D):

8” x 7.25” x 3.5” (215.9mm x 190.5mm x 88.9mm)

7.25” (184.2mm)

3.625” (92mm)

1.25”

(31.8mm)

3.5” (88.9mm)

6.05” (153.7mm)

1.125”

(28.6mm)

1.125”

(28.6mm)

0.6” (15.2mm)0.6” (15.2mm)

2” (50.8mm)2” (50.8mm)

8.125” (206.4mm)

1”

(25.4mm)

1”

(25.4mm)

1”

(25.4mm)

1.25”

(31.75mm)

1.25”

(31.75mm)

1”

(25.4mm)

1”

(25.4mm)

5.25” (133.35mm)

6.05” (153.7mm)

3.5” (88.9mm)

Altronix is not responsible for any typographical errors.

––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––

140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056

website: www.altronix.com | e-mail: [email protected] | Lifetime Warranty

IIMOM5C G12U MEMBER

Altronix MOM5C Installation guide

Brand: Altronix

Model: MOM5C

Category: Security device components

Type: Installation guide

Download PDF

report

Altronix MOM5C Installation guide

Altronix MOM5C Installation guide

Related papers

Other documents