Fisher & Paykel W30SDEI Installation guide

Brand: Fisher & Paykel

Model: W30SDEI

Type: Installation guide

Fisher & Paykel W30SDEI is a warming drawer that provides ample space to accommodate a variety of food items, making it ideal for entertaining guests or keeping meals warm until ready to serve. With its sleek and stylish design, it seamlessly integrates into your kitchen cabinetry, complementing your existing appliances. The drawer features adjustable temperature settings, allowing you to customize the heat level to suit your specific needs.

INSTALLATION GUIDE

US CA

INTEGRATED W0SDEI

WARMING DRAWER

SAFETY AND WARNINGS

! WARNING!

Tip Hazard

This product may tip. Keep children away and

take care. Failure to follow this advice may

result in injury.

• Drawer must be secured in place by supplied

screws.

• Ensure there is a fixed shelf directly above

the drawer if it is not installed under another

product.

! WARNING!

Cut Hazard

Failure to use caution could result in injury.

• Take care: some edges may be sharp.

• Do not put fingers in the drawer when closing.

! WARNING!

Electric Shock Hazard

Failure to follow this advice may result in

electrical shock or death.

• If the product is damaged, switch the appliance

off and disconnect it from the mains to avoid

possible electric shock.

! WARNING!

420-630 lb

190-285 kg

Weight Hazard

Failure to follow this advice may result in

damage or personalinjury.

• Ensure the bottom shelf of the cabinetry can fully

support the weight of combined appliances.

SAFETY AND WARNINGS INTEGRATED WARMING DRAWER

READ AND SAVE THIS GUIDE

WARNING!

To reduce the risk of fire, injury to persons or damage when using the appliance, follow the

important safety guides listed below. Read all the instructions before using the appliance.

Installation

zPlease make this information available to the person installing the product.

zThe appliance must be installed by a qualified installer, or Fisher & Paykel trained and

supported service technician to avoid faulty electrical connection.

zEnsure the installation complies with all clearance requirements and applicable standards

and regulations.

zWhen installed in combination with a companion product, the companion product can be

placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be

able to support the weight of both products.

zEnsure the cabinetry is square and level and with correct dimensions.

zIf installing the appliance directly underneath an oven, ensure you do not damage the

oven’s lower trim. Fisher & Paykel does not accept any responsibility for any damage

resulting from incorrect installation.

zBefore installing the appliance, inspect for any signs of damage. Do not install or use

damaged appliances.

zBe careful when stacking the appliances on top of each other to avoid damage to the

appliances.

Electrical

zAll connections for electrical power and earthing must be done by a qualified electrician

and must comply with local codes and ordinances.

zBefore installation, ensure that the voltage and frequency listed on the data plate

corresponds with the household electrical supply.

zWhen combining with another appliance, ensure each appliance has its own power outlet.

Avoid sharing the power point to prevent accidental switching off of the appliance.

zEnsure your appliance is properly grounded (earthed).

zConnect the drawer to a properly rated, protected and sized power supply circuit to avoid

electrical overload.

zDo not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet

box) to connect the drawer to the power supply. Ensure the power supply cord is located

so that it will not be stepped on, tripped over or otherwise subject to damage or stress.

zEnsure there is a switched outlet in an easily accessible area within 35 7/16” (900mm) of

the centre rear of the product.

Servicing

zDo not repair or replace any part of the appliance unless specifically recommended in the

user guide. All other servicing should be done by a Fisher & Paykel trained and supported

service technician or qualified person.

zAlways disconnect the power supply before doing any installation, maintenance or repair

work.

zIf the power supply cord is damaged, it must be replaced by a qualified electrician or

Fisher & Paykel trained and supported service technician.

30" Warming Drawer,

Integrated style

WB30SDEI with Contemporary handle

30" Warming Drawer,

Integrated style

WB30SDEI with Professional handle

Remove the warming drawer and accessories box from the packaging. Recycle the materials

that can be reused. Dispose packaging materials in accordance with local regulations on waste

disposal.

Inspect the warming drawer for any signs of damage. Do not install the warming drawer if it

has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer.

UNPACK YOUR PRODUCT ELECTRICAL SPECIFICATIONS

RECYCLE

RESPONSIBLY

All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and

supported service technician.

WB30SDEI

Supply 110 VAC, 60 Hz

Service 10 amp circuit

Maximum Power 810 W

Power outlet* 3-prong grounding-type

Power cord (total length) 70 7/8" (1800mm)

* The power outlet must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.

Wire shelf (1)

Bracket spacer (1)

Installation guide (1)Service & Warranty

(1)

SERVICE & WARRANTY

SERVICE ET GARANTIE

ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ

SERVIZIO E GARANZIA

SERVICE & GARANTIE

HUOLTO JA TAKUU

SERVICE OG GARANTI

保修和维修

服務和保修 INSTALLATION GUIDE

US CA

INTEGRATED W30SDEI

WARMING DRAWER

User guide (1)

USER GUIDE

US CA

WARMING DRAWER

MINIMAL WB24SDEB2 & WB30SDEB1

CONTEMPORARY WB24SDEX2 & WB30SDEX1

PROFESSIONAL WB30SPEX1

INTEGRATED WB30SDEI1

5mm Hex key T20 star-head

screwdriver Level

PARTS SUPPLIED HANDLE KITS

TOOLS REQUIRED

T20 star head

wood screw (12) T20 star head

machine screw (6)

Side brackets (2) Bracket cover (2)

Square ruler

Contemporary style handle kit

The handle kit is not supplied and must be purchased separately through an authorised Fisher

& Paykel dealer. Visitfisherpaykel.com for more information.

Round handle (1x) M5x25 Hex screw (4x)

Square handle (1x) M5x25 Hex screw (4x)

MODEL CODES

Aluminium round

handle

AHS-OBDD-76S

MODEL CODES

Stainless steel square

handle

AHV2-WOWD

MODEL CODES

Aluminium square

handle

AHD3-OBWD-76SX

Aluminium square fine

handle

AHD5-OBDD-76SX

Black square fine

handle

AHD5-OBDD-76SB

Professional style handle kit

Round handle (1x) M5x25 Hex screw (4x)

MODEL CODES

Stainless steel round

handle

AHP3-OBWD-76S

Stainless steel round

flush handle

AHP3-OBWD-76SX

Round handle (1x) M5x25 Hex screw (4x)

PRODUCT DIMENSIONS

Actual product dimension may vary by ± 2 mm.

PRODUCT DIMENSIONS

WB30SDEI

IN MM

A Overall height 10 11/16 271

B Overall width* †28 9/16

- 28 3/4 725 -730

C Overall depth** 22 3/16 564

D Height of chassis 10 11/16 271

E Width of chassis*** 27 13/16 707

F Depth of chassis**** 21 9/16 547

G Distance from front of door

frame to rear of chassis flange 11/16 17

H Distance from side of chassis to

side of side bracket†3/8 - 7/16 9 - 12

I Height of door frame***** 10 1/2 267

J Depth of open drawer 16 1/2 419

K Height from top of door frame to

top of chassis 1/16 2

L Height from bottom of chassis to

bottom of door frame 1/16 2

* Including chassis flange and side brackets. Excluding custom front panel.

** Including power plug and door frame

*** Excluding chassis flange

**** Including power plug

***** Excluding custom panel

† Side brackets adjustable to fit cavity width

PRODUCT WEIGHT

WB30SDEI

LBS KG

Total weight of drawer* 75 34

*including packaging

PLAN

FRONT

ISOMETRIC

side bracket

PROFILE

chassis flange

bracket cover

FRONT PANEL DIMENSIONS

WB30SDEI

IN MM

A Height of custom panel min 10 1/2 min 267

B Width of custom panel min 29 15/16 min 760

C Depth of custom panel min 5/8 - max 13/16 min 16 - max 20

FRONT PANEL WEIGHT

WB30SDEI

LBS KG

Maximum weight of front panel* 11 5

* Including handle

The custom panel must be supplied by the customer to match the cabinetry.

CUSTOM PANEL DIMENSIONS

CABINETRY DIMENSIONS

WB30SDEI

INCHES MM

A Inside height of cavity* min 10 3/4 min 273

B Inside width of cavity min 28 9/16 -

max 28 3/4

min 725 -

max 730

C Inside depth of cavity min 22 5/16 min 567

D Clearance to adjacent cabinetry front panel min 1/16 min 2

E Clearance between top of custom panel

and upper cabinetry panel min 1/8 min 3

F Clearance between bottom of custom panel

and lower cabinetry panel min 1/16 min 2

* Ovens and companion products can be placed directly on top of the warming drawer.

NOTE: The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.

PLAN

PO*

Panel above product

Upper shelf

Lower shelf

Panel below product

PROFILE

Custom panel

This installation is suitable for Minimal, Contemporary & Professional Warming drawers. A fixed

shelf must be installed above the warming drawer.

FRONT

Upper shelf

Lower shelf

Warming drawer

Panel above product

Panel below product

PROFILE

Panel above product

Warming drawer

Panel below product

This installation combines 30" Warming Drawer with 30" Fisher & Paykel wall oven. The

warming drawer can support the weight of the oven sitting directly on top.

COMBINED WITH SINGLE OVEN

PROFILE

FRONT

Panel above product

Panel below product

Upper shelf

Lower shelf

Wall oven

Warming drawer

Panel above product

Wall oven

Panel below product

Warming drawer

STANDALONE INSTALLATION

INSTALLATION OPTIONS

This installation combines 24' or 30" Warming Drawer with 24" or 30" Fisher & Paykel

companion product. The warming drawer can fully support the weight of the companion

product sitting directly on top.

INSTALLATION OPTIONS

COMBINED WITH COMPANION PRODUCT

Panel above product

Panel below product

Upper shelf

Lower shelf

Coffee maker,

Microwave oven or

Steam oven

Warming drawer

Panel above product

Coffee maker,

Microwave oven or

Steam oven

Panel below product

Warming drawer

PROFILE

FRONT

This installation combines 30" Warming Drawer with a 30" Fisher & Paykel double oven. The

warming drawer can fully support the weight of the double oven sitting directly on top.

COMBINED WITH DOUBLE OVEN

FRONT

PROFILE

Double oven

Warming Drawer

Panel below product

Panel above product

This combination is suitable for 30" Warming Drawers. A shelf is required above the oven to

support the 30" companion product. Ensure the bottom shelf can fully support the weight of

all appliances.

TRIPLE STACK COMBINATION

Panel above product

Coffee maker,

Microwave oven or

Steam oven

Wall oven

Panel below product

Warming drawer

PROFILE

Panel above product

Panel below product

Upper shelf

Middle shelf

Lower shelf

Coffee maker,

Microwave oven or

Steam oven

Warming drawer

Wall oven

FRONT

INSTALLATION OPTIONS ATTACH THE HANDLE

To attach the handle, refer to the installation guide included with the Handle kit (purchased

separately).

Contemporary style handle

Professional style handle

INSTALLING THE DRAWER

Use the supplied spacer to

position the side brackets (2x)

to correct depth.

Secure the side brackets to the

side panels of the cabinetry

with T20 wood screws (6x).

Ensure the cabinetry is square

and base is level.

Secure the bracket cover and

chassis flange to the side

brackets with T20 machine

screws (6x).

Route the power cord into the

back of the cavity and plug it

into the socket.

Slide the drawer carefully inside

the cabinetry.

5Remove the backing of

adhesive tapes (9x) on the

door frame.

side bracket

bracket cover

spacer

side bracket

INSTALLING THE DRAWER

Open the drawer fully, and remove

the T20 machine screws (4x) from

both sides of the door frame.

Slide the door frame and custom

panel up and off the drawer.

Drill pilot holes (6x) into the

custom panel through the screw

holes in the door frame.

Be careful not to drill through to

the front of the panel.

Secure the custom panel to the

door frame with T20 wood screws

(6x).

Slide the door frame back onto

the drawer and align the custom

panel vertically with surrounding

cabinetry.

Secure the door frame in place

with T20 machine screws (4x).

Align the custom panel carefully

with the cabinetry.

Ensure the custom panel is

correctly aligned and centered

before fixing to the tape as this

can only be done once.

Use shims (not supplied) to ensure

gaps are accurate.

shims

ADJUSTING THE DEPTH ADJUSTING THE HEIGHT

Open the drawer fully.

Using a hex key, turn the adjustment

screw to move the front panel forward.

Turn clockwise to move backwards or

counterclockwise to move forwards.

2The front panel depth is adjustable

within 4mm.

The depth of the front panel of the warming drawer can be adjusted to align with the

surrounding cabinetry.

Open the drawer fully, and slightly

loosen the T20 screws.

Adjust to the required height and then

re-tighten the screws. The height is

adjustable within 2mm.

Close the drawer and check the

alignment. Adjust again if necessary.

The front panel of the warming drawer can be adjusted vertically to align with the surrounding

cabinetry.

max 2mm

F the warming drawer is level and securely fitted to the cabinetry.

F any internal packaging has been removed from the drawer.

F the isolating switch is accessible to the customer.

F the bottom shelf can fully support the total weight of the combined appliances.

F Open the drawer.

F Press the

FP WARMER DRAWER INTERFACE LOGIC_V1

PRODUCT OFF

THE THREE TEMPERATURE BUTTONS WORK AS A UNIT

ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,

THE OTHER TWO BUTTONS SHOW WHITE

THE TWO TIMER BUTTONS WORK AS A UNIT

ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,

THE OTHER BUTTON SHOWS WHITE

ICE AND WATER INTERFACE COMPONENTS

All bezels capable of glowing white and red

except fot the on /o bezel which only needs

to glow red.

Component Layout As Shown.

USER PRESSES ON/OFF BUTTON

ALL OTHER BEZELS GLOW WHITE EXCEPT

TEMPERATURE SETTING WHICH IS PRESET TO

MEDIUM AND GLOWS RED (PRODUCT STARTS

HEATING TO THE MEDIUM TEMPERATURE)

ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED

AGAIN SHUTTING THE PRODUCT OFF.

WHEN THE TIMER BUTTON IS PRESSED THE

PRODUCT IS SET TO RUN FOR THE ALLOWED

TIME.

WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS

OFF.

button to turn the warming drawer on.

F Shut the drawer.

F After 5-10 minutes, open the drawer to ensure heating has started.

F Press the

FP WARMER DRAWER INTERFACE LOGIC_V1

PRODUCT OFF

THE THREE TEMPERATURE BUTTONS WORK AS A UNIT

ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,

THE OTHER TWO BUTTONS SHOW WHITE

THE TWO TIMER BUTTONS WORK AS A UNIT

ONLY ONE CAN BE SELECTED AND SHOW RED AT A TIME,

THE OTHER BUTTON SHOWS WHITE

ICE AND WATER INTERFACE COMPONENTS

All bezels capable of glowing white and red

except fot the on /o bezel which only needs

to glow red.

Component Layout As Shown.

USER PRESSES ON/OFF BUTTON

ALL OTHER BEZELS GLOW WHITE EXCEPT

TEMPERATURE SETTING WHICH IS PRESET TO

MEDIUM AND GLOWS RED (PRODUCT STARTS

HEATING TO THE MEDIUM TEMPERATURE)

ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED

AGAIN SHUTTING THE PRODUCT OFF.

WHEN THE TIMER BUTTON IS PRESSED THE

PRODUCT IS SET TO RUN FOR THE ALLOWED

TIME.

WHEN THIS TIME RUNS OUT THE PRODUCT SHUTS

OFF.

button to turn the warming drawer off and shut the drawer.

Complete and keep for safe reference:

Model

Serial No.

Purchase Date

Purchaser

Dealer Address

Installer’s Name

Installer’s Signature

Installation Company

Installation Date

INSTALLER CHECKLIST

IMPORTANT!

Read all installation instructions in this manual to see if the unit has been correctly installed.

Ensure that installation has been completed correctly before use.

Ensure that: Test operation:

592266B 04.21

FISHERPAYKEL.COM

The models shown in this guide may not be available in all markets

and are subject to change at any time.

The product specifications in this guide apply to the specific products and

models described at the date of issue. Under our policy of continuous product

improvement, these specifications may change at any time.

For current details about model and specification availability in your country,

please go to our website or contact your local Fisher&Paykel dealer.

Fisher & Paykel W30SDEI Installation guide

Fisher & Paykel W30SDEI Installation guide

Fisher & Paykel W30SDEI Installation guide

Related papers

Other documents