Reelcraft 600873 User manual

600873
Reelcraft
Brand
Reelcraft
Model
600873
Category
Motorcycle Accessories
Type
User manual

Reelcraft 600873 is a Forward/Reverse Variable Speed Control, specifically designed for Universal Motors with a Motor Tag Current Rating of no larger than 10 Amps. It contains an internal rectifier, eliminating the need for internal motor rectifier wires. The control features a momentary pushbutton for slow (on)-off operation and a Forward/Reverse rocker switch for fast wind and unwind. Installation requires mounting the control standing up and making wire connections in a separate electrical box.

Reelcraft 600873 is a Forward/Reverse Variable Speed Control, specifically designed for Universal Motors with a Motor Tag Current Rating of no larger than 10 Amps. It contains an internal rectifier, eliminating the need for internal motor rectifier wires. The control features a momentary pushbutton for slow (on)-off operation and a Forward/Reverse rocker switch for fast wind and unwind. Installation requires mounting the control standing up and making wire connections in a separate electrical box.

Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form # TB0028 Rev: 4/2022
Tech Bulletin
600873 Speed Control
Installation Instructions
600873 Speed Control Install Instructions Revised: 2/22
REELCRAFT (800) 444-3134
Slow Fast
Reel
Motor
NOTE: If the motor direction is not correct,
swap the motor wires with the speed
control's two blue wires.
Motor Wire #5
Black (hot leg)
White (neutral)
Input
115 Volt AC
Blue to motor wire Motor Wire #6
Motor wires #1, #2, #3, #4 are not
used when using the Speed Control.
The rectification function is integrated
in the speed control and these four
motor wires are not required.
There is no voltage or current in these
wires when the motor, or speed control,
is operating. You may insulate these
with electrical tape and secure these
wires so they do not hinder the reel
drive mechanism.
Black (hot leg)
White (hot leg)
Input
230 Volt AC
Output 115 Volts DC
Forward/Reverse
Rocker Switch
Output 230 Volts DC
to Motor
1/2 " Conduit
Connector
Speed Control
Blue to motor wire
(On)-Off Momentary
Pushbutton
Warranty:
Circuit Protection - The installer must provide the 12 AWG, 2 conductor feed line and it must be on it's own
circuit, protected by a 15 Amp circuit breaker in the electrical service panel. Do not use a ground fault breaker for
the motor controller circuit protection.
Make the wire connections in your own electrical box - Do not
open the controller. There is no room in the controller to make your
wire connections. Use aluminum conduit between the controller
and your electrical box.
Wind
Unwind
The control is warranted, by the manufacturer, to be defect free from faulty materials or workmanship. If a defect occurs within the 1 Year Warranty
period, the control must be shipped to Qualitech for "cause of fail" analysis. If it is determined 1) the control was not wired per these wiring
instructions, 2) the control was opened or altered or, 3) the control was subject to an application it was not designed for, then the manufacturer is
not responsible for liability situations or warranty of the product. After the 1 Year Warranty, the customer may send the unit in for a repair quote.
Application:
The 600873 is a Forward/Reverse Variable Speed Control and is specifically designed for the 115 Volt or the 230 Volt
Universal Motors (Rectified DC Motors) with a Motor Tag Current Rating of no larger than 10 Amps. The control
contains an internal rectifier, therefore the internal motor rectifier wires are not used. See wiring instructions.
Wiring Instructions
Mounting: Screw holes in the enclosure flange or drill your own holes in the flange. Mount the control
standing up; not flat on it's back.
Before wiring the control, assure the direction rocker switch is in
the "center off" position.
New Application Restriction:
The control cannot be used for motor wires longer than 150 feet. The added inductance caused by the long motor
wires is beyond the specs of this control. If you require a control with longer than 150 feet of motor wires, you must
contact Reelcraft to acquire a "special application" control.
Do not connect the motor's green
ground wire to any of the control's
wires.
  • Page 1 1

Reelcraft 600873 User manual

600873
Reelcraft
Brand
Reelcraft
Model
600873
Category
Motorcycle Accessories
Type
User manual

Reelcraft 600873 is a Forward/Reverse Variable Speed Control, specifically designed for Universal Motors with a Motor Tag Current Rating of no larger than 10 Amps. It contains an internal rectifier, eliminating the need for internal motor rectifier wires. The control features a momentary pushbutton for slow (on)-off operation and a Forward/Reverse rocker switch for fast wind and unwind. Installation requires mounting the control standing up and making wire connections in a separate electrical box.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents