LD display Operating Software
Installation manual
R5976787/02
02/0
5/2006
Barco nv Media
Noordlaan 5, B-8520 Kuurne
Phone: +
32 56.36.89.70
Fax: +32 56.36.83.86
E-mail: sales.media@barco.com
Visit us at
the web: www.barco.com
Printed in Belgium
Changes
Barco provides this manual ’as is’ without warranty of any kind, either expressed or implied, including but not
limited to the implied warranties or merchantability and fitness for a particular p urp ose. B a rc o may make im-
provements and/or changes to the product(s) and/or the program(s) described in this publication at any time
without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made
to the information in this publication; these changes are incorporated in new editions of this publication.
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise
be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of gu
arantee.
On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as
well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software
on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of
complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period.
If this measure proves to b e impossible or unsuccessful, the purchaser can demand a reduction in the purchase
price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided
by Barco, being a component of the system or independent service, will be deemed invalid provided the damage
is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross
negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods
are handled incorrectly, in particular if the systems are commissioned operated incorrectly or if, a fter the trans-
fer of risks, the goods are subject to influences not agreed upon in th
e co ntract, all guara nt ee claims of th e
purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are at-
tributed to programs or special electronic circuitry provided by the p urchaser, e.g. interfaces. Normal wear as
well as normal maintenance are not subject to the guarantee provi
ded by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in the this manual
must be complied with by the customer.
Trad emarks
Brand and product names mentioned in this manual may be tra
demarks, registered trademarks or copyrights
of their respective holders. All brand and product names mentioned in this manual serve as comments or
examples and are not to be understood as advertising for the products or their manufactures.
Table of contents
TABLE OF CONTENTS
1. Overview ........................................................................................... 3
1.1 Before starting................................................................................................. 3
1.2 PC requirements .............................................................................................. 3
1.3 Installation Overview.......................................................................................... 4
2. Installation ofthe software .................................................................... 5
2.1 Installation of LD display software........................................................................... 5
2.2 Installation of XLite Toolset................................................................................... 6
2.3 Uninstalling LD display software ............................................................................ 8
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
1
Table of contents
2 R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
1. Overview
1. OVERVIEW
Overview
• Before starting
• PC requirements
• Installation Overview
1.1 Before starting
Overview
This guide is intended for system adm inistrators. It assumes you are familiar with the Windows operating
system at your site and with standard system administration tasks.
The CD-ROM in your package contains all the product data for the LD display software, including a Win-
dows-based installation program. You can install the software from the CD-ROM.
1.2 PC requirements
PC must contain one free serial port.
DPI settings must be set to normal.
Minimum hardware requirements
• Pentium II 400 MHz or higher
• Memory : 256 MB Ram
• One free serial port
Operating system
• Windows 2000
•WindowsXP
DPI setting
To avoid the missing of buttons and/of the system uses diffe rent fonts, set the DPI setting to the normal
size (96 dpi).
To set the dpi setting to the normal size :
1. Open the Windows display settings via Start → Settings → Display or via right click on the d es k to p
and selecting Properties.
2. Select Settings.
3. Click on Advanced.
4. Click the General tab.
5. In Display, select Small font (96 dpi).
6. Close the display settings window.
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
3
1. Overview
1.3 Installation Overview
Installation steps
1. Installation info gathering
2. Inst allation of LD display softwa re
3. Installation of XLite Toolset
4
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
2. Installation of the software
2. INSTALLATION OF THE SOFTWARE
2.1 Installation of LD display software
To install
1. Insert the CD-ROM in the CD-ROM drive.
2. Is the AutoPlay active on your PC.
If yes, continue with step 6.
If no, from within the Windows environment go to the Start Menu. Choose Run... from the menu and
proceed with the next steps.
3. Open windows explorer.
4. Select the CD-ROM Drive.
5. Double click ‘setup.exe’ file.
The installation wizard will be display ed .
6. Click Next on the installation wizard startup page. (image 2-1)
The license window opens (License agreement). (image 2-2)
Read this te xt carefully.
7. Do you agree with the license text ?
If yes, Click Yes to accept the agreement and to continue to the next step.
The customer information window opens. (image 2-3)
8. Fill out the necessary information and click Next.
The destinatio n window opens. A proposed path is filled out. (image 2-4)
9. If you agree with the proposed path, click Next.
Otherwise click Browse and select the desired path.
The program folder selection window opens. (image 2-5)
10.If you accept the proposed folder, click Next.
Otherwise select a folder or enter a new name.
The LD display s oftwa re will be installed.
When the installation of the LD display software is finished, the wizard starts with the installation of
XLite Toolset.
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
5
2. Installation of the software
Image 2-1
Installation wizard start up
Image 2-2
License agree ment
Image 2-3
Customer information
Image 2-4
Destination window
Image 2-5
Program folder
2.2 Installation of XLite Toolset
To install
1. To start up the installation click on Next.(image2-6)
6 R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
2. Installation of the software
2. Read the license agreement and if agree, click on Next.
3. Accept the destination path or browse to a new path and click Next.
4. Set up choice. For new installation select ’Typical’.
With ’Typical’, everything necessary to run the program will be installed (Tomcat webserver, Java envi-
ronment variables and plug ins for the applets).
With ’Custom’ you have the choice to install only the Xlite part or only the Java part.
5. Select Next to install.
The XLite Toolset installation wizard returns to the LD display software wizard.
6. Click Finish to com plete the installation.
Image 2 -6
XLite Toolset install shield wizard
Check
Some settings of the PC must be checked before launching the software:
1. Check if the Java Virtual m achine (VM) is enabled on the PC.
2. Open your Internet Explorer.
Select Tools → Internet Options → Temporary Internet Files → Settings.
3. Check ’Every visit to the page’ and press OK. (image 2-7)
Image 2 -7
Internet options Settings
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006 7
2. Installation of the software
2.3 Uninstalling L D display software
How to uninstall
1. Open the Control Panel of your windows (Start → Settings → Control Panel).
2. Select Solaris LD from the list and click on the Cha nge/Remove button.
The uninstall procedure for LD display software will start.
3. The uninstall wizard asks for c onfirmation.
4. Click OK to remove completely.
5. Do you want to remove the data files too? Data files are the user files, preset files, configuration, etc.
If ye s, click on Yes. Every thing will be deleted.
If no, click on No. LD display software will be able to work on the same configuration when reinstalled
later.
8
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
Revision Sheet
To:
Barco nv Media/Documentation
Noordlaan 5, B-8520 Kuurne
Phone: +32 56.36.89.70, Fax: +32 56.36.83.86
From:
Date:
Please correct the following points in this documentation (R5976787/02):
page
wrong
correct
R5976787 LD DISPLAY OPERATING SOFTWARE 02/05/2006
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
Barco LD140-10 Installation guide
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Barco LD150-10 User guide
-
-
-
-
-
Barco R9851560 User manual
-
-
-
-