Mode AVIC F10 BT Owner's manual

INSTALLATION MANUAL

MANUEL D’INSTALLATION

NAVIGATION AV SYSTEM

SYSTEME DE NAVIGATION AV

AVIC-F10BT

English NederlandsItalianoFrançaisDeutschEspañol

IMPORTANT INFORMATION

ABOUT YOUR NEW NAVIGATION SYSTEM

AND THIS MANUAL 3

IMPORTANT SAFEGUARDS

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING YOUR

NAVIGATION SYSTEM AND RETAIN THEM

FOR FUTURE REFERENCE 4

Connecting the System

Precautions before connecting the

system 5

Before installing this product 6

To prevent damage 6

– Notice for the blue lead 6

– Notice for the blue/white lead 7

Parts supplied 7

Connecting the system 8

Connecting the power cord (1) 10

Connecting the power cord (2) 12

When connecting to separately sold power

amp 14

When connecting a rear view camera 16

When connecting the rear display 17

– When using a rear display connected to

rear video output 17

When connecting the external video

component 17

– Using “AV1 Input” (AV1) 17

– Using “AV2 Input” (AV2) 18

When connecting the external unit featuring

video source 19

Installation

Precautions before installation 20

To guard against electromagnetic

interference 20

Before installing 20

Installing this navigation system 21

– Installation notes 21

– Parts supplied 22

– Before installing this navigation

unit 23

– Installation with the holder and side

bracket 23

– Installation using the screw holes on

the side of the navigation unit 24

Installing the GPS aerial 25

– Installation notes 25

– Parts supplied 25

– When installing the aerial inside the

vehicle (on the dashboard or rear

shelf) 26

Installing the microphone 27

– Parts supplied 27

– Mounting on the sun visor 27

– Installation on the steering column 28

– Adjusting the microphone angle 29

Contents

Engb

2

ABOUT YOUR NEW

NAVIGATION SYSTEM AND

THIS MANUAL

! The navigation features of this product

(and rear view camera option if purchased)

are intended solely to aid you in the opera-

tion of your vehicle. It is not a substitute for

your attentiveness, judgement and care

when driving.

! Never use this navigation system to route

to hospitals, police stations, or similar facil-

ities in an emergency. Please call the ap-

propriate emergency number.

! Do not operate this navigation system (or

the rear view camera option if purchased) if

doing so in any way will divert your atten-

tion from the safe operation of your vehicle.

Traffic restrictions and advisories currently

in force should always take precedence

over guidance given by this product. Al-

ways obey current traffic restrictions, even

if this product provides contrary advice.

! This manual explains how to install this na-

vigation system in your vehicle. Operation

of this navigation system is explained in

the separate manuals for the navigation

system.

! Do not install this product where it may (i)

obstruct the driver’s vision, (ii) impair the

performance of any of the vehicle’s operat-

ing systems of safety features, including

airbags, hazard lamp buttons or (iii) impair

the driver’s ability to safely operate the vehi-

cle. In some cases, it may not be possible

to install this product because of the vehi-

cle type or the shape of the vehicle inter-

ior.

IMPORTANT INFORMATION

Engb

3

English

Section

01

WARNING

Pioneer does not recommend that you install

your navigation system yourself. We recom-

mend that only authorised Pioneer service

personnel, who have special training and ex-

perience in mobile electronics, set up and in-

stall this product. NEVER SERVICE THIS

PRODUCT YOURSELF. Installing or servi-

cing this product and its connecting cables

may expose you to the risk of electric shock

or other hazards, and can cause damage to

the navigation system that is not covered by

warranty.

PLEASE READ ALL OF THESE

INSTRUCTIONS REGARDING

YOUR NAVIGATION SYSTEM

AND RETAIN THEM FOR

FUTURE REFERENCE

1 Read this manual fully and carefully before in-

stalling your navigation system.

2 Keep this manual handy for future reference.

3 Pay close attention to all warnings in this

manual and follow the instructions carefully.

4 This navigation system may in certain circum-

stances display erroneous information regard-

ing the position of your vehicle, the distance

of objects shown on the screen, and compass

directions. In addition, the system has certain

limitations, including the inability to identify

one-way streets, temporar y traffic restrictions

and potentially unsafe driving areas. Please

exercise your own judgement in the light of

actual driving conditions.

5 As with any accessory in your vehicle’s inter-

ior, the navigation system should not divert

your attention from the safe operation of your

vehicle. If you experience difficulty in operat-

ing the system or reading the display, please

make adjustments while safely parked.

6 Please remember to wear your seat belt at all

times while operating your vehicle. If you are

ever in an accident, your injuries can be con-

siderably more severe if your seat belt is not

properly fastened.

7 Certain government laws may prohibit or re-

strict the placement and use of this system in

your vehicle. Please comply with all applicable

laws and regulations regarding the use, instal-

lation and operation of your navigation sys-

tem.

IMPORTANT SAFEGUARDS

Engb

4

Section

02

Precautions before

connecting the system

CAUTION

! If you decide to perform the installation

yourself, and have special training and ex-

perience in the mobile electronics instal-

lations, please carefully follow all of the

steps in the installation manual.

! Secure all wiring with cable clamps or

electrical tape. Do not allow any bare wir-

ing to remain exposed.

! Do not directly connect the yellow lead of

this product to the vehicle battery. If the

lead is directly connected to the battery,

engine vibration may eventually cause

the insulation to fail at the point where

the wire passes from the passenger com-

partment into the engine compartment. If

the yellow lead’s insulation tears as a re-

sult of contact with metal parts, short-cir-

cuiting can occur, resulting in

considerable danger.

! It is extremely dangerous to allow the

cables to become wound around the steer-

ing column or gearstick. Be sure to install

this product, its cables, and wiring away

in such a way that they will not obstruct

or hinder driving.

! Make sure that the cables and wires are

routed and secured so they will not inter-

fere with or become caught in any of the

vehicle’s moving parts, especially the

steering wheel, gearstick, handbrake, slid-

ing seat tracks, doors, or any of the vehi-

cle’s controls.

! Do not route wires where they will be ex-

posed to high temperatures. If the insula-

tion heats up, wires may become

damaged, resulting in a short circuit or

malfunction and permanent damage to

the product.

! Do not cut the GPS aerial cable to shorten

it or use an extension to make it longer.

Altering the aerial cable could result in a

short circuit or malfunction.

! Do not shorten any leads. If you do, the

protection circuit (fuse holder, fuse resis-

tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-

ducts by cutting the insulation of the

power supply lead of the navigation sys-

tem and tapping into the lead. The current

capacity of the lead will be exceeded,

causing overheating.

! The black lead is earth. Please earth this

lead separately from the earth of high-cur-

rent products such as power amps. Do not

earth more than one product together

with the earth from another product. For

example, you must separately earth any

amp unit away from the earth of this navi-

gation system. Connecting earths to-

gether can cause a fire and/or damage the

products if their earths became

detached.

Connecting the System

Engb

5

English

Section

03

Before installing this product

! This product is for vehicles with a 12-volt

battery and negative earthing. Check the

battery voltage of your vehicle before instal-

lation.

! To avoid shorts in the electrical system, be

sure to disconnect the (–) battery cable be-

fore beginning installation.

To prevent damage

WARNING

! When replacing the fuse, be sure to only

use a fuse of the rating prescribed on this

product.

! When disconnecting a connector, pull the

connector itself. Do not pull the lead, as

you may pull it out of the connector.

! This product cannot be installed in a vehi-

cle without ACC (accessory) position on

the ignition switch.

A

C

O

N

S

T

A

R

T

O

F

O

N

S

T

A

R

T

O

F

ACC position No ACC position

! To avoid short-circuiting, cover the discon-

nected lead with insulating tape. It is espe-

cially important to insulate all unused

speaker leads, which if left uncovered may

cause a short circuit.

! Attach the connectors of the same colour

to the corresponding coloured port, i.e.,

blue connector to the blue port, black to

black, etc.

! Refer to the owner’s manual for details on

connecting the power amp and other units,

then make connections accordingly.

! Since a unique BPTL circuit is employed,

do not directly earth the * side of the

speaker lead or connect the * sides of the

speaker leads together. Be sure to connect

the * side of the speaker lead to the *

side of the speaker lead on this navigation

system.

! If the RCA pin jack on this product will not

be used, do not remove the caps attached

to the end of the connector.

! Never connect speakers with an output rat-

ing of less than 50 W channel or impe-

dance outside of the 4 ohms to 8 ohms

specifications to your navigation system.

Connecting speakers with output and/or

impedance values other than those noted

here may result in the speakers catching

fire, emitting smoke, or becoming da-

maged.

Notice for the blue lead

! A signal is output through the blue lead to

control the aerial of your vehicle. The tim-

ing varies depending on the setting. (For

more detailed information on changing

[ANT CTRL] mode, refer to “Operation Man-

ual”.)

! When [ANT CTRL] mode is set to [Radio],

the vehicle ’s aerial can be stowed or turned

off by following the instructions below.

— Change the source from radio (MW/LW

or FM) to another source.

— Turn the source off

— Turn off the ignition switch (ACC OFF)

! If [ANT CTRL] mode is set to [Power], the

vehicle’s aerial can be stowed or turned off

only when the ignition switch is turned off

(ACC OFF).

Connecting the System

Engb

6

Section

03

! Do not connect this lead to the system con-

trol terminal of external power amps.

! Be sure not to use this lead as the power

supply lead for the auto-aerial or aerial

booster. Such connection could cause ex-

cessive current drain and malfunction.

Notice for the blue/white lead

! When the ignition switch is turned on (ACC

ON), a control signal is output through the

blue/white lead. Connect to an external

power amp’s system remote control term-

inal (max. 300 mA 12 V DC). The control sig-

nal is output through the blue/white lead,

even if the audio source is switched off.

! Do not connect this lead to the auto-aerial

relay control terminal or the aerial booster

power control terminal.

! Be sure not to use this lead as the power

supply lead for the external power amps.

Such connection could cause excessive

current drain and malfunction.

Parts supplied

The navigation unit Power cord

RDS-TMC tuner USB connector

Connector Extension lead

(for reverse signal)

Extension lead

(for speed signal)

GPS aerial

RCA connector Microphone

Connecting the System

Engb

7

English

Section

03

Connecting the system

WIRED REMOTE INPUT

Please see the Instruction

Manual for the Wired Remote

Control Adapters (sold separately).

The navigation unit

USB connector

Connect either the interface

cable for iPod or an

appropriate USB storage

device.

*1

— When connecting your iPod, both connections are necessary.

— It is necessary to set [AV1 Input] in [AV Settings] to [iPod] when

connecting the iPod. (For details, refer to “Operation Manual”.)

*

1

Green

5 m

Aerial

jack

RDS-TMC tuner

Vehicle

aerial

2 m

1 m

30 cm

Connecting the System

Engb

8

Section

03

Dock

connector

port

WARNING

· To avoid the risk of accident and the potential violation of applicable laws, this

product should never be used while the vehicle is being driven except for

navigation purposes. And, also Rear Displays should not be in a location where it

is a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by

persons other than the driver may be illegal. Where such regulations apply they

must be obeyed and this product´s video source should not be used.

USB Interface Cable for iPod

(CD-IU50V) (sold separately)

iPod with

Dock Connector*2

*2

For details concerning

operations and compatibility ,

refer to the operation manual.

4 m

Microphone

GPS aerial

Connecting the System

Engb

9

English

Section

03

Connecting the power cord (1)

ISO connector

*1

*2

*4

*3

*5

Speaker leads

White: Front left 

White/black: Front left 

Grey: Front right 

Grey/black: Front right 

Green: Rear left  or Subwoofer  (*9)

Green/black: Rear left  or Subwoofer  (*9)

Violet: Rear right  or Subwoofer  (*9)

Violet/black: Rear right  or Subwoofer  (*9)

Depending on the kind of vehicle, the function

of *3 and *5 may be different. In this case, be

sure to connect *2 to *5 and *4 to *3.

Connect leads of the

same colour to each other.

Cap (*1)

When not using this terminal,

do not remove the cap.

Yellow (*3)

Back-up

(or accessory)

Red (*5)

Accessory

(or back-up)

Yellow (*2)

To terminal always supplied

with power regardless of

ignition switch position.

Red (*4)

To electric terminal controlled by

ignition switch (12 V DC) ON/OFF.

Orange/white

To lighting switch terminal.

Black (earth)

To vehicle (metal) body.

In some vehicles, the ISO connector may be divided

into two. In this case, be sure to connect to both

connectors.

Yellow/black

If the vehicle can send a mute signal to this terminal,

the mute function can be activated on this navigation

system when the terminal is connected to *8.

Note

Notes

· When a subwoofer (*9) is connected to this

navigation system instead of a rear speaker, change

the rear output setting in the Initial Setting. (Refer to

“Operation Manual”.) The subwoofer output of this

navigation system is monaural.

· When using a subwoofer of 70 W (2 Ω), be sure to

connect with violet and violet/black leads of this

navigation system. Do not connect anything with

green and green/black leads.

Connecting the System

Engb

10

Section

03

The navigation unit

Blue (*6)

Blue (*7)

To auto-aerial relay control

terminal (max. 300 mA 12 V DC).

The pin position of the ISO connector will differ

depending on the type of vehicle. Connect *6 and

*7 when Pin 5 is an aerial control type. In other

types of vehicle, never connect *6 and *7.

(*8)

Fuse (10 A)

Yellow/black

If you use an equipment with mute function, connect that equipment to the

Audio Mute lead. If not, keep this lead free of any connections.

Power cord

Audio source will be set to mute or attenuate, while the following sounds

will not be muted or attenuated. For details, see “Operation Manual”.

— voice guidance of the navigation

— incoming ringtone and incoming voice of the mobile phone that is

connected to this navigation system via Bluetooth wireless technology

26 cm

Note

The aerial will automatically retract, yet the timing varies depending on

the setting.

RCA connector

Connecting the System

Engb

11

English

Section

03

Connecting the power cord (2)

IMPROPER CONNECTION MAY RESULT IN SERIOUS DAMAGE

OR INJURY INCLUDING ELECTRICAL SHOCK, AND

INTERFERENCE WITH THE OPERATION OF THE VEHICLE´S

ANTILOCK BRAKING SYSTEM, AUTOMATIC GEARBOX AND

SPEEDOMETER INDICATION.

Pink (CAR SPEED SIGNAL INPUT)

The mobile navigation system is connected here to detect the distance the

vehicle travels. Always connect the vehicle´s speed detection circuit. Failure

to make this connection will increase errors in the location display.

LIGHT GREEN LEAD AT POWER CONNECTOR IS

DESIGNED TO DETECT PARKED STATUS AND MUST

BE CONNECTED TO THE POWER SUPPLY SIDE OF THE

HANDBRAKE SWITCH. IMPROPER CONNECTION OR

USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW

AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

Light green

Used to detect the ON/OFF status of the handbrake. This lead must be

connected to the power supply side of the handbrake switch.

If this connection is made incorrectly or omitted, certain functions

of your navigation system will be unusable.

The position of the speed detection circuit and the position of the

handbrake switch vary depending on the vehicle model. For details,

consult your authorised Pioneer dealer or an installation professional.

Speed detection circuit lead

Connection method

Power supply side

Earth side

Handbrake switch

3 m

Pass the extension

cord and the lead for

the speed detection

circuit through this

hole.

Clamp firmly

with needle-

nosed pliers.

Connection method

Clamp the handbrake switch

power supply side lead.

Clamp firmly with needle-nosed

pliers.

Close the cover.

Vehicle injection

computer

Connector

WARNING

CAUTION

Note

WARNING

It is strongly suggested that the speed pulse wire be connected for

accuracy of navigation and better performance.

Connecting the System

Engb

12

Section

03

Power cord

Violet/white (REVERSE GEAR SIGNAL INPUT)

This is connected so that the navigation system can detect

whether the vehicle is moving forwards or backwards.

Connect the violet/white lead to the lead whose voltage

changes when the reverse gear is engaged. Unless

connected, the sensor may not detect your vehicle

travelling forward/backward properly, and thus the position

of your vehicle detected by the sensor may be misaligned

from the actual position.

When you use a rear view camera, please make

sure to connect this lead. Otherwise you cannot

switch to rear view camera picture.

Be sure to use only the supplied extension lead. Use of another

lead could cause fire, smoke and/or damage this navigation

system.

Connection method

Check the position of your

vehicle´s reversing lamp (the one

that lights up when the gearstick is

in reverse [R]) and find the

reversing lamp lead in the boot.

Extension lead

(for reverse signal)

Extension lead

(for speed signal)

The navigation unit

5 m

Fuse resistor

Reversing

lamp lead

Clamp the reversing

lamp lead.

Clamp firmly with

needle-nosed

pliers.

Note

CAUTION

Connecting the System

Engb

13

English

Section

03

When connecting to separately sold power amp

The navigation unit

Front output

(FRONT OUTPUT)

Rear output

(REAR OUTPUT)

25 cm

30 cm

RCA connector

Subwoofer output

(SUBWOOFER OUTPUT)

To system control terminal of the power amp

(max. 300 mA 12 V DC).

Blue/white

Connecting the System

Engb

14

Section

03

Power amp

(sold separately)

Power amp

(sold separately)

Power amp

(sold separately)

























RCA cables

(sold separately)

Front speaker

Rear speaker

Subwoofer

Front speaker

Rear speaker

Subwoofer

Left Right

System remote control

You can change the RCA output of the subwoofer depending on your subwoofer

system. (Refer to “Operation Manual”.)

Note

Connecting the System

Engb

15

English

Section

03

When connecting a rear

view camera

When this product is used with a rear view

camera, it is possible to automatically switch

from the video to rear view image when the

gearstick is moved to REVERSE (R). Rear

View mode also allows you to check what is

behind you while driving.

WARNING

USE INPUT ONLY FOR REVERSE OR MIRROR

IMAGE REAR VIEW CAMERA. OTHER USE MAY

RESULT IN INJURY OR DAMAGE.

CAUTION

! The screen image may appear reversed.

! The rear view camera function is to use this

product as an aid to keep an eye on trailers, or

backing into a tight parking spot. Do not use

this function for entertainment purposes.

! The object in rear view may appear closer or

more distant than in reality.

! Please note that the edges of the rear view

camera images may differ slightly according

to whether full screen images are displayed

when backing, and whether the images are

used for checking the rear when the vehicle is

moving forward.

CAUTION

Be sure to use only the supplied extension

lead. Use of another lead could cause fire,

smoke and/or damage this navigation sys-

tem.

The navigation unit

Fuse resistor

20 cm

RCA cable

To video output

Brown

(REAR VIEW CAMERA IN)

(e.g. ND-BC2)

(sold separately)

Rear view camera

Extension lead (for reverse signal)

5 m

Violet/white

RCA connector

Power cord

For more details about the wiring, refer to Connecting

the power cord (2) on page 12.

Notes

! It is necessary to set [Back Camera]in

[System Settings]to[On] when connect-

ing the rear view camera. (For details, refer

to “Operation Manual”.)

! Connect to the rear view camera. Do not

connect to any other equipment.

Connecting the System

Engb

16

Section

03

When connecting the rear

display

The navigation unit

To video input

Rear display with

RCA input jacks

To audio inputs

Yellow

(REAR MONITOR

OUTPUT)

15 cm

RCA connector

Red, white

(REAR MONITOR

OUTPUT)

RCA cables

(sold separately)

When using a rear display

connected to rear video output

WARNING

NEVER install the rear display in a location

that enables the driver to watch the video

source while driving.

This navigation system’s rear video output is for

connection of a display to enable passengers in

the rear seats to watch the video source.

When connecting the

external video component

Using “AV1 Input” (AV1)

The navigation unit

RCA cables

(sold separately)

Yellow

Red, white

External

component

(sold separately)

video

To video output

To audio outputs

CD-RM10

(sold separately)

USB connector

2 m

! It is necessary to set [AV1 Input]in[AV

Settings]to[Video] when connecting the

external video component. (For details,

refer to “Operation Manual”.)

Connecting the System

Engb

17

English

Section

03

CAUTION

Be sure to use a CD-RM10 (sold separately) for

wiring. If you use other cables, there is a case

where wiring position differs, images and sounds

may be disturbed.

OK

G

V

R

L

G

R

V

L

L : Left audio (White)

R : Right audio (Red)

V : Video (Yellow)

G : Earth

Using “AV2 Input” (AV2)

To audio outputs

Yellow

(VIDEO INPUT)

20 cm

RCA connector

Red, white

(AUDIO INPUT)

RCA cables

(sold separately)

To video output

The navigation unit

External

component

(sold separately)

video

! It is necessary to set [AV2 Input]in[AV

Settings]to[Video] when connecting the

external video component. (For details,

refer to “Operation Manual”.)

Connecting the System

Engb

18

Section

03

When connecting the external

unit featuring video source

The navigation unit

Blue

Pioneer external unit

(sold separately)

20 cm

Yellow

(VIDEO INPUT)

To video output

Black

RCA connector

IP-BUS cable

(sold separately)

RCA cable

(sold separately)

To IP-BUS

output

! It is necessary to set [AV2 Input]in[AV

Settings]to[EXT] when connecting the ex-

ternal unit. (For details, refer to “Operation

Manual”.)

Connecting the System

Engb

19

English

Section

03

Precautions before

installation

CAUTION

! Never install this product in places where,

or in a manner that:

— It could injure the driver or passengers

if the vehicle stops suddenly.

— It may interfere with the driver’s opera-

tion of the vehicle, such as on the floor

in front of the driver’s seat, or close to

the steering wheel or gearstick.

! Make sure there is nothing behind the

dashboard or panelling when drilling

holes in them. Be careful not to damage

fuel lines, brake lines, electronic compo-

nents, communication wires or power

cables.

! When using screws, do not allow them to

come into contact with any electrical lead.

Vibration may damage wires or insulation,

leading to a short circuit or other damage

to the vehicle.

! To ensure proper installation, use the sup-

plied parts in the manner specified. If any

parts other than the supplied ones are

used, they may damage internal parts of

this product or they may work loose and

the product may become detached.

! It is extremely dangerous to allow the

cables to become wound around the steer-

ing column or gearstick. Be sure to install

this product, its cables, and wiring away

in such a way that they will not obstruct

or hinder driving.

! Make sure that leads cannot get caught in

a door or the sliding mechanism of a seat,

resulting in a short circuit.

! Please confirm the proper function of

your vehicle’s other equipment following

installation of the navigation system.

! Do not install this navigation system

where it may (i) obstruct the driver’s vi-

sion, (ii) impair the performance of any of

the vehicle’s operating systems or safety

features, including airbags, hazard lamp

buttons or (iii) impair the driver’s ability

to safely operate the vehicle.

! Install the navigation system between the

driver’s seat and front passenger seat so

that it will not be hit by the driver or pas-

senger if the vehicle stops quickly.

! Never install the navigation system in

front of or next to the place in the dash,

door, or pillar from which one of your vehi-

cle’s airbags would deploy. Please refer to

your vehicle’s owner’s manual for refer-

ence to the deployment area of the frontal

airbags.

! Do not install the navigation system in a

place where it will impair the performance

of any of the vehicle’s operating systems,

including airbags and headrests.

To guard against

electromagnetic interference

In order to prevent interference, set the follow-

ing items as far as possible from this naviga-

tion system, other cables or leads:

! FM, MW/LW aerial and its lead

! GPS aerial and its lead

In addition you should lay or route each aerial

lead as far as possible from other aerial leads.

Do not bind them together, lay or route them

together, or cross them. Such electromagnetic

noise will increase the potential for errors in

the location display.

Before installing

! Consult with your nearest dealer if installa-

tion requires the drilling of holes or other

modifications of the vehicle.

! Before making a final installation of this

product, temporarily connect the wiring to

confirm that the connections are correct

and the system works properly.

Installation

Engb

20

Section

04

Page is loading ...

Mode AVIC F10 BT Owner's manual

This manual is also suitable for

Mode AVIC F10 BT Owner's manual

in other languages

Related papers

Other documents