Costar CBC36 M Series Owner's manual

Dome

IR Bullet IR Bullet

Standard

12 13

- As the connecting method varies with the instruments, refer to the manual

supplied with the instrument.

- If necessary, you can connect the monitor to the REMOTE jack on the back of

your camera.

- Only connect the cable when the power is turned off.

- Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate

device.

VIDEO

1) Connection to Monitor

2) Connection to Power

Connect the adaptor to the power input connector

as shown in the figure right. The Standard voltage

for camera operation : DC 12V ± 10%, AC 24V±10%.

Power Input

Note

If you wish to use RS-485 connection, verify the proper polarity.

Connection

VIDEO

Dome Camera

3) Connection to RS-485

Using an RS485 connection you can control the OSD menu via the DVR

or system controller.

(1) Control via a PC

Using a RS-485 converter, It connects to RS-485 control cable outside camera

and serial cable

EX) SERIAL PORT OF THE PC(COM1) SERIAL CABLE RS-485

CONVERTER RS-485 CONTROL CABLE

(2) When controlling via a DVR or system controller connect the RS-485.

It connects the RS-485 control cable in the connection terminal of 485 control

boards which are connected with the DVR or System Controller.

→→

→

485 Control Board Connection Port RS-485 Control Port

(+) CONNECTION TERMINAL Brown (TRX+)

(- ) CONNECTION TERMINAL Blue (TRX-)

Item

Initial value

Camera ID

1

BAUD RATE

9600

UART MODE

8-NONE-1

RET PKT

ENABLE

ç RS-485 Communication parameters establishment initial value

Protocol : SAMSUNG

Baud Rate : 9600bps

Address : 1-255

When using a control system to operate the camera, please use the protocol:

SAMSUNG, PELCO-P or PELCO-D .

When use the RS485 control cable isolate the Drain wire.

-

Connection

NOTE

4) Connection to Alarm

Please see above RS485 connection picture. Normal Alarm output signal open,

and when motion detection operate, alarm output signal low to GND.

Dome Camera

20 21

- As the connecting method varies with the instruments, refer to the manual

supplied with the instrument.

- If necessary, you can connect the monitor to the REMOTE jack on the back of

your camera.

- Only connect the cable when the power is turned off.

- Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate

device.

1) Connection to Monitor

2) Connection to Power

Connect the adaptor to the power input connector as shown in the following figure .

The Standard voltage for camera operation : DC 12V ± 10%, AC 24V±10%.

Note

DC12V Only

Standard Camera Standard Camera

22 23

1. TO CONTROL THE CAMERA VIA COAXIAL COMMUNICATIONS

CAMERA

BNC jack

CAMERA

BNC jack

1) Connect the of the unit and of the A1 Camera directly.

- For proper data communication, the unit and A1 camera should be connected directly.

(If you connect a DVR or keyboard in the middle of the main unit and A1 camera, bidirectional

communication will not be established.)

2) Connect of the main unit to a monitor’s video input terminal.

3) Setting the protocol and address and baud rate, please the next page.

VIDEO IN VIDEO OUT

VIDEO OUT

2. TO CONTROL THE CAMERA USING RS-485 DEVICE VIA COAXIAL

COMMUNICATIONS

1) Connect the of the unit and of the A1 Camera directly.

- For proper data communication, the unit and A1 camera should be connected directly.

(If you connect a DVR or keyboard in the middle of the main unit and A1 camera, bidirectional

communication will not be established.)

2) Connect of the main unit to a monitor’s video input terminal.

3) Connect TX(+/-) of RS-485 device to RX(+/-) of the main unit.

(For a full duplex system, connect RX(+/-) of RS-485 device to TX (+/-) of main unit additionally.)

5) Using RS-485 device, you can control the camera menu.

VIDEO IN VIDEO OUT

VIDEO OUT

4) Setting the protocol and address and baud rate, please the next page.

3. Setting

Please check the menu of your camera, and setting like below and also to match the

menu of your camera. For more setting information please check SCX-RD100 manual.

CCVC ConnectionCCVC Connection

30

1) Metal Bracket Fixed

) Power Connect & Monitor Impedance

- using 4 screws, affix the metal bracket to wall or other surfaces.

2

Made sure which power supply that you

selected before you use.

- DC12V regulated power supply (DC12V only)

Dual power supply (AC24V/DC12V)

- To avoid fire or shock hazard, must use a

UL listed power supply.

- Set the monitor impedance switch to 75½.

Check the impedance switch when the screen turns blurred.

3

) Focus Adjustand Functions

- Loose the magnet-screw , and open the osd-cover , and use the extra cable to adjust

the focu

s and others functions . After finished, please tighten the osd-cover and

magnet-screw carefully .

Note

1. When you tighten the osd-cover, please make sure that you tighten well

and already adjust the function that you wish.

2. Before you connect the power , please check anywhere like that screw

and cable.

Camera Series

31

- As the connecting method varies with the instruments, refer to the manual

supplied with the instrument.

- If necessary, you can connect the monitor to the REMOTE jack on the back of

your camera.

- Only connect the cable when the power is turned off.

- Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate

device.

VIDEO

1) Connection to Monitor

2) Connection to Power

Connect the adaptor to the power input connector

as shown in the figure right. The Standard voltage

for camera operation : DC 12V ± 10%, AC 24V±10%.

Power Input

Note

If you wish to use RS-485 connection, verify the proper polarity.

2.8-12mm TDN Camera

Camera

Installation

Connection

5-50mm TDN Camera

VIDEO

IR Bullet Camera

Page is loading ...

Costar CBC36 M Series Owner's manual

This manual is also suitable for

Costar CBC36 M Series Owner's manual

Other documents