Rayburn XT Series Installation guide

Brand: Rayburn

Model: XT Series

Category: Fireplaces

Type: Installation guide

PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLING THIS APPLIANCE

For use in GB and IE

Installation

Instructions

400K (P/F)

04/14 EINS 512463[email protected]

DESN 512548 A

Remember, when replacing a part on this appliance, use only spare parts that you can be assured conform the safety and

performance specification that we require. Do not use reconditioned or copy parts that have not been clearly authorised

by AGA.

Contents

SECTION CONTENTS PAGE

CONSUMER PROTECTION 3

HEALTH & SAFETY 3

TECHNICAL DATA 4

SITE REQUIREMENTS INTRODUCTION 5

REGULATIONS 5

LOCATION 5

OIL PIPE LINE 6

OIL STORAGE 6

SINGLE AND TWO PIPE OIL SYSTEMS 7-8

FLUE SYSTEM 9-11

FLUE TERMINAL LOCATIONS 12

AIR SUPPLY 13

ELECTRICAL SUPPLY 14

INSTALLATION CLEARANCES 15

REQUIREMENTS PRELIMINARY INSTALLATION 15

SITE LOCATION 16

INSTALLATION 17

PCB CONNECTIONS 18

COMMISSIONING BURNER ACCESS 19

INSTRUCTIONS ELECTRICAL CONNECTION 19

OIL PUMP CONNECTION 19

ELECTRICAL CHECK 20

FLUE SAFETY DEVICE 20

OVERHEAT SAFETY THERMOSTAT 20

FIT PRESSURE GAUGE 21

VENT OIL PUMP 21

ADJUST OIL PRESSURE 21

SET COMBUSTION AIR 22

ANCILLARY CONTROLS CHECK 23

INSTRUCT THE USERS 23

WIRING DIAGRAM WIRING DIAGRAM - APPLIANCE 24

SINGLE CHANNEL SINGLE CHANNEL PROGRAMMER - OPTIONAL 25

PROGRAMMER

Consumer Protection

As responsible manufacturers we take care to make sure that our products are designed and

constructed to meet the required safety standards when properly installed and used.

IMPORTANT NOTICE: PLEASE READ THE ACCOMPANYING WARRANTY.

Any alteration that is not approved by AGA could invalidate the approval of the appliance,

operation of the warranty and could affect your statutory rights.

Health & Safety

This appliance may contain some of the materials that are indicated It is the Users/Installers

responsibility to ensure that the necessary personal protective clothing is worn when handling

where applicable, the pertinent parts that contain any of the listed materials that could be

interpreted as being injurious to health and safety, see below for information.

Firebricks, Fuel beds, Artificial Fuels

When handling use disposable gloves.

Fire cement

When handling use disposable gloves.

Glues and Sealants

Exercise caution - if these are still in liquid form use face mask and disposable gloves.

Glass Yarn, Mineral Wool, Insulation Pads, Ceramic Fibre

May be harmful if inhaled. May be irritating to skin, eyes, nose and throat. When handling avoid

contact with skin or eyes. Use disposable gloves, face-masks and eye protection. After

handling wash hands and other exposed parts. When disposing of the product, reduce dust

with water spray, ensure that parts are securely wrapped.

Kerosene & Gas Oil fuels (mineral oils)

1. The effect of mineral oils on the skin vary according to the duration of exposure.

2. The lighter fractions also remove the protective grease normally present on the surface of

the skin. This renders the skin dry, liable to crack and more prone to damage caused by cuts

and abrasions.

3. ‘Oil acne’ is recognised by the presence of skin rashes. The arms are most often affected,

but may occur where there is contact with oil or oily clothing.

- Seek medical attention for any rash.

- Avoid skin contact with mineral oil or clothing contaminated with mineral oil.

4. Inhalation of mineral oil vapours must be avoided. Never fire the burner in the open as

unburnt oil vapours are likely to occur.

5. Use a suitable barrier cream which will give protection against mineral oil, lanolin based hand

creams are usually very effective.

6. Never syphon mineral oils by use of the mouth. If accidentally swallowed, call a doctor, do

not induce vomiting.

Oil Inlet R1/4 (1/4” BSP Taper Ext)

Electrical Supply 230V ~ 50Hz 3 amp Fused

Power Flue to 54mm St/St Pipe

right or left

% - COOKER 11.0

Smoke 0 - 1

Fuel - Kerosene Class C2 complying with

BS2869 part 2

Unpacked Weight of Appliance - 326Kg

Firing Rate - 1.44 l/h

Flue Terminal Dimensions (mm) -

Width - 500 mm Height - 210 mm

Depth - 180 mm

TECHNICAL DATA

DESN 512566 A

BURNER NOZZLE (US g/h)

0.40 @ 80° H LE DANFOSS

7.6 (110)

14.6

OIL PRESSURE Bar (psi)

OIL BURNING RATE cc/m

HEAT INPUT kW

BURNER

PLEASE NOTE: IT IS ADVISABLE TO

CHECK THE ACTUAL SIZE/WIDTH

OF YOUR APPLIANCE BEFORE

FINALLY FIXING ANY KITCHEN

UNITS SINCE ENAMELLED CAST

IRON CAN VARY IN SIZE.

R 1/4 (1/4” BSP TAPER)

DIMENSIONS IN MM

FLUE PIPE

OUTLET

ELECTRICAL

SUPPLY

CABLE

The Rayburn is a floor standing cooker, fired by a

pressure jet oil burner.

IMPORTANT

l This appliance must only be used with Kerosene

Class C2 Complying with BS2869 Part 2

l A Fire Valve MUST be fitted in the oil supply line.

l The supplied in line filter MUST be fitted.

THIS APPLIANCE IS A CONTROLLED SERVICE BY

DEFINITION AND REQUIRES EITHER FITMENT

UNDER THE REMIT OF BUILDING CONTROL OR

INSTALLATION BY AN OFTEC REGISTERED 105

TECHNICIAN (CLASSED AS A COMPETENT PERSON)

WHO CAN SELF CERTIFY HIS OWN WORKS.

This appliance must be commissioned by a competent

engineer such as an OFTEC approved.

The installation of the appliance must be in accordance

with the relevant requirements of the current Building

Regulations BS7671 (formerly IEE Wiring Regulations). It

should also be in accordance with the relevant British

Standard Codes of Practice.

BS 5410 Installation of oil fired appliances for space

heating and hot water purposes Part 1 Boilers of rate

output not exceeding 45kW.

The control of Pollution (Oil) Regulations.

FLUE SAFETY DEVICE

For safety purposes a flue safety device is fitted. This will

only operate in adverse or blocked flue conditions. If the

switch has operated, it should be pushed in, to reset. If

this problem persists it is necessary to determine and

rectify the cause. If it is found necessary to reset more

than once this may indicate a flue blockage.

Appliance Hearth. The surface temperature of the floor

below the appliance does not exceed 100ÞC. The

constructional hearth described in current Building

Regulations does not apply. However this appliance must

be installed on a solid floor or base of incombustible

material which is capable of supporting the total weight.

The location chosen for the appliance must permit the

installation and the provision of a satisfactory flue and an

adequate air supply. The location must also provide

adequate space for servicing and for air circulation around

the appliance. See “Installation of the Appliance”.

The space in which the appliance is to be fitted must have

the following minimum dimensions.

Between wall or unit and LH side of appliance - 10mm

top plate

Between wall or unit and RH side of appliance - 10mm

top plate

SHOULD THE WALL PROJECT BEYOND THE FRONT

OF THE APPLIANCE, IT MUST BE INCREASED TO

50mm (SEE FIG. 1). To allow door to open enough to

change oven and shelf positions.

Above the raised insulating cover handle - 60mm

In addition, adequate clearance must be available at the

front of the appliance to enable it to be operated and

serviced. Flue pipes and fittings must not be closer than

10mm to combustible materials and where passing

through a combustible partition such as ceiling or roof,

must be enclosed in a non-combustible sleeve providing

an air space of at least 10mm.

Spaces around flue pipes passing through walls or floors

should be sealed against the passage of smoke and

flame.

Where the cooker is to stand in a recess or against a

wall which is to be tiled, in no circumstances should

the tiles overlap the cooker top plate.

Site requirements

REGULATIONS

LOCATION

INTRODUCTION

10mm

50mm

Fig. 1

WALL PROJECTING BEYOND THE

FRONT OF THE APPLIANCE

10mm

Site requirements

OIL PIPE LINE OIL STORAGE

SEE FIG 2 & 3

The oil supply connection between the storage tank and

the oil pipe should be run in copper or steel pipe with a

minimum diameter of 10mm. Galvanised pipes and

fittings should not be used. Annealed copper pipe is

preferred with flare type manipulative fittings. Capillary

fittings with soft solder should not be used. Steel pipes

should be joined using taper threads.

All pipe work and fittings must be completely air tight.

Only oil resistant compounds and PTFE tape should be

used when making joints. Pipe work must be protected

against damage whether fitted above or below ground.

The size and arrangement of pipe work will depend upon

the distance and height of the oil storage tank in relation

to the oil pump inlet.

The oil line from the storage tank to the appliance

must be fitted with a remote acting fire valve

operating at 66°C (150°F) fitted with an appropriate

length of capillary to enable the valve body to be

located externally at the point where the oil line

enters the building. The heat sensing phial of the fire

valve MUST be fitted to the clips, to the left of the

burner.

The 5-10 micron oil filter supplied with the appliance must

be fitted on the oil pipe line and stop valve must be fitted,

as close to the cooker as possible in an accessible

position.

A flexible pipe connection, approximately 740mm long, is

supplied to fit between the oil supply pipe and the oil

pump for ease of burner removal.

The minimum recommended oil tank size is 1400 litres,

Mild Steel Tanks should be to BS. 799 Part 5 and plastic

tanks to OFTEC standard OFS T100.

HOWEVER in the interests of economical deliveries the

oil tank should be of 3000 litres (600 gallons) capacity.

When positioning the tank, due consideration should be

given to appropriate access for fuel delivery vehicles.

Positioning should comply with the requirements of BS

5410 Pt 1 and OFTEC Technical Book 3.

The tank should be complete with the following:

1. Sludge Cock (steel tanks)

2. Outlet Valve and filter

3. Contents Indicator

4. Vent Pipe

To prevent entry of water or fitted with return bend.

5. Fill pipe and screw cap. (50mm black pipe)

The use of open lids to fill tanks is not approved.

Steel Tanks - should be mounted on suitable supports. If

of masonary, a damp proof membrane should be

positioned between the tank and its supports to prevent

the steel from rusting when in direct contact with water.

Steel Tanks should slope 20mm for each 1m run from the

oil outlet towards the sludge cock (opposite end).

Plastic Oil Tanks - UV Stabilized, plastic tanks are a

modern alternative to steel. These green tanks are

protected against sunlight and do not to stand on piers.

They do however need to be supported over their entire

base. Ideally 50mm smooth faced garden slabs bedded

onto stand or a smooth concrete base.

The single tapped outlet makes them more suited to

single pipe gravity feed or where suction lift is necessary

a single pipe feed with deaereator is ideally suitable.

Site requirements

DESN 510519 A

DESN 510520

Fig. 2

MAXIMUM

LENGTH

(METRES)

H METRES

10mm OD

100

-3.0

100

-3.5

-4.0

Single Pipe oil system

Two Pipe oil system

FILL WITH

CAP

FIRE CHECK

VALVE

FIRE CHECK

PHIAL

FILTER

(SUPPLIED)

FILL

WITH CAP

* VENT WITH

SCREEN

MESH

FIRE CHECK

VALVE

FILTER

(NOT

SUPPLIED)

FIRE VALVE

PHIAL

FILTER

(SUPPLIED)

4 METRES

MAXIMUM

SUCTION

RETURN

20mm PER

METRE FALL

DRAIN

OIL TANK

*VENT WITH

SCREEN MESH

* MAY ALSO BE

MUSHROOM TYPE

* MAY ALSO BE

MUSHROOM TYPE

Site requirements

Fig. 3

Fig. 4

DESN 511459

DESN 511449

ONE & TWO PIPE SYSTEMS

SEE FIG. 4

The cooker as delivered is ready to be used on a one pipe

system. To convert to a two pipe system. (See Fig. 4)

Sections:-

BURNER ACCESS, steps 1 to 3,

BURNER REMOVAL, steps 1 to 5

PUMP FILTER REPLACEMENT steps 1 & 2

1. Remove middle screw

2. Remove horseshoe washer

3. Replace screw

4. Re-assemble in reverse order

Deaerator Oil System

FILTER

(NOT

SUPPLIED)

*VENT WITH

MESH SCREEN

FILL

WITH CAP

FIRE CHECK

VALVE

FILTER

(SUPPLIED)

FIRE VALVE

PHIAL

(MAX)

DEAERATOR

*MAY ALSO BE

MUSHROOM TYPE

1-Pipe Operation:

screw with horseshoe washer

2-Pipe Operation:

screw without horseshoe washer

The flue can be to the left or right of the appliance. The

cooker is supplied with the flue pipe to the left, this can be

adjusted to suit the installation.

FLUE DIRECTION - EXIT TO THE LEFT

1. Remove lower back panel (7 screws).

2. Unscrew the two fixing brackets and remove. (See

Fig. 5).

3. Slacken the jubilee clip, fixing flexible pipe to

horizontal pipe (A). (See Fig. 5).

4. If the flue pipe is to be routed as per factory set,

remove bend from manifold and pipe A.

Smear sealant on the end of the manifold, and replace

bend onto the manifold, ensuring it is fully on and

sweeps under the burner chamber.

5. Smear the sealant over the surface of the 28mm

branch on pipe ‘A’. Push the flexible pipe 30-40mm on

to the branch and tighten the jubilee clip.

6. Smear sealant on the first end of pipe ‘A’ and fit to

bend ensuring the branch pipe is slightly above centre.

7. Replace fixing brackets (4 screws).

8. Replace back panel (7 screws) and position cooker.

Site requirements

FLUE SYSTEM

Fig. 5 DESN 512771

Fig. 6 DESN 512770

FLUE DIRECTION - EXIT TO THE RIGHT

Follow previous instructions in FLUE SYSTEM, Steps 1 to

4. Reposition the flexible tube from the oven vent down

the back of the oven.

5. Smear sealant on the end of the manifold and replace

the bend.

6. Smear sealant on the first end of pipe ‘A’ and the

surface of the 28mm branch (towards the bend). Slide

the flexible pipe completely over the branch (pipe

should point towards burner chamber)

7. Push the first end of pipe ‘A’ onto the bend, the

branch should be above the pipe. Tighten the jubilee

clip ensuring the flexible pipe covers all of the branch

pipe.

8. Replace brackets (4 screws).

9. Replace back panel (7 screws).

Site requirements

Fig. 7 DESN 512669

Fig. 8 DESN 512779

The flue system used on this appliance must be provided

by AGA and must be installed in accordance with the

instructions and standards.

A maximum flue of 5 metres and 5 bends can be used

(including horizontal length on the terminal).

Any upwards vertical runs must be immediate to the

appliance to a maximum of 3 metres. (See Fig. 9)

Downwards vertical runs must be no more than 0.5

metres. (See Fig. 10)

Flue can be positioned to rear or front of appliance via 1

bend. (See Fig. 11).

Horizontal runs must be as level as possible.

Care must be taken on mounting the terminal and routing

the flue:-

a. Damage to damp proof course

b. Height above ground

c. General terminal locations (See Fig. 9)

Where the flue passes through combustible material a

minimum of 10mm clearance must be maintained around

the flue pipe and insulation sleeve.

GENERAL REQUIREMENTS

The flue must be adequately supported using the brackets

specified.

The flue pipe must be insulated (supplied).

All joints should be sealed using the sealant provided.

Site requirements

FLUE SYSTEM

Fig. 9

Fig. 10

Fig. 11

DESN 512574 A

DESN 512575 A

DESN 512573

Site requirements - Flue terminal location

Fig. 12 - Location of flue terminal

A DIRECTLY BELOW AN OPENING, AIR 600mm

BRICK, OPENING WINDOW etc.

B HORIZONTALLY TO AN OPENING, AIR 600mm

BRICK, OPENING WINDOW etc.

C BELOW A GUTTER, EAVES OR BALCONY 75mm

WITH PROTECTION

D BELOW A GUTTER OR A BALCONY 600mm

WITHOUT PROTECTION

E FROM VERTICAL SANITARY PIPEWORK 300mm

F FROM AN INTERNAL OR EXTERNAL 300mm

CORNER

G ABOVE GROUND OR BALCONY LEVEL 300mm

H FROM A SURFACE OR A BOUNDARY 600mm

FACING THE TERMINAL

J FROM A TERMINAL FACING THE 1200mm

TERMINAL

K VERTICALLY FROM A TERMINAL ON THE 1500mm

SAME WALL

L HORIZONTALLY FROM A TERMINAL ON 750mm

THE SAME WALL

DISTANCES STATED ARE MINIMUM ALLOWABLE REQUIREMENTS

The appliance can only be installed in a room which

meets the ventilation regulations in force. But, in any

event the room must have a permanent vent of minimum

free air area, see below.

IMPORTANT: THE LOUVRED AIR INTAKE AT THE

BOTTOM FRONT OF THIS APPLIANCE MUST BE

KEPT CLEAR OF ANY OBSTRUCTIONS

Detailed recommendations for air supply are given in the

Building Regulations, and in BS 5410: Part 1. The

following notes are intended to give general guidance.

1. Combustion and ventilation air supply to oil fired

appliance has to comply with the Building Regulations

and with BS 5410: Part 1. The air supply requirement for

oil fired appliances is 550mm2 per kW of maximum rated

output above 5kW. These requirements are illustrated in

OFTEC Technical Book No.3.

2. The combustion air supply to open flued appliances

should normally be provided at high level into a room

where it will not cause discomfort by creating a cold

draught across the floor.

3. If combustion air is supplied through an under floor

duct the grilles at each end should be positioned in the

vertical plane to reduce the risk of blockage. Ducts should

be sized so as to reduce resistance to air flow.

4. The ventilation requirement for kitchens in Part F of the

Building Regulations is for mechanical extract at the rate

of 60 litres per second or 30 litres per second if the fan is

incorporated in a cooker hood.

Background ventilation is also required, either by

producing a constant mechanical extract rate of one air

change per hour or by having ventilation openings of not

less than 4000mm2.

5. Extract fan should be positioned as far away from the

appliance as possible and should have a sufficient

dedicated air supply. To undertake a test the oil fired

appliance should be set in operation and the doors and

windows of the room containing it should be closed. The

extract fan should then be run at its maximum setting. The

oil fired appliance should be observed to operate

satisfactorily both before and after the fan is switched on.

6. It is preferable for the air supply for an extract fan to be

located where it can serve the fan without the air stream

passing close to the oil fired appliance.

7. Oil fired appliances must not draw combustion air from

a garage.

Site requirements

AIR SUPPLY

400K 61 cm

MODEL MIN. AIR REQUIREMENT

AIR SUPPLY

Wiring external to the appliance must be installed in

accordance with current National Wiring Regulations and

any local regulations which apply. The appliance is

supplied for 230 Volt ~ 50Hz and a fuse rating of 3 amps.

The method of connection to the mains supply should

facilitate complete electrical isolation of the appliance, by

the use of a fused double pole switch having a contact

separation of at least 3mm serving only the appliance.

The point of connection to the mains should be readily

accessible and adjacent to the appliance. The installation

should be protected by a 30mA Residual Current Circuit

Breaker (RCCB).

The minimum requirement for the power cable is that it

should be a 3 core PVC sheathed flexible cord (85°C min)

at least 0.75mm2 (24 x 0.2mm) to the relevant standard.

WARNING THIS APPLIANCE MUST BE EARTHED

In the event of an electrical fault after installation of the

appliance, preliminary electrical system checks must be

carried out i.e. earth continuity, short circuit, polarity and

resistance to earth.

For wiring instructions see wiring diagrams.

Site requirements

ELECTRICAL SUPPLY

The appliance is floor mounted. The space in which the

appliance is to be fitted must have the following minimum

dimensions.

Between wall or unit and LH side of appliance - 10mm

top plate

Between wall or unit and RH side of appliance - 10mm

top plate

SHOULD THE WALL PROJECT BEYOND THE FRONT

OF THE APPLIANCE, IT MUST BE INCREASED TO

50mm (SEE FIG. 1). To allow door to open enough to

change oven and shelf positions.

Above the raised insulating cover handle - 60mm

In addition adequate clearance must be available at the

front of the appliance to enable it to be operated and

serviced.

The appliance is delivered in a fully assembled condition

with the exception of the following items which are

supplied separately packed and require assembly:-

The appliance rear distance bracket.

The cooker handrail.

The oil filter and the flexible oil feed pipe.

FLUE PIPE KIT

Flue pipe kit comprises of:-

3 x 1 metre length of flue pipe

3 elbows

3 straight couplers

6 support brackets (saddle and clamps)

1 tube ultra-grey sealant

Pack of fastenings

Appliance rear distance bracket: if the rear wall is of

combustible material, there must be an air gap of 25mm

between the wall and the rear of the cooker. Fit the rear

distance brackets as shown in Fig. 13. Whenever possible

it is recommended that the skirting board is removed for

the width of the appliance to enable the rear edge of the

appliance top plate to make contact with the vertical wall

and avoid a rear gap. (Combustible wall excepted).

Where the cooker is to stand in a recess or against a wall

which is to be tiled, IN NO CIRCUMSTANCES SHOULD

THE TILES OVERLAP THE TOP PLATE.

The handrail brackets are held on the front edges of the

cooker top-plate casting. Remove the travel nuts and

replace with the handrail brackets ensuring the fibre

protecting washers are in position. Insert the handrail with

fitted end caps into the brackets, positioning them

correctly, and tighten the locating bolts (Fig. 14).

Installation requirements

CLEARANCES

PRELIMINARY INSTALLATION

Fig. 13

FIG. 14

DESN 512553

DESN 510454 ‘A’

Installation requirements

SITE LOCATION

1. Check that the hearth is level, then remove the

appliance from its transit wooden pallet, and position

it with its back against the wall and in its intended

position for flue connection.

2. Locate and fit flue pipe.

3. Connect and terminate the flue system in accordance

with these instructions.

1. Cut out card template from packaging and affix to wall.

2. Cut ø60mm hole in the wall for the flue pipe (See Fig.

15).

3. Drill 4 wall fixing holes through template (1 in each

corner). (See Fig. 15).

4. Drill a minimum of a ø10mm hole through the wall for

terminal supply cable.

5. Remove card template and place flue terminal

assembly onto the hole. (See Fig. 16).

6. The flue termination pipe may require to be shortened

or lengthened depending on wall thickness. (See Fig.

17).

7. Using the large wall fixings permanently fix back plate

to the wall, remove outer cover first.

8. Wire the fan to the supply cable to the terminal block

on the back plate. (See Fig. 18).

Using the 3-core cable provided, run cable back to flue

extractor circuit control at the bottom right hand side

of the appliance.

9. An additional terminal guard is not required for this

appliance.

Installation Requirements

INSTALLATION

Fig. 16 DESN 513356

DESN 512561

DESN 513350

Fig. 17

Fig. 18Fig. 15 DESN 513345

RED + TO RED +

Installation Requirements

Fig. 19

EXTERNAL CONNECTIONS : FAN CONNECTIONS - AT TERMINAL

MAINS CONNECTIONS

PCB CONNECTIONS

NOTE: SMOKE/SMELL EMITTED DURING

INITIAL USAGE.

During Initial usage of operation of the cooker,

smoke/smell may be emitted and is normal and not a fault

with the appliance, it is therefore advisable to open doors

and or windows to allow for ventilation.

- SEE FIG. 20

1. Open the burner access door.

2. Remove (5) inner panel securing screws and remove

panel.

3 Remove the (3) plinth securing screws and remove

plinth.

1. Make electrical connections to terminal strip as wiring

diagram (See Fig. 19)

- SEE FIG 21

1. Bring the sensing phial of the fire valve through the

grommet in the left hand side panel and locate behind

the casting to the left of the burner opening.

2. Connect the flexible hose to the outlet pipe from the oil

filter. DO NOT pass the flexible oil hose through the

side panel casing. If necessary use 10mm O/D copper

tube between the hose and oil filter.

3. Before connecting the flexible oil pipe to the pump

inlet, open the stop valve slowly and run off some of

the oil into a receptacle to establish an air free supply

to the pump. Make the connection onto the pump oil

tight and leave valve open.

Commissioning Instructions

Fig. 20 DESN 511424

DESN 511426Fig. 21

BURNER ACCESS

OIL PUMP CONNECTION

ELECTRICAL CONNECTION

Checks to ensure electrical safety should be carried out

by a competent person.

This thermostat is a safety cut-out device which will

operate under adverse wind or a blocked flue condition. It

is a manually reset device which can be resey by pressing

in the centre.

IMPORTANT NOTE: This appliance is fitted with an

overheat thermostat which has a manual reset button.

If the overheat stat trips, the cooker will not operate,

until the button has been pushed-in (reset). The

engineer needs to follow ‘Fault Finding Guide’ to

establish why it has tripped. (The overheat thermostat

and its sensing phial are located on the controls

chassis rear).

FLUE SAFETY DEVICE

ELECTRICAL CHECK

Commissioning Instructions

OVERHEAT SAFETY THERMOSTAT

Page is loading ...

Rayburn XT Series Installation guide

Brand: Rayburn

Model: XT Series

Category: Fireplaces

Type: Installation guide

Download PDF

report

Rayburn XT Series Installation guide

Rayburn XT Series Installation guide

Related papers

Other documents