SBS TTACTIONCAMDG User manual

Compact Action Camera with CMOS Sensor, HD Resolution

Universal

TTACTIONCAMDG - User Manual

Page is loading ...

UK

USER MANUAL

Please read carefully this manual before to start the

camera’s use, to maximize its performance and extend the

life of the product.

APPEARANCE AND BUTTONS

1 Shutter button

2 LCD display

3 Power button

4 Lens

5 Indicator Light for charging (Red)

6 Microphone

7 Working Indicator Light (Blue)

8 Mode Switch

9 Micro USB port

10 Micro SD card slot

11 Reset button

LCD DISPLAY ILLUSTRATION

Turn on the Action Cam: the LCD will display the following

status and settings:

1 Camera mode

2 Video recording mode

3 Vehicle- mounted mode

4 SD card icon (displayed when loaded)

5 Resolution icon: in camera mode, HI stands for 5

Megapixels (2592x1944), and in video recording mode

or vehicle mounted mode, it stands for 720P (1280x720).

In camera mode LO stands for 1 Megapixel (1280x960),

and in video recording and vehicle mounted mode, it

stands for 640P (640x480).

6 Battery icon: current battery level

7 Counter: display up to 9999

8 Timer: display minutes and seconds

NOTE: the above icons may vary according to the status of

the Action Cam.

WORKING MODE FLOW CHART

After turn on the Camera, you can change the Power button/

Mode switch to switch the following modes in turn:

In video recording and vehicle-mounted mode , press the

Shutter button to start recording, Working Indicator Light

ash，and than press it again to stop; in camera mode, press

the Shutter button to take photo.

Use your Action Cam

When you use the Camera for the rst time please:

1. Insert the micro SD or micro SDHC card (NOT

INCLUDED), as shown in the following picture. High speed

card at least Class 4 is recommended; 8Gb capacity SD

allows to records about 1h of video,

16Gb 2h, 32Gb 3h, 64Gb 4h. Turn

off the Action Cam before inserting

or removing the card.

2. How to charge the battery. The Cam uses built-in

rechargeable lithium battery. When the Cam is off, connect

it to the PC by an USB cable to charge the battery. During

recharge, the charging light indicator will light on, will be off

when recharge completes.

Turn on/off

Turn on: press and hold the button for about 2 seconds,

LCD displays “ON”.

Turn off: press and hold the button for about 3 seconds,

LCD displays “OFF”.

POWER BUTTON MODE SWITCH

MODE SWITCH POWER BUTTON

NOTE: The Action Cam will turn off automatically if it is

inactive for 5 minutes.

Start to Use

The Action Cam provides different shooting modes.

Conversion is available via the mode switch after startup:

video

recording

mode

HI stands for 720P (1280x720,30 fps) video

Lo stands for 640P (640x480,60 fps) video

picture

taking

mode

HI stands for 5M (2592 x 1944) resolution

Lo stands for 1M (1280x 960) resolution

vehicle-

mounted

mode

HI stands for 720P (1280x720,30 fps) video

Lo stands for 640P (640x480,60 fps) video

1. Video Recording

To record a video, please check whether the Cam is under

Video mode. The icon is played on the screen.

Start recording: press and release the button, the icon

and [:] displayed in LCD will ash. At the same time the

blue indicator will ash too, meaning that the recording is in

progress.

Stop recording: press and release the button, the icon

and [:] displayed in LCD will stop ashing. At the same time

the blue indicator will stop ashing either, meaning that the

recording is stopped.

When the SD card is full, or the battery runs out, the

recording will stop automatically, and the recorded video will

be saved before Action Cam turns off.

2. Photo

To take a photo, please check whether the Action Cam is

under Camera mode: the icon is displayed on the screen.

Press and release the button: the blue indicator will ash,

meaning that a photo is taken (If you take more than 9999

photos, the LCD display will stop at 9999)

3. Vehicle-mounted recording

To record a video, please check whether the Cam is turned

on Vehicle-mounted mode. The icon is displayed on

the screen.

Start recording

Press and release the button, the icon and [:]

displayed on LCD will ash. At the same time the blue

indicator will ash too, meaning that the recording is in

process.

Stop recording

Press and release the button, the icon and [:]

displayed in LCD will stop ashing. At the same time the blue

indicator will stop ashing either, meaning that the recording

is stopped.

Press the shutter button once in the preview mode to begin

recording, save a segment for recording every 3 minutes,

then start to record the following segment of video. When the

SD card is full, the earliest segment of video will be deleted

to release the corresponding space for continuous recording.

4 . PC connection

4.1 Turn on the Action Cam and connect it to the USB port of

the PC using the equipped USB cable. Cam will enter U-disk

mode and the LCD will display as in below draw:

Now you can view the photos or videos taken by the Cam on

your PC.

4.2 In U-disk mode (PCO mode), press the Shutter button

to switch to web cam mode (PCC mode): the LCD will

display as in below draw:

Now you can start the web cam through

application. To return to U-disk mode (PCO

mode), press the button again.

NOTE: Driver is not required using web cam mode (PCC

mode) with Windows XP(SP3) or upper version.

5. Set system and date time

You can set time and date system as per following

instruction:

1 Connect the Camera to computer

2 In the root directory of SD create a new le TIMESYNC.

TXT

3 Edit TIME.TXT is:

[date]+spacebar+enter

2014/06/01+space bar+enter

15:45:00+spacebar+enter

4 Save and exit the editing

5 Reboot the device: clock will be set

DIRECTIVE 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on waste electrical and

electronic equipment (WEEE)

Information for users

(a) the device requirement not to dispose of WEEE as unsorted municipal

waste and to collect such WEEE separately;

(b) the device must return and collection systems available to them;

(c) the device will be collected by the vendor in case of a new one is buyed

(d) the device not correctly disposed has potential eects on the environment and human health

as a result of the presence of hazardous substances in electrical and electronic equipment;

(e) The symbol indicating separate collection for electrical and electronic equipment consists of the crossed-out wheeled bin,

as shown below. The symbol must be printed visibly, legibly and indelibly.

Page is loading ...

SBS TTACTIONCAMDG User manual

SBS TTACTIONCAMDG User manual

in other languages

Other documents