AEG SU96043-6I Installation guide

Page is loading ...

7

ab

c

C

click

8

b

=

9

I

c

Möbeltür Innenseite

a

I

27,5 cm

55 cm

10

F

Page is loading ...

23

7

ab

c

C

click

8

b

=

9

I

c

Möbeltür Innenseite

a

I

27,5 cm

55 cm

10

F

Boven

Page is loading ...

26

Grid preparation

When changing the side at which the door opens, remove plug from

the mains.

Left door opening:

Remove the left side (A) of the grid cutting it

from the rear (see figure)

Right door opening:

Remove the right side (B) of the grid cutting

it from the rear (see figure)

Re-install the grid to the base of the appli-

ance by pushing on to the clasps (a) until

they click.

Reversing the door

The side at which the door opens can be changed from the right side

(as supplied) to the left side, if the installation site requires.

To reverse the opening

direction of the door,

proceed as shown in

the figures:

27

Changing over the freezer compartment door

(not on all models)

Warning!

After completion of the door

reversing operation, check

that the door gasket adheres

to the cabinet. If the ambient

temperature is cold (i.e. in

Winter), the gasket may not

fit perfectly to the cabinet. In

that case, wait for the natural

fitting of the gasket or accel-

erate this process by heating

up the part involved with a

normal hairdryer on a low set-

ting.

1. Open the freezer compartment door a lit-

tle way.

2. Using a small screwdriver, press the

spring in the opening of the lower door

bearing slightly upwards and take the

door bearing out complete with the

door.

1xA

2xD

1xB

2xC

2xL

18xI

2xF

2xG

1xK

1

28

3. Position the covering cap (M) on the

opposite side.

4. Turn the freezer compartment door

through 180° and fit the lower door

bearing into the lower bearing cavity

of the freezer compartment door.

5. Lift the freezer compartment door a

little way upwards, fit it into the

upper door bearing, and at the same

time insert the lower door bearing

into the square hole. Small upwards

and downwards adjustments of the

freezer compartment door will make

fitting easier.

Installation kit

Building the appliance in under a worktop

The dimensions of the recessed

installation area must correspond

with those indicated in the figure.

29

Two cabinet securing brackets are supplied with the installation pack.

They need to be assembled onto the cabinet prior to cabinet being

pushed into the Kitchen aperture.

1. To fit these brackets remove the two

screws at the top left and right hand

front corners of the cabinet.

2. Position the two brackets

as shown in the figure and

replace the two securing

screws.

3. Push the appliance

into place. The plug

socket necessary for

connection of the

appliance to the elec-

tricity supply should

be positioned, so that

the plug is not placed

in the recess.

4. To adjust the height

proceed as follows:

Loosen or tighten the

two front feet.

The rear feet are adjusted by turning the screw in the front kick plate

to the left or right.

Left hand bracket Right hand bracket

2

b)

Screw appliance into place

5. The joint cover (B) is to be

assembled after having installed

the appliance in the recess.

30

B

4

1

5

I

31

Mounting furniture door

a

b

10

1

2

3

4

C

6

7

ab

c

C

click

8

Page is loading ...

33

8 mm

13

G

K

I

F

90°

115°

L

15

Refit the covering strip.

14

A

34

Fitting the plinth

Important!

For the efficient operation of the appli-

ance, it is important that the original

ventilation grid is used.

•If the opening height dimension is

A=820 mm, the plinth height must be

a=100 mm.

If the opening height dimension is

B=890 mm, the plinth height must be

b=170 mm.

• For intermediate heights cut the

plinth to a requested height, but pay

attention that it does not cover or

exceeds the ventilation grid.

• Attach plinth to the kitchen units.

a = 100

b = 170

25 - 80

A = 820

B = 890

25

DO008c

Important! The plinth must be positioned at a minimum distance of

25 mm from the door.

Page is loading ...

66

7

ab

c

C

click

8

b

=

9

I

c

Möbeltür Innenseite

a

I

27,5 cm

55 cm

10

F

Page is loading ...

AEG SU96043-6I Installation guide

This manual is also suitable for

AEG SU96043-6I Installation guide

in other languages

Related papers

Other documents