7275.200
M968490
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please read these instructions carefully
before you begin.
Installation Instructions
ROUGHING-IN DIMENSIONS
DISTILLED & PURE WATER FITTINGS
[105mm]
4-1/8"
[305mm]
12"
[22mm]7/8" DIA.
[51mm]
2" DIA.
-5
/
8
"
4
3mm
]
4-1
/
8
"
[105mm]
1/16"-1-5/8"
[2mm-41mm]
WARE THICKNESS
1/2" NPT MALE
THREAD INLET
"
DIA.
[
51mm
]
2
DIA.
[
22mm
]
7
/
8
"
1
3"
[
330mm
]
1/
8
"
5mm]
[140mm]
5-3
/
8
"
6-3
/
8
"
[
162mm
]
1
/
16"-1-
3
[2mm-35mm]
WARE THICKNES
S
3-1
/
2
"
[89mm]
/
[89mm]
/
1
/
4" NPT MAL
E
THREAD INLET
DEX
W'
[70mm]
2-3/4"
[318mm]
12-1/2"
[226mm]
8-7/8"
"
[152mm]
6
1/16"-1-3/8"
[2mm-35mm]
WARE THICKNESS
7/8" DIA. [22mm]
18"
[457mm]
MINIMUM
[54mm]
2-1/8" DIA.
POLYPROPYLENE TUBE FITTING
3/8" NPT MALE THREAD INLET
PFA TUBING
1/4" [6mm] O.D.
3
˚
3
7275.300
7275.100
7275.200
(Pure Water)
7275.100
(Pure Water)
7275.300
(For Distilled
Water)
7275.200
1
M968490
Drill a one inch dia. hole in mounting surface if required. Mounting holes in ware can range from 1" to 1-3/8" dia.
Remove mounting nuts, washers, coupling nuts and pipe connection from spout shank if attached.
Assemble rubber washer onto body shank.
Place body shank through hole in mounting surface and align fitting. Assemble steel washer
and lock nut. Tighten securely.
Pipe to service to complete installation. See rough-in drawings for pipe connection
requirements.
After installation is complete turn service on and check all connections
for leaks.
TOOLS AND SUPPLIES REQUIRED
Adjustable Wrench
Teflon Tape
Drill
Plumbers' Putty or
Caulking
INSTALLATION IS TYPI
C
AL FOR AL
L
W
ATER FITTING
S
Channel Locks
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
7275.300
7275.100
INSTALL FITTING [7275.100, 7275.200, 7275.300]
L
OC
K N
UT
S
TEEL WA
S
HE
R
FITTIN
G
BA
SE
B
O
D
Y
S
HAN
K
R
U
BBER WA
S
HE
R
IMPORTANT: FLUSH ALL SUPPLY LINES PRIOR TO FITTING INSTALLATION.
7275.200
S
ERRATED TI
P
M
96
2
3
1
8
-
00
2
0A
M968490
Product names listed herein are trademarks of American Standard Inc.
©American Standard Inc. 2004
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays
8:00 to 7:00 p.m. Eastern Time
CANADA
1-800-387-0369 (TORONTO 1-905-306-1093)
AVAILABLE REPAIR PART
S
7275.300
7275.100
COLD WATER INDEX
M
96
2
3
12-
00
7
0A
M
OU
NTIN
G
COU
PLIN
G
KI
T
M962320-0070
A
HANDLE
96
2
3
1
0
-
00
2
0A
S
HANK M
OU
NTIN
G
KI
T
M
96
2
3
24-
00
7
0A
/
