amPHILI FUJI S0176PH Installation guide

Brand
amPHILI
Model
FUJI S0176PH
Type
Installation guide
amPHILI Inc. 1-888-680-0086 www.amphili.com ver.2012-03-29
1
FUJI Range Hood Installation Instruction
WARNING: This installation instruction is written for professional technicians who are experienced in
the building code, electrical and electronic products installation! This instruction is for reference only.
We are not responsible for any damage, injury caused by the installation of the product.
Models：FUJI S0176PH, FUJI CXW200-04A
Personnel：
1. Minimum two persons required；Be able to lift 20KG
2. Be familiar with building code, electrical and electronic products installation；
3. Experienced with have all Personal Protection Equipment such as goggles, gloves etc.
Tools List：
1. Screw Drivers: Philips head and slot head；
2. Electric drill with bits and hole saw；
3. Jig saw；
4. Extension cord, 18AWG wires
5. Goggles, protection gloves, helmet；
6. Portable Vacuum cleaner ；
7. Aluminum tape and electrical tape；
8. Wire binder and wire nuts；
amPHILI Inc. 1-888-680-0086 www.amphili.com ver.2012-03-29
2
Installation Steps：(For reference only, actual procedure may vary)
Preparation
Understand the work：
1. New installation or replacement
2. Minimum width: 30 inch；
3. Exit: upward or backward
4. Shape of the duct: Square（3- ¼ x 10 inch）or round（6 inch Dia. Or other size）；
5. Decide if duct adapter needed（Reno Depot，HomeDepot，etc）；
Figure 1
Square to round adapter，
Standard size: 3- ¼ x 10 inch.
Figure 2
Round duct，
Standard: 6 inch Dia.
If the original duct is only 4 inch, need a 6 inch to 4
inch adapter or to cut the 6 inch duct to fit into 4 inch
then fixed with a screw and sealed with the
aluminum tape.
Step 1
Open the package, check all the accessories. Choose the correct
duct exit(Square or Round) comes with the Range hood.(Default,
round exit installed)
（WARNING: The glass air guide is fragile1 Do not break it.）
(Tips: Put the foam in the package under the range hood to
protect the glass.)
Step 2
(Optional)
It is recommended to remove the metal “L” shaped brackets from
both sides.
Step 3
For stainless steel, do not remove the protection film now! You can life the foam edge to make
it easier to remove the foam later after installation completed.
Step 4
(Optional)
In order to keep a gap between the back of the, range hood body and wall, use the tape to fix 2
layers of the card board onto the wall. This gap will help to install the three screws back later
on the fact plate.
（This step is optional, just make sure the rang hood is not too close against the wall, leave a
gap between the range hood back and wall）
amPHILI Inc. 1-888-680-0086 www.amphili.com ver.2012-03-29
3
Step 5
Check the size and location of opening on the top cabinet. Make sure the opening is big
enough for the range hood exit and also has enough room to use hand to align the duct with the
range hood exit and seal with aluminum tape.
If the opening is not enough or not at the right place, use the jig saw to enlarge the hole to
make it fits.
(Tips: use pencil to draw the lines first then use the jig saw to cut the board)
Step 6
(WARNING: Make sure the power has been shut off!, Make sure a sign has been put at
the breaker panel to make sure nobody will accidentally switch on the power!)
Check if the conduit is long enough to extend the supply wires to the supply entrance of the
range hood. Extend with right fittings if necessary.
Step 7
Put the range hood on the foam with the face plate facing up.
Remove the five screws and disconnect the lamp wires connector
and detergent exit pipe. Remove the metal faceplate.
Step 8
Make sure the duct can fit the exit of the rang hood. Cut or extend if
too long or too short. (Duct extension or adapter are available at
Rene Depot or Home Depot）；
Use a screw and aluminum tape to fix and seal the duct.
Step 9
Fix the range hood to the cabinet from below by using 4 wood
screws provided in the package.
Step 10
Wiring：
1. Remove the knock out on top right；
2. Use conduit fitting to secure the conduit onto the knock out；
3. From the bottom, unscrew the wiring compartment cover screw.
Remove the cover.
4. Connect the Green grounding wire to the bare copper wire with
wire nuts；
5. Connect black wire (Line) to black wire with wire nut；
6. Connect the white wire (Neutral) to white wire with wire nut；
7. Put the wire compartment cover back.；
amPHILI Inc. 1-888-680-0086 www.amphili.com ver.2012-03-29
4
Step 11
Install faceplate：
1. Connect the lamp wire connector back as well as detergent exit pipe disconnected in
STEP-7；
2. Insert the front of the faceplate into the flange of the enclosure and put on the two screws
on front end. Then put on those three screws at the back end clos2 to the wall；
（Make sure the screw is align to the hole. Do not force the screw into the hole.）
Step 12
Remove the cardboard taped on the wall in STEP-4.
Use fingers to pull out the black rubber pipes from the holes.
Step 13
Install three oil reservoirs；The big one at back is slid in. Those two
under the fan are twist and lock.
Step 14
Remove the protection film from the stainless steel enclosure；
Use the portable vacuum cleaner to clean the work place
Step 15
Test run：Fan power, lamp, fan speeds etc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

amPHILI FUJI S0176PH Installation guide

Brand
amPHILI
Model
FUJI S0176PH
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents