Hotpoint Washer/Dryer WDL 540 P/G/A/K User manual

Brand: Hotpoint

Model: Washer/Dryer WDL 540 P/G/A/K

Category: Washing machines

Type: User manual

This manual is also suitable for

WDL 540 P/G/A/K

Hotpoint Washer/Dryer WDL 540 P/G/A/K is a washing machine with a capacity of 1 to 7 kg for the wash program and 1 to 5 kg for the drying program. It has a maximum spin speed of 1400 rotations per minute and an energy rating of A. The Washer/Dryer has a variety of features, including:

A range of wash cycles to choose from, including a quick wash cycle and a delicate cycle.
A drying function that allows you to dry your clothes in the same machine after washing them.
A range of temperature settings, so you can wash your clothes at the correct temperature for the fabric.
A range of spin speed settings, so you can choose the right spin speed for the type of fabric you are washing.

A range of wash cycles to choose from, including a quick wash cycle and a delicate cycle.
A drying function that allows you to dry your clothes in the same machine after washing them.
A range of temperature settings, so you can wash your clothes at the correct temperature for the fabric.
A range of spin speed settings, so you can choose the right spin speed for the type of fabric you are washing.

English, 1

! This symbol reminds you to read this booklet.

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the Washer-dryer and

starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 11

General safety

Disposal

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the Washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13-14

Assistance, 15-16

WDL 540 P/G/A/K

Instructions for use

WASHER-DRYER

Installation

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting du-

ring operation. If it is placed on a fitted or loose carpet,

adjust the feet in such a way as to allow enough room

for ventilation beneath the washing machine.

Electric and water connections

Connecting the water inlet hose

1. Connect the supply pipe

by screwing it to a cold

water tab using a

3/4 gas threaded connec-

tion (see figure).

Before performing the

connection, allow the wa-

ter to run freely until it is

perfectly clear.

2. Connect the other end of

the water inlet hose to the

washing machine,

screwing it onto the ap-

pliance’s cold water inlet,

situated on the top right-

hand side on the rear of the

appliance (see figure).

3. Make sure there are no kinks or bends in the hose.

! The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

! If the water inlet hose is not long enough, contact a

specialist store or an authorised serviceman.

! Ensure that the supply taps are allowing water throu-

gh. Old taps may seize in the closed position and thus

prevent water reaching the machine.

! Keep this instruction manual in a safe place for future

reference. Should the appliance be sold, transferred or

moved, make sure the instruction manual accompanies the

washing machine to inform the new owner as to its opera-

tion and features.

! Read these instructions carefully: they contain vital

information on installation, use and safety.

Unpacking and levelling

Unpacking

! This is a separate part

of the polystyrene base

and should be removed

with the base.

! IMPORTANT check when

unpacking your machine.

1. Unpack the washing machine.

2. Check whether the washing machine has been dama-

ged during transport. If this is the case, do not install it

and contact your retailer.

3. Remove the 4 protecti-

ve screws and the rubber

bush with the respective

spacer, situated on the

rear of the appliance (see

also the installation leaflet).

4. Seal the gaps using the plastic plugs provided.

5. Keep all the parts: you will need them again if the

washing machine needs to be moved to another location.

! Packaging materials are not children’s toys.

Levelling

Your machine may make a

considerable amount of noise

if the two front feet have not

been adjusted correctly.

1. Install the washing ma-

chine on a flat sturdy floor,

without resting it up against

walls, furniture cabinets or

other.

2. If the floor is not perfectly level, compensate for any

unevenness by tightening or loosening the adjustable

front feet (see figure); the angle of inclination, measu-

red according to the worktop, must not exceed 2°.

• the supply voltage is included within the values

indicated on the Technical details table

(see page 5);

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate

use. Before using the appliance please read the instruc-

tions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must

not be used until a replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or

the colour that is embossed in words on the base of the

plug. Replacements can be obtained directly from your

nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug and

you should wish to re-route the mains cable through

partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere re-wearable

plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be accidentally

inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

The drain hose may be

connected to an under-

sink trap. Before connec-

ting the drain hose from

the machine ensure that

any blanks or removable

ends have been taken off

the spigot.

If it is place over the

edge of a basin or sink

be sure the free end of

the hose should not be

underwater.

! We advise against the use of hose extensions; in case

of absolute need, the extension must have the same

diameter as the original hose and must not exceed 150

cm in length.

Ensure that if the drain hose is pushed into a standpi-

pe, that the end does not go down more than 15cms

(6 inches). If the hose is pushed down too far, this may

cause the machine to self -syphon ie. continuously

empty as it is filling.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated in the Technical

details table (see page 5);

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

As the colours of the wires in the lead may not corre-

spond with the coloured markings identifying the termi-

nals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or coloured

Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted with

a 13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt about the electrical supply to

your machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the plug

body and dispose of it as described above.

! The Washer-dryer should not be installed in an out-

door environment, not even when the area is sheltered,

because it may be very dangerous to leave it exposed to

rain and thunderstorms.

! When the Washer-dryer is installed, the mains socket

must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or dange-

rously compressed.

! The power supply cable must only be replaced by an au-

thorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

The first wash cycle

Once the appliance has been installed, and before you

use it for the first time, run a wash cycle with detergent

and no laundry, using the wash cycle 1.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Technical data

Model

WDL 540 P/G/A/K

Dimensions

width 59.5 cm

height 85 cm

depth 53.5 cm

Capacity

from 1 to 7 kg for the wash programme

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data plate

fixed to the machine

Water connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1400 rotations per minute

Energy rated

programmes

according to

regulation

EN 50229

Wash: programme 1; temperature 60°C;

using a load of 7 kg.

Drying: first drying cycle performed with

2 kg load, by selecting the

dryness level.;

the second drying cycle performed with

5 kg load, by selecting the

dryness level.

This appliance conforms to the following

EC Directives:

- 2004/108/EC (Electromagnetic Compatibility)

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Description of the Washer-dryer and

starting a wash cycle

Detergent dispenser drawer: used to dispense de-

tergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: switches the Washer-dryer on and off.

WASH CYCLE knob: programmes the wash cycles. During

the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to

the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold

wash cycle (see “Personalisation”).

DRYING knob: used to set the desired drying program-

me (see “Personalisation”).

WASH CYCLE PROGRESS

indicator light

s: used to mo-

nitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the DOOR

LOCKED indicator light is switched off, the door may

be opened (wait approximately 3 minutes).

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

activity is detected. Press the ON-OFF button briefly

and wait for the machine to start up again.

TEMPERATURE

knob

Detergent dispenser drawer

WASH CYCLE PROGRESS indicator

lights

FUNCTION

buttons with

indicator lights

ON/OFF

button

DRYING

knob

DOOR

LOCKED

indicator light

START/PAUSE

button with

indicator light

Control panel

WASH CYCLE

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has begun,

the indicator lights switch on one by one to indicate which

phase of the cycle is currently in progress.

Note: during the “Drain” phase, the indicator light corre-

sponding to the “Spin” cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the pro-

grammed wash cycle, the corresponding indicator light will

flash and the function will not be activated.

If a function which is incompatible with another function

selected previously, only the most recent selection will

remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked to

prevent it from being opened accidentally; to avoid any

damage, wait for the indicator light to switch off before you

open the appliance door (wait approximately 3 minutes).

! If the START/PAUSE indicator light (orange) flashes

rapidly at the same time as the function indicator light,

this indicates a problem has occurred (see “Troublesho-

oting”).

Starting a wash cycle

1. Switch the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds,

then only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indica-

tor light will flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the drying cycle if necessary (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a

fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the indicator light will switch on. The DOOR LOCKED indicator light will switch off,

indicating that the door may be opened (wait approximately 3 minutes). Take out your laundry and leave the appliance

door ajar to make sure the drum dries completely. Switch the Washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin

Dry

End of wash cycle

Note: as soon as a drying level

or time period has been set,

this indicator light illuminates

to indicate that the selected

wash cycle will be followed by

a drying phase.

Wash cycles

Table of wash cycles

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration

can vary according to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balan-

cing and any wash options selected.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 1 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 1 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.

(*) Ready to Wear

This cycle was designed to wash and dry lightly soiled small loads quickly. By selecting this cycle it is possible to

wash and dry a maximum load of 1 kg in just 60 minutes.

Please note, this is an automatically programmed wash and dry cycle, therefore it is not possible to manually

set a drying time or drying level in conjunction with this cycle.

Please note, the Drying indicator illuminates only during the drying phase of the cycle, not when the cycle is

first selected.

Anti-crease

This function interrupts the wash programme, and the washing is left to soak in water before the appliance is drained.

It can only be used with programme 10 (Silk) and helps to prevent the formation of creases.

To complete the cycle press the START/PAUSE button.

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max. load

(kg)

Cycle

duration

Wash

Fabric

softener

Normal

Mini

load

Normal

Mini

load

Essentials cycles

Cottons: extremely soiled whites.

90° 1400

  

7 3 160 105

Cottons (1): heavily soiled whites.

60° 1400

  

7 3 155 100

Cottons (2): lightly soiled whites and delicate colours. 40° 1400

  

7 3 150 95

Cottons: heavily soiled whites and resistant colours.

60° 1400

  

7 3 130 100

Coloureds Cottons (3): lightly soiled and delicate colours.

40° 1400

  

7 3 85 70

Synthetics: heavily soiled resistant colours.

50° 800

  

3 1.5 80 65

Fastwash 60': to refresh lightly soiled garments quickly (not

suitable for wool, silk and clothes which require washing by hand).

60° 1400

  

3 - 60 -

Special cycles

Baby cycle: heavily soiled delicate colours.

40° 800

  

2 1 120 95

Shirts

40° 600

  

2 1 70 65

Ready to wear (*)

30° 800

  

1 - 60 -

Wool: for wool, cashmere, etc.

40° 800

  

1.5 1 55 50

Silk: for garments in silk and viscose, lingerie.

30° 0 -

 

1 1 55 50

Drying cycles

Cottons

- -



- - 5 - - -

Synthetics

- -



- - 3 - - -

Wool

- -



- - 1.5 - - -

Partials wash cycles

Rinse Fast

- 1400



7 3 35 30

Spin Fast

- 1400



- - 7 - 15 -

Pump out

- 0 - - - 7 - 2 -

Personalisation

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash ( ).

The Washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum value

set for each wash cycle.

Setting the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: from 40 to 180 minutes.

B - Based on the how damp the clothes are once they

have been dried:

Iron : slightly damp clothes, easy to iron.

Hanger : dry clothes to put away.

Cupboard : very dry clothes, recommended for to-

welling and bathrobes.

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent

table), perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them

back in the drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the

remainder of the load.

N.B: when the drying is complete there is a cooling period, even though the DRYING knob is in the position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select the

desired drying duration using the DRYING knob.

Functions

The various wash functions available with this Washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in conjunction

with the selected wash cycle.

Slow Spin (1400-600)

By selecting this function, reduces the spin speed.

! This function may not be used in conjunction with wash cycles 8, 10, 11, 12, 13, C.

Mini load

This function is recommended for when the load of laundry is equal to half, or less than half, of the maximum recom-

mended load (see Table of wash cycles).

! This function may not be used in conjunction with wash cycles 5, 8, 11, 12, 13, B, C.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is

particularly useful for sensitive skin.

! This function may not be used in conjunction with wash cycles 8, 11, 12, 13, B, C.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle dura-

tion, this function offers a high-performance wash.

! This function may not be used in conjunction with wash cycles 5, 8, 9, 10, 11, 12, 13, A, B, C.

Table of Drying times (guideline values)

Fabric

type

Load type

Max.

load (kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton

Clothing of diffe-

rent sizes, Terry

towels

5 180 170 140

Synthe-

tics

Sheets, Shirts, Py-

jamas, socks, etc.

3 140 120 100

Wool

Knitwear, Pullo-

vers. etc.

1.5 150 140 120

Detergent dispenser drawer

Good washing results also depend on the correct dose

of detergent: adding too much detergent will not neces-

sarily result in a more efficient wash, and may in fact a

build up on the inside of your appliance and contribute

to environmental pollution.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or wa-

shing additive, as follows.

! Do not pour detergent into the middle compartment (*).

Detergent should only be poured into the compartment 1.

compartment 1: Detergent for the wash cycle (powder

or liquid)

For best results liquid detergent should be poured in

the dispenser immediately before the start of the pro-

gramme.

compartment 2: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whi-

tes.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Baby cycle: this wash cycle 6 can be used to remove the

soiling typically caused by babies, while ensuring that all

detergent is removed from nappies in order to prevent

the delicate skin of babies from suffering allergies.

The cycle has been designed to reduce the amount

of bacteria by using a greater quantity of water and

optimising the effect of special disinfecting additives

added to the detergent.

At the end of the wash cycle, the machine will slowly

rotate the drum to prevent the formation of creases;

to end the cycle press the START/PAUSE button.

Shirts: use special wash cycle 7 to wash shirts in various

fabrics and colours.

It guarantees maximum care is taken of the garments

and minimises the formation of creases.

Wool: all wool garments can be washed using programme

9, even those carrying the “hand-wash only” label.

For best results, use special detergents and do not

exceed 1,5 kg of laundry.

Silk: use special wash cycle 10 to wash all silk garments.

We recommend the use of special detergent which has

been designed to wash delicate clothes.

Curtains: fold curtains and place them in a pillow case

or mesh bag. Use wash cycle 10.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the drum

rotates continuously at a speed which is slightly greater

than the washing rotation speed. If, after several at-

tempts, the load is not balanced correctly, the machine

spins at a reduced spin speed. If the load is excessively

unbalanced, the Washer-dryer performs the distribution

process instead of spinning. To encourage improved load

distribution and balance, we recommend small and large

garments are mixed in the load.

Detergents and laundry

! This Washer-dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the applian-

ce by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

- Do not dry unwashed items in the tumble dryer.

- Items that have been soiled with substances such

as cooking oil, acetone, alcohol, petrol, kerosene, spot

removers, turpentine, waxes and wax removers should

be washed in hot water with an extra amount of de-

tergent before being dried in the tumble dryer.

- Items such as foam rubber (latex foam), shower

caps, waterproof textiles, rubber backed articles and

clothes or pillows fitted with foam rubber pads should

not be dried in the tumble dryer.

- Fabric softeners, or similar products, should be

used as specified by the fabric softener instructions.

- The final part of a tumble dryer cycle occurs without

heat (cool down cycle) to ensure that the items are

left at a temperature that ensures that the items will

not be damaged.

WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated.

• Do not touch the machine when barefoot or with wet

or damp hands or feet.

• Do not pull on the power supply cable when unplugging the

appliance from the electricity socket. Hold the plug and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extre-

mely high temperatures.

• Never force the porthole door. This could damage the safety

lock mechanism designed to prevent accidental opening.

• If the appliance breaks down, do not under any cir-

cumstances access the internal mechanisms in an

attempt to repair it yourself.

• Always keep children well away from the appliance

while it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the Washer-dryer, make

sure the drum is empty.

• During the drying phase, the door tends to get quite hot.

• Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

• Do not use the appliance to dry foam rubber or

similar elastomers.

• Make sure that the water tap is turned on during

the drying cycles.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected. Consumers should contact their local

authority or retailer for information concerning

the correct disposal of their old appliance.

Precautions and tips

Care and maintenance

Cutting off the water and electricity sup-

plies

• Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

Washer-dryer and help to prevent leaks.

• Unplug the Washer-dryer when cleaning it and during

all maintenance work.

Cleaning the Washer-dryer

The outer parts and rubber components of the ap-

pliance can be cleaned using a soft cloth soaked in lu-

kewarm soapy water. Do not use solvents or abrasives.

Cleaning the detergent dispenser drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated fre-

quently.

Caring for the door and drum of your ap-

pliance

• Always leave the porthole door ajar in order to pre-

vent unpleasant odours from forming.

Cleaning the pump

The Washer-dryer is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

pre-chamber which protects the pump, situated in its

bottom part.

! Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine (see

figure);

2. unscrew the lid by rota-

ting it anti-clockwise(see

figure): a little water may

trickle out. This is per-

fectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are secu-

rely in place before you push it onto the appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during the

wash cycles, water pressure is very strong and a cra-

cked hose could easily split open.

! Never use second-hand hoses.

Troubleshooting

Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure

that the problem cannot be solved easily using the following list.

Problem:

The machine does not switch on.

The wash cycle does not start.

The machine does not dry.

The clothes are too hot when the

drying cycle is finished.

The machine does not fill with water or

the indicator light for the first wash

cycle stage flashes rapidly.

The machine continuously fills with

water and continually drains away

or Water left in the drum

or Stuck on wash.

The machine does not drain or spin

(error lights flashing).

The wash programme takes too long.

The machine vibrates a lot during the

spin cycle.

The machine is noisy.

The machine wont spin properly.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make contact.

• There is no power to the socket, or the fuse has blown in the mains plug.

• The door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been turned on to allow water to flow into the machine.

• The ‘DELAY TIMER’ has been selected.

• Check the 2 sections above.

• The ‘DRY’ selector knob is in the position.

• A cooling-down period is always added to the end of each drying cycle. If

the clothes appear too hot to handle leave the door open to allow to cool

further before removing from the machine.

• The water inlet hose is kinked.

• The water inlet hose is not connected to the water supply.

• The water pressure is too low.

• The water tap has not been turned on to allow water to flow into the machine.

• There is no water supply to the house.

• The inlet valve filter is blocked.

• The START/PAUSE button has not been pressed.

• The top of the drain hose is too low - It must be fitted at a height between

65 and 100 cm from the floor (see “Installation”).

• The drain hose is connected incorrectly to the sink trap allowing water to

run into the machine, the drain hose must be positioned higher than the

bottom of the sink to prevent water flowing down the drain hose.

• The end of the drain hose has been pushed too far down the standpipe, the

‘U’ bracket should be fitted 100 mm from the end of the drain hose.

• The Pump filter is blocked - (see Care & Maintenance).

• The drain hose is kinked.

• New Installation - The blanking cap or spigot has not been removed if con-

nected under a sink.

• The drain hose or sink trap is blocked.

• Programme times will vary due to water pressure, the incoming water temperatu-

re and if the wash load goes out of balance. This will increase the programme time

accordingly (see ‘The machine wont spin properly’ below) - (Most Common Cause!).

• The feet have not been adjusted, enabling the machine to rock.

• New Installation - Either the Transit Bolts including the plastic spacers, or the

Polystyrene Packaging have not been removed when installing the machine.

• The machine is trapped between cabinets and/or walls.

• The load is in a slight out of balance condition and machine is spinning, but at a lower speed.

• There will always be some motor, pump and drum noise during spin.

• Out of Balance detected when attempting to go into a spin cycle - If this

happens the machine will continue to try to repeat the distribution of the

load required before the machine will go into higher spin speeds - This will

increase the programme time accordingly. This is a safety feature to pre-

vent damage. Out of Balance can be caused by washing a single heavy item

(eg duvet, quilt, etc). - Try the programme again using a different load.

The machine leaks from the

dispenser.

The machine leaks (other than dispenser).

The ‘START/PAUSE’ indicator light

illuminates Orange and the function

indicator lights flash rapidly.

The machine smells.

The machine door cannot be

opened.

Door Seal damaged at the bottom.

The water level is too low when the

machine is washing.

There is too much foam.

After completing the programme, or

before starting a programme, the ma-

chine has turned itself off (no lights).

General.

• The dispenser drawer is blocked with detergent and requires cleaning.

• The water pressure is too high and requires turning down - turn down the

tap on the water supply pipe slightly and try again.

• The machine is tilting forwards - It must be level when in its final position.

• The fill hose is loose, check both the cabinet and tap ends.

• The fill hose is tight but still leaks, if so replace the rubber washers, or the

fill hose is missing the rubber washer.

• The drain hose is not fixed in properly.

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again If the problem persists contact the Technical

Assistance Service.

• The machine requires a service wash. Run a 90 degree wash cycle with de-

tergent and no laundry.

• The door will not open until the door lock indicator light goes out shortly

after the program has finished.

• If there is no power to the machine you need to perform the manual unlo-

cking procedure (see Precautions & Tips).

• The door seal has drainage holes at the bottom - This is normal.

• The water level is correct if it can be seen at the bottom of the door.

• The detergent is not suitable for machine washing (it should display the text

‘for washing machines’ or ‘hand and machine wash’ or the like).

• Too much detergent was used - less detergent is required in soft water.

• To comply with new energy saving regulations the machine is fitted with an

automatic standby system. Press ‘ON/OFF’ button for 3 seconds to acti-

vate the machine, it can then either be switched off or a new programme

selected.

• Your washing machine contains sensors that monitor progress during the wash

cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/pro-

gress).

Normally, if your machine successfully completes the cycle, there is unlikely

to be anything wrong!

Remember, you will be charged for a service call for problems caused by incorrect installation, as listed above.

Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.

Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective

because of either workmanship or materials, we will, at our discretion, either repair or replace the

appliance at no cost to you.

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

- The appliance is used only on the electricity or gas supply printed on the rating plate.

- The appliance has been used for normal domestic purposes only.

- The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

- Any repair work must be undertaken by us or our appointed agent.

- Any parts removed during repair work or any appliance that is replaced become our property.

- The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

- Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

- Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

- Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL OR NON-

DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you

registering your appliance with us and the parts being fitted by one of our authorised engineers. There

will be a charge for our engineer’s time. To activate the extra parts warranty on your appliance, simply

call our registration line on 08448 24 24 24 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on

08448 226 226 (Republic of Ireland 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or,

where necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will

replace your machine or, if you prefer, give you your money back.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working life than

us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint’s continued commitment to helping the environment, Hotpoint reserves the right

to use quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer be plugged into a mains socket, and the door

cannot be locked shut.

195108581.00

11/2012 - Xerox Fabriano

Hotpoint Washer/Dryer WDL 540 P/G/A/K User manual

Brand: Hotpoint

Model: Washer/Dryer WDL 540 P/G/A/K

Category: Washing machines

Type: User manual

This manual is also suitable for

WDL 540 P/G/A/K

A range of wash cycles to choose from, including a quick wash cycle and a delicate cycle.
A drying function that allows you to dry your clothes in the same machine after washing them.
A range of temperature settings, so you can wash your clothes at the correct temperature for the fabric.
A range of spin speed settings, so you can choose the right spin speed for the type of fabric you are washing.

Download PDF

report

Hotpoint Washer/Dryer WDL 540 P/G/A/K User manual

This manual is also suitable for

Hotpoint Washer/Dryer WDL 540 P/G/A/K User manual

Related papers