PYLE Audio PLCD29 User manual

Brand
PYLE Audio
Model
PLCD29
Category
Car media receivers
Type
User manual
OWNER’S MANUAL
Mobile Audio System
• PLL Synthesizer Stereo Radio
• Digital Compact Disc Player
• Automatically Memory Storing
• Full Detachable Panel
• Auxiliary Input Function
PLCD29
2
Installation ............................................................................................... 3
DIN Front-Mount (Method A) ........................................................................... 3
Installing the unit ........................................................................................ 3
Removing the unit ...................................................................................... 4
DIN Rear-Mount (Method B) ............................................................................ 4
Using the Detachable Front Panel ................................................................... 5
Wiring Connection .................................................................................. 6
Operation ................................................................................................. 7
General Operation ............................................................................................ 7
Radio Operation ............................................................................................... 8
CD Operation ................................................................................................... 9
Specification ............................................................................................ 10
Trouble Shooting ..................................................................................... 11
CONTENTS
3
Notes:
• Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
• Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front” (conventional DIN Front-
mount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
DIN FRONT-MOUNT (Method A)
Installing the unit
1. Dashboard
2. Holder
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Screw
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap
can be bent by hand to the desired
angle.
7. Plain washer
30˚
(Fig. 1)
1
3
2
182
53
(Fig. 2)
1
2
6
5
4
3
7
INSTALLATION
4
Removing the unit
1. Frame
2. Insert fingers into the groove in the
front of frame and pull out to remove
the frame. (When reattaching the
frame, point the side with a groove
downwards and attach it.)
3. Lever
Insert the levers supplied with the unit
into the grooves at both sides of the
unit as shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the
sides of the unit.
Fastening the unit to the factory radio
mounting bracket.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become aligned
(are fitted), and tighten the screws at
2 places on each side.
Use either truss screws (5 x 6mm) or
flush surface screw (4 x 6mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
3. Factory radio mounting bracket
4. Dashboard or Console
5. Hook (Remove this part)
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
1
3
2
1
3
4
2
5
5
2
INSTALLATION
USING THE DETACHABLE FRONT PANEL
5
To Reinstall the Front Panel
1. Push the front panel into the main
body. A ‘click’ sound should be
heard.
2. Note that if the front panel fails to lock
in position properly, press control
button may not function and LCD
display may be missing some
segments. Pressing the release
button and then reinstall the front
panel again.
Precautions when Handling
1. Do not drop the front panel.
2. Do not put pressure on the display or
control buttons when detaching or
reinstalling the front panel.
3. Do not touch the contacts on the front
panel or on the main unit body. It may
result in poor electrical contact.
4. If any dirt or foreign substances
adhered on the contacts, they can be
removed with a clean and dry cloth.
5. Do not expose the front panel to high
temperatures or direct sunlight in
anywhere.
6. Keep away any volatile agents (e.g.
benzene, thinner, or insecticides) from
touching the surface of the front panel.
7. Do not attempt to disassemble the
front panel.
To Detach the Front Panel
1. Press the release button (REL), then
the right-hand side of the panel will
be ejected.
2. Remove the front panel by pulling its
right-hand side outward.
3. For safekeeping, store the front panel
in the supplied protective case
immediately after being removed.
Release
Button
Front Panel
Protective Case
Front Panel
6
WIRING CONNECTION
Note:
1. For 2-speakers system, green, violet, white/black and grey/black wire leads are
unconnected and isolated.
2. For 2-speakers system, keep the fader indicator at center position to maintain the
existing volume level.
WHITE
WHITE/BLACK
GREEN
GREEN/BLACK
Lch
SPK.
WHITE
GREEN/BLACK
GREY
GREY/BLACK
VIOLET
VIOLET/BLACK
ANTENNA CONNECTOR
RED
YELLOW
BLACK
CHOKE
BOX
BLUE
POWER
ANTENNA
GROUND (B–)
MEMORY
BACK-UP
IGNITION
SWITCH (B+)
4-SPEAKERS SYSTEM
4-SPEAKERS SYSTEM
FRONT
Lch SPK.
REAR
Lch SPK.
FRONT
Rch SPK.
REAR
Rch SPK.
2-SPEAKERS SYSTEM 2-SPEAKERS SYSTEM
Rch
SPK.
GREY
VIOLET/BLACK
MAIN UNIT
Rch RED
Lch WHITE
(GREY)
RCA CABLE
FUSE
88-C1280-11
7
OPERATION
GENERAL OPERATION
• ON/OFF
Press the PWR button (1) to turn on.
Press PWR again to turn it off.
• MUTE
Press the MUT button (3) to silence
the receiver. Press again to resume
listening.
• FACEPLATE RELEASE
Press REL button (5) to detach the
removable faceplate.
• LOUDNESS
Press LOU button (6) to increase bass
output and display will show “LOUD”.
• SET THE CLOCK
Press and hold the DSP button (7), the
clock will show on the display, then
press the TRACK/TUNE button (16)
to change minutes or TRACK/TUNE
button (15) to change hours.
• SELECT MODE
Press SEL button (9) to move display
through bass, treble, balance, fader
and volume functions.
25 26
2
1210119 1615 181 19 13 24
34 7
6
14 8 5
17
21222023
Use VOLUME (10) and VOLUME
(11) buttons to adjust the selected
mode. When mode has not been
adjusted for several seconds, display
returns to normal radio or CD display.
• SELECT LISTENING MODE
Press MOD button (13) to choose
desired listening mode.
(e.g. radio mode to CD mode to AUX
IN mode)
• LIQUID CRYSTAL DISPLAY
Exhibit current frequency and
activating functions on the display (14).
• AUXILIARY INPUT
The unit can be connected to a
portable audio player through this jack
(24).
• LED
When the front panel does not install
on the main unit, the LED indicator (25)
is flashing.
• RESET
Press RESET button (26) to re-initialize
the unit in case abnormalities or
malfunction is observed. When reset
is activated, all preset station/program
will be cleared. Reset button can be
access by any pointed material.
8
OPERATION
RADIO OPERATION
• SELECT BAND
Press BAND button (12) to change
between three FM bands and two AM
bands. Each band stores up to six
preset stations.
• SELECT STATIONS
Press TRACK/TUNE button (15) or
TRACK/TUNE button (16) shortly to
tune the frequency downward or
upward by step. Hold it for several
seconds to seek the previous or next
station.
• MONO/STEREO
Press MON button (4) to select
monaural or stereo (Mono reception
for radio stations). You can sometimes
improve reception of distant stations
by selecting mono operation.
• PRESET STATIONS
The six buttons (17) store and recall
stations for each band.
Store a station:
Select a band (12) and station, then
hold a preset button for several
seconds.
Recall a station:
Select a band (12), press a preset
button to select stored station.
• AUTOMATICALLY STORING &
PROGRAM SCANNING
Automatically Storing
Press and hold AMS button (18) for
several seconds to toggle
automatically storing function. It starts
searching next frequency and stores
the station into the preset memory.
At the end of automatically storing
operation, mode is changed to preset
scan.
BA TR B F V-
(Bass) (Treble) (Balance) (Fader) (Volume)
FM1 FM2 FM3 AM1 AM2
9
CD OPERATION
• DISC PLAY
Push a compact disc with the label
side facing up into the disc slot (2).
When there have correspondingly
showing on the display, press
button (19) to start playing with the first
track of the disc. The digital display
will indicate the track number and
playing time.
During the playing, press button
(19) to temporarily stop the playing.
Press EJECT button (8) to stop CD
play and eject CD from slot.
Receiver switches to radio operation.
• SELECT TRACKS
In CD operation, press TRACK/TUNE
button (15) or TRACK/TUNE button
(16) to move to the previous track or
the following track. Track number
shows on display.
In CD operation, hold TRACK/TUNE
button (15) or TRACK/TUNE button
(16) to fast reverse or fast forward.
CD play starts from when you release
the button.
• PLAY THE FIRST TRACK
Press TOP button (20) to play the first
track of the current disc.
• PREVIEW ALL TRACKS
In CD operation, press SCN button (22)
to play first several seconds of each
track on the current disc. Press it
again to stop intro and recover normal
playing.
• REPEAT THE SAME TRACK
In CD operation, press RPT button (21)
to continuously repeat the same track.
Press it again to stop repeat.
• PLAY ALL TRACKS
In CD operation, press RDM button
(23) to play all tracks on current disc in
random order. Press it again to cancel
the function.
OPERATION
Preset Scanning
Press AMS button (18) shortly to
toggle preset scanning function.
During the scanning, it will stop at
every stored station for several
seconds and the frequency of station
being scanned flashes on the display.
Press it again to stop scanning.
• DISPLAY
During radio operation, press the DSP
button (7) to recall the time display.
Press it again or activating any tuning
function, display will return to station
frequency read-out.
10
GENERAL
Power Supply Requirements : DC 12 Volts, Negative Ground
Chassis Dimensions : 178 (W) x 155 (D) x 50 (H)
Tone Controls
- Bass (at 100 Hz) : + 10 dB / – 10 dB
- Treble (at 10 KHz) : + 10 dB / – 10 dB
Maximum Output Power : 4 x 40 Watts (max.)
Current Drain : 5 Ampere (max.)
CD PLAYER
Signal to Noise Ratio : More than 60 dB
Channel Separation : More than 60 dB
Frequency Response : 20 Hz - 20 KHz
RADIO
FM
Frequency Coverage : 87.5 to 107.9 MHz
IF : 10.7 MHz
Sensitivity (S/N = 30 dB) : 3 µV
Stereo Separation : > 30 dB
AM
Frequency Coverage : 530 to 1710 KHz
IF : 450 KHz
Sensitivity (S/N = 20 dB) : 32 dBu
SPECIFICATION
11
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom Cause Solution
No power. The car ignition switch is If the power supply is properly
not on. connected to the car accessory
circuits, but the engine is not moving,
switch the ignition key to “ACC”.
The fuse is blown. Replace the fuse.
Disc cannot Presence of CD disc inside Remove the disc in the player, then
be loaded or the player. put a new one.
ejected.
Inserting the disc in Insert the compact disc with the
reverse direction. label facing upward.
Compact disc is extremely Clean the disc or try to play a new
dirty or defective disc. one.
Temperature inside the car Cool off or until the ambient
is too high. temperature return to normal.
Condensation. Leave the player off for an hour or
so, then try again.
No sound. Volume is in minimum. Adjust volume to a desired level.
Wiring is not properly Check wiring connection.
connected.
Sound skips. The installation angle is Adjust the installation angle to less
not more than 30 degrees. than 30 degrees.
The disc is extremely dirty Clean the compact disc, then try to
or defective disc. play a new one.
The operation The built-in microcomputer Press the RESET button.
keys do not is not operating properly Front panel is not properly fixed into
work. due to noise. its place.
The radio does The antenna cable is not Insert the antenna cable firmly.
not work. The connected.
radio station
automatic The signals are too weak. Select a station manually.
selection does
not work.
www.pyleaudio.com
88-C1280-11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

PYLE Audio PLCD29 User manual

Brand
PYLE Audio
Model
PLCD29
Category
Car media receivers
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents