Star Manufacturing SSG24 Operating instructions

Brand: Star Manufacturing

Model: SSG24

Type: Operating instructions

This manual is also suitable for

Installation and Operating Instructions

2M-Z6972 Rev. C 5/4/2006

STAR PROFESSIONAL

OUTDOOR GRILL

SSG Series

SSG48C

This symbol is intended to alert the user to the presence

of important operating and maintenance instructions in the

manual accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

The installer shall leave this instruction manual with the

grill for use by the end consumer.

NOTICE

Using any part other than genuine Star factory supplied parts relieves

the manufacturer of all liability.

Star reserves the right to change speciﬁ cations and product design

without notice. Such revisions do not entitle the buyer to correspond-

ing changes, improvements, additions or replacements for previously

purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the speciﬁ cations contained in this manual are subject to

change without notice. While Star Manufacturing exercises good faith

efforts to provide information that is accurate, we are not responsible for

errors or omissions in information provided or conclusions reached as

a result of using the speciﬁ cations. By using the information provided,

the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local dealer for service or required maintenance. For your convenience, you may contact the Star

Service Help Desk for questions and inquiries by telephone at 1-800-807-9054, by fax at 1-800-396-2677, or

by e-mail at [email protected]. Please have your model number and serial number for faster service.

PRODUCT INFORMATION

Enter the requested information below for easy reference.

Model Number Serial Number

Purchase Date Purchase Location

Installation Date Installer Name

Installer Phone Installer Address

SAFETY SYMBOL

Table of Contents

Safety Statements 5 - 7

General Information ...........................................................................................................................................5

Purchaser's Responsibility ................................................................................................................................5

California Proposition 65 Warning .....................................................................................................................6

Safety Practices to Avoid Injury .........................................................................................................................6

Additional Safety Statements ............................................................................................................................7

Propane Gas Usage 8 - 9

Propane (LP) Gas Warnings .............................................................................................................................8

Important Safety Information .............................................................................................................................8

LP Gas Cylinder Information .............................................................................................................................8

Overﬁ ll Protection Device (OPD) .......................................................................................................................9

BTU Delivery .....................................................................................................................................................9

LP Regulator Hose Assembly (Type 1) ..............................................................................................................9

Grill Installation 10 - 13

Locating the Grill ..............................................................................................................................................10

Access Considerations ....................................................................................................................................10

Built-In Placement ...........................................................................................................................................10

Electrical Requirements / Connection .............................................................................................................10

Clearance to Non-Combustibles ...................................................................................................................... 11

Clearance to Combustibles ............................................................................................................................. 11

Grill Head and Base Installation ......................................................................................................................12

Gas Requirements ...........................................................................................................................................12

Natural Gas Installation ...................................................................................................................................13

LP Gas Installation (Type 1 Regulator) ............................................................................................................13

Leak Testing ....................................................................................................................................................13

To Perform a Leak Test / To Fix a Leak ...........................................................................................................13

Grill Features 14 - 16

The Grill ...........................................................................................................................................................14

Grill Combo ......................................................................................................................................................15

Control Pod ......................................................................................................................................................15

Grill Burners .....................................................................................................................................................16

Grill Operation 17 - 23

Lighting the Grill ...............................................................................................................................................17

Match Lighting: Grill Burner ............................................................................................................................17

Smoker Burner ......................................................................................................................18

Infrared Broiler Burner ...........................................................................................................18

Side Burners ..........................................................................................................................18

Infrared Rotisserie Burner .....................................................................................................19

Burner Adjustments .........................................................................................................................................20

Control Valve Low Setting ...............................................................................................................................20

Using the Electronic Control Pod .....................................................................................................................20

Temperature Display ........................................................................................................................................21

Using the Electronic Timer ...............................................................................................................................21

Grill Surface Light ............................................................................................................................................22

Changing the Grill Light Bulb ...........................................................................................................................22

Locking the Casters .........................................................................................................................................22

End Shelves: Raising/Lowering ......................................................................................................................22

Power Panel ....................................................................................................................................................23

Cooking Features 24 - 26

Grill ..................................................................................................................................................................24

Smoker ............................................................................................................................................................24

Rotisserie .........................................................................................................................................................25

Menu Guide .....................................................................................................................................................26

Table of Contents

Care and Maintenance 27 - 29

Cleaning and Care of Your Grill .......................................................................................................................27

Ignitor Battery Replacement ............................................................................................................................29

Clearing Spider Webs and Nests ....................................................................................................................29

Grill Troubleshooting Guide 30

Warranty 31

Wiring Diagrams 32 - 33

Exploded Views and Parts Lists 34 - 51

Grill Body Removable Parts ............................................................................................................................34

Grill Body Service Parts ...................................................................................................................................36

Lower Grill Body Service Parts ........................................................................................................................38

Faceplate & Ignitor Wire Assembly ..................................................................................................................40

Manifold Assembly ...........................................................................................................................................42

Control Pod Assembly .....................................................................................................................................44

Side Burner / Island Assembly .........................................................................................................................46

Side Shelf Burner & Accessories Assembly ....................................................................................................48

Grill Bases Assembly .......................................................................................................................................50

Burner, Oriﬁ ce, and Ignitor Table 52

Notes 53 - 55

Read this installation operation manual thoroughly before attempting to operate

your Star Grill. Proper installation and servicing will ensure the long life of your grill.

Adherence to the safety statements in this manual will allow for safe and effective

operation.

IMPORTANT After unloading the crate containing your Star Grill, remove any plastic or

paper packing materials along with any tie-downs used to hold burners or

other items in place. It is essential that all plastic or paper protection and

packing materials be removed from the unit prior to lighting.

Before using your Star Grill, be sure to unpack all components such as the

skewer, meat prongs, mitts, electronic control pod, and grates. Be sure to

locate all radiant panels and grates on the unit before using.

It is the responsibility of the purchaser:

1. To read this installation manual completely before attempting to install, service,

or operate the Star Grill and to retain these instructions for future reference.

2. To see that gas and electric services for the grill are installed in accordance with

all applicable codes by a qualiﬁ ed installer of your choice.

3. To place the grill in a safe location as speciﬁ ed by this installation manual and

all applicable codes.

IMPORTANT Do not attempt to operate the grill until connection of utility service has

been fully inspected by an individual familiar with all local gas codes and

regulations.

CAUTION IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE, OR

MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY, OR DEATH. READ

ALL INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING

THIS EQUIPMENT.

TESTED IN ACCORDANCE WITH ANSI Z21.58b STANDARD FOR OUTDOOR COOKING GAS

APPLIANCES. THIS GRILL IS FOR OUTDOOR USE ONLY.

Check your local building codes for the proper method of installation. In the absence of local codes,

this unit should be installed in accordance with the National Fuel Gas Code No. Z223.1/NFPA 54 or

CAN/CGA-B149.1, Natural Gas and Propane Installation Code and the National Electrical Code ANSI/

NFPA No. 70 or the Canadian Electrical Code, CSA C22.1.

WARNING DO NOT TRY LIGHTING THIS APPLIANCE WITHOUT READING

THE "LIGHTING INSTRUCTIONS" SECTION OF THIS MANUAL.

Safety Statements

FOR YOUR SAFETY

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ﬂ ame.

3. Open hood.

4. If odor continues, immediately call your supplier

or your ﬁ re department.

PURCHASER'S

RESPONSIBILITY

GENERAL

INFORMATION

FOR YOUR SAFETY

1. Do not store or use gasoline or other ﬂ ammable

vapors and liquids in the vicinity of this or any other

appliance.

2. An LP cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

CAUTION Post in a prominent location the emergency telephone number of your local gas

supplier and instructions to be followed in the event you smell gas. If the smell

of gas is detected, immediately call the emergency phone number of your local

gas company. They will have personnel and provisions available to correct the

problem.

CAUTION THIS GRILL IS FOR OUTDOOR USE ONLY. DO NOT USE IN BUILDINGS,

GARAGES, SHEDS, OR OTHER TYPES OF ENCLOSED AREAS. DO

NOT USE ON A RECREATIONAL VEHICLE OR BOAT.

WARNING If not installed, operated, and maintained in accordance with the manu-facturer's

instructions, this product could expose you to substances in fuel or from fuel

combustion which can cause death or serious illness.

The burning of gas cooking fuel generates some by-products which are on the

list of substances which are known by the State of California to cause cancer or

reproductive harm. California law requires businesses to warn customers of potential

exposure to such substances. To minimize exposure to these substances, always

operate this unit according to the installation and operating instructions, ensuring

you provide good ventilation when cooking with gas.

When properly cared for, your grill will give safe, reliable service for many years.

However, extreme care must be used since the grill produces intense heat and can

increase accident potential. When using this appliance, basic safety practices must

be followed.

Read this instruction manual carefully and completely before using your grill to reduce

the risk of ﬁ re, burn hazard, or other injury. Begin by ensuring proper installation

and servicing. Do not repair or replace any part of the grill unless speciﬁ cally

recommended in this manual. All other service should be referred to a qualiﬁ ed

technician.

Always be sure to turn off all burners and the gas supply after using the grill. Do

not leave the grill unattended while grilling and do not allow children to play around

the grill or crawl inside the base.

For personal safety, wear proper apparel when grilling. Loose-ﬁ tting garments or

sleeves should never be worn while using this appliance. Some synthetic fabrics

are highly ﬂ ammable and should not be worn while cooking. Only certain types of

glass, heat-proof glass ceramic, earthenware, or other glazed utensils are suitable

for grill use. Using other types of materials may lead to breakage with sudden

temperature changes. Use only on low or medium heat settings according to the

manufacturer's directions.

CAUTION When lighting a burner, always pay close attention to the burner and electric

starter you are using. Do not turn on a burner and leave it on before pushing

the ignitor button since an excess of gas can build up in the grill.

Safety Statements

CALIFORNIA

PROPOSITION 65

WARNING

SAFETY

PRACTICES TO

AVOID INJURY

When heating or cooking, use a covered or protected hand when opening the grill

hood. Open the hood slowly to allow the heat to escape. Never lean over an open

grill or touch the grill rack, burner grate, hot skewer, or any surrounding areas near

the grill since they can be very hot and could cause serious burns. Always use the

grill mitts provided for handling the roasting spit or roasting pans. Keep the mitts

dry to avoid steam burns.

CAUTION GREASE IS FLAMMABLE. LET HOT GREASE COOL BEFORE

ATTEMPTING TO HANDLE IT.

Avoid grease deposit collection in the drip trays. The drip trays, grates, and grease

trough should be cleaned often with a wire brush. Excessive grease build-up can

lead to a grease ﬁ re. Always have the drip trays in place during operation.

Do not use aluminum foil to line the drip trays or grill racks. This can severely upset

combustion airﬂ ow or trap excessive heat in the control area. The result of this can

be melted knobs or damaged controls.

Always keep the grill clean. This includes all burners, radiants, grates, drip trays,

and the grease trough. The burners can be easily removed by removing the grate,

the radiant panel, the burner hold down bracket, and then the burner. Be sure all

the burner parts are open and free of any food particles or residue. Do not clean

the grill while it is hot to avoid burns.

CAUTION Some spiders and insects can nest in the burners and oriﬁ ce ﬁ ttings. Some

will make small webs across oriﬁ ces, thereby affecting the proper ﬂ ow of gas

to the burner or causing the gas to burn back into the control compartment.

This can be a dangerous condition which could damage the grill controls or

make it unsafe to operate. Be sure to periodically inspect burners and oriﬁ ces

for this condition.

This grill is designed for use with the gas speciﬁ ed on the nameplate on the underside

of the front panel. Do not use charcoal or charcoal lighter with this grill.

If this grill is kept indoors for storage, detach and leave the LP cylinder outdoors.

Do not operate this grill under unprotected combustible construction. Use only in

well-ventilated areas, but do not use in a windy location. Do not operate the grill

directly under overhanging tree branches.

The grill requires a 120 VAC grounded supply for powering the electronic temperature

readout or the rotisserie motor. Be sure to safely route any power cord to the

base or provide easy access to the power cord connection for built-in models.

Do not operate the unit in the rain or snow with an exposed extension cord.

Keep all ventilation openings to the base and unit bottom free for proper ventilation

and maintain all clearance spacings. Maintain minimum clearance from the sides

and back of the grill to adjacent combustible construction 8 inches from the sides

and 12 inches from the back.

Safety Statements

ADDITIONAL

SAFETY

STATEMENTS

1. Know the odor of LP gas. If you hear, see, or smell leaking LP gas, immediately

get everyone away from the cylinder and call the ﬁ re department. Do not attempt

any repairs.

2. LP gas is heavier than air and may settle in low places while dissipating.

3. Contact with the liquid contents of a cylinder will cause freeze burns to the skin.

4. Do not allow children to tamper or play with a cylinder.

5. When not connected for use, keep the cylinder valve turned off.

6. Do not use, store, or transport a cylinder where it could be exposed to high

temperatures. The relief valve may open allowing a large amount of ﬂ ammable

gas to escape.

7. When transporting, keep the cylinder secured in an upright position with the

cylinder valve turned off.

8. CAUTION: The type 1 pressure regulator and connector provided with this outdoor

cooking gas appliance must be used. The regulator is set for an outlet pressure

of 11 inches water column.

9. The cylinder supply system must be arranged for vapor withdrawal and include

a collar to protect the cylinder valve.

10. The gas supply must be turned off at the LP gas supply cylinder when the grill is

not in use.

Certain liquid propane dealers may ﬁ ll liquid propane cylinders for grill use beyond

cylinder ﬁ lling capacity. "Overﬁ lling" may create a dangerous condition.

"Overﬁ lled" tanks can build up excess pressure. As a safety device, the tank's pressure

relief valve will vent propane gas vapor to relieve this excess pressure. This vapor

is combustible and therefore can be ignited.

To reduce this danger, you should take the following safety precautions:

1. When you have your tank ﬁ lled, be sure you tell the supplier to ﬁ ll it to no more

than 80% of its total capacity.

2. If you own or use an extra spare tank or have a disconnected tank, you should

NEVER store it near or under the grill unit or heat box or near any other ignition

or heat source.

3. Failure to follow these instructions may cause ﬁ re, serious injury, or death.

The LP gas supply cylinder to be used must be constructed and marked in accordance

with the speciﬁ cations for LP gas cylinders of the U.S. Department of Transportation

(DOT) or the National Standard of Canada, CAN/CSA-B339, Cylinders, Spheres and

Tubes for the Transportation of Dangerous Goods.

WARNING Inspect the fuel supply hose before each use of the grill. The hose can be

accessed by opening the front door on the grill base. If it is evident there is

excessive abrasion, wear, or the hose is cut, it must be replaced prior to the

grill being put into operation. Contact your dealer to obtain a replacement fuel

supply hose. Keep the ventilation openings of the cylinder enclosure free and

clear from debris.

If the grill is not in use, the gas must be turned off at the supply cylinder.

PROPANE

(LP) GAS

WARNINGS

LP GAS

CYLINDER

INFORMATION

Propane Gas Usage

IMPORTANT

SAFETY

INFORMATION

WARNING Do not store a second 20 pound propane cylinder within the Star Grill base. The

base is designed for the use and storage of one 20 pound propane cylinder.

Storage of an outdoor cooking gas appliance indoors is permissible only if the cylinder

is disconnected and removed from the grill. Cylinders must be stored outdoors, out

of reach of children, and must not be stored in a building, garage, or any enclosed

area.

The Overﬁ ll Protection Device (OPD) will help reduce the potential for the overﬁ lling

of the propane cylinder, thus reducing the possibility of hydrostatic relief valve

discharges. This gas grill must be connected to an LP gas cylinder incorporating

an overﬁ ll protection device.

BTU DELIVERY The OPD valve has a size 56 oriﬁ ce through which the propane is released for

consumption. Depending on the propane's temperature and pressure, the release

from the cylinder is approximately 125,000 Btu/hour.

The pressure regulator and hose assembly supplied with the grill must be used.

A replacement pressure regulator and hose assembly for the grill can be obtained

by contacting your dealer. This device includes a user-friendly swivel nut, thermal

element, and listed excess ﬂ ow valve. This connection incorporates a thermal

sensing device that will shut off the ﬂ ow of gas when it is exposed to temperatures

in the range of 240°F to 300°F.

The excess ﬂ ow valve is designed to limit the ﬂ ow of LP gas from the container in

the event the connection ﬁ tting, regulator, or hose is broken between the container

valve and the appliance. This device does not stop the ﬂ ow of gas but will limit

the rate of gas ﬂ ow to 10 scfh or less. This device is designed to shut off when it

senses the gas ﬂ ow is in excess of 100,000 Btu/hr for black nuts and 200,000 Btu/hr

for green nuts. This sensitivity will cause the device to activate when the cylinder

valve is opened but will automatically reset within a few seconds as long as there

is no gas leak and all valves have been turned off.

The following steps should be taken each time the cylinder is turned on or it is

determined that the excess ﬂ ow device has been activated (trouble lighting burners,

low ﬂ ame, or low heat):

1. Be sure all valves are turned off, including pilot lights if equipped, prior to turning

the cylinder valve to the on position.

2. Turn the cylinder valve on slowly to reduce gas surging (slamming the excess

ﬂ ow device shut); this will reduce the automatic reset time.

3. Leak test all connections with a bubble solution or non-ammonia soapy water

solution. If a leak is present, the solution will "bubble" at the leak point that

indicates a repair is needed.

4. Allow a minimum of 10 seconds for the excess ﬂ ow device to automatically reset

prior to operating any of the grill burners.

5. If the grill continues to operate improperly, check that the cylinder has gas or

contact a qualiﬁ ed service technician.

Propane Gas Usage

OVERFILL

PROTECTION

DEVICE (OPD)

LP REGULATOR

HOSE ASSEMBLY

(TYPE 1)

Grill Installation

Your new Star Grill can be located in a Star Grill base (model series 24SSB, 30SSB,

36SSB, or 48SSB) or can be installed into an immovable masonry enclosure. When

selecting a suitable location for your grill, take into account concerns such as wind

exposure and areas of high trafﬁ c. Do not locate the grill close to a home or any

kind of combustible construction. Do not locate overhead shading umbrellas or other

combustible items near or above the grill. Grill exhaust can be very hot and under

extreme conditions can emit ﬂ ames. Maintain an open area around the grill and

enclosure at all times, keeping the area free from combustible materials, gasoline,

and other ﬂ ammable vapors and liquids. Be sure your grill is located on a level

surface. Keep any electrical supply cord and the fuel supply hose away from all

heated surfaces.

The gas valve and electrical outlet should be placed in a convenient location to

allow easy access for any service visits. This access should make any necessary

service quicker and less disruptive and allow easier disconnection of electricity and

gas for cleaning around and behind the grill.

The Star Grill is designed for easy placement into an immovable masonry enclosure.

Non-combustible masonry materials are recommended for such installations and

the proper dimensions should be used to provide proper support for the grill. All

clearance locations and ventilation requirements apply whether the grill is used with

a Star Grill base or placed into an immovable masonry enclosure. The following

guidelines must be kept in mind:

1. Do not build your immovable masonry enclosure under unprotected construction

such as awnings or gutters.

2. Do not build under trees, bushes, or shrubs.

3. Your masonry enclosure must take into account all necessary clearances for

gas and electrical lines.

4. Provide ventilation openings in your enclosure to allow for ventilation and detection

of gas leaks. (Recommendation: 25in

or more free area near the enclosure

bottom on the gas connection side.) Do not obstruct the ﬂ ow of combustion or

ventilation air.

The Star Grill base can have a built-in electrical box with a GFCI receptacle. Deluxe

models come with this option. A power supply cord can be attached at the box

connector, thereby providing power to the grill head and base. The unit operates

on 120 VAC supply and will normally draw less than 1 amp of current.

For built-in models, hard wiring to a junction box must be performed by a qualiﬁ ed

installer per the National Electrical Code. Maintain the junction box within a distance

of 3 feet from the grill where the power cord exits. The 3-prong cord measures

approximately 40 inches in length. An easily accessible ON/OFF gas valve should

also be provided in this lower enclosure.

Before making any electrical connections to this unit, check that the power supply

is adequate for the voltage, amperage, and phase requirements stated on the

speciﬁ cation plate.

LOCATING

THE GRILL

ACCESS

CONSIDERATIONS

BUILT-IN

PLACEMENT

ELECTRICAL

REQUIREMENTS

ELECTRICAL

CONNECTION

Grill Installation

Non-Combustible

Enclosure

Model "A" Dimension

SSG24 22

SSG30 28

SSG36/36C 34

SSG48/48C 46

Combustible

Enclosure Using

Insulated Jacket

Model "A" Dimension

SSG24 28

SSG30 34

SSG36/36C 40

SSG48/48C 52

Maintain a 3" space from the back of the grill for service access and cleaning. The

grill exhausts to the top back of the unit, which may result in occasional grease

build-up. Always consider cleaning and service accessibility when locating the

grill. The right side of the unit must have at least 8" of space above the grill for the

electronic temperature sensing pod. The left side may have zero clearance as may

the lower mounting enclosure.

A minimum of 12" from the back of the unit to combustible construction and 8" from

the sides of the unit to combustible construction must be provided.

The grill may be placed in a combustible enclosure only when used with an insulating

jacket around the grill. The jacket must be supported on its bottom. See cut-out

dimensions for the correct dimensions using the insulated jacket. Use only the Star

Manufacturing supplied jacket for this installation.

CLEARANCE

TO NON-

COMBUSTIBLES

CLEARANCE TO

COMBUSTIBLES

3“ TO

NON-COMBUSTIBLE

CONSTRUCTION

12" TO COMBUSTIBLE

CONSTRUCTION

8" TO COMBUSTIBLE

CONSTRUCTION

THE GRILL CAN BE PLACED DIRECTLY ADJACENT TO NON-COMBUSTIBLE CONSTRUCTION BELOW THE COOKING SURFACE.

36 [91.4cm]

25 1/8 [63.8cm]

5 [12.7cm]

12 1/2 [31.7cm]

9 [22.9cm]

20 [50.8cm]

3 [7.6cm]

26 1/8 [66.3cm]

WHE

N US

ING INSULATED SPACER JACKET

10 [25.4cm] WHEN USING

INSULATED JACKET

15 [38.1cm]

12 5/8 [32.1cm]

HOTPLATE-SIDE BURNER

MIN. SPACING

NOTE: 15" MINIMUM SPACING FOR

HOTPLATE-SIDE BURNER ON RIGHT

SIDE OF GRILL

HOTPLATE SPACING TO BE 4" MINIMUM

ON LEFT SIDE OF GRILL.

GRILL

Grill Installation

CAUTION DO NOT INSTALL THIS UNIT INTO A COMBUSTIBLE ENCLOSURE

WITHOUT AN INSULATED JACKET. THIS COULD RESULT IN A FIRE,

PROPERTY DAMAGE, OR PERSONAL INJURY.

1. Remove the base from the pallet

by removing the screws holding the

packing brackets.

2. Place the base near the grill head and

lock the casters.

3. Remove all loose items from the

grill.

4. Lift the grill head and place it into the

base making sure to lower and slide

it back evenly on both sides to keep

it from binding. (NOTE: Make sure

to place the cordset and/or gas hose

into the base in an area where it will

not be sitting on top of a wall or getting

pinched by the grill.)

5. Remove the two upper control panel

screws and replace them with the two

1-inch hex head screws supplied with

the base. (NOTE: The head must be

secured to the base with these screws

before operation.)

CAUTION THE GRILL MUST BE PLACED ON A LEVEL SURFACE AND THE CASTERS MUST

BE LOCKED WHILE OPERATING THE GRILL TO PREVENT MOVEMENT.

Verify that the unit nameplate marking on the upper front panel matches the type of

gas you are using. An installer-supplied gas shut-off valve must be installed in an

easily accessible location. All installer-supplied parts must conform to all local codes

or, in the absence of local codes, with the National Electrical Code ANSI/NFPA 70

and the National Fuel Gas Code No. Z223.1/NFPA 54. All pipe sealants must be

an approved type and resistant to the actions of LP gas. Do not use pipe sealant

on ﬂ are ﬁ ttings.

Total Btu requirements for the grill with all burners on HI are:

Model Btu Model Btu

SSG24 62,000 SSG30 72,000

SSG36 88,000 SSG36C 102,000

SSG48 119,000 SSG48C 128,000

The appliance, shut-off valve, and regulator must be disconnected from the gas

supply system during any pressure testing in excess of 1/2 PSIG. The appliance

must be isolated from the gas supply piping system by closing its individual manual

shut-off valve during any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 PSIG (3.5 kPa).

GRILL HEAD

AND BASE

INSTALLATION

GAS

REQUIREMENTS

The grill has a 1/2 NPT female connector at the rear left side of the grill bottom. Use

the 5" water column natural gas regulator supplied and a short nipple to connect to

the manifold inlet pipe. A natural gas supply line can then be attached to the inlet

side of the regulator. Supply pressure must be between 5" and 14" water column.

Be sure the installation is made by a qualiﬁ ed service technician knowledgable in

all local codes and the National Fuel Gas Code ANSI Z223.1/NFPA 54.

Grills set for LP gas will come with a 1/2" male x 3/8" ﬂ are connector and a type 1

hose/regulator assembly for connection to a standard 20 pound type 1 LP cylinder.

The tank is not included but may be available from your dealer.

The hose/regulator assembly is set for 11" water column. Be sure the tank valve is

closed and then attach the regulator and connector to the tank valve ﬁ tting. Turn

the green coupler clockwise until tight, but be careful to not overtighten the coupler.

Be sure all control knobs are turned OFF and read the lighting instructions carefully

before using the grill. Open the hood. If you do not plan to use the grill, disconnect

the regulator coupling from the tank by slowly turning it counterclockwise.

LEAK TESTING The manifold and all gas connections are factory tested, but a complete leak check

should be performed at the ﬁ nal installation due to possible rough handling during

shipping or some other unknown occurrence. Never operate your grill if the smell

of gas is present.

CAUTION DO NOT USE AN OPEN FLAME OR OTHER IGNITION SOURCE WHILE

PERFORMING A LEAK TEST. DO NOT SMOKE WHILE PERFORMING THIS

TEST. AN EXPLOSION OR FIRE MAY OCCUR.

1. Be sure all power to the unit is turned OFF.

2. Make a soapy solution of equal parts mild dishwashing detergent and water.

3. Slowly turn on the gas fuel supply by turning the knob counterclockwise or the

natural gas supply valve on.

4. Using a small brush or squirt bottle, generously apply the water/soap solution

to all connections and ﬁ ttings.

5. If growing bubbles appear on any of the connections, you have a gas

leak. Immediately close the gas supply control valve by turning the handle

clockwise.

1. Slowly turn on the gas fuel supply by turning the knob counterclockwise or the

natural gas supply valve on.

2. Turn the control knob to the LITE position for several seconds to release any

gas pressure in the system.

3. Wash/clean off all remaining soap solution and tighten any leaking joints. Faulty

parts will need to be replaced. Use only factory-supplied or recommended parts.

If the cylinder valve is leaking, do not attempt to repair it but instead replace the

entire cylinder.

Grill Installation

NATURAL GAS

INSTALLATION

LP GAS

INSTALLATION

(

TYPE 1 REGULATOR)

TO PERFORM

A LEAK TEST

TO FIX A LEAK

Grill Features

THE GRILL Each grill section consists of an oversized stainless steel burner, a high-performance

radiant panel, and a multi-functional stainless steel grate. Models SSG30 and

larger provide a high-performance infrared broiler burner for the searing of low-fat

meats such as lean cuts of steaks and chops. This broiler burner will provide high

temperature radiant heat to the grates, searing faster than the standard burner.

Your new grill features a back infrared rotisserie burner that can be used to cook

meats on the skewer and meat prongs provided. It also features a built-in rotisserie

drive with a front-mounted power switch. All grills come with a smoker box and

separate smoker burner for smoking your select meats.

The grill features an electronic temperature sensing control pod with the following

features:

1. Bright digital temperature display of grill during operation.

2. Temperature display of meats being cooked using the meat probe.

3. Grill light for cooking at night.

4. Timer control for both count-down and count-up use.

1. Control Pod

2. Halogen Light

3. Control Pod Mounting Knob

4. Warming Rack

5. Rotisserie Skewer Rod

6. Rotisserie Power Switch

7. Grill Burner Ignitor Button

8. Smoker Box

9. Grill Drip Trays

10. Control Knobs

11. Radiant Burner Ignitor Button

12. Grates

Grill Features

1. Side Burners

2. Side Burner Ignitor Button

3. Rear Side Burner Control Knob

4. Front Side Burner Control Knob

5. Side Burner Drip Tray

6. Grill Drip Trays

7. Smoker Box

8. Grill Burner Ignitor Button

GRILL COMBO

1. Halogen Light

2. Light Power Switch

3. Time Display

4. Temperature Display

5. Meat Probe

6. Temperature Toggles

7. Timer Start/Stop

CONTROL POD

Grill Features

1. Infrared Rotisserie Burner

2. Infrared Broiler Burner

3. Grill Burner

4. Smoker Box

5. Grates

GRILL BURNERS

Grill Operation

CAUTION DO NOT TURN ON ALL THE GRILL/SEARING BURNERS AND LEAVE THE

HOOD CLOSED FOR MORE THAN 20 MINUTES. EXCESS HEAT CAN BUILD

UP INSIDE THE GRILL. OPENING THE HOOD WITH AN UNPROTECTED HAND

OR ARM CAN LEAD TO BURNS CAUSED BY THE RELEASE OF THIS HEAT.

Before attempting to light your grill, check the following:

1. Turn OFF the tank supply gas to the unit. Do not use the grill if you smell

gas.

2. Be sure the drip trays are in place.

3. Open the hood.

4. Be sure the LP tank connections to the manifold and tank are tight. Inspect

the hose for wear or abrasions. A damaged hose/regulator assembly must be

replaced. If using LP gas, make sure there is fuel in the LP cylinder.

5. Make sure all control knobs are turned to the OFF position.

6. Check that all grates and radiant panels are in place.

7. Do not lean over the grill or place your hands down inside the grill while attempting

to light it.

CAUTION BEFORE LIGHTING, BE SURE TO LOOK AT THE FRONT PANEL AND NOTE

THE APPROPRIATE IGNITOR BUTTON FOR THE BURNER YOU INTEND TO

LIGHT.

To light, turn ON the tank supply gas. Turn the control knob counterclockwise to

the HI/LITE position and push the correct ignitor button. You should hear a series

of sparks and the burner should light within 5 seconds. You should be able to see

a spark at the ignitor collector box just above the burner. If the burner fails to light,

turn the knob OFF and wait 5 minutes for gas to dissipate before attempting to light

again. If the burner fails to light after several attempts, it can be lit with a match.

Grill Burner:

Make sure all knobs are in the OFF position. Move the grate just above the burner

you intend to light. Turn the control knob for that burner to the HI/LITE position and,

with a lit match, place the ﬂ ame at the small hole of the long notch in the radiant

panel. The burner should light within several seconds. All burners may be lit with

a paperbook match, but for ease of lighting a long-stemmed match or butane lighter

(as shown) is recommended. Locate the lit match/lighter as shown.

LIGHTING

THE GRILL

MATCH LIGHTING

THE GRILL

Grill Operation

Smoker Burner:

The same method used for the grill burner can be used for lighting the smoker

burner. However, the smoker tray should be removed ﬁ rst, exposing the burner

ports. Light the smoker burner near the electrode at the front ports.

MATCH LIGHTING

THE GRILL

(continued)

Infrared Broiler Burner:

Use the same method to light the infrared broiler burner, locating the lit match at

the front corner as shown.

Side Burners:

The two side burners can also be lit using the same method. Locate the lit match

through the low grate support and near the burner ports.

Grill Operation

Infrared Rotisserie Burner:

Turn the knob to the HI/LITE position and push it in toward the front panel. Push

the ignitor button. You should see a spark at the back rotisserie electrodes. After

burner ignition, continue to push the knob in for approximately 30 seconds until

the rear burner begins to glow a dull red. You can then release the knob and the

thermocouple safety should keep the burner lit. If the burner fails to light, turn the

knob to the OFF position and wait 5 minutes before trying again.

For match lighting repeat the same steps with the rotisserie knob, turning to the

HI/LITE position and pushing in. Place the burning end of the lit match to the lower

left side of the rear infrared burner and ignition should occur immediately.

MATCH LIGHTING

THE GRILL

(continued)

CAUTION THE LOCATION OF THE INFRARED ROTISSERIE BURNER MAKES IT VERY

SUSCEPTIBLE TO STRONG WIND CONDITIONS. YOU SHOULD NOT OPERATE

THIS BURNER ON WINDY DAYS.

CAUTION IF ANY BURNER FAILS TO LIGHT USING A PROVIDED FLAME SUCH AS A

MATCH (GAS IS BEING SUPPLIED AND YOU DO NOT HAVE AN EMPTY TANK),

TURN OFF THE GAS SUPPLY AND CHECK THE BURNER FOR SPIDER WEBS

OR OTHER GAS OBSTRUCTIONS. IF NOTHING IS FOUND, CALL YOUR

DEALER.

Match lighting using a small paperbook match is possible (as illustrated below), but

it is recommended that you use a long-stemmed match or a butane lighter

Grill Operation

Prior to adjusting burners, observe the appearance of the burner ﬂ ame with the

burner set on HI. Flame height should be approximately 1-1/4" high with a blue

ﬂ ame. If your ﬂ ame meets these criteria, you probably do not need to adjust your

burner. If you have a yellow or uneven ﬂ ame then adjustment may be necessary.

NOTE: Burner ﬂ ames can sometimes be difﬁ cult to see in sunlight and should be

checked under shade or low light conditions.

Be sure the grill is turned OFF and cool before performing any burner adjustment.

Your burner has been factory set, but due to variations in gas it may, at times, be

necessary to adjust the burner air shutter setting. This can be done by removing

the top grates and carefully lifting off the radiant panels. The rear burner hold down

bracket can then be removed by unscrewing the two end screws holding it in place.

Carefully lift up the bracket and easily lift one of the burners up and out. For soft

or yellow ﬂ ames, unscrew the air shutter hold down screw and open the air shutter

about 1/8 - 3/16" more. For a hard or noisy, lifting ﬂ ame, close the air shutter slightly.

Tighten the adjustment screw and carefully reposition the burner onto the oriﬁ ce and

into its rear burner support bracket. Turn on and test the burner to verify the ﬂ ame

ignition and performance. If acceptable, repeat the steps on the other burners.

After adjustment, be sure to relocate the hold down bracket and attach the screws.

Reinstall the radiant panels and grates. There is no air adjustment on the back

infrared burner or the front infrared broiler burner. The same adjustments can be

carried out for the side burners.

The burner control valves have a low burner setting for slower cooking of food items.

This setting has been pre-set at the factory and should not need adjustment.

1. Insert the control post into the control mount and tighten the mounting knob.

(NOTE: The slot in the bottom of the post must align with the pin in the post

mount.)

2. Attach the wire connector to the control mount.

3. Press the ON/OFF button to turn it on.

CAUTION DO NOT OVER-TIGHTEN THE ELECTRONIC CONTROL POD WIRE

CONNECTOR. IT SHOULD BE TIGHTENED ONLY UNTIL SNUG.

BURNER

ADJUSTMENTS

CONTROL VALVE

LOW SETTING

USING THE

ELECTRONIC

CONTROL POD

Page is loading ...

Star Manufacturing SSG24 Operating instructions

Brand: Star Manufacturing

Model: SSG24

Type: Operating instructions

This manual is also suitable for

Download PDF

report

Star Manufacturing SSG24 Operating instructions

This manual is also suitable for

Star Manufacturing SSG24 Operating instructions

Related papers

Other documents