AbleNet Linkable User guide

Linkable
AbleNet
Brand
AbleNet
Model
Linkable
Type
User guide

This manual is also suitable for

AbleNet Linkable wireless receivers and switch latch and timer (SLAT) provide versatile control options for individuals with limited mobility. With up to 8 transmitters linkable to a single receiver, users can operate multiple devices or appliances from various locations. The device features multiple modes of control, including direct mode for traditional switch behavior, timed modes for controlling device activation duration, and latch mode for toggle functionality. The built-in timer allows for precise control of device operation, ranging from 1 second to 60 minutes.

AbleNet Linkable wireless receivers and switch latch and timer (SLAT) provide versatile control options for individuals with limited mobility. With up to 8 transmitters linkable to a single receiver, users can operate multiple devices or appliances from various locations. The device features multiple modes of control, including direct mode for traditional switch behavior, timed modes for controlling device activation duration, and latch mode for toggle functionality. The built-in timer allows for precise control of device operation, ranging from 1 second to 60 minutes.

2
Link Receiver & Transmitter
1
3
Insert Batteries and Turn On
Connect Receiver & Activate Wireless Switch Latch & Timer (SLAT) Tricks, Tips, and Warranty
Insert two AA batteries into Receiver as shown on housing.
Slide the power switch to the “On” position. The Receiver’s light(s)
will activate briefly.
When batteries are low, the device’s light will flash three (3) times.
Select your Mode of Control by repeatedly pressing the “Mode” but-
ton. The Receiver’s lights will indicate which mode is activated. For
Timed Modes - Adjust the Timer Dial from 1-60 seconds or minutes
as desired.*
Modes of Control
Direct Traditional switch behavior - device remains
ON as long as switch is held.
Timed Seconds Runs device from 1 to 60 seconds with each
activation.
Timed Minutes Runs device from 1 to 60 minutes with each
activation.
Latch First activation turns device ON; second
activation turns it OFF.
*PROGRAMMING TIP: Turn the Timer Dial all the way up to 60 and
activate the device. As the desired time approaches, turn the Dial
back down towards 0, stopping the device at the time desired. The
first half-turn of the Timer Dial ranges from 1-10 sec./min. The
second half-turn ranges from 11-60 sec./min.
Your Receiver has slots on the bottom of the device for mounting
with Velcro® straps. For additional mounting options, visit
www.ablenetinc.com.
You can link up to 8 Transmitters to a Receiver using the linkable
method explained in Step 2. When a Receiver’s light is green, any
activated Transmitter will be linked. One Transmitter can also be
linked to multiple Receivers at the same time.
To unlink devices, press and hold the Receiver’s “Test” or “Mode”
button for more than 10 seconds.
To clean, wipe surfaces with a slightly damp cloth.
Warranty Information
AbleNet manufactured products include a two-year limited war-
ranty. This warranty is against defects in materials and manu-
facturing for two-years from the date of purchase. Warranty in
full text, along with return/repair information is available at www.
ablenetinc.com. For more information on AbleNet products and
services, contact:
AbleNet, Inc.
Minneapolis/St. Paul, MN | 800-322-0956 | www.ablenetinc.com
Plug the Receiver into any switch-accessible device or computer
switch interface.
Activate the Transmitter.
The Transmitter and Receiver will light red and the attached device
will activate.
NOTE: To test the physical connection with a switch-adapted
device, press and hold the “Test” or “Mode” button for 2 seconds.
1. With wireless Transmitter and Receiver turned on, press and
hold the Receiver’s “Test” or “Mode” button until the light turns
green (about 5 seconds).
2. Activate any Transmitter. The Receiver’s light will flash red 1
time when a link has been established.
*Link additional Transmitters by activating them now (optional).
3. Press and release the Receiver’s “Test” or “Mode” button to exit
linking mode.
Press & Hold
5 seconds
Press &
Release
On
Quickstart Guide:
Linkable
™
Wireless Receivers and
Wireless Switch Latch and Timer (SLAT)
www.ablenetinc.com
700-05475A (07/09)
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

AbleNet Linkable User guide

Linkable
AbleNet
Brand
AbleNet
Model
Linkable
Type
User guide
This manual is also suitable for

AbleNet Linkable wireless receivers and switch latch and timer (SLAT) provide versatile control options for individuals with limited mobility. With up to 8 transmitters linkable to a single receiver, users can operate multiple devices or appliances from various locations. The device features multiple modes of control, including direct mode for traditional switch behavior, timed modes for controlling device activation duration, and latch mode for toggle functionality. The built-in timer allows for precise control of device operation, ranging from 1 second to 60 minutes.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents