Little GIANT 550521 Installation guide

Little GIANT
Brand
Little GIANT
Model
550521
Type
Installation guide

This manual is also suitable for

INTRODUCTION
EN
The shallow pan condensate unit is designed especially for ceiling-mounted units
and other refrigerated air conditioners where minimum height is important. The
pump is designed to be placed directly into a holding reservoir or used with a tank
supplied by the manufacturer. Do not use the pump where the water level can
exceed the holding reservoir capacity. The pump is controlled by a float/switch
mechanism that automatically switches the pump on and off.
This instruction sheet primarily covers the standard models in this pump series, but
is applicable to other models in this series not listed by model number. If the model
number of your pump is not listed, use caution when ordering replacement parts.
Always give the model number of your pump when ordering replacement parts.
Read these instructions carefully. Failure to follow these instructions voids all warranty,
and could result in bodily harm or property damage. All wiring and plumbing must
be permanent, and comply with local, state, and national electrical codes. Shut off
electrical power at the fuse box before servicing the pump.
INSTALLATION
1. Carefully unpack the pump. Remove the cardboard packing from the motor
cover air slots. Carefully slide the packing away from the pump. This packing is
used to prevent switch movement during shipment.
2. This model can be equipped with a reservoir tank, which is sold separately. The
tank has two holes provided to mount the unit in a convenient location. The
pump must be level and the inlet must be below the coil drain.
PIPING
1. Run flexible tubing or pipe from evaporator drain into pump holding tank. Be
sure inlet piping is sloped downward to allow gravity flow.
2. The outlet piping (Figure 1) should be flexible tubing or pipe (1/2” I.D. maximum
to prevent excessive flow back to unit). From condensate unit, extend discharge
piping straight up as high as necessary (but not above the head/GPH of the model
being installed.) From this high point, slope discharge line down slightly to a point
above drain area, then turn down and extend to a point below or approximately
level with the bottom of the condensate unit. This will give a siphoning effect which
will improve efficiency of the condensate unit. If it is not possible to slope discharge
line down, make an inverted “U” trap directly above the pump at the highest point.
ELECTRICAL CONNECTIONS
1. Shut off electrical power at fuse box before making any connections. All wiring
must comply with local, state, and national electrical codes.
2. Connect power cord to line voltage specified on motor and nameplate. Power
cord must be connected to a constant source of power (not a fan or other device
than runs intermittently). If power cord does not have a plug, wiring is as follows:
green/yellow - ground, brown - line, blue - neutral.
TESTING
1. Turn on power.
2. Test the unit after it is installed by filling the tank with water until the pump
comes on. Check the lines for leaks and kinks that will prevent full water
disposal. If water is not available, test the pump by removing the switch screen
and inserting differentiator top into switch housing bottom.
CAUTION: Do not run pump dry for more than a couple of seconds. Do not test this
way if water is present.
SERVICE INSTRUCTIONS
1. MAKE CERTAIN THE UNIT IS DISCONNECTED FROM THE POWER SOURCE
BEFORE ATTEMPTING TO SERVICE OR REMOVE ANY COMPONENT!
2. Be sure the floats move freely. Clean as necessary.
3. Pump screen is snapped on; remove it by pulling, then remove the three screws
that attach the volute. DO NOT remove any other screws.
4. Lightly clean any corrosion or debris that may clog the impeller. Use brush and
penetrating oil and lightly scrape to remove encrusted material.
5. Turn the impeller by hand to make sure it turns freely. Plug the unit in to see if
the impeller turns (see testing #2). Do not allow the pump to operate for more
than a couple of seconds. If the pump does operate, then replace the volute.
The unit should operate normally when connected to the correct voltage.
6. If for any reason these operations do not restore the unit to full service, call
your dealer or service. Do not in any case open the sealed portion of the unit or
remove screws other than those indicated above. Do not cut the electric cord
when removing the unit from the application. Disconnect the pump from its
regular connections. Failure to follow these guidelines may void the warranty.
7. If you remove the impeller and/or backplate, be certain to reassemble them
correctly. Impeller spacing is gauged from backplate to impeller edge. Use the
thickness of a dime to space the impeller away from backplate. Tighten set
screws on impeller to 3 - 5 inch pounds (hand tighten).
INTRODUCTION
FR
L’évacuateur de condensat à bac peu profond est spécialement conçu pour les
appareils de plafond ainsi que d’autres appareils de climatisation où une hauteur
minimale est importante. La pompe est conçue pour être placée directement dans
un bassin de rétention; il est aussi possible d’utiliser un réservoir fourni par le
fabricant. Ne pas utiliser la pompe où le niveau de l’eau peut dépasser la capacité
de la réservoir. Elle est commandée par un mécanisme à interrupteur flottant
l’active/l’éteint automatiquement.
Ce feuillet d’instructions couvre les modèles standard de cette série de pompes.
Il est aussi disponible pour d’autres modèles qui ne sont pas indiqués dans
ce document. Si votre pompe ne figure pas dans la liste, il faut faire preuve de
prudence pendant la commande de pièces de rechange. Toujours donner le
numéro de modèle et de catalogue de votre pompe au moment de commander
des pièces.
Bien lire les présentes instructions. Le non-respect de ces instructions annule
toutes les garanties et peut causer des dommages ou des blessures. Le câblage
et la plomberie doivent être permanents et conformes tout aux codes. Couper
l’alimentation électrique à la boîte de fusibles avant de faire l’entretien de la
pompe.
IN-PAN CONDENSATE REMOVAL
UNIT • ÉVACUATEUR INTERNE
DU CONDENSAT • UNIDAD DE
ELIMINACION DEL CONDENSADO EN
LA CUBETA
MODEL 1-ABS
Franklin Electric Co., Inc.
P. O. Box 12010
Oklahoma City, OK 73157-2010
405.947.2511 • Fax: 405.947.8720
www.LittleGiantPump.com
[email protected]
PERFORMANCE TABLE
Discharge
Sortie
Descarga
Flow (U.S. gallons/hour at feet
of head) • Débit (U.S. gallons/
heure élévation pieds d’eau) •
Flujo (U.S. galones/horacabeza
pies de agua)
Max P.S.I. •
Livres Par
Pouce Carré
• Maximo
Por Pulgada
Duadrada
Shutoff •
Tête d’arrêt
• Cabeza de
Cierre
1/4”
1’ 5’ 9’
4.3 10’
205 145 25
1
Highest point
Drop to bottom of
pump or below if
possible
Slope down from
highest point
PREFERRED INSTALLATION
ALTERNATE INSTALLATION
Inverted U-trap
Horizontal line
Figure 1
Page is loading ...
3
REPLACEMENT PARTS • LISTE DES PIÉCES DE RECHANGE •
LISTA DE PARTES
ITEM
NO.
PART
NO.
DESCRIPTION • NOMENCLATURE •
DESCRIPCIÓN OTY.
1 902429 Screw • Vis • Tornillo 4
2 150103 Mounting bracket • Attache de montage • Soporte
de montaje
1
3 950284 Screen, float switch • Grille, interrupteur à flotteur
• Malla, interruptor de flotador
1
4 101376 Screen, intake • Filtre d’admission • Rejilla, toma 1
5 902411 Screw • Vis • Tornillo 3
6 116375 Volute • Volute • Difusor 1
7 928007 Seal ring • Joint d’étanchéité • Anillo de sellado 1
8 116437 Impeller • Rotor • Impulsor 1
9 150108 Plate, air bleed • Plaque, orifice de prise d’air •
Plato, hueco del respiradero
1
1
9
8
7
6
5
4
3
2
Figure 2
4. Limpie suavemente cualquier corrosión o material ajeno que podría obstruir
el impulsor. Utilice un cepillo y aceite penetrante y raspe ligeramente para
sacar el material incrustado.
5. Conecte la unidad para ver si el interruptor gira (vea ensayo #2). No
permita que la bomba funcione durante más de 2 segundos. Si la bomba
no funciona, cambie el canal colector y el tamiz. La unidad debiera operar
como nueva cuando se conecta al voltaje correcto.
6. Si por cualquier razón estas operaciones no restauran la unidad a pleno
servicio, llame a su distribuidor o persona de servicio. No abra bajo ninguna
circunstancia la porción sellada de la unidad o quite otros tornillos que
los indicados a continuación. No corte el cable de suministro de energía
demasiado corto cuando desmonte la unidad de la aplicación. Desconecte
la bomba de sus conexiones regulares. El no seguir estas directrices puede
resultar en al anulación de la garantía.
7. Si por cualquier razón usted desmonta el propulsor o placa posterior,
asegúrese de que se vuelven a instalar correctamente. El espaciamiento
del impulsor se mide desde la placa posterior al borde del impulsor. Use
el espesor de una moneda de 10 centavos para separar el impulsor de
la placa posterior. Apriete los tornillos de presión en el impulsor a 4 - 5
pulgadas. Libra (apretado a mano).
LIMITED WARRANTY
Your product is guaranteed to be in perfect condition when it leaves our Factory.
It is warranted against defective materials and workmanship for a period of 12
months from date of purchase by the user.
Any product that should fail for either of the above two reasons and is still within
the warranty period will be repaired or replaced at the option of Little Giant
Pump Company, Inc. dba Franklin Electric Water Transfer Systems (hereafter
“the Manufacturer”) as the sole remedy of buyer. For our customers in the
CONTINENTAL UNITED STATES: Please return the defective unit, postage paid,
to the factory at 301 N. MacArthur, Oklahoma City, OK 73127-6616. All defective
product returned under warranty will be fully inspected to determine the cause
of failure before warranty is approved.
For our customers located elsewhere; it is not economical, due to duties
and freight, to return the product to the factory for inspection. Please return
the defective unit to any authorized distributor or dealer with a brief written
explanation of the problem. If there are no apparent signs of customer abuse,
unit will be repaired or replaced. If dispute arises over replacement of the
product, the distributor or dealer is to segregate such items and hold for
inspection by a representative of the Manufacturer or notify factory with details
of the problem for factory disposition and settlement of warranty claim.
DISCLAIMER:
THE FOREGOING WARRANTY IS AN EXCLUSIVE WARRANTY IN LIEU OF ANY
OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTIES (INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE) TO THE EXTENT EITHER APPLIES
TO A PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE
EXPRESS WARRANTIES GIVEN ABOVE.
Warranty will be VOID if any of the following conditions are found:
1. Sealed motor housing opened.
2. Product connected to voltage other than that indicated on nameplate.
3. Cord cut off to a length less than three feet.
4. Pump allowed to operate dry (fluid supply cut off).
5. Pump used to circulate anything other than fresh water at approximately
room temperature.
6. Product abuse by customer.
Any oral statements about the product made by the seller, the manufacturer,
the representatives or any other parties, do not constitute warranties, shall
not be relied upon by the user and are not part of the contract for sale.
Seller’s and manufacturer’s only obligation, and buyer’s only remedy, shall
be the replacement and/or repair by the manufacturer of the product as
described above. NEITHER SELLER NOR THE MANUFACTURER SHALL BE
LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR
CONSEQUENTIAL (INCLUDING, BUT NOT LIMITED TO INCIDENTAL OR
CONSEQUENTIAL DAMAGES FOR LOST PROFITS, LOST SALES, INJURY TO
PERSON OR PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL
LOSS), ARISING OUT OF THE USE OR THE INABILITY TO USE THE PRODUCT
AND THE USER AGREES THAT NO OTHER REMEDY SHALL BE AVAILABLE
TO IT. Before using, the user shall determine the suitability of the product for the
intended use, and user assumes all risk and liability whatsoever in connection
therewith.
Some states and countries do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights
which vary from state to state and country to country.
The National Electric Code (in the USA) and similar codes in other countries
require a Ground Fault Circuit Interrupter (GFCI) to be installed in the branch
circuit supplying fountain equipment rated above 15 volts. 115 volt GFCI’s (with
various cord lengths) are in stock, and we recommend each product be used
with a GFCI.
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Little GIANT 550521 Installation guide

Little GIANT
Brand
Little GIANT
Model
550521
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents