Whalen MLTOFBB User manual

Brand: Whalen

Model: MLTOFBB

Category: Baby furniture

Type: User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Bayside Furnishings

Page 1 Factory # 96-15197

Midland Twin over Full Bunk Bed

Model # MLTOFBB

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the

store where it was purchased. Please call our toll-free customer service number and have your

instructions and parts list ready to provide the model name, part name or factory number:

877-494-2536

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday

Or visit our website www.baysidefurnishings.com

Or e-mail your request to [email protected]

LOT NUMBER:

DATE OF PURCHASE: / /

Model # MLTOFBB

Bayside Furnishings

Page 2 Factory # 96-15197

QUALITY GUARANTEE

We are confident that you will be delighted with your Bayside Furnishings

purchase.

Should this product be defective in workmanship or materials or fail under normal use, we will repair

or replace it for up to one (1) year from date of purchase. Every Bayside Furnishings

product is

designed to meet your highest expectations. We guarantee that you will immediately see the value of

our fine furniture.

This warranty gives you specific legal rights and you may also have other rights which vary from State

to State.

Customer Service: 877-494-2536

8:30 a.m. - 4:30 p.m., PST, Monday to Friday

www.baysidefurnishings.com

ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF THE

BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL THAT RUNS

THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST THE WALL TO

PREVENT ENTRAPMENT BETWEEN THE BED AND WALL.

STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed that are

not designed for use with the bed; for example, but not limited to, hooks, belts, and jump ropes.

Prohibit more than one person on upper bunk.

Maximum mattress thickness must not exceed 23 cm (9 in.). Surface of mattress must be at least

13 cm (5 in.) below the upper edge of guardrails.

Use only mattress which is 1.8 m (74 in.) to 1.9 m (75 in.) long and 95 cm (37½ in.) to 98 cm (38 ½

in.) wide on the bunk bed.

Use only mattress that is 1.8 m (74 in.) to 1.9 m (75 in.) long and 1.3 m (52½ in.) to 1.4 m (53½ in.)

wide on bottom bunk.

Replacement parts, including additional guardrails, may be obtained from any of Bayside

Furnishings dealer.

Model # MLTOFBB

Bayside Furnishings

Page 3 Factory # 96-15197

TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT

OR FALLS

• Follow the information on the warnings appearing on the upper bunk end

structure and on the carton. Do not remove warning label from bed.

• Always use the recommended size mattress or mattress support, or both, to help

prevent the likelihood of entrapment or falls.

• Surface of mattress must be at least 12.7 cm (5 in.) below the upper edge of

guardrails.

• Do not allow children under 6 years of age to use the upper bunk.

• Periodically check and ensure that the guardrail, ladder and other components

are in their proper position, free from damage and that all connectors are tight.

• Do not allow horseplay on or under the bed and prohibit jumping on the bed.

• Always use the ladder for entering and leaving the upper bunk.

• Do not use substitute parts. Contact the manufacturer or dealer for replacement

parts.

• Use of a night light may provide added safety precaution for a child using the

upper bunk.

• Always use guardrails on both long sides of the upper bunk. If the bunk bed will

be placed next to the wall, the guardrail that runs the full length of the bed

should be placed against the wall to prevent entrapment between the bed and

wall.

• The use of water or sleep flotation mattress is prohibited.

• STRANGULATION HAZARD – Never attach or hang items to any part of the

bunk bed that are not designed for use with the bed; for example, but not limited

to, hooks, belts, and jump ropes.

• Prohibit more than one person on upper bunk.

• Keep these instructions for future reference.

This product was manufactured October 2012.

Model # MLTOFBB

Bayside Furnishings

Page 4 Factory # 96-15197

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present before

beginning assembly.

A- Lower Headboard (1) B- Lower Footboard (1) C- Upper Headboard (1) D- Upper Footboard (1)

E- Mattress Side Rail (3) F- Ladder Side Rail (1)

G- Long Guardrail (2) H- Short Guardrail (2) I- Front Guardrail Post (1)

J- Lower Mattress Support Slats (1) K- Upper Mattress Support Slats (1) L- Ladder (1)

Model # MLTOFBB

Bayside Furnishings

Page 5 Factory # 96-15197

Parts and Hardware List

Please read completely through the instructions and verify that all parts listed are present before

beginning assembly.

① Ø5/16” x 110 mm Bolt (32+1 extra) ② Ø1/4” x 35 mm Bolt (2+1 extra)

③ Barrel Nut ④ 1” Screw ⑤ 3/4” Screw

(32+1 extra) (80+2 extra) (2+1 extra)

⑥ Bed Connector Pin Floor Protector ⑦ M4 Allen Wrench

(4) (4+1 extra) (2)

Tools required

: Allen wrench (provided) and Phillips screwdriver (not provided).

Model # MLTOFBB

Bayside Furnishings

Page 6 Factory # 96-15197

ASSEMBLING LOWER BUNK

NOTE: Please follow the instructions carefully to insure a safe and sturdy bed. Do not

fully tighten the bolts until all rails and guardrails are attached.

1. Unpack the unit and confirm that you have all hardware and parts required.

2. Insert two Barrel Nuts ③ into each end of the Mattress Side Rails (E). Be sure that the cross slot on the

Barrel Nut faces out and that the threaded hole points towards the entry of the bolt along the Side Rail.

3. Bolt the Mattress Side Rail (E) to the Lower Headboard (A) by inserting two Ø5/16” x 110 mm Bolts

① through the holes in the post of the Headboard and into the Barrel Nuts ③ in the Mattress Side Rail.

Make sure the wood stoppers attached to the side rail for slats are up and face inward.

Screw in only part way using the Allen Wrench provided.

4. Repeat this procedure until all 4 corners are attached to the Lower Headboard (A) and Lower Footboard

(B). Once all 4 corners are attached, fully tighten all the bolts.

Barrel Nut

(8 used in this step)

③

Ø5/16” x 110 mm Bolt

(8 used in this step)

①

Model # MLTOFBB

Bayside Furnishings

Page 7 Factory # 96-15197

ASSEMBLING LOWER BUNK

5. Now, lay out the Lower Mattress Support Slats (J) in place between the wood stoppers on both

Mattress Side Rails (E). Make sure that every slot has a slat. Insert and screw the 1” Wood Screws

④

into the pre-drilled counter sunk holes in each end of the slats, as shown.

1” Screw

(40 used in this step)

④

Model # MLTOFBB

Bayside Furnishings

Page 8 Factory # 96-15197

ASSEMBLING UPPER BUNK

WARNING LABEL ON HEADBOARD MUST ALWAYS FACE INWARD.

6. Attach the remaining Mattress Side Rail (E) to the bottom two holes of the Upper

Headboard (C) using two Ø5/16” x 110 mm Bolts

① and Barrel Nuts ③. Make sure the

wood stoppers for slats attached on side rail are up and face inward.

7. Attach 2 Long Guardrails (G) to the Upper Headboard (C) as shown in the illustration.

8. Repeat the last two steps to attach the Mattress Side Rail (E) and Long Guardrails (G) to the

Upper Footboard (D).

9. Attach the Ladder Side Rail (F) to the Upper Headboard (C) and Footboard (D) using

the Ø5/16” x 110 mm Bolts

① and Barrel Nuts ③. Once all rails are attached, fully

tighten all the bolts.

NOTE: The Ladder Side Rail has two holes for the Front Guardrail Post (part I).

Barrel Nut

(16 used in this step)

③

Ø5/16” x 110 mm Bolt

(16 used in this step)

①

Model # MLTOFBB

Bayside Furnishings

Page 9 Factory # 96-15197

ASSEMBLING UPPER BUNK

10. Lay out the Upper Mattress Support Slats (K) between the wood stoppers on the Mattress Side Rail (E)

and Ladder Side Rail (F), ensuring that every slot has a slat. Insert and screw the 1” Wood Screws

④

into the pre-drilled counter sunk holes in each end of the slats, as shown.

1” Screw

(40 used in this step)

④

Model # MLTOFBB

Bayside Furnishings

Page 10 Factory # 96-15197

ASSEMBLING UPPER BUNK

11.Now, attach the Front Guardrail Post (I) to the front side of the Ladder Side Rail (F)

using two Ø1/4” x 35 mm Bolts

② through the pre-drilled holes on the Post into the

inserted nuts on the Side Rail.

Ø1/4” x 35 mm Bolt

(2 used in this step)

②

Model # MLTOFBB

Bayside Furnishings

Page 11 Factory # 96-15197

ASSEMBLING UPPER BUNK

12.Attach two Short Guardrails (H) between the Front Guardrail Post (I) and the Upper

Headboard (C) using the Barrel Nuts

③ and Ø5/16” x 110 mm Bolts ①, as shown.

Tighten all the bolts with the Allen Wrench provided.

Barrel Nut

(8 used in this step)

③

Ø5/16” x 110 mm Bolt

(8 used in this step)

①

Model # MLTOFBB

Bayside Furnishings

Page 12 Factory # 96-15197

ASSEMBLY OF THE BUNK BED

13.Now, place the Lower Bunk in the desired location in the room where the bunk bed

will sit.

14.Insert four Bed Connector Pins

⑥ into the top holes of the Lower Bunk as shown.

15.Ask for assistance to place the Upper Bunk on the top of the Lower Bunk using the

pins as a guide.

NOTE: Make sure that the Upper Bunk sits completely on the top of the Lower Bunk

and the pins go all the way in, not leaving any gaps.

Bed Connector Pin

(4 used in this step)

⑥

Model # MLTOFBB

Bayside Furnishings

Page 13 Factory # 96-15197

ASSEMBLY OF THE LADDER

16.Hook the Ladder (L) securely over the top of the Ladder Side Rail (F), between the

Front Guardrail Post (I) and the Upper Footboard (D) in the opening provided. Screw

the two hooks, pre-attached on the top of Ladder, to the Ladder Side Rail (F) using

two 3/4” Screws

⑤ through the hole in the Ladder Hook.

ONLY USE THE LADDER IN THIS LOCATION. IT MUST BE SECURED WITH 2 SCREWS

TO HELP PREVENT ACCIDENTS OR INJURY FROM THE LADDER DISLODGING. MAKE

SURE YOU INSTALL THE LADDER AGAINST THE FRONT GUARDRAIL POST.

3/4” Screw

(2 used in this step)

⑤

Back Side

Model # MLTOFBB

Bayside Furnishings

Page 14 Factory # 96-15197

DISASSEMBLING THE BUNK BED

NOTE: The Bunk Bed can be separated into a Twin Bed and a Full Size Bed. In this case,

attach four Floor Protectors

⑦ onto the bottom of the posts of the Upper Headboard (C)

and the Upper Footboard (D). Guardrails are not necessary.

17. To convert the bunk bed back into a Twin bed and a Full size bed, first unscrew the bolts to remove the

Ladder and all Guardrails.

18. Have an assistant help to remove the Upper Bunk from the Lower Bunk.

19. Attach four Floor Protectors ⑦ onto the bottom of the Upper Bunk posts, as shown in the illustration.

The beds can now be placed in the desired locations.

Floor Protector

(4 used in this step)

⑦

Model # MLTOFBB

Bayside Furnishings

Page 15 Factory # 96-15197

Care and Maintenance

z Use a soft, clean cloth that will not scratch the surface when dusting.

z Use of furniture polish is not necessary. Should you choose to use polish, test first in an

inconspicuous area.

z Using solvents of any kind on your furniture may damage your furniture’s finish.

z Never use water to clean your furniture as it may cause damage to the finish.

z Always use coasters under beverage glasses and flowerpots.

z Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid

rubbing.

z Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may

create spotting within the furniture finish.

z Stains or marks from crayons or ink markers will be difficult to remove.

z In the event that your furniture is stained or otherwise damaged during use, we recommend that

you call a professional to repair your furniture.

z Check bolts/screws periodically and tighten them if necessary.

Further advice about wood furniture care

It is best to keep your furniture in a climate-controlled environment. Extreme temperature and

humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep

furniture away from direct sunlight as sun may damage the finish.

Proper care and cleaning at home will extend the life of your purchase. Following these important and

helpful tips will enhance your furniture as it ages.

We hope you enjoy your purchase for many years.

Thank you for choosing Bayside Furnishings

IF YOU NEED TO ORDER REPLACEMENT PARTS, PLEASE USE THE LIST BELOW

Midland Twin over Full Bunk Bed (MLTOFBB)

*MLTOFBB-1-UHB Upper Headboard *MLTOFBB-12-L Ladder

*MLTOFBB-2-UFB Upper Footboard *MLTOFBB-13-LH Ladder Hook

*MLTOFBB-3-LHB Lower Headboard *MLTOFBB-14-110B Ø5/16" x 110 mm Bolt

*MLTOFBB-4-LFB Lower Footboard *MLTOFBB-15-35B Ø1/4" x 35 mm Bolt

*MLTOFBB-5-FGP Front Guardrail Post *MLTOFBB-16-BN Barrel Nut

*MLTOFBB-6-SG Short Guardrail *MLTOFBB-17-1S 1" Screw

*MLTOFBB-7-LG Long Guardrail *MLTOFBB-18-3/4S 3/4" Screw

*MLTOFBB-8-MSR Mattress Side Rail *MLTOFBB-19-BCP Bed Connector Pin

*MLTOFBB-9-LSR Ladder Side Rail *MLTOFBB-20-M4AW M4 Allen Wrench

MLTOFBB

UMSS

Upper Mattress Support Slats

MLTOFBB

Floor Protector

MLTOFBB-10-UMSS

Upper

Mattress

Support

Slats

MLTOFBB-21-FP

Floor

Protector

*MLTOFBB-11-LMSS Lower Mattress Support Slats *MLTOFBB-CH Complete Hardware

Whalen MLTOFBB User manual

Brand: Whalen

Model: MLTOFBB

Category: Baby furniture

Type: User manual

Download PDF

report

Whalen MLTOFBB User manual

Whalen MLTOFBB User manual

Related papers

Other documents