Wacker Neuson RT82-SC2 User manual

5200000973 05 0911

Operator’s Manual

Roller

RT 56SC-2

RT 82SC-2

Notice d’Emploi

Rouleau

5200000973

EN/FR

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000188911 08 0811

Foreword

wc_tx001529gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machines

covered in

this manual

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and main-

tain the above Wacker Neuson model(s). For your own safety and to reduce the

risk of injury, carefully read, understand, and observe all instructions described

in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Machine Item Number

RT 56 SC-2 0620294

0620844

RT 82 SC-2 0620293

0620367

0620368

0620525

0620528

0620529

0620530

0620845

5200003107

Foreword

4 wc_tx001529gb.fm

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-

charge of sparks or flames from the engine exhaust. Spark arresters are qualified

and rated by the United States Forest Service for this purpose. In order to comply

with local laws regarding spark arresters, consult the engine distributor or the local

Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and modifica-

tions. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker Neu-

son service center according to written instructions published by Wacker Neu-

son.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following conse-

quences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2011-CE-RT-en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

RT 56-SC2, RT 82-SC2

Trench Roller

To compact soil

0620844, 0620528, 0620529, 0620530, 0620845,

5200003107

15.5 kW

108 dB(A)

109 dB(A)

Conformity Assessment Procedure

According to ANNEX VIII

Notified Body

Lloyds Register Quality Assurance Limited (Notified Body No 0088)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Guidelines and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following guidelines and standards:

2006/42/EC, 2000/14/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 15.09.11

William Lahner

Vice President of Engineering

Paul Sina

Manager, Product Engineering

wc_bo5000188911_04TOC.fm 7

Table of ContentsRT SC-2

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 11

1.1 Signal Words Used in this Manual ..................................................... 11

1.2 Machine Description and Intended Use ............................................. 12

1.3 Operating Safety ................................................................................ 13

1.4 Operator Safety while Using Internal Combustion Engines ............... 15

1.5 Service Safety .................................................................................... 16

2 Labels 19

2.1 Label Locations .................................................................................. 19

2.2 Label Meanings .................................................................................. 20

3 Lifting and Transporting 27

3.1 Lifting the Machine ............................................................................. 27

3.2 Transporting the Machine ................................................................... 27

4 Operation 29

4.1 Preparing the Machine for First Use ................................................... 29

4.2 Control / Component Locations .......................................................... 30

4.3 Control / Component Descriptions ..................................................... 31

4.4 Features and Controls ........................................................................ 34

4.5 Accessing the Engine or Hydraulic Component Compartments ......... 35

4.6 Accessing the Control Compartment .................................................. 35

4.7 Control Panel ...................................................................................... 36

4.8 SmartControl™ SC-2 Transmitter ...................................................... 38

4.9 Infra-red System and Control Channels ............................................. 41

4.10 Before Starting ................................................................................... 43

4.11 Starting ............................................................................................... 44

4.12 Stopping ............................................................................................. 45

8 wc_bo5000188911_04TOC.fm

Table of Contents RT SC-2

4.13 Light Ring Color Codes .......................................................................46

4.14 Operation .............................................................................................47

4.15 Position of the Operator ......................................................................48

4.16 Range Limits .......................................................................................50

4.17 Operating Characteristics ....................................................................51

4.18 NiMH Battery .......................................................................................51

4.19 Replacing the Battery Pack .................................................................52

4.20 Charging the Transmitter Battery ........................................................52

4.21 Machine Stability .................................................................................54

4.22 Articulated Joint Locking Bar ...............................................................56

4.23 Tip-Overs .............................................................................................56

4.24 Emergency Shutdown Procedure ........................................................57

4.25 Overview of the ECM and the Diagnostic Tool ....................................57

4.26 ECM Stages of Engine Start Up ..........................................................58

4.27 ECM Monitoring of Solenoids ..............................................................59

4.28 Connecting the Diagnostic Tool ..........................................................60

4.29 Programming the ECM Tip-Over Mode ...............................................61

4.30 Entering the ECM Diagnostic Mode ....................................................62

4.31 ECM Fault and Error Codes ................................................................63

4.32 Resetting the ECM Diagnostic Data and the Tip-Over Light ...............66

4.33 Calibrating the Joysticks ......................................................................67

5 Maintenance 68

5.1 Break-in Period ....................................................................................68

5.2 Periodic Maintenance Schedule ..........................................................69

5.3 Hydraulic Oil Requirements .................................................................70

5.4 Hydraulic Oil Level ..............................................................................71

5.5 Changing Hydraulic Oil and Filter ........................................................72

5.6 Articulated Joint and Steering Cylinders .............................................74

5.7 Cleaning SmartControl™ Transmitter .................................................74

5.8 Scraper Bars .......................................................................................75

5.9 Shock Mounts ......................................................................................76

5.10 Changing Drums .................................................................................77

5.11 Battery .................................................................................................78

5.12 Engine Oil and Filter ............................................................................79

5.13 Servicing the Air Cleaner .....................................................................80

5.14 Engine Fuel Delivery System Maintenance .........................................81

5.15 Maintaining the Fuel Filter ...................................................................81

5.16 Draining the Fuel Filter Water Separator .............................................82

5.17 Priming the Fuel System .....................................................................82

wc_bo5000188911_04TOC.fm 9

Table of ContentsRT SC-2

5.18 Engine Coolant ................................................................................... 82

5.19 Adjusting Valve Clearance ................................................................. 83

5.20 Adjusting the Fan Belt ........................................................................ 84

5.21 Basic Troubleshooting ........................................................................ 85

5.22 Storage ............................................................................................... 87

5.23 Long-Term Storage ............................................................................ 87

6 Technical Data 88

6.1 Engine ................................................................................................ 88

6.2 Roller .................................................................................................. 89

6.3 Lubrication .......................................................................................... 89

6.4 Sound and Vibration Specifications .................................................... 90

6.5 Dimensions ......................................................................................... 90

6.6 Radiation Compliance ........................................................................ 90

7 AEM Safety Manual 91

8 Schematics 118

8.1 Electrical Schematic - Sheet 1 ......................................................... 118

8.2 Electrical Schematic - Sheet 2 ......................................................... 119

8.3 Components ..................................................................................... 120

8.4 Hydraulic Schematic ......................................................................... 124

8.5 Hydraulic Schematic Components ................................................... 125

10 wc_bo5000188911_04TOC.fm

Table of Contents RT SC-2

RT SC-2

wc_si000472gb.fm 11

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and

NOTE signal words which must be followed to reduce the possibility

of personal injury, damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a

situation which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f

To avoid death or serious injury from this type of hazard, obey all safety messages that

follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f

To avoid possible death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

CAUTION!

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f

To avoid possible minor or moderate injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

RT SC-2

12 wc_si000472gb.fm

1.2 Machine Description and Intended Use

This machine is a remote-controlled trench roller. The Wacker Neuson

Trench Roller consists of two distinct machine halves (front and rear)

joined by an articulated joint. Each machine half includes an exciter

assembly and two drums. The front half also includes a diesel engine

and pumps for the hydraulic system. The rear half includes the

hydraulic oil reservoir and the fuel tank. The diesel engine powers the

hydraulic systems that provide machine movement and drum

vibration. The operator controls all machine functions (steering,

vibration, and engine start/stop) using an infra-red control system.

This machine is intended to be used for compacting sub-bases,

backfill, and cohesive type soils.

This machine has been designed and built strictly for the intended

use(s) described above. Using the machine for any other purpose

could permanently damage the machine or seriously injure the

operator or other persons in the area. Machine damage caused by

misuse is not covered under warranty.

The following are some examples of misuse:

• Using the machine as a ladder, support, or work surface

• Using the machine to carry or transport passengers or equipment

• Using the machine to tow other machines

• Operating the machine outside of factory specifications

• Operating the machine in a manner inconsistent with all warnings

found on the machine and in the Operator’s Manual

This machine has been designed and built in accordance with the

latest global safety standards. It has been carefully engineered to

eliminate hazards as far as practicable and to increase operator

safety through protective guards and labeling. However, some risks

may remain even after protective measures have been taken. They

are called residual risks. On this machine, they may include exposure

to:

• Heat, noise, exhaust, and carbon monoxide from the engine

• Burns from hot hydraulic fluid

• Fire hazards from improper refueling techniques

• Fuel and its fumes

• Personal injury from improper lifting techniques

• Crushing hazards from improper operation and for other persons

in the work zone

RT SC-2

wc_si000472gb.fm 13

To protect yourself and others, make sure you thoroughly read and

understand the safety information presented in this manual before

operating the machine.

1.3 Operating Safety

Familiarity and proper training are required for the safe operation of the

machine. Machines operated improperly or by untrained personnel

can be hazardous. Read the operating instructions contained in this

manual and the engine manual, and familiarize yourself with the

location and proper use of all controls. Inexperienced operators should

receive instruction from someone familiar with the machine before

being allowed to operate it.

Operator qualifications

Only trained personnel are permitted to start, operate, and shut down

the machine. They also must meet the following qualifications:

• have received instruction on how to properly use the machine

• are familiar with required safety devices

The machine must not be accessed or operated by:

•children

• people impaired by alcohol or drugs

Contact Wacker Neuson for additional training if necessary.

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

operating this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

Before starting the machine

• ALWAYS disengage and stow the locking bar for the articulated

steering joint before operating the machine. The machine cannot

be steered when the locking bar is engaged.

• NEVER start a defective unit in need of service or repair.

• Do not operate the machine with unapproved accessories or

attachments.

• Do not transport the machine while it is running.

Controls and features

• Always operate machine with all safety devices and guards in

place and in working order. Do not modify or defeat safety

WARNING

RT SC-2

14 wc_si000472gb.fm

devices. Do not operate machine if any safety devices or guards

are missing or inoperative.

• ALWAYS check that all controls are functioning properly

immediately after start-up! DO NOT operate machine unless all

controls operate correctly.

• ALWAYS use the SmartControl™ transmitter neck strap provided

by Wacker Neuson while operating with the control cable

connected. This neck strap is designed to break away so that the

operator will not be dragged by the machine should the machine

slide, tip, or fall.

• NEVER operate the machine with the fuel cap loose or missing.

Work area awareness

• ALWAYS remain aware of changing positions and the movement

of other equipment and personnel on the job site.

• ALWAYS remain in visual contact with machine at all times while

operating controls.

• ALWAYS remain aware of changing surface conditions and use

extra care when operating over uneven ground, on hills, or over

soft or coarse material. The machine could shift or slide

unexpectedly.

• ALWAYS use caution when operating near the edges of pits,

trenches or platforms. Check to be sure that the ground surface is

stable enough to support the weight of the machine with the

operator and that there is no danger of the roller sliding, falling, or

tipping.

• ALWAYS position yourself safely when operating machine in

reverse or on hills. Leave enough space between yourself and

the machine so you will not be placed in a hazardous position

should the machine slide or tip.

• ALWAYS remain aware of moving parts and keep hands, feet,

and loose clothing away from the moving parts of the machine.

• Make sure that all other persons are at a safe distance from the

machine. Stop the machine if people step into the working area

of the machine.

• Do not use a cellphone or send text messages while operating

this machine.

• NEVER operate multiple rollers within 20 meters (65 feet) of one

another, unless you are certain that each roller and its

accompanying transmitter have been set to a different control

channel than the other rollers/transmitters being used within the

area. Refer to section Setting Control Channels for additional

information.

RT SC-2

wc_si000472gb.fm 15

• Stay clear of the articulated steering joint and the area between

the front and rear frames.

• NEVER leave the machine running unattended.

When work is complete

• Do not touch the engine or muffler while the engine is on or

immediately after it has been turned off. These areas get hot and

may cause burns.

• Store the machine properly when it is not being used. The

machine should be stored in a clean, dry location out of the reach

of children.

1.4 Operator Safety while Using Internal Combustion Engines

Operating safety

When running the engine:

• Keep the area around exhaust pipe free of flammable materials.

• Check the fuel lines and the fuel tank for leaks and cracks before

starting the engine. Do not run the machine if fuel leaks are present

or the fuel lines are loose.

When running the engine:

• Do not smoke while operating the machine.

• Do not run the engine near sparks or open flames.

• Do not touch the engine or muffler while the engine is running or

immediately after it has been turned off.

• Do not operate a machine when its fuel cap is loose or missing.

• Do not start the engine if fuel has spilled or a fuel odor is present.

Move the machine away from the spill and wipe the machine dry

before starting.

WARNING

Internal combustion engines present special hazards during operation and fueling. Failure to

follow the warnings and safety standards could result in severe injury or death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison. Expo-

sure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

RT SC-2

16 wc_si000472gb.fm

Refueling safety

When refueling the engine:

• Clean up any spilled fuel immediately.

• Refill the fuel tank in a well-ventilated area.

• Replace the fuel tank cap after refueling.

• Do not smoke.

• Do not refuel a hot or running engine.

• Do not refuel the engine near sparks or open flames.

1.5 Service Safety

Personal Protective Equipment (PPE)

Wear the following Personal Protective Equipment (PPE) while

servicing or maintaining this machine:

• Close-fitting work clothes that do not hinder movement

• Safety glasses with side shields

• Hearing protection

• Safety-toed footwear

In addition, before servicing or maintaining the machine:

• Tie back long hair.

• Remove all jewelry (including rings).

Before servicing the machine

• Always turn engine off before servicing machine. If the engine has

electric start, disconnect negative terminal on battery

• All adjustments and repairs MUST be completed before operation.

Do not operate the machine with a known problem or deficiency! All

repairs and adjustments should be completed by a qualified

technician.

• Do not modify the machine without the express written approval of

the manufacturer.

• Always secure the articulated steering joint using the locking bar

before lifting, jacking, and servicing the machine. The machine

WARNING

A poorly maintained machine may not function properly and may become a safety

hazard! Personal injury or equipment damage may occur.

f Maintain the machine according to the Periodic Maintenance schedules in this

manual. Make all necessary repairs before operating the machine.

RT SC-2

wc_si000472gb.fm 17

halves could swing together unexpectedly and cause a serious

injury.

• Always make sure slings, chains, hooks, ramps, jacks, and other

types of lifting devices are attached securely and have enough

weight-bearing capacity to lift or hold the machine safely. Always

remain aware of the location of other people in the area when lifting

the machine.

• Do not stand under the machine while it is being hoisted or moved.

While servicing the machine

• Do not attempt to clean or service the machine while it is running.

Rotating parts can cause severe injury.

• Do not use gasoline or other types of fuels or flammable solvents to

clean parts, especially in enclosed areas. Fumes from fuels and

solvents can become explosive.

• Do not remove the radiator cap when the engine is running or hot.

The radiator fluid is hot and under pressure and may cause severe

burns!

• Fluid leaks from small holes are often practically invisible. Do not use

your bare hands to check for leaks. Check for leaks using a piece of

cardboard or wood.

• Do not remove air cleaner cover, paper element, or precleaner while

engine is running.

• Do not open hydraulic lines or loosen hydraulic connections while the

engine is running! Hydraulic fluid under pressure can penetrate the

skin, cause burns, blind, or create other potentially dangerous

hazards. Set all controls in neutral and turn engine off before

loosening the hydraulic lines.

• Do not leave SmartControl™ transmitter unattended while servicing

machine.

After servicing the machine

• Always make sure hose connections have been reconnected back to

the correct fitting. Failure to do so may result in damage to the

machine and/or injury to person on or near the machine.

• Always replace the safety devices and guards after repairs and

maintenance.

• Before you start the machine, ensure that all tools have been

removed from the machine and that replacement parts and adjusters

are firmly tightened.

General service safety

• Always check all external fasteners at regular intervals.

RT SC-2

18 wc_si000472gb.fm

• Keep the machine clean and labels legible. Replace all missing and

hard-to-read labels. Labels provide important operating instructions and

warn of dangers and hazards.

• When replacement parts are required for this machine, use only

Wacker Neuson replacement parts or those parts equivalent to the

original in all types of specifications, such as physical dimensions,

type, strength, and material.

• Always do periodic maintenance as recommended in the Operator’s

Manual.

RT SC-2

wc_si000473gb.fm 19

2 Labels

2.1 Label Locations

Z

Y

X

Q

N

wc_gr007266

RT SC-2

20 wc_si000473gb.fm

2.2 Label Meanings

A

WARNING!

Pressurized contents. Do not open when hot!

B

WARNING!

Hot surface

C

WARNING!

Pinch point.

D

Hydraulic oil reservoir fill tube.

Page is loading ...

Wacker Neuson RT82-SC2 User manual

This manual is also suitable for

Wacker Neuson RT82-SC2 User manual

in other languages

Related papers

Other documents