Livex Lighting 2386-07 Installation guide

Brand: Livex Lighting

Model: 2386-07

Type: Installation guide

Livex Lighting 2386-07 is an outdoor wall mount light fixture, suitable for illuminating outdoor areas such as patios, balconies, and entryways. It is designed to be easy to install and maintain, with clear instructions provided in the manual. The fixture is made of durable materials and has a classic design that will complement any outdoor décor. It is also UL listed for safety and quality assurance.

ASSEMBLING

ASSEMBLING &

& INSTALLATION

INSTALLATION

INSTALLATION INSTRUCTIONS

INSTRUCTIONS

INSTRUCTIONS PRODUCT#

PRODUCT#

PRODUCT# 2181

2181

2181 2281

2281

2281 2381

2381

2381 2386

2386

2386 2162

2162

2162 2165

2165

2165 2168

2168

2172

2172 OUTDOOR

OUTDOOR

WALL

MOUNT

MOUNT LIGHT

LIGHT

LIGHT FIXTURE

FIXTURE

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

MOUNTING

MOUNTING THE

THE

THE FIXTURE

FIXTURE

Installation

Installation (see

(see

(see fig.1)

fig.1)

1. Shut off the power at the circuit breaker and remove old

fixture, including the cross bar.

2. Carefully unpack new fixture and lay all the parts on a clear

surface. Take care not to lose any small parts necessary for

installation.

3. Attach the mo unting screw part way into the side hole of the

crook cross bar , then lock it securely with hex nut until

becoming . Attach the cross bar to the junction box using two

box screws . The side of the cross bar marked “ GND ” must

face out.

4. Follow wiring instructions carefully (see

(see

(see fig.2)

fig.2)

5. Using the end of arm(A) hook the lamp body's loop,

aligning the end hole of the arm(A) with the top hole of back

plate , lock it securely with screw(E) and hex nut. Put the

candle sleeve(D) over the lamp holder.

6. Attach the back plate of the lamp body(B) onto the junction

box, aligning screws on cross bar with mounting holes and

lock it securely with the ball nuts(C).

7. Install the light bulb s in accordance with the fixture

’

specifications. DO

DO NOT

NOT

NOT EXCEED

EXCEED

EXCEED THE

THE

THE MAXIMUM

MAXIMUM

WATTAGE

RATING!

8. With

With

With silicone

silicone

silicone caulking

caulking

caulking compound,

compound,

compound, caulk

caulk

caulk completely

completely

around

around where

where

where back

back

back of

of cover

cover

cover meets

meets

meets with

with

with the

the

the wall

wall

wall surface

surface

to prevent

prevent

prevent water

water

water from

from

from seeping

seeping

seeping into

into

into outlet

outlet

outlet box.

box.

Wiring

Wiring (see

(see

(see fig.2)

fig.2)

1. Connect the electrical wires as follows. Connect the

black wire from the fixture to the black house (hot)

Wire. Connect the white wire from the fixture to the

white (neutral) house wire. Make sure all wire nuts are

secured.

You

may wrap the connections with electrical

tape. If your outlet box has a ground wire (green or bare

copper) connect fixture

’

s ground wire to it. Otherwise

attach the bare copper fixture wire to the green ground

screw on the cross bar.

2.Tuck the wire connections neatly into the wall junction

box.

F ig.1

Fig.2

White or

HOUSE

Black

WIRES

(Hot)

Smooth

FIXTURE

WIRES

Black or

Ribbed

WIRES

FIXTURE

Bare Copper(Ground)

FIXTURE

WIRES

Copper

(Ground)

HOUSE

(Neutral)

WIRES

White

Bare

Green or

WIRES

HOUSE

Listed

Livex Lighting 2386-07 Installation guide

Livex Lighting 2386-07 Installation guide

Livex Lighting 2386-07 Installation guide

Related papers

Other documents