Hunter Fan 50057 Owner's manual

Brand: Hunter Fan

Model: 50057

Type: Owner's manual

www.ventiladoreshunter.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

ENGLISH

Important Instructions: Keep Instructions for future use

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

PAG E

30 inches

7 feet

PAG E

What to Expect with

Your Installation

Ceiling Bracket

Ladder

PAG E

Tools Needed

Table of Contents

Mounting Options

PAG E

Wiring CanopyDownrodPreparation

PAG E

Maintenance &

Cleaning

Troubleshooting

PAG E

Warranty Statement

PAG E

Switch Housing

PAG E

No Light Kit Option

PAG E

Light Kit Option

Blades

PAG E

Congratulations on purchasing your new Hunter® ceiling

fan! It will provide comfort and performance in your home

or ofce for many years. This installation and operation

manual contains complete instructions for installing and

operating your fan.

We are proud of our work and appreciate the opportunity

to supply you with the best ceiling fan available anywhere

in the world.

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

What to Expect with Your Installation

w.1 - To reduce the risk of re, electrical shock, or personal injury,

mount fan directly from building structure and/or an outlet

box marked acceptable for fan support of 31.8 kg and use the

mounting screws provided with the outlet box.

w.2 - To avoid possible electrical shock, before installing or

servicing your fan, disconnect the power by turning off the circuit

breakers to the outlet box and associated wall switch location. If

you cannot lock the circuit breakers in the off position, securely

fasten a prominent warning device, such as a tag, to the service

panel.

w.3 - To reduce the risk of re, electrical shock, or motor damage,

use only Hunter Solid State Speed Controls.

w.4 - To reduce the risk of personal injury, do not bend the blade

brackets when installing the blade brackets, balancing the blades, or

cleaning the fan. Do not insert foreign objects in between rotating fan

blades.

w.5 - This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities, or

people with a lack of experience and knowledge, unless they have

received instructions regarding the use of the device or under the

supervision of a person responsible for their safety.

w.6 - It is recommended that children be supervised to ensure that

they are not using the appliance improperly

c.1 - All wiring must be in accordance with national and local

electrical codes. If you are unfamiliar with wiring, use a qualied

electrician.

c.2 - Use only Hunter replacement parts.

You may need a

friend to help you.

Check box to see

fan weight

Assess location

0,50 meters

from blade tip to

nearest wall or

obstruction

2,3 meters

from bottom

edge of blade to

the oor

Know your wiring

If you are unfamiliar

with wiring, use a

qualied electrician.

WARNINGS

CAUTIONS

Must be able to

secure the fan to

building structure or

fan-rated outlet box.

Do not use a plastic

outlet box.

Select a downrod length

Standard Downrod

for ceilings 2,4 -3 meters high

Shorter Downrod

for fans installed close to ceiling

Longer Downrod

for ceilings 3 meters or higher

Use ONLY Hunter

Ceiling Fan branded

accessory light kits.

www.hunterfan.com.br

Tools Needed

Ladder

Pliers Wire Strippers

Screwdrivers

Power Drill

(optional)

3.5 mm Drill

Bit (optional)

8 mm Drill Bit

(optional)

If mounting to a support structure, you

will also need these tools.

Hammer

(optional)

MD500-01 • 09/19/14 • © Hunter Fan Company

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

Hang your fan by a standard downrod

(included) or use a shorter downrod (sold

separately) for Low-Prole Mounting.

Mounting Options

Note: Do not hang the fan from a

ceiling that is angled greater than 34°

Support

Structure

Ceiling

Outlet Box

(required)

Angled

Mounting

Style

Standard

Mounting

Style

Support

Structure

Ceiling

Outlet Box

(required)

Carefully choose the installation location

that allows for optimal air ow.

The support structure must be able to support 5

times the weight of the fan. The weight of the fan is

located on the product packaging.

You will need a longer downrod (sold

separately) to hang the fan from a

vaulted or angled ceiling.

If you have a at ceiling: If you have an angled ceiling:

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

Ceiling Bracket

Refer to warning w.1 on pg. 2

To avoid possible electrical shock, before

installing your fan, disconnect the power by

turning off the circuit breakers to the outlet

box associated with the wall switch location.

Make sure all four (4) bumpers

are still attached.

For angled ceilings, point

opening toward peak.

Use wood screws

(included) when securing

to support structure with

approved electrical outlet

box. Drill 3.5 mm pilot

holes in support structure

to aid in securing ceiling

bracket with hardware

found in the hardware

bag.

Use machine screws

(provided with outlet

box) when securing to

existing ceiling fan-rated

outlet box. Make sure

it is securely installed

and is acceptable for fan

support of 31.8 kg or less.

OFF

Turn Power

Note: Do not mount ceiling fan

to a plastic outlet box.

Use concrete anchors (included)

when securing to support structure

with approved outlet box in a concrete

ceiling. Drill 8 mm pilot holes in

support structure. Hammer the M6

expansion anchors into the holes until

the ends are ush with the ceiling.

Install the washer, isolator, and nut

found in the hardware bag to

the expansion anchors.

www.hunterfan.com.br

Ceiling Bracket (continued)

Preparation

Remove the shipping blocks from the

motor. Save the screws. They will be

needed for blade iron installation.

Note: Some fans will have a shipping

ring instead of shipping blocks. Please

remove the ring and save the screws.

MD500-01 • 09/19/14 • © Hunter Fan Company

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

Downrod

S lide

1 2 3 4 5

678910

Sold Separately

Longer

Downrod

for angled

ceilings or

ceilings 3 m or

higher

Shorter

Downrod

for fans installed

close to ceiling

Standard

Downrod

for ceilings 2,4-3 m

high

Option 1Option 2

Option 3

skip to next page

If you need a different downrod length follow these steps:

Steps 1-5 to remove standard downrod pipe

Steps 6-10 to reassemble with new pipe

Included

(pre-assembled)

Sold Separately

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

20 cm

1 cm

(not to scale)

Remove the pre-installed

setscrew so that the downrod

can be inserted.

Hand tighten the downrod (at

least 4-5 full turns) until it stops.

The wires can be cut,

but leave at least 20 cm

extending from the top of

the downrod.

Downrod (continued)

Tighten the setscrew

with pliers. DO NOT

HAND TIGHTEN.

If the setscrew is not tightened

securely, the fan may fall.

20 cm 1 cm

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

Downrod (continued)

DO NOT PICK THE FAN UP BY THE CANOPY

OR WIRES. Place the downrod ball into the slot

in the ceiling bracket.

Put the wires and downrod through the canopy.

Let the canopy sit loosely on top of the fan.

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

Wiring

Using an orange wire

connector from

the hardware bag,

connect the 3 grounding

wires (green, green/

yellow stripe, or bare

copper) coming from the

ceiling, downrod, and

hanging bracket.

(Grounding)

Green/Yellow

Stripe

Green/Yellow

Stripe

Blue

Brown

(Grounded)

Note: To connect the wires,

hold the bare metal leads

together and place a wire

connector over them, then twist

clockwise until tight.

Using the orange wire

connectors from

the hardware bag, connect

the brown wire (ungrounded)

from the ceiling to the

brown and the black with

white stripe wires from the

fan. Connect the blue wire

(grounded) from the ceiling to

the blue wire from the fan.

Using the orange wire

connectors from

the hardware bag,

connect the blue wire

(grounded) from the

ceiling to the blue wire

from the fan.

Connect the brown wire

(ungrounded) from the

ceiling to the brown wire

from the fan. Connect the

second (ungrounded)

wire from the ceiling to

the black with white stripe

wire from the fan.

Blue

(Ungrounded)

Brown

Black with white stripe

(Grounded)

(Ungrounded)

For Dual Switches

For a Single Switch

Turn the splices upward and push them carefully back through the hanger bracket

into the outlet box. Spread the wires apart, with the grounded wires on one side of

the outlet box and the ungrounded wires on the other side of the outlet box.

Refer to CAUTION c.1 on pg. 2

White Stripe

(Ungrounded)

www.hunterfan.com.br

MD500-01 • 09/19/14 • © Hunter Fan Company

Canopy

Lift the canopy into place so that

the screw holes are aligned.

Position the canopy so that, when

lifted into place, the canopy ts into

the hanging bracket as shown.

Screw

Holes

Insert the two canopy screws

found in the hardware bag.

Note: Fan style may vary.

www.hunterfan.com.br

Blades

Remember the screws that

you kept after removing the

shipping blocks (page 6)? You

need them for this step.

Lightly attach the blade irons to the

motor with the blade iron armature

screws, then securely tighten after both

screws are attached.

Note: You need ten screws to complete

this step. Additional screws might be

found in the hardware bag.

Secure each blade to a blade iron with

screws found in the hardware bag.

www.hunterfan.com.br

Feed the wire plug through the center

hole of the upper switch housing, then

wrap keyhole slots around the screws and

twist counterclockwise.

Screw two housing assembly screws

from the hardware bag halfway into

the motor housing. It does not matter

which two screw holes you choose.

Insert the third screw, found in

the hardware bag, into place and

then tighten all three screws.

Make sure the upper switch housing is securely

attached to the mounting plate. Failure to properly

secure all 3 assembly screws could result in the switch

housing xture falling.

Switch Housing

www.hunterfan.com.br

Make sure the lower switch housing is securely attached to

the upper switch housing. Failure to properly secure all three

assembly screws could result in the light xture falling.

Connect the plugs from the upper and

lower switch housings. Make sure to line up

the colored markings on the connectors.

Attach the pull chain pendant to the short chain

coming from the switch housing.

No Light Kit Option

Lift the lower switch housing until its

screw holes are aligned with the screw

holes in the upper switch housing. Install the

three switch housing screws, found in the

hardware bag. Tighten all three screws.

www.hunterfan.com.br

CONGRATUALTIONS!

YOU’RE DONE!

No Light Kit Option (continued) Light Kit Option

See page 19 for fan

operation instructions.

Hold the lower switch housing in both

hands and push the plug button out with

your thumb. Remove the cap. Remove the

metal plate by removing the plate screws.

SAVE THE SCREWS.

Plug

Button

Cap

Metal Plate

Plate Screws

Install the plate screws you saved into the

outer screw holes. in the lower switch housing.

www.hunterfan.com.br

Light Kit Option (continued)

Connect the end of the blue wire from the

lower switch housing to the blue wire from

the light kit. Connect the end of the black

with white stripe wire from the lower switch

housing to the black wire from the light kit.

Twist a wire connector onto the bare wires

clockwise until tight.

Lower

Switch

Housing

Remove the upper light kit housing

by removing the light kit attachment

screws from the upper light kit

housing. SAVE THE SCREWS.

Align the screw holes in the upper light

kit housing with the screws in the lower

switch housing. Install the upper light kit

housing and rotate to engage. Securely

tighten the screws.

www.hunterfan.com.br

Using the previously saved light attachment

screws, install the lower switch housing to

the light kit housing.

Lift the lower switch housing until its screw

holes are aligned with the screw holes in the

upper switch housing. Install the three switch

housing screws, found in the hardware

bag. Tighten all three screws.

Connect the plugs from the upper and

lower switch housings. Make sure to line

up the colored markings on the connectors.

www.hunterfan.com.br

Press the globe ush against the

metal plate. Thread the light pull

chain through the hole in the

center of the nial cap and thread

the fan pull chain through the hole

in the side of the cap. Finally, thread

only the light pull chain through

the hole in the nial and screw the

nial onto the threaded rod.

Finial

Cap

Metal

Plate

Globe

Install a 14W CFL bulb (sold

separately) into each of the E27

sockets. When necessary, replace

with bulbs of same wattage.

CONGRATUALTIONS!

YOU’RE DONE!

Connect the appropriate pull

chain pendant to each of the short

chains coming from the nial

and nial cap. The fan pull chain

controls the speed: from high to

off. The light pull chain controls

the light xture: on and off.

Light

Pull

Chain

Fan

Pull

Chain

See next page for fan

operation instructions.

Light Kit Option (continued)

Page is loading ...

Hunter Fan 50057 Owner's manual

Brand: Hunter Fan

Model: 50057

Type: Owner's manual

Download PDF

report

Hunter Fan 50057 Owner's manual

Hunter Fan 50057 Owner's manual

Related papers

Other documents