Marantec Control x.301: Take control of your garage door and gate automation with cutting-edge technology, offering reliable operation, advanced security features, and smart home integration capabilities.
Marantec Control x.301: Take control of your garage door and gate automation with cutting-edge technology, offering reliable operation, advanced security features, and smart home integration capabilities.
Expansion module
Manual for installation and operation
GB
2 Manual for installation and operation, Expansion module GB (#81444)
1. Meaning of symbols 2. Table of contents
Caution!
Danger of personal injury!
The following safety advice must be
observed at all times so as to avoid
personal injury!
Attention!
Danger of material damage!
The following safety advice must be
observed at all times so as to avoid
material damage!
Advice / Tip
Check
Reference
i
Advice
1. Meaning of symbols . . . . . . . . . .2
2. Table of contents . . . . . . . . . . . .2
3. General safety advice . . . . . . . . .3
4. Product overview . . . . . . . . . . . .5
4.1 Supply package . . . . . . . . . . . .5
4.2 Performance Features . . . . . . .5
5. Installation . . . . . . . . . . . . . . . . .6
5.1 Mount the expansion module .6
5.2 Connection . . . . . . . . . . . . . . .6
6. Programming . . . . . . . . . . . . . . .9
6.1 Adjustment of traffic control . .9
6.2 Settings . . . . . . . . . . . . . . . . .12
7. Attachment . . . . . . . . . . . . . . . .13
EC Declaration of Conformity . . . . . . .13
Manual for installation and operation, Expansion module GB (#81444) 3
3. General safety advice
Target group
This operator system may only be installed, connected and put into operation by qualified and trained
professionals!
Qualified and trained specialist personnel are persons
- who have knowledge of the general and special safety regulations,
- who have knowledge of the relevant electro-technical regulations,
- with training in the use and maintenance of suitable safety equipment,
- who are sufficiently trained and supervised by qualified electricians,
- who are able to recognise the particular hazards involved when working with electricity,
- with knowledge regarding applications of the EN 12635 standard (installation and usage requirements).
Warranty
For an operations and safety warranty, the advice in this instruction manual has to be observed.
Disregarding these warnings may lead to personal injury or material damage. If this advice is disregarded,
the manufacturer will not be liable for damages that might occur.
To avoid installation errors and damage to the device, it is imperative that the installation instructions are
followed. The product may only be operated after reading these installation and operating instructions.
The installation and operating instructions are to be given to the door system user, who must keep them
safe. They contain important advice for operation, checks and maintenance.
This item is produced according to the directives and standards mentioned in the Manufacturer's
Declaration and in the Declaration of Conformity. The product has left the factory in perfect condition with
regard to safety.
Power-operated windows, doors and gates must be checked by an expert (and this must be documented)
before they are put into operation and thereafter as required, but at least once a year.
Correct use
The expansion module expands the x.21 control unit by the functions: radio control, traffic light function
and photocell drive-through barrier.
Beside the advice in these instructions, please observe the general safety and accident
prevention regulations! Our sales and supply terms and conditions are effective.
Please read carefully!
3. General safety advice
Installation tips
• Ensure that the devices to be connected (doors etc.) are in a mechanically faultless state.
• Before commencing cabling works it is very important to disconnect the system from the electricity
supply.
Ensure that the electricity supply remains disconnected throughout the cabling works.
• Adhere to the local protection regulations.
• Lay the electricity supply cables and control cables; these MUST be laid separately.
The operating voltage is 24 V.
Cleaning tips
Never use water jets, high pressure cleaners, acids or bases for cleaning.
Please read carefully!
4 Manual for installation and operation, Expansion module GB (#81444)
4.1 Supply package 4.2 Performance Features
1 Housing
2 Expansion module
3 Screw set
The expansion module expands the x.21 control
unit by the functions:
- traffic light functions (traffic control)
- photocell drive-through barrier
1
2
4. Product overview
Manual for installation and operation, Expansion module GB (#81444) 5
4.1 / 1
3
Advice:
In order to operate the expansion
module at the x.21 control unit,
a 2-wire photocell barrier has to be
connected and activated.
6 Manual for installation and operation, Expansion module GB (#81444)
Type / function
A DIP switch
XB99 Connection of control element
B Release slide
XB48 Connection of x.21 control unit
C
Display signal light
Drive-out red/green
D
Display signal light
Drive-in red/green
E Display photocell CLOSED
F Display OPEN/CLOSED end position
XH19A Connection signal lights ON
XH19B Connection of signal lights
XH14 Connection of wiping impulse
5.1 Mount the expansion module 5.2 Connection
5. Installation
• Open the housing.
• Remove the covers (A) from both housings.
• Screw the housing onto a firm surface.
• Fit the expansion module onto the rail in the
housing.
• Feed the connection cable from the x.21 control
unit into the expansion module housing.
5.2.1 Overview of control unit
5.1 / 1
Advice:
To ensure a proper connection to the
x.21 controls, the expansion module
housing must be mounted right next
to the x.21 control unit.
A
A
5.2.1 / 1
B
CDEF
XB99
XB48 XH19A
XH19BXH14
Manual for installation and operation, Expansion module GB (#81444) 7
5. Installation
5.2.2 Cabling
XB48
• Connect the x.21 control unit to the
XB48 terminal.
• Connect all expansions.
5.2.2 / 1
Type / function
SB31 Switching contact priority
SB33 Switching contact door OPEN
SB36 Impulse button, drive-in
SB37 Impulse button, drive-out
Terminal XB99
5.2.2 / 2
M07E026
8 Manual for installation and operation, Expansion module GB (#81444)
5. Installation
Type / function
HH92A Signal light drive-out green
HH92B Signal light drive-in green
HH94A Signal light drive-out red
HH94B Signal light drive-in red
L1 On-site supply voltage
N On-site supply voltage
Terminal XH19A / XH19BTerminal XH14
Type / function
KH42 Central relay, 3 minute light
L1 On-site supply voltage
N On-site supply voltage
-XH19A
L1
N
H1 94 H1 94A92A 94B92B
-XH19B
-HH92A
-HH92B
-HH94B
-HH94A
5.2.2 / 4
-XH14
L1
N
H1 42A 42B
-KH42
A2 A1
5.2.2 / 3
M07E026 M07E026
Manual for installation and operation, Expansion module GB (#81444) 9
Function Terminal SB36 Terminal SB37
no traffic control
(default)
OPEN button CLOSE button
Traffic control DRIVE-IN button DRIVE-OUT button
6. Programming
6.1 Adjustment of traffic control
If a timer is connected to terminal XB99, different settings for the traffic control system can be selected
with the DIP switches.
Button connections
Standard setting (no traffic control – DIP switches set to 000)
Terminals XH19A, XH19B and XH14 can be used for potential-free limit switch messages, OPEN and
CLOSE. Terminal XB99 can be used for an impulse button.
Traffic control
The different traffic control settings are listed in the table below.
6. Programming
10 Manual for installation and operation, Expansion module GB (#81444)
S1 S2 S3 Traffic control
1 0 0
Timer at SB33
Timer switches on:
- The door opens.
- The door remains open for the selected time.
- The traffic lights light up red.
- Pressing the button switches the green light on in the direction of travel.
0 1 0
Timer at SB33
Timer switches on:
- Door opens when a button is pushed.
- The door remains open for the selected time.
- The traffic lights light up red.
- Pressing the button switches the green light on in the direction of travel.
1 1 0
Timer at SB33
Timer switches on:
- The door opens.
- The door remains open for the selected time.
- The traffic lights light up red.
- Pressing the button switches the green light on in the direction of travel.
- When the photocell barrier has been driven past, the green phase ends.
0 0 1
Timer at SB33
Timer switches on:
- The door opens.
- The door remains open for the selected time.
- The traffic lights light up red.
- Pressing the button switches the green light on in the direction of travel.
- When the photocell barrier has been driven past, the green phase ends and the red phase is
shortened.
1 0 1
Timer at SB33
Timer switches on:
- The door opens.
- The door remains open for the selected time.
- The traffic lights alternate between red and green.
DIP switch setting
Manual for installation and operation, Expansion module GB (#81444) 11
6. Programming
S1 S2 S3 Traffic control
0 1 1
Timer at SB33
(Timed switching with two timers)
Time switch 1 switches on:
- The door opens.
- The door remains open for the selected time.
- Drive-in/drive out 1 lights continuously green.
- Drive-in/drive out 2 lights continuously red.
- Drive-in/drive out 2 gets green light when button is pressed.
Timer at SB33
(Timed switching with two timers)
Time switch 2 switches on:
- The door opens.
- The door remains open for the selected time.
- Drive-in/drive out 1 lights continuously red.
- Drive-in/drive out 2 lights continuously green.
- Drive-in/drive out 1 gets green light when button is pressed.
1 1 1 -
12 Manual for installation and operation, Expansion module GB (#81444)
6. Programming
6.2 Settings
Remote control
• Programme the remote control (if available).
Extended programme menu:
- Level 4 / Menu 1: Drive-in
- Level 4 / Menu 2: Drive-out
Green phase and red phase
• Program the time settings for the green phase
and the red phase.
Extended programme menu:
- Level 3 / Menu 3: door open time, green
- Level 3 / Menu 4: warning time, red
Photocell drive-through barrier
• Activate the photocell drive-through barrier.
Extended programme menu:
- Level 8 / Menu 1: Photocell
Reference:
The settings for the expansion
module functions are changed via
the x.21 control unit.
The settings are described under the
heading “Extended operator
functions” in the drive instructions.
i
Advice:
When the expansion module is
connected, the programming
configuration of the drive controls
changes to “Drive-in” and “Drive-
out”.
Manual for installation and operation, Expansion module GB (#81444) 13
7. Attachment
EC Declaration of Conformity
We hereby declare that the product sold by us
and mentioned below corresponds in its design,
construction and version to the relevant and basic
health and safety requirements of the following
EC regulations: EMC Directive, Machinery
Directive and Low Voltage Directive.
Product changes made without our consent will
render this Declaration void.
Product:
Relevant EC Regulations:
- EC EMC Directive
(89/336/EWG),
- Machinery Directive
(98/37/EWG) and
- Low Voltage Directive
(73/23/EWG und 93/68/EWG).
Applied harmonised standards, in particular:
EN 292-1 / EN 61000-6-2 / EN 61000-6-3 /
EN 55014 / EN 61000-3-2 / EN 61000-3-3 /
EN 60335-1 / EN 60335-2-95 / EN 12445 /
EN 12453 / EN 300220-1 / EN 301489-3 /
ETS 300683
Date / Signature
14 Manual for installation and operation, Expansion module GB (#81444)
Manual for installation and operation, Expansion module GB (#81444) 15
English Copyright.
No part of this manual may be reproduced without our prior consent.
Subject to changes which are in the interest of technical improvements.
Valid from: 08.2008
#81 444
1 - GB/KD 36-1-0163 - M - 0.5 - 0407
81444
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Marantec Control x.301: Take control of your garage door and gate automation with cutting-edge technology, offering reliable operation, advanced security features, and smart home integration capabilities.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Marantec Control x.301 Owner's manual
-
Marantec Comfort 390 plus Owner's manual
-
-
-
Marantec EM 131 Owner's manual
-
-
-
-
-