2. CyberData
  3. 011527 InformaCast Enabled WiFi Alert Button

CyberData 011527 InformaCast Enabled WiFi Alert Button, 011527 Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the CyberData 011527 InformaCast Enabled WiFi Alert Button Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is CyberData 011527?
    What does the InformaCast Enabled WiFi Alert Button do?
    What is included in the package?
    How do I enable the battery?
    What is the J1 Power Connection?
    What does the Reset Test Function Management (RTFM) button do?
    What are the dimensions of the InformaCast Enabled WiFi Alert Button?
    Can the device be mounted to a standard gang box?
Quick Reference 931786A © 2020, CyberData Corporation, ALL RIGHTS RESERVED© 2020, CyberData Corporation, ALL RIGHTS RESERVED 931786A Quick Reference
Mounting Options—Wall Mounting
Mounting Options—Optional Plastic Low Voltage Bracket (Not Included)
Contacting CyberData
4
2
1
6
3
5
To be installed and or used in accordance with the
appropriate electrical codes and regulations.
1. Prepare hole cutouts for both wires and the plastic-
ribbed anchors. Use the provided Mounting Template
or place the backplate directly onto the mounting
surface. Mark the surface, and then drill the holes. (Drill
Size: 3/16-inch / 4.8-mm) for the plastic-ribbed anchors.
2. Use a rubber mallet to hammer the plastic-ribbed
anchors into the prepared holes.
3. Line up the backplate's Elongated Hole to the plastic-
ribbed anchors.
4. Install the mounting screws through the backplate
and plastic-ribbed anchors.
5. Connect the wires to the terminals on the
InformaCast Enabled WiFi Alert Button. See the J1
Power Connection diagram on this Quick Reference
Placemat.
6. Put the InformaCast Enabled WiFi Alert Button and
the backplate together by installing the flat head
machine screw on the bottom.
3
2
1
2
4
5
1. Make a hole cutout for the Low Voltage Bracket*.
2. Fold down the flagnuts, and then insert the Low
Voltage Bracket into the hole cutout.
3. Install the mounting screws* through the backplate
and the Low Voltage Bracket.
4. Connect the wires to the terminals on the
InformaCast Enabled WiFi Alert Button. See the J1
Power Connection diagram on this Quick Reference
Placemat.
5. Put the InformaCast Enabled WiFi Alert Button and
the backplate together by Installing the flat head
machine screw on the bottom.
*The Low Voltage Bracket and mounting screws are
not provided.
To be installed and or used in accordance with the
appropriate electrical codes and regulations.
Sales: 831-373-2601 ext. 334
Support: 831-373-2601 ext. 333
Support Website: http://support.cyberdata.net/
RMA Department: 831-373-2601 ext. 136
RMA Email: [email protected]
RMA Status: http://support.cyberdata.net/
Warranty Information: http://support.cyberdata.net/
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
http://www.cyberdata.net/
Typical Installation
Getting Started
• Download the InformaCast Enabled WiFi Alert Button Operations Guide PDF file from the Downloads tab at:
http://www.cyberdata.net/products/011527/
• Create a plan for the locations of your speakers.
• WARNING: To prevent injury, this apparatus must be securely attached to the wall in accordance with the installation
instructions.
• WARNING: The USB or J3 connectors are intended for intra-building connections only and do not route to the outside plant.
• WARNING: The device enclosure is not rated for any AC voltages!
Parts
When the InformaCast Enabled WiFi Alert Button is
depressed, it sends a message to the InformaCast Server.
This will generate an event within the InformaCast software
which will then generate an appropriate mass notification
response.
InformaCast Server
PoE Switch
802.11 b.g.n
InformaCast Protocol
M2M interface/SNMP Trap
InformaCast Enabled WiFi Alert Button Connectivity
InformaCast Enabled WiFi Alert Button
+5V Power with built-in battery
011396 InformaCast Enabled Speaker
011377 InformaCast Enabled RGB (Multi-Color) Strobe
011472 InformaCast Enabled IP66 Outdoor Horn
WiFi Access Point
Accessory Kit
(1x) M3 Flat Head Machine Screw
(4x) Plastic Ribbed Anchor
(4x) Wall Mounting #6x1.25" Pan
Head Phillips Sheet Metal Screw
(1) USB to AC Adapter(1) InformaCast Enabled WiFi
Alert Button Assembly
(1) Accessory Kit
3 ft USB Cable for WiFi Button
The IP Endpoint Company
Installation Quick Reference
InformaCast Enabled WiFi Alert Button
011527
© 2020, CyberData Corporation, ALL RIGHTS RESERVED 931786A Quick Reference Quick Reference 931786A © 2020, CyberData Corporation, ALL RIGHTS RESERVED
Reset Test Function Management (RTFM) Button
Dimensions and Mounting Template
When the device is operational and linked to a network,
you can use the Reset Test Function Management (RTFM)
button (SW3 [see picture]) to restore the device to the
factory default settings.
To restore the device to factory default settings:
• Press and hold the RTFM button for three seconds.
1.012
4.528 [115.00]
2.953 [75.00]
[25.70]
Note: The alternate two holes of the back plate can be
Dimensions are in Inches [Millimeters]
used to mount to most standard gang boxes.
J1 Power Connection
Optional Auxiliary Power Supply (Part #561015 [Sold Separately])
5V Output
Red: +5VDC connects to J3 (+)
Black: Ground connects to J3 (-)
AC Power Input
Blue - Neutral
Brown - Line
0.4A @ 230VAC
0.8A @ 115VAC
J3 = Auxiliary Power Input
J3 Power Connection
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
WiFi Alert Button
Enable the Battery
Before Installation
/