Lenovo ThinkPad Series User manual

ThinkPad CD-RW/DVD-ROM Ultrabay

Serial ATA Drive User Guide

ThinkPad CD-RW/DVD-ROM Ultrabay

Serial ATA Drive User Guide

ATTENTION

Before installing this product, read the ThinkPad System Safety Booklet.

Note

Be sure to retain your proof of purchase. It might be required to receive warranty service. See Appendix B, “Lenovo Limited

Warranty,” on page 15.

First Edition (June 2008)

Portions © Copyright International Business Machines Corporation 2005.

LENOVO products, data, computer software, and services have been developed exclusively at private expense and

are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted

rights to use, reproduction and disclosure.

LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered

pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions

set forth in Contract No. GS-35F-05925.

Contents

Safety information . . . . . . . . . .v

General safety guidelines . . . . . . . vii

Service . . . . . . . . . . . . . . . . vii

Power cords and power adapters . . . . . . . vii

Extension cords and related devices . . . . . . vii

Plugs and outlets . . . . . . . . . . . . viii

Batteries . . . . . . . . . . . . . . . viii

Heat and product ventilation . . . . . . . . viii

Chapter 1. About the ThinkPad

CD-RW/DVD-ROM Ultrabay Serial ATA

Drive . . . . . . . . . . . . . . . .1

Product description . . . . . . . . . . . .1

Software description . . . . . . . . . . . .1

Installation requirements . . . . . . . . . .2

Installing the drive . . . . . . . . . . . .2

Locating the drive controls . . . . . . . . .2

Chapter 2. Using the ThinkPad

CD-RW/DVD-ROM Ultrabay Serial ATA

Drive . . . . . . . . . . . . . . . .3

Before you begin . . . . . . . . . . . . .3

Handling and caring for a disc . . . . . . . .3

Caring for the CD-RW/DVD-ROM Ultrabay Serial

ATA Drive . . . . . . . . . . . . . . .4

Loading a disc . . . . . . . . . . . . . .4

Manually ejecting a disc . . . . . . . . . .4

Using CD-R and CD-RW discs . . . . . . . .5

Installing software . . . . . . . . . . . .5

Using Intervideo WinDVD . . . . . . . . . .6

Installing WinDVD and viewing a DVD movie . .6

Starting WinDVD . . . . . . . . . . . .7

Using Drag-to-Disc (DLA) . . . . . . . . . .7

Using Creator Business Edition . . . . . . . .8

Backing up a CD . . . . . . . . . . . .8

Copying and imaging discs . . . . . . . .8

Problem solving . . . . . . . . . . . . .9

Appendix A. Service and Support . . .13

Registering your option . . . . . . . . . .13

Online technical support . . . . . . . . . .13

Telephone technical support . . . . . . . . .13

Appendix B. Lenovo Limited Warranty 15

Warranty information . . . . . . . . . . .18

Suplemento de Garantía para México . . . . . .19

Appendix C. Notices . . . . . . . . .21

Recycling information . . . . . . . . . . .22

Trademarks . . . . . . . . . . . . . .22

Appendix D. Electronic emission

notices . . . . . . . . . . . . . . .23

Federal Communications Commission (FCC)

Declaration of Conformity . . . . . . . . .23

Appendix E. China RoHS . . . . . . .27

iv ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

Safety information

Before installing this product, read the Safety Information.

Antes de instalar este produto, leia as Informações de Segurança.

Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.

Læs sikkerhedsforskrifterne, før du installerer dette produkt.

Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.

Avant d’installer ce produit, lisez les consignes de sécurité.

Vor der Installation dieses Produkts die Sicherheitshinweise lesen.

Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.

Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.

Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.

Antes de instalar este produto, leia as Informações sobre Segurança.

Antes de instalar este producto lea la información de seguridad.

Läs säkerhetsinformationen innan du installerar den här produkten.

vi ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

General safety guidelines

Always observe the following precautions to reduce the risk of injury and property damage.

Service

Do not attempt to service a product yourself unless instructed to do so by the Customer Support Center.

Use only a service provider who is approved to repair your particular product.

Note: Some parts can be upgraded or replaced by the customer. These parts are referred to as Customer

Replaceable Units, or CRUs. Lenovo expressly identifies CRUs as such, and provides

documentation with instructions when it is appropriate for customers to replace those parts. You

must closely follow all instructions when performing such replacements. The Off state of a power

indicator does not necessarily mean that voltage levels inside a product are zero. Always make

sure that the power is turned off and that the product is unplugged from any power source before

you attempt the replacement. If you have any questions or concerns, contact the Customer Support

Center.

Power cords and power adapters

Use only the power cords and power adapters supplied by the product manufacturer.

Never wrap a power cord around the power adapter or other object. Doing so can stress the cord in ways

that can cause the cord to fray, crack or crimp. This can present a safety hazard.

Always route power cords so that they will not be walked on, tripped over, or pinched by objects.

Protect the cord and power adapters from liquids. For instance, do not leave your cord or power adapter

near sinks, tubs, toilets, or on floors that are cleaned with liquid cleansers. Liquids can cause a short

circuit, particularly if the cord or power adapter has been stressed by misuse. Liquids can also cause

gradual corrosion of the power cord terminals and/or the connector terminals on the adapter which can

eventually result in overheating.

Always connect power cords and signal cables in the correct order and ensure that all power cord

connectors are securely and completely plugged into receptacles.

Do not use any power adapter that shows corrosion at the ac input pins and/or shows signs of

overheating (such as deformed plastic) at the ac input or anywhere on the power adapter.

Do not use any power cords where the electrical contacts on either end show signs of corrosion or

overheating or where the power cord appears to have been damaged in any way.

Extension cords and related devices

Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you

use are rated to handle the electrical requirements of the product. Never overload these devices. If power

strips are used, the load should not exceed the power strip input rating. Consult an electrician for more

information if you have questions about power loads, power requirements, and input ratings.

Plugs and outlets

If a receptacle (power outlet) that you intend to use with your computer equipment appears to be

damaged or corroded, do not use the outlet until it is replaced by a qualified electrician.

Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a

replacement.

Some products are equipped with a three-pronged plug. This plug fits only into a grounded electrical

outlet. This is a safety feature. Do not defeat this safety feature by trying to insert it into a non-grounded

outlet. If you cannot insert the plug into the outlet, contact an electrician for an approved outlet adapter

or to replace the outlet with one that enables this safety feature. Never overload an electrical outlet. The

overall system load should not exceed 80 percent of the branch circuit rating. Consult an electrician for

more information if you have questions about power loads and branch circuit ratings.

Be sure that the power outlet you are using is properly wired, easily accessible, and located close to the

equipment. Do not fully extend power cords in a way that will stress the cords.

Connect and disconnect the equipment from the electrical outlet carefully.

Batteries

All personal computers manufactured by Lenovo contain a non-rechargeable coin cell battery to provide

power to the system clock. In addition many mobile products such as notebook PCs utilize a rechargeable

battery pack to provide system power when in portable mode. Batteries supplied by Lenovo for use with

your product have been tested for compatibility and should only be replaced with Lenovo approved

parts.

Never attempt to open or service any battery. Do not crush, puncture, or incinerate batteries or short

circuit the metal contacts. Do not expose the battery to water or other liquids. Only recharge the battery

pack strictly according to instructions included in the product documentation.

Battery abuse or mishandling can cause the battery to overheat, which can cause gasses or flame to

“vent” from the battery pack or coin cell. If your battery is damaged, or if you notice any discharge from

your battery or the buildup of foreign materials on the battery leads, stop using the battery and obtain a

replacement from the battery manufacturer.

Batteries can degrade when they are left unused for long periods of time. For some rechargeable batteries

(particularly Lithium Ion batteries), leaving a battery unused in a discharged state could increase the risk

of a battery short circuit, which could shorten the life of the battery and can also pose a safety hazard. Do

not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged

state.

Heat and product ventilation

Computers, AC power adapters, and many accessories can generate heat when turned on and when

batteries are charging. Always follow these basic precautions:

v Do not leave your computer, AC power adapter, or accessories in contact with your lap or any part of

your body for an extended period when the products are functioning or when the battery is charging.

Your computer, AC power adapter, and many accessories produce some heat during normal operation.

Extended contact with the body could cause discomfort or, potentially, a skin burn.

v Do not charge the battery or operate your computer, AC power adapter, or accessories near flammable

materials or in explosive environments.

viii ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

v Ventilation slots, fans, and heat sinks are provided with the product for safety, comfort, and reliable

operation. These features might inadvertently become blocked by placing the product on a bed, sofa,

carpet, or other flexible surface. Never block, cover, or disable these features.

General safety guidelines ix

x ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

Chapter 1. About the ThinkPad CD-RW/DVD-ROM Ultrabay

Serial ATA Drive

This manual provides information on registering, installing, and using the ThinkPad

®

CD-RW/DVD-ROM Ultrabay

™

Serial ATA Drive, and is available on the Software and User Guide CD in

multiple languages.

The appendixes of this guide contain warranty information and legal notices.

Product description

The ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive can write to and read from CD-RW and

CD-R discs, and can read mass-produced, stamped CDs and DVDs. This drive can also read DVD-RAM,

DVD-R, DVD-RW, DVD+R, and DVD+RW formatted media. (Some DVD+R and DVD+RW media brands

might not be compatible.)

In addition to this Software and User Guide CD, you should have received the following:

v ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive

v Carrying case

v Laser Safety Guide

v Quick Reference Guide

Note:

Your kit might also contain a software update disc.

Contact your place of purchase if an item is missing or damaged. Be sure to retain your proof of

purchase. It might be required to receive warranty service. See Appendix A, “Service and Support,” on

page 13 for technical support information.

Software description

The Software and User Guide CD contains the following software:

v Creator Business Edition

Creator Business Edition is disc mastering software that allows you to create your own music or data

discs from files on your computer, or from other disc media such as CDs or DVDs. Music discs created

with Creator Business Edition can play on any CD player, whether it is at home, in your car, or

through the CD-ROM of your computer. Creator Business Edition also makes it easy to create data

discs that can be read on any appropriate CD or DVD disc reader.

Creator Business Edition guides you, step-by-step, through the recording process with simple wizards

and an intuitive user interface.

v Intervideo WinDVD

This software enables you to play back DVD videos on your computer or to play video files from your

hard disk drive.

v Drag-to-Disc (DLA)

This software enables you to write directly to CD-RW media by using the drive letter, just as you

would write to a diskette. All disc format types can be formatted by DLA. With DLA, you can drag

and drop files, create new directories, or save files from any application directly to your Ultrabay Serial

ATA Drive.

v UDF Reader

This software enables you to read DLA-created discs on systems with a read-only CD or DVD drive.

Installation requirements

To install the CD-RW/DVD-ROM Ultrabay Serial ATA Drive, your ThinkPad computer must meet the

following requirements:

v ThinkPad system with Ultrabay bay

v ThinkPad X200 Ultrabase (9.5 mm drive only)

v Microsoft

®

Windows

®

2000 Professional, Microsoft Windows XP, or Microsoft Windows Vista

®

operating system

Note:

Lenovo

®

offers limited support for computers with Microsoft Windows 95, Microsoft Windows 98,

Microsoft Windows Millennium Edition (Me), or Microsoft Windows NT

®

Desktop operating

systems.

Installing the drive

Your ThinkPad computer includes a help system, Access ThinkPad, which provides drive installation

instructions specific to your computer. To correctly install the CD-RW/DVD Ultrabay Serial ATA Drive

into the Ultrabay bay, use the instructions provided in the Access ThinkPad help system.

Locating the drive controls

Refer to the ThinkPad user guide for instructions on locating the drive controls.

2 ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

Chapter 2. Using the ThinkPad CD-RW/DVD-ROM Ultrabay

Serial ATA Drive

This section provides information on how to handle, load, and care for DVDs and CDs, as well as how to

care for your CD-RW/DVD-ROM Ultrabay Serial ATA Drive.

Before you begin

For best results, review the following guidelines before using the drive:

v Do not move your ThinkPad computer while formatting or writing to a disc as this might cause data

errors. Also, minimize typing while formatting or writing to a disc, as this might also cause data errors.

v Keep the ThinkPad computer on a flat surface when writing to a disc.

v Make sure your ThinkPad computer is plugged into an ac outlet when using the drive. The disc might

be damaged if the battery runs out while writing to a disc.

v Turn screen savers off. Using a screen saver might interrupt the formatting and writing process.

v Do not put your ThinkPad computer into hibernation or suspend mode while writing to a disc.

Note:

The read and write results of the drive depend upon the quality and characteristics of the DVD or

CD media used.

Handling and caring for a disc

Carefully handle and clean discs, especially writable media types such as CD-R and CD-RW discs, so that

they remain readable. You can prolong the life of your discs by observing the following precautions:

v Always store discs in their original packaging

v Always store discs out of direct sunlight

v Always store discs away from direct heat sources

v Remove discs from the computer when not in use

v Check disc for cracks before each use

v Do not force discs into the computer or packaging

v Do not bend or flex discs

IMPORTANT:

Do not use discs that are cracked.

Attention: Wiping a disc using a circular motion can cause data loss.

v Handle a disc by the edges or the center hole. Do not touch the surface of a disc.

v To remove dust or fingerprints, wipe a disc from the center to the edge with a soft, lint-free cloth.

v Do not write on the surface of a disc.

v Do not place a disc in direct sunlight.

v Do not use commercial cleaners to clean a disc.

v Do not bend a disc.

Caring for the CD-RW/DVD-ROM Ultrabay Serial ATA Drive

To protect your drive during operation, observe the following precautions:

v Remove the disc from the drive before moving the drive.

v Do not insert foreign objects into the drive.

v Do not stack objects on the drive.

v Do not remove the drive cover or attempt to service the drive.

v Do not operate the drive under any of the following conditions:

– High temperature, high humidity, or direct sunlight

– Excessive vibration, sudden shock, or inclined surface

– Excessive dust

Loading a disc

1. Press the Eject button. The tray slides out of the drive.

2. Place a disc in the tray with the label facing up.

3. Close the tray by gently pushing the tray in until it latches.

Attention: Do not use force or insert foreign objects to open the tray. If your tray does not open when you press the

Eject button, see “Manually ejecting a disc” for more information.

Manually ejecting a disc

If you press the Eject button and the tray does not slide out, turn off the computer and straighten a large

paper clip to form a tool, as shown in the illustration. The straightened end must extend at least 45 mm

(1.8 inch). Insert the extended end into the manual-eject hole on the front of the drive. Push the paper

clip until the tray opens. Gently pull out the tray until you can remove the disc.

4 ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

45 mm

1.8 in

Using CD-R and CD-RW discs

The CD-RW/DVD-ROM Ultrabay Serial ATA Drive can write to both CD-R and CD-RW discs. CD-R

discs cannot be erased, but can be used with standard CD-ROM drives and CD players.

You can use CD-R discs to record audio tracks, store data, archive files, and copy files from another CD.

CD-RW discs can be erased and rewritten, but can be used only with newer CD-RW-compatible CD-ROM

and DVD-ROM drives. You can use CD-RW discs to back up, store, and update files or to copy files from

another CD.

Notes:

1. CD-R discs are playable on audio CD players. CD-RW discs are not playable on most audio CD

players.

2. The software included with this drive does not enable the drive CD-recording capabilities with DOS,

Windows 3.x, or OS/2

®

operating systems.

For more information on using the software, refer to “Using Drag-to-Disc (DLA)” on page 7 and “Using

Creator Business Edition” on page 8.

Installing software

After you have connected the ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive, you can install

application software from the Software and User Guide CD. There are four software packages on the CD:

v Creator Business Edition – Install this software to record CDs.

v Intervideo WinDVD – Install this software to play DVD videos.

v Drag-to-Disc – Install this software to write directly to CD-RW media using your ThinkPad

CD-RW/DVD-ROM Ultrabay Serial ATA Drive, just as you would write to a diskette.

v UDF Reader – Install this software on your Windows operating system computer to read discs created

with Drag-to-Disc.

Notes:

1. Do not install both Drag-to-Disc and the UDF Reader on the same computer. Drag-to-Disc is installed

to read and write in your computer, while the UDF Reader is provided so other systems can read

Drag-to-Disc media made in your computer.

2. Drag-to-Disc and the UDF Reader have both 32 and 64 bit versions. Install only the one that matches

your operating system.

Complete the following steps to install the application software:

1. Insert the Software and User Guide CD into the CD or DVD drive. If the CD starts automatically, go to

Step 4.

2. If the CD does not start automatically, click Start and then click Run.

3. In the Open field, type x:\launch.bat where x is the drive letter of the CD or DVD drive.

4. If you get a warning from Internet Explorer

®

about malicious scripts, right-click the warning bar, and

select Allow Blocked Content.

5. Select Software from the left-hand navigation bar.

6. Check the boxes by the software applications that you wish to install.

Chapter 2. Using the ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive 5

7. Click Go. The software you selected will install silently.

8. Restart your computer after the completion message.

Note: If the software fails to install silently, you can select individual packages from the bottom line of

the Installation page and install the packages following instructions on your screen.

Using Intervideo WinDVD

If the operating system of your computer is Windows Vista Home Premium or Windows Vista Ultimate,

you can view DVD movies without installing any additional software. Windows Media

®

Player comes

fully configured to play DVD videos in those operating system versions. In Windows Vista Ultimate, you

can also use Windows Media Center to view DVD videos.

If the operating system of your computer is Windows XP, Windows Vista Business, or Windows Vista

Home Basic, you must install WinDVD to play back DVD videos.

If you are using a legacy operating system on your computer, you might need to update some

components of your operating system to enable the DVD video playback function. The requirements for

legacy operating systems are as follows:

v Windows 95, Windows Server

®

2000, Windows Server 2003: You must install the latest service pack,

Internet Explorer 5, and DirectX

®

.

v Windows 98, Windows 98 Second Edition, Windows Millennium Edition: You must install the latest

DirectX.

v Windows 95 OEM Service Release 2 (OSR2): You must install Internet Explorer 5 and DirectX.

v Windows 2000: You must install Service Pack 2 or higher, and DirectX.

v Windows NT: You must install Service Pack 6 along with Internet Explorer 5, DirectX, and a third

party IDE DMA driver. DirectX is not available in Windows NT due to Microsoft no longer providing

any official DirectX for Windows NT.

Installing WinDVD and viewing a DVD movie

To install WinDVD, go to the Software page of the Software and User Guide CD. Select WinDVD from the

available software list. Restart your computer after installation.

After you install the CD-RW/DVD-ROM Ultrabay Serial ATA Drive and WinDVD, you can view a DVD

movie. But first you need to set the DVD region code for your DVD content.

DVD region codes

DVD region codes help protect the contents of a DVD. The world is divided into six regions and specific

content can be viewed only in the appropriate region. For example, content for Region 1 can be viewed

only in the U.S. and Canada. WinDVD is also region–specific.

You can verify the region code of the content by looking at the region code symbol on the back of the

content packaging.

Region code Region

1 U.S., Canada

2 Europe, Middle East, South Africa, Japan

3 Southeast Asia, Taiwan, Korea

4 Latin America, Australia, New Zealand

5 Former Soviet Union, North Africa, India

6 People’s Republic of China

6 ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

Start WinDVD by inserting the DVD into the drive. The region code is automatically set and you can

view the movie. This is the initial setting.

After the region code has been set, if you insert a DVD with a different region code, you are prompted to

change the region code. You can change the region code from your initial setting up to four times.

After the region code has been changed from its initial setting four times, it is fixed and can no longer be

changed. Thereafter, you can play DVD content only from that region.

To display the region code status, click the WinDVD Properties button on the WinDVD user interface.

The General tab contains this information.

Starting WinDVD

To start WinDVD, click Start -> Programs -> Intervideo WinDVD.

For more information on how to play the DVD movie player, refer to the WinDVD help information on

the Software and User Guide CD. If you want to watch a DVD movie on your TV, refer to the online

information provided with your computer.

Notes:

1. Your computer has been configured to provide the highest quality audio and video playback

obtainable with the available system resources. You can alter the default settings by changing the

video resolution setting within the Control Panel. Some systems do not have enough resources to

provide full-quality audio and video playback at all resolution settings. If you experience poor

playback performance, adjust the resolution to a lower setting.

2. Audio and video streams are decoded by software. The audio and video subsystems need to be fully

functional and enabled.

3. WinDVD does not enable DVD playback feature through Windows Media Player. After installing

WinDVD, DVD video may play back through Media Player, but audio will not.

Using Drag-to-Disc (DLA)

Drag-to-Disc (DLA) is provided so that you can write data to CD-RW media. CD-RW media can be

written to many times. You can access Drag-to-Disc from the Multimedia Center or from My Computer.

To use DLA-formatted media from within the Creator Business Edition:

1. Start the Multimedia Center.

2. Select the Data tab.

3. Select the task Drag-to-disc.

4. Format your disc or add data as desired.

To format and write to CD-RW media from My Computer:

1. Insert a disc into the drive.

2. Double-click My Computer. Right-click the drive letter for the Ultrabay Serial ATA Drive.

3. Click Format. Formatting time will vary depending on the format process you use (quick or full).

4. After formatting is complete, you can drag and drop files to the Ultrabay Serial ATA Drive icon, or

you can move files in Windows Explorer.

A UDF Reader is included on the Software and User Guide CD. To use the UDF Reader to read UDF

formatted CD-RW media, complete the following steps:

1. Insert the Software and User Guide CD into the drive of the computer you want to use the UDF

formatted discs with.

2. Select Software from the side menu.

Chapter 2. Using the ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive 7

3. Select the UDF Reader for installation.

4. Restart the system.

Note: The UDF Reader is not required on any computer that has DLA installed. It is only used on

computers that share media with computers that write with DLA.

Using Creator Business Edition

With Creator Business Edition you can create:

v Exact copies of existing discs: The Exact Copy feature makes a duplicate of your master disc,

transferring the disc layout of the original disc to your CD-R or CD-RW.

v Discs of archived data from your hard disk drive: The Make a Data disc feature is used to store

electronic data, such as the files and applications that reside on your computer’s hard disk drive.

Unlike music discs, data discs are used to store files that are readable only by a computer, and cannot

be played on your home or car stereo, even if audio files are on the disc.

v Music compilations from WAV, MP3, or WMA files, or from existing music discs: The Make a Music

disc feature creates custom music discs from files on your hard disk drive or your existing music discs.

The CD music database feature can automatically tag your files with track information to help you sort

through your collection.

Also, you can create images of your CDs and DVDs on your hard disk drive and burn saved CD images

to discs.

Note: Refer to the Creator Business Edition Online Help for more information on how to make an exact

copy, create a data disc, or create an audio disc with Creator Business Edition.

To start Creator Business Edition, click Start -> Programs -> Creator Business Edition to open the main

recording software window.

Backing up a CD

To copy a commercial CD, you must own the copyright or obtain permission from the copyright owner. If

you do not own the copyright or do not obtain permission from the copyright owner, you might be

violating copyright law and might be subject to payment of damages or other remedies. For more

information on copyright law, consult your legal advisor.

Copying and imaging discs

You can use the Creator Business Edition application to make copies and save images of your CDs. You

can also create CDs from images that you have previously saved on your hard disk drive. The

Multimedia Center can only save images in ISO and GI formats. ISO formats can only be used for data

CDs. All other disc formats require GI images.

Saved CD images might be as large as 730MB. Ensure that you have adequate hard disk drive space

before proceeding.

8 ThinkPad CD-RW/DVD-ROM Ultrabay Serial ATA Drive User Guide

Page is loading ...

Lenovo ThinkPad Series User manual

This manual is also suitable for

Lenovo ThinkPad Series User manual

Related papers

Other documents