Polaroid TLA-01915 User manual

Questions?

Need some help?

This manual should help you

understand your new product.

Or visit

www.polaroid.com/support.

If you still have questions, call

our help line found on the

insert with this icon:

15” / 19” HD LCD TV

Your TV may look different from the one pictured.

This TV incorporates High-Deﬁ nition Multimedia Interface (HDMI

TM

) technology.

HDMI, the HDMI logo and High-Deﬁ nition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

“Polaroid” and “Polaroid and Pixel” are trademarks of Polaroid Corporation.

Changes are periodically made to this document. Changes, technical inaccuracies, and

typographic errors will be corrected in subsequent editions.

For service, support and warranty information, visit www.polaroid.com.

This product contains electrical or electronic materials. The presence of these materials may,

if not disposed of properly, have potential adverse effects on the environment and human

health. Presence of this label on the product means it should not be disposed of as unsorted

waste and must be collected separately. As a consumer, you are responsible for ensuring that

this product is disposed of properly. To ﬁ nd out how to properly dispose of this product, please

go to www.polaroid.com and click on “Company“ or call the customer service number for your

country listed in the instruction manual.

Digital Television Transition Notice:

This device contains a digital television tuner, so it should receive digital over the air TV program-

ming, with a suitable antenna, after the end of full-power analog TV broadcasting in the United States

on February 17, 2009. Some older television receivers, if they rely on a TV antenna, will need a TV

Converter to receive over the air digital programming, but should continue to work as before for other

purposes (e.g., for watching low-power TV stations still broadcasting in analog, watching pre-recorded

movies, or playing video games). When a Converter is used with an older television receiver, a signal

splitter might be necessary to continue to receive low-power analog broadcasts via an antenna. For

more information, please see www.DTV.gov. For information on the TV Converter program, and on

government coupons that may be used toward the purchase of one, see www.dtv2009.gov, or call the

NTIA at 1-888-DTV-2009.

ENGLISHENGLISH

1

FCC

Federal Communications

Commission Statement

This equipment has been tested and found to comply with the limits of a class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

1. Reorient/Relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit which is different from what the receiver is

connected to.

4. Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the manufacturer

responsible for compliance could void the user authority to operate the

equipment.

ENERGY STAR® qualiﬁ ed TV

The factory default settings allow your TV to be Energy Star compliant. If

you adjust the settings of your TV, increasing the brightness for instance,

your TV may consume more energy than what is deﬁ ned by the Energy

Star program. For more information on Energy Star, please visit www.

energystar.gov.

2

Warnings and Precautions

To reduce the risk of ﬁ re or electric shock, do not expose this equipment to rain or moisture.

This symbol is intended to alert the user to avoid the risk of electric shock.

This equipment must not be disassembled by anyone except qualiﬁ ed service personnel.

This symbol is intended to alert the user to the presence of important operating and

maintenance instructions in the literature accompanying the appliance.

▪ TO REDUCE THE RISK OF ELECTRIC SHOCK,

▪ DO NOT REMOVE COVER (OR BACK).

▪ NO USER-SERVICEABLE PARTS INSIDE.

▪ REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Use of controls, adjustments or performance of procedures other than those speciﬁ ed herein

may result in hazardous radiation exposure.

CAUTION

Important Safety Instructions

To prevent any injuries, the following safety precautions should be observed in the installation, use,

servicing and maintenance of this equipment.

Before operating this equipment, please read this manual completely, and keep it nearby for future

reference.

WARNING

▪ Do not place the equipment on any uneven or unstable carts, stands, tables, shelves etc.

The equipment may fall, causing serious injury to children or adults and serious damage to

the equipment itself.

▪ Use only a cart or stand recommended by the manufacturer. This equipment and

recommended cart or stand should be handled with care. Quick stops, excessive force, and

uneven surfaces may cause the equipment and cart/stand to overturn.

▪ Do not disable the 3-wire grounding type plug. The grounding pin on the 3-prong plug is an

important feature. Removing the grounding pin will increase the risk of damaging the

equipment.

▪ If you can not ﬁ t the plug into the electrical outlet, contact an electrician to install a grounding

outlet.

▪ Always operate this equipment from the type of power source indicated on the rear of the

serial/model plate.

▪ Never overload wall outlets and extensions.

This symbol indicates caution points.

This symbol indicates actions that should not be done.

This symbol indicates actions that must be performed.

ENGLISHENGLISH

3

Warnings and Precautions

▪ Use and handle the power cord with care. Do not place any heavy objects on the AC

power cord.

▪ Do not pull the AC power cord. Do not handle the AC power cord with a wet hand.

▪ Do not touch the power cord and antenna cable during lightning.

▪ Remove the plug from the wall outlet, if the equipment will not be used for a long period

of time.

▪ Do not place, use or handle this equipment near water.

▪ Never expose the equipment to liquid, rain, or moisture.

Seek for service if any of the above is spilled into the equipment.

▪ Do not expose the equipment to extreme temperature or to direct sunlight, as the

equipment may heat up and suffer damage.

▪ Do not install the equipment near any heat sources such as radiators, heat registers,

stoves, or any other apparatus that might produce heat.

▪ Do not attempt to service the equipment yourself.

▪ Opening and removing the covers may expose you to dangerous voltage or other

hazards and may void your warranty. Refer service to qualiﬁ ed personnel.

▪ Do not place or drop any other objects on top.

▪ Do not insert anything into the ventilation holes of your equipment.

Inserting any metal or ﬂ ammable objects may result to ﬁ re or electric shock.

▪ Protect the power cord from being walked on or pinchrd particularly at plugs ,convenience

receptacles, and the point where they exit from the apparatus.

▪ Do not place the equipment on uneven or unstable carts, stands, tables, shelves etc. The

equipment may fall, causing serious injury to children or adults and serious damage to

the equipment itself.

Always place the equipment on the ﬂ oor or on a surface that is sturdy, level, stable and

strong enough to support the weight of the equipment.

▪ Do not block any ventilating openings. Leave an open space around the equipment.

Never place the equipment :

on a bed, sofa, rug, or any other similar surfaces; too close to drapes/curtains/walls, in a

bookcase, built-in cabinet, or any other similar places that may cause poor ventilation.

▪ Unplug this apparatus during lightning storms or when unused for long periods of time.

▪ Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

▪ Always remove the power cord from the outlet before cleaning the equipment.

▪ Never use liquid or aerosol cleaners on the equipment.

Clean only with a soft dry cloth.

▪ Only use attachments/accessories specified by the manufacturer.

4

Warnings and Precautions

Outdoor Antenna Safety Instructions

Antenna lead-in wire

Antenna discharge unit

(NEC section 810-20)

Grounding conductors

(NEC section 810-20)

Ground clamps

Power service grounding

(NEC Art250 part H)

Ground clamps

Electric service

equipment

NEC : National Electrical code

If an outdoor antenna is connected, follow the precautions below:

EXAMPLE OF OUTDOOR ANTENNA GROUNDING

Section 810 of National Electrical Code (NEC) provides information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding

conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for

the grounding electrode.

▪ An outdoor antenna should not be located in any area where it could come in contact with

overhead power lines, or any other electric light or power circuits.

▪ When installing an outdoor antenna system, extreme caution should be taken to prevent

contact with power lines. Direct contact with power lines may be fatal and should be avoided

at all costs.

ENGLISHENGLISH

5

TABLE OF CONTENTS

Federal Communications Commission Statement .......................... 1

Warnings and Precautions

Important Safety Instructions ....................................................................................... 2

Antenna Safety Instructions ......................................................................................... 4

Chapter 1 Introducing the LCD TV

Key Features ............................................................................................................... 6

Package Contents ....................................................................................................... 7

Setting Your LCD TV .................................................................................................... 8

Your Remote Control ..................................................................................................11

Chapter 2 Installing the LCD TV

Connecting a TV Cable or an Antenna ...................................................................... 13

Connecting an A/V Device with Composite Connector .............................................. 18

Connecting an A/V Device with S-Video Connector .................................................. 19

Connecting an A/V Device with Component(YPbPr) Connector................................ 20

Connecting an AV Equipment with HDMI Connector ................................................. 21

Connecting an AV Equipment with DVI Connector .................................................... 22

Connecting a PC........................................................................................................ 23

Connecting an Audio Receiver or a Dolby Digital 5.1 Sound System........................ 24

Chapter 3 Using The Features

Wide Screen Viewing ......................................................................................25

Using the Program Guide ................................................................................26

Operating the Menu ........................................................................................ 27

Customizing the VIDEO Settings ......................................................................28

Customizing the AUDIO Settings ...................................................................... 31

Customizing the TV Settings ............................................................................33

Customizing the SETUP Settings......................................................................35

Using the Parental Control Settings ..................................................................38

Speciﬁ cations ........................................................................................................ 43

6

Chapter 1 Introducing the LCD TV

Various Audio/Video terminals for external equipment connection

▪ 1 composite VIDEO input terminal

▪ 1 S-VIDEO terminals

▪ 1 sets of component Video input terminals

▪ 1 PC(VGA IN)/PC AUDIO IN input terminals

▪ 1 HDMI input terminal

▪ 1 set of Audio(L/R) output terminals for composite C-VIDEO/S-VIDEO

▪ 1 COAXIAL output terminal

▪ 1 Headphone terminal

The built-in TV tuner to receive HD ATSC signal

▪ This function allows the reception of HD broadcasting without the addition of a set top

box.

High Definition Multimedia Interface (HDMI)

▪ High Deﬁ nition Multimedia Interface (HDMI) is a small, user-friendly interconnect that

can carry up to 5 Gbps of combined video and audio in a single cable. This system

eliminates the cost, complexity and confusion of multiple cables used to connect

current A/V systems.

HDTV Component Video Inputs

▪ Offers the best video quality for DVD(1080i, 720p) and digital set-top-box (1080i, 720p)

connections.

2D Digital Noise Reduction

▪ This function can digitally reduce image noise to provide better picture quality.

Film-Mode Detection

▪ This function can automatically detect content derived from ﬁ lm and adjust the

interlacer’s frame matching to provide a more natural-looking, clearer image of the

moving picture.

Chapter 1

Introducing the LCD TV

Key Features

ENGLISH

7

Chapter 1 Introducing the LCD TV

Make sure all of the above contents are included in the package. If you are missing

any items, please contact customer service.

 LCD TV

Make sure all of the following contents are included.

 Power Cord

These items are all you need to set up and operate the LCD TV in its basic conﬁ guration.

Package Contents

 Remote Control/

AAA Batteries x 2

 User’s Manual

 Quick Start Guide

 Warranty Card

S.MODE

MTS

P. MODE

VOL.

CH.

MUTE

INPUT

GUIDE EXIT

INFO MENU

LIST

FAV

.CH

TIMER

FREEZE

P.SIZESLEEPCAPTION

Questions?

Need some help?

This manual should help you

understand your new product.

Or visit

www.polaroid.com/support.

If you still have questions, call

our help line found on the

insert with this icon:

15”/ 19”/ 20”/ 22” HD LCD TV with Digital Tuner

Your TV may look different from the one pictured.

WARRANTY

Your television will be repaired or replaced in accordance with the terms of this warranty, at Proview’s option, if it proves to be defective

in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date

(“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product,

effective only when used in the United States (48 continental states plus Alaska* and Hawaii*) only and only when purchased from an

authorized Proview retailer, including authorized online retailers.

WARRANTY PERIOD:

• LABOR and PARTS : 1 YEAR from the Date of Purchase. Your unit will be repaired or replaced with a new unit, substitute model or

factory reconditioned unit, at Proview’s option. If repaired, parts used in the repair may be new or remanufactured. Replacement Units

and Repair Parts are warranted for the remaining portion of the original unit’s warranty period.

• EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user. KEEP THE

DATED BILL OF SALE as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale when

requesting warranty service. (If a receipt is not available the manufacture date will be used as the purchase date)

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS

LIMITED IN DURATION TO THE EXPRESSED WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR

SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING

WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN

CONTRACT, TORT, OR OTHERWISE

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied

warranty last, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also

have other rights that vary from state to state.

CONCERNING PIXEL FUNCTIONALITY:

Your Television contains millions of individual pixels. These Televisions typically contain a small number of pixels which do not function

normally. Your display has been inspected and is in compliance with the manufacturer’s specifications which indicate that any pixel

defects do not effect the operation or use of your display.

THIS LIMITED WARRANTY DOES NOT APPLY TO:

• Damage caused in shipping or transit

• Image burn-in

• Service required as a result of improper installation, including incorrect or insufficient AC supply (please consult the owner’s manual

for power supply requirements)

• Installation or repair of antenna systems, cable converters, cable company supplied equipment, or other components in a video

system

• Setup or adjustment on consumer controls, or damage caused by improper adjustments

• Damage caused by other system components

• Any panel that has been modified or incorporated into any other product

• Replacement of batteries on the remote control

• Damage (including cosmetic damage), failure, loss or personal injury due to misuse, abuse, negligence, improper maintenance or

storage, or to acts of nature or other causes beyond our control. Causes beyond our control include but are not limited to lightning

strike, power surges, power outages, and water damage, etc

• Repair or replacement of warranted parts by other than Proview authorized service centers

• Units purchased or serviced outside of the coverage area.

• Units purchased as used, open box, clearance or display models

• Product where the original factory serial numbers have been removed, defaced or changed in any way

• Product sold and labeled as “as is, where is” or similar disclaimer

The cost of repair or replacement under these excluded circumstances shall be borne by the

consumer.

FOR SERVICE(all sizes screen):

Before you call for warranty service, check your operating guide under the “troubleshooting” section, this may help you avoid a service

call. For warranty service information, please contact the Proview Customer Interactive Center. Products 32” and under can only be

serviced at an authorized Proview service center .When calling for service, please have your product model number, serial number

and the date of purchase available. If repair is needed on your product, during the limited warranty period the customer is responsible

for the cost of shipping to Proview's service center at the customer's expense. After the product is repaired and tested, the Proview

service center will ship the unit back to the customer within the continental United States (48 states and DC) at Proview's expense.

Proview is not responsible for the de-installation or re-installation of the product. If a replacement unit is required, (subject to availability)

under some circumstances you may be asked to provide a reserve deposit with an advanced replace agreement to the Proview

Service Center against a credit card number as security for advanced shipment. Your credit card will not be charged if you return the

defective unit within 30 calendar days from the date you received the replacement unit.

If a replacement unit is received, please use the original carton and packaging materials for the defective unit in returning the defective

unit to the Proview service center. Parts and labor in accordance with the Proview warranty are Proview’s responsibility and will be

Digital HD LCD TV

C

H

E

C

K

t

o

m

a

k

e

s

u

re

a

l

l o

f t

h

e

c

o

n

t

e

n

ts

a

re

i

n

t

h

e

b

o

x

R

E

V

IE

W

t

h

e

s

a

f

e

t

y

i

n

f

o

r

m

a

t

i

o

n

in

t

h

e

U

se

r’

s

M

a

n

u

a

l

S

E

T

U

P

y

o

u

r H

D

T

V

s

o

th

a

t

th

e

re

a

r

c

o

n

e

c

t

o

r

s

a

r

e

a

c

e

ss

i

b

l

e

IN

S

T

A

L

i

n

c

lu

d

e

d

A

b

a

t

e

r

ie

s

in

t

o

t

h

e

p

r

o

v

id

e

d

P

o

la

r

o

i

d

R

e

m

o

t

e

C

o

n

tr

o

l

W

R

IT

E

d

o

w

n

yo

u

r

H

D

T

V

’s

M

o

d

e

l

a

n

d

S

e

r

ia

l N

u

m

b

e

r

(

lo

c

a

t

e

d

o

n

th

e

b

a

c

k

o

f T

V

)

QUICK

START

GUIDE

Component In

Cable/

Antenna

Audio InS-Video InComposite In 2

RR

R

L

Pr

Pb

Y

Audio VideoL

SP/DIF

VGA (D-SUB)

PC

Audio In

Audio Out RS232

HDMI

R L Subwoofer

T

HREE W

A

YS TO

GET HD

TV

1) OVER-THE-AIR HD ANTENNA – Connected to your HDTV through RF Cable /

Antenna input.

2) HD CABLE BOX – Subscribe to HD programming through your local cable company

(HD cable box required).

3) HD SATELLITE – Subscribe to HD programming through DirecTV, Dish Network,

or other satellite provider (HD satellite receiver required).

For more information, see the “Installing the LCD TV” in your User’s Manual.

FO

UR E

AS

Y S

TE

PS

FOR

CON

NEC

T

IN

G YO

U

R H

D

TV

1) CHOOSE A/V EQUIPMENT YOU WANT TO CONNECT TO YOUR HDTV

Select which types of A/V Equipment and TV Signal Sources you want to connect to

your HDTV.

The colored boxes in the A/V Equipment and TV Signal Sources charts below indicate which

type of connections you may use to connect to your HDTV

Need help connecting your A/V equipment to your Polaroid HDTV? Visit http://ceaconnectionsguide.com for an interactive connectivity tool.

HDMI: THE BEST CONNECTION

We highly recommend you use the HDMI input

whenever possible to receive an incredible High

Definition picture. Please keep in mind, however,

that not all A/V devices are capable of this type

of connection.

For the best viewing experience, connect your TV

to an HD digital cable/ satellite box, HD/ Blu-Ray

DVD player and/or other HD A/V device using

the HDMI connection. Make sure your external

A/V devices are set to output an HDMI signal.

Consult your A/V device’s User’s Manual for

instructions on how to output an HDMI signal.

*HD-CAPABLE CONNECTION

2) CHOOSE A/V

CONNECTION METHODS

Using the colored boxes from STEP

ONE, follow the row across to STEP

TWO to match up the colored boxes to

the same colored connection method.

Choose ONLY one connection method

for each signal and piece of equipment.

3) SELECT CABLES AND MAKE CONNECTIONS

Once you have chosen your preferred connection methods from STEP TWO,

follow the row to STEP THREE to decide what kind of cables you need and

what the connections look like on your A/V equipment.

Following the color-coded chart, use the appropriate cables and connect

yourTV Signal Source and A/V Equipment to the color-coded inputs on

your HDTV. (Refer to the Connection Map at the bottom of the page.)

Once connected, turn on your HDTV and all your connected A/V equipment.

4) ENJOY

YOUR HDTV!

Follow the

“PROGRAM YOUR

HDTV”section on

the back of this

Quick Start Guide.

Cable Box

Digital Cable Box

Satellite Box

TV SIGNAL SOURCEA/V EQUIPMENT

CONNECTION METHODS

Cable

(Without Box)

Antenna

DVD

DVR

Computer

Game System

Sound System

VCR

Digital Camera

HDMI

COMPONENT

CABLE / ANTENNA

VGA (D-SUB)

PC ONLY

S-VIDEO

COMPOSITE

MY A/V

EQUIPMENT HAS

MY POLAROID

HDTV HAS

CABLES

NEEDED

Video Camera

OR

HDMI

COMPONENT

CABLE / ANTENNA

VGA (D-SUB)

PC ONLY

S-VIDEO

COMPOSITE

G

O

D

>

B

E

T

E

R

>

B

E

S

T

Questions? Need help connecting your HDTV?

Consult your user’s manual or give us a call. Our helpful

customer service will answer all your questions.

Look for the insert with this icon:

Or visit www.polaroid.com.

"Polaroid" and "Polaroid and Pixel" are trademarks of Polaroid Corporation.

Product features, specifications, and appearances are subject to change without notice.

20080501

CONTENTS

Power Cord Remote Control & AAA Batteries

Screen Cloth User’s Manual, Warranty Card

and Quick Start Guide

 Screen Cloth

8

Chapter 1 Introducing the LCD TV

Do not use caustic cleaners (porcelain, stainless steel, toilet, or oven

cleaner etc.) on the remote, as it may suffer damage.

 Use a supplied antenna cable to connect the VHF/UHF signal to the LCD TV’s ANT.

terminal.

 Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.

 Insert the 2 batteries supplied in remote control.

 Connect other an external AV device.

Step1 Slide the back cover up to open the

battery compartment of the remote

control.

Step2 Insert two AAA size batteries.

Make sure to match the (+) and

( - ) ends of the batteries with

the (+) and ( - ) ends indicated

in the battery compartment.

Slide the cover back into place.

How to setup the TV

Your LCD TV

Front View

Right/Left Side View and Controls

IR

Infrared Receiver

LED

The LED light indicates when the LCD TV is activated.

MENU

Press once to display the OSD

(on screen display), press again

to turn the OSD off.

VOL

+/VOL-

Adjusts the volume up and

down. Selects the main-menu

item and change values for

items when in the OSD mode.

Turns the LCD TV on and into

standby mode.

CH+/CH-

Scans up and down through

channels. Selects sub-menu

item when in the OSD mode.

INPUT

Chooses from different input

signal sources.

HEADPHONE

Connects to the external

headphone for private

listening.

Left SideRight Side

ENGLISH

9

Chapter 1 Introducing the LCD TV

HDMI IN

LRLR

PC/VGA IN

PC AUDIO IN

VIDEO IN S-VIDEO IN

COAXIAL

VHF/UHF IN

YPbPr

AUDIO IN

10

Chapter 1 Introducing the LCD TV

Rear View and Jacks

VHF/UHF IN

Connects RF input from VHF/UHF antenna or cable

to receive high/standard deﬁ nition television.

COAXIAL

Connects to the audio jack on the digital/standard 5.1 audio system.

HDMI IN

Connects the all digital AV equipment with HDMI

connector.HDMI supports enhanced, high-deﬁ nition

video and two-channel digital audio.

PC/VGA IN/ PC AUDIO IN

Connects the PC, or other AV

equipment with VGA and AUDIO

output jacks.

S-VIDEO/VIDEO/AUDIO(L/R) IN

Connects to the S-Video/Composite VIDEO and AUDIO(L/

R) output jacks on external video equipment.

YPbPr IN/AUDIO(L/R) IN

Connects to the DVD player, Digital Set-Top-Box, or

other AV equipment with component(YPbPr) video

and audio output jacks.

AC IN

Connects to the AC power cord.

S.MODE

MTS

P. MODE

VOL.

CH.

MUTE

INPUT

GUIDE EXIT

INFO MENU

LIST

FAV.CH

TI

MER

F

RE

EZ

E

P.SIZESLEEPCAPTION

ENGLISH

11

Chapter 1 Introducing the LCD TV

Your Remote Control

3

9

2

1

8

12

Turns the LCD TV on and off.

MTS Cycles through the multi-channels TV

sound(MTS) options: SAP/MONO/

STEREO

S.MODE Selects sound effect options: Surround/

Live/Dance/Techno/Classic/Soft/Rock/

Pop/Off.

P. MODE Selects picture mode: Vivid/Hi-Bright/

Cinema/Sport/User

P. S I Z E Cycles through Wide mode settings :

NORMAL /FULL/WIDE/ZOOM

CAPTION Cycles through the Closed Caption:

 Anlalog Closed Caption:CC1/CC2/

CC3/CC4/TT1/TT2/TT3/TT4/Off

 Digital Closed Caption:Service1/

Service2/Service3/Service4/Service5/

Service6/Off

SLEEP Cycles through the LCD TV sleep timer:

OFF/10/20/30/40/50/60/90/120 mins

0-9 Select and switch to a channel by using

0-9 buttons.

 In HDTV mode, use with 0-9 and 

buttons to select a digital channels.

JUMP Returns to previously selected channel.

MUTE Mutes and restores the audio

VOL.+- Increases and decreases volume.

CH.+- Scans up and down the channels

1

2

3

4

5

6

7

8

9

10

11

12

4

5

6

7

10

11

3

2

1

8

12

4

5

6

7

10

11

S.MODE

MTS

P. MODE

VOL.

CH.

MUTE

INPUT

GUIDE EXIT

INFO MENU

LIST

FAV.CH

TI

ME

R

F

RE

E

Z

E

P.SIZESLEEPCAPTION

Effective range:

The remote can control the LCD TV from up to 5m away, if pointed directly at the receiver.

13

14

15

16

17

18

19

20

21

22

23

GUIDE Displays the Program Guide on the

screen. Pressing again to turn GUIDE off.

EXIT Exits the OSD menu.

▲▼►◄ Cycles through OSD options and

OK selects individual menu items.

OK conﬁ rms option settings.

INFO Pressing repeatedly displays a variety of

information such as the current channel

and the input source.

MENU Displays the OSD menu on the screen.

GREEN In Program Guide, press to select ﬁ rst

program of next day.

RED In Program Guide, press to select ﬁ rst

program of previous day.

YELLOW In Program Guide, press to view previous

page of detailed program description.

BLUE In Program Guide, press to view next page

of detailed program description.

LIST Displays the received channel list

INPUT Pressing INPUT displays the source list,

use ▲▼ to select the video equipment

connected to the video inputs of your

LCD TV : TV/VIDEO1/VIDEO2/VIDEO3/

VIDEO4/COMPUTER

Input Source

 TV(CABLE/AIR)

VIDEO1 (AV)

VIDEO2 (S-VIDEO)

VIDEO3 (YPbPr)

VIDEO4 (HDMI)

COMPUTER(VGA)

Channel List

7-1 KABC-DT

9-1 KQED-HD

9-2 KOED-SD

8 CCT

12

13

15

FAV.CH Pressing FAV.CH display favorite channels.

FREEZE In TV mode, pressing FREEZE to freeze

the current picture, press again to restore

the picture.

TIMER Displays the current time on the screen.

16

14

13

17

15

18

22

25

24

20

19

26

23

21

24

25

26

12

Chapter 1 Introducing the LCD TV

ENGLISH

13

Chapter 2 Installing the LCD TV

Chapter 2

Installing the LCD TV

Refer to the owner’s manual of any external equipment to be connected.

When connecting any external equipment, do not connect any AC power cords to wall outlets

until all other connections are completed.

Antenna Connection

The antenna requirements for good color TV reception are more important than those for a black &

white TV reception. For this reason, a good quality outdoor antenna is strongly recommended.

The following is a brief explanation of the type of connection that is provided with the various antenna

systems.

75-ohm coaxial cable (round)

F-type connector

300-ohm twin-lead cable (flat)

■ A 75-ohm system is generally a round cable (not included) with F-

type connector that can easily be attached to a terminal without

tools.

■ A 300-ohm system is a flat twin-lead cable (not included) that can

be attached to a 75-ohm terminal through a 300-75-ohm adapter

(not included).

Connecting a TV Cable or an Antenna

14

Chapter 2 Installing the LCD TV

OUT

IN

300-ohm twin-

lead cable

300-ohm twin-

lead cable

75-ohm

coaxial cable

UHF

Antenna

VHF

Antenna

Combiner

(not included)

A. Combination VHF/UHF antenna

300-ohm twin-

lead cable

75-ohm

coaxial cable

VHF/UHF

Antenna

VHF/UHF

Antenna

300/75-ohm adapter

(not included)

B. Separate VHF and/or UHF antennas

Use one of the following two diagrams when connecting an outdoor antenna.

A: Shows how to use a VHF/UHF combination outdoor antenna.

B: Shows how to use a separate VHF and/or UHF outdoor antenna.

ENGLISH

15

Chapter 2 Installing the LCD TV

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the

National Electrical Code (NEC) that provides guidelines for proper grounding and, in particular,

speciﬁ es that the cable ground shall be connected to the grounding system of the building

accurately, or as close to the point of cable entry as possible. Use of this TV for other than

private viewing of programs broadcasted on UHF, VHF or transmitted by cable companies for

the use of the general public may require authorization from the broadcast/cable company, and/

or program owner.

A

IN

B

OUT

Cable TV Line

2 set signal

splitter

(not included)

RF switch

(not included)

Cable TV converter/

descrambler

(not included)

Cable TV (CATV) Connection

■ The RF switch (not included) is required to provide two inputs (A and B). Setting

the RF switch to position A allows viewing of all unscrambled channels by using

the TV channel keys.

■ Setting the RF switch to position B allows viewing of all scrambled channels via

the converter/descrambler by using the converter channel keys.

■ A 75-ohm coaxial cable connector is built into the set for easy hookup.

When connecting the 75-ohm coaxial cable to the set, connect the 75-

ohm cable into the ANT. terminal.

■ Some cable TV companies offer premium pay channels. Since the

signals of these premium pay channels are scrambled, a cable TV

converter/descrambler is generally provided to the subscriber by the

cable TV company.

This converter/descrambler is necessary for normal viewing of scrambled channels.

(Set your TV to channel 3 or 4, typically one of these channels is used. If this is unknown,

consult your cable TV company.)

For more speciﬁ c instructions on installing cable TV, consult your cable TV company.

One possible method of connecting the converter/descrambler provided by your cable TV

company is shown in the diagram below.

VHF/UHF IN

16

Chapter 2 Installing the LCD TV

 Use a supplied antenna cable to connect the TV signal to the LCD TV’s TV CABLE terminal.

 Connect the AC power cord at the back of the TV and connect the power cord to wall outlet.

 Press the button on the remote to turn on the LCD TV.

Always disconnect the LCD TV from the main voltage when the LCD TV will not

be used for a long period of time. The POWER button on the front panel is only

used for switching the LCD TV into standby, it does not disconnect the device

from the main voltage. To completely disconnect the main voltage, please

remove the power plug from the socket.

VHF/UHF IN

ENGLISH

17

Chapter 2 Installing the LCD TV

 Press the button on the remote to turn on the LCD TV.

 Press the Input button on the remote to display the Input List. Use the ▲▼ buttons to select

TV and press the OK button.

 Press the OK button to display the received channel list, then press ▲▼ to select a

channel. Or, use the ▪ with 0-9 buttons to select digital channel( for example 9.1)

The digital main channel might include many subchannels (for example 9-1, 9-

2..) that are showing program at the same time.

The Channel Scanning will create a list of receivable channels for the current

input (antenna or cable). You will be required to run Channel Scanning for each

RF input to create a list of available channels from both inputs.

TV Select Exit

Channel Scan

Tuner Mode Cable

Channel Skip

Favorite List

Time Zone Eastern Time

 Press the MENU button on the remote control to display the Main menu, and use the

◄► buttons to select the TV.

 Press the ▼ button to select Channel Scan, and press the OK button.

The Channel Scan automatically creates a list of receivable channels. Press the MENU

button at any time to interrupt the memorization process.(the list cannot be created if

interrupted)

Status: Scanning..... Cable

Analog Channels: 25

Digital Channels: 0

47%

Input Source

 TV(CABLE/AIR)

VIDEO1 (AV)

VIDEO2 (S-VIDEO)

VIDEO3 (YPbPr)

VIDEO4 (HDMI)

COMPUTER(VGA)

Channel List

7-1 KABC-DT

9-1 KQED-HD

9-2 KOED-SD

8 CCT

12

13

15

Connecting an A/V Device with Composite Connector

HDMI IN

L R

PC/VGA IN

PC AUDIO IN

VIDEO IN S-VIDEO IN

COAXIAL

VHF/UHF IN

YPbPr

AUDIO IN

Rear of TV

AUDIO Cable

AV Cable

L

R

VIDEO OUT

18

Chapter 2 Installing the LCD TV

 Use a composite cable to connect the external A/V device’s composite video/audio jacks to

the LCD TV’s VIDEO IN jacks.

 Connect all AC power sources, before turning on the power switch of the LCD TV or

other connected equipment.

 Press the button on the remote to turn on the LCD TV.

 To view the A/V device’s with component input, press the INPUT button on the remote to

select VIDEO1.

GAME CONSOLE

DVD PLAYER

Not all A/V devices have the ability to connect to a TV. Please check your A/V devices

user guide for compatibility.

Page is loading ...

Polaroid TLA-01915 User manual

This manual is also suitable for

Polaroid TLA-01915 User manual

Related papers

Other documents