Zenith Superdry SD100 Installation Instructions And Operating Manual

Brand: Zenith

Model: Superdry SD100

Type: Installation Instructions And Operating Manual

Superdry Installation & Operating Instructions - 87297 - June 2008 Page 1

Installation Instructions and Operating Procedure

20000NZ Superdry with Cast Alloy White Case SD100

Superdry

Touch-free automatic electric hand dryer

Page 2 Superdry Installation & Operating Instructions - 87297 - June 2008

Key Features

l Warm-air recycling system speeds warm-up, improves thermal efficiency.

l Unique air-directional flap directs air upward for fast face drying.

l Aerodynamic design reduces drying time and power consumption.

l Motor vibration isolation system reduces noise to a minimum.

l Robust diecast alloy case is hard to damage, easy to clean.

l Two overload sensors with automatic motors and element cutoff.

Key Specifications

Model Number SD100

Element 2.2 kW protected by 100°C cutout

Fan Electronically balanced pressed metal

Motor Sealed ball bearing motor with thermal protection

Electrical 220 – 240 AC 50 Hz, 9.8 amps

Air Volume 52 Litres per second

Stop/Start Infra-red electronic sensor

Overheat Cuts out if thermally overloaded

Reset Automatically resets at normal temperature

Cutout Cuts out after 60 seconds if sensor obstructed

Reset Automatically resets when obstruction removed

Case White powder coated alloy diecasting

Height (mm) 252

Width (mm) 287

Depth (mm) 185

Read These Warnings First

Please read all installation requirements, installation procedures and

precautions before installing any Superdry hand dryer.

Never attempt to install any Superdry hand dryer without reading all of the

applicable instructions.

All electrical connections must comply with current wiring rules.

This appliance is not designed for use by young children or infirm people

without supervision.

Young children should be prevented from having access to ensure they are not

able to use or play with the heater.

This appliance must be earthed.

If the power supply cord is damaged it must be replaced by a HydroTap

Company Service Provider or a qualified electrician.

Do not remove the cover of the appliance under any circumstances without

first isolating the appliance from the power supply.

Do not use strong, corrosive or abrasive cleaners to clean the case of the

appliance.

Superdry Installation & Operating Instructions - 87297 - June 2008 Page 3

Installation Instructions

Positioning

The dryer should be positioned on a wall at a suitable height (see table) and

within 900 mm of a standard 220 – 240 AC power outlet rated at 10 amps.

Fastening

Remove the two socket screws on the underside of the dryer.

Lift the lower part of the dryer cover forward about 12 mm then push cover

upward to unlatch top of cover from back plate. Remove earth link from front

wall of case. Place cover in a position away from potential damage.

Position back plate on wall as shown.

Fasten dryer to wall using either four 6 mm toggle bolts (for timber or steel

framed walls) or 6 mm masonry anchors (for masonry walls).

Replace earth link connection to front wall of cover.

Latch top of cover on to back plate, ease base of cover into place, and then

replace screws.

Connecting

Connect dryer to power outlet using the 1 metre cord and plug provided.

Turn power ON.

(For concealed wiring, drill hole for rear cable entry before fixing back plate to

wall, fasten back plate to wall, wire to a 220 - 240 V AC power outlet rated at

10 amps, replace cover before power is turned ON).

Testing

Place hands under dryer to test that dryer turns itself ON.

Withdraw hands from dryer to test that dryer turns itself OFF.

Mens’ washroom 1065 mm

Ladies’ washroom 1015 mm

Child washroom 13-17 years 1015 mm

Child washroom 10-13 years 915 mm

Child washroom 7-10 years 865 mm

Child washroom 4-7 years 760 mm

Disabled washroom 800 mm

Backing Plate Dimensions

Operating Instructions

Drying Hands

Dryer is activated by an infra-red light-emitting diode (electronic sensor).

The sensor is activated by placing hands immediately below dryer.

Fan and heating element are ON only when hands are beneath dryer.

Drying Face

To dry face, tilt the pivoting flap to direct the air stream towards the face.

It is recommended eyes should be closed or protected during face drying.

Maintenance

The dryer case is high strength cast alloy with a white enamel finish.

Regular wiping with a soft cloth and mild detergent will retain its appearance.

Minimum maintenance is required to keep the Superdry in working order.

If the dryer fails to start, check the power supply, if power is ok call a

Service Provider.

Recommended Distance

From Dryer to Base of Floor

262mm

205mm

115mm

183mm

34mm

210mm

248mm

ÿ 44 x 60

cable entry

Floor

38mm

4 x 7 ÿ I.D

bush spacers

Page 4 Superdry Installation & Operating Instructions - 87297 - June 2008

Warranty Information

Head Office

Zenith Heaters Limited,

Unit 2/15 Moselle Avenue,

Henderson.

Auckland. 0610

New Zealand.

www.zenithheaters.co.nz

Telephone: 0800 558055

Facsimile: 0800 559055

Registering your product:

Registering your installation on the Zenith Heaters Limited website may help

to establish date of installation, should it become necessary to service the

appliance, under the terms of the Zenith Heaters Limited warranty. To register

your installation go to www.zenithheaters.co.nz and look under the heading

“Warranty”.

The use of this crossed out wheeled bin logo indicates that this product needs

to be disposed of separately to any other household waste.

Within each of the European Union member countries, provisions have been

made for the collection and recycling of unwanted electrical and electronic

equipment. Outside of the EU it will be necessary to dispose of this product at

your local community waste collection or recycling centre.

In order to help preserve our environment we ask that you dispose of this

product correctly. Please contact your local city council for collection centre

details

As Zenith Heaters Limited policy is one of continuous product improvement,

changes to specifications may be made without prior notice. Images in this

booklet have been modified and may not be true representations of the

finished goods.

Zenith Superdry SD100 Installation Instructions And Operating Manual

Zenith Superdry SD100 Installation Instructions And Operating Manual

Zenith Superdry SD100 Installation Instructions And Operating Manual

Related papers

Other documents