Hotpoint FI6 864 SH IX HA Setup and user guide

Type
Setup and user guide

This manual is also suitable for

1
EN
PRODUCT DESCRIPTION
DAILY REFERENCE
GUIDE
CONTROL PANEL
Read the safety instructions carefully before using the product
1. Control panel
2. Fan
3. Circular heating element
(non-visible)
4. Shelf guides
(the level is indicated on the
front of the oven)
5. Door
6. Upper heating element/grill
7. Lamp
8. Identification plate
(do not remove)
9. Bottom heating element
(non-visible)
1. SELECTION KNOB
For switching the oven on by
selecting a function. Turn to the “0”
position to switch the oven off.
2. BACK
For returning to the previous
settings menu.
3. DISPLAY
4. CONFIRMATION BUTTON
For confirming a selected function
or a set value.
5. ADJUSTMENT KNOB
For scrolling through the menus
and applying or changing settings.
Please note: All knobs are push-
activated knobs. Push down on the
centre of the knob to release it from its
seating.
THANK YOU FOR PURCHASING A HOTPOINT -
ARISTON PRODUCT
To receive more comprehensive help and
support, please register your product at
www.hotpoint.eu/register
Download the safety instructions and the
Use and Care Guide by visiting the
website
docs.hotpoint.eu, and follow the
procedure indicated on the back.
WWW
1 2 3 4 5
5
4
3
2
1
5
4
3
2
1
1
2
3
4
5
8
9
7
6
2
INSERTING THE WIRE SHELF AND OTHER
ACCESSORIES
Insert the wire shelf horizontally by sliding it across
the shelf guides, making sure that the side with the
raised edge is facing upwards.
Other accessories, such as the drip tray and the
baking tray, are inserted horizontally in the same way
as the wire shelf.
REMOVING AND REFITTING THE SHELF GUIDES
. To remove the shelf guides, lift the guides up and
then gently pull the lower part out of its seating:
Theshelf guides can now be removed.
. To refit the shelf guides, first fit them back into
their upper seating. Keeping them held up, slide them
into the cooking compartment, then lower them into
position in the lower seating.
ACCESSORIES
WWW
Download the Use and Care Guide from
docs.hotpoint.eu for more information
WIRE SHELF DRIP TRAY BAKING TRAY
The number of accessories may vary depending on which
model is purchased.
Other accessories can be purchased separately from the
After-sales Service.
3
EN
DIAMOND CLEAN
The action of the steam released during this
special low-temperature cleaning cycle allows dirt
and food residues to be removed with ease. Pour
200 ml of drinking water on the bottom of the oven
and only activate the function when the oven is
cold.
SETTINGS
For changing the oven settings (time,
language, audible signal volume, brightness,
ECOmode, unit of measurement, power).
Please note: When Eco mode is active, the brightness of the
display will be reduced and the light switches o to save
energy. They are reactivated temporarily whenever any of
the buttons are pressed.
SPECIAL FUNCTIONS
MEAT
MEAT
This function automatically selects
the best temperature and cooking method for meat.
This function intermittently activates the fan at
low speed to prevent the food from drying out too
much.
POULT
POULTRY
This function automatically selects the
best temperature and cooking method for poultry.
This function intermittently activates the fan at
low speed to prevent the food from drying out too
much.
CASSE
CASSEROLE
This function automatically selects
the best temperature and cooking method for pasta
dishes.
BREAD
BREAD
This function automatically selects the
best temperature and cooking method for all types
of bread.
PIZZA
PIZZA
This function automatically selects the
best temperature and cooking method for all types
of pizza.
PASTR
PASTRY CAKES
This function automatically selects the
best temperature and cooking method for all kinds
of cakes (leavened cakes, filled cakes, tarts, etc.).
* Function used as reference for the energy eciency
declaration in accordance with Regulation (EU) No. 65/2014
OFF
For switching off the oven.
CONVENTIONAL
For cooking meat or baking cakes with liquid
centre on a single shelf.
CONVECTION BAKE
For cooking meat or baking cakes with liquid
centre on a single shelf.
FORCED AIR
For cooking different foods that require the
same cooking temperature on several shelves
(maximum three) at the same time. This function
can be used to cook different foods without odours
being transferred from one food to another.
GRILL
For grilling steaks, kebabs and sausages,
cooking vegetables au gratin or toasting bread.
When grilling meat, we recommend using a drip tray
to collect the cooking juices: Position the pan on any
of the levels below the wire shelf and add 500 ml of
drinking water.
TURBO GRILL
For roasting large joints of meat (legs, roast
beef, chicken). We recommend using a drip tray to
collect the cooking juices: Position the pan on any
of the levels below the wire shelf and add 500 ml
of drinking water. The turnspit (if provided) can be
used with this function.
MAXI COOKING
For cooking large joints of meat (above 2.5 kg).
Use the 1st or 2nd shelves, depending on the size of
the joint. The oven does not have to be preheated.
We suggest turning the meat during cooking
to obtain uniform browning on both sides. It is
advisable to baste the meat every now and again so
that it does not become too dry.
FAST PREHEATING
For preheating the oven quickly.
ECO FORCED AIR*
For cooking stuffed roasting joints and fillets
of meat on a single shelf. Food is prevented from
drying out excessively by gentle, intermittent air
circulation. When this function is in use, the ECO
light will remain switched off throughout cooking
but can be switched back on temporarily by pressing
.
To use the ECO cycle and therefore optimise power
consumption, the oven door should not be opened
until the food is completely cooked.
FUNCTIONS
4
RISIN
RISING
For optimal proving of sweet or
savoury dough. To maintain the quality of proving,
do not activate the function if the oven is still hot
following a cooking cycle.
WARM
WARM KEEPING
For keeping just-cooked food hot and
crisp.
1. PLEASE SELECT LANGUAGE
You will need to set the language and the time
when you switch on the appliance for the first time:
“ENGLISH” will scroll along the display.
Turn the adjustment knob to scroll through the list of
available languages and select the one you require.
Press
to confirm your selection.
Please note: The language can subsequently be changed
from the “Settings” menu.
2. SET THE TIME
After selecting the language, you will need to set the
current time: The two digits for the hour will flash on
the display.
Turn the adjustment knob to set the correct hour and
press
: The two digits for the minutes will flash on
the display.
Turn the adjustment knob to set the minutes and press
to confirm.
Please note: You may need to set the time again following
lengthy power outages.
USING THE APPLIANCE FOR THE FIRST TIME
3. SET THE POWER CONSUMPTION
The oven is programmed to consume a level of
electrical power that is compatible with a domestic
network that has a rating of more than 3 kW: If your
household uses a lower power, you will need to
decrease this value.
Turn the selection knob until “SETTINGS” is shown on
the display, then press
to confirm.
Turn the adjustment knob to select the “Power” menu
item and press
to confirm.
Turn the adjustment knob to select “Low” and press
to confirm.
LOW
4. HEAT THE OVEN
A new oven may release odours that have been left
behind during manufacturing: This is completely
normal.
Before starting to cook food, we therefore
recommend heating the oven with it empty in order
to remove any possible odours.
Remove any protective cardboard or transparent
film from the oven and remove any accessories from
inside it.
Heat the oven to 200 °C for around one hour, ideally
using a function with air circulation (e.g. “Forced Air”
or “Convection Bake”).
Follow the instructions for setting the function
correctly.
Please note: It is advisable to air the room after using the
appliance for the rst time.
SLOW
SLOW COOKING
For cooking meat and fish gently
while keeping them tender and succulent. We
recommend searing roasting joints in a pan first
to brown the meat and help seal in its natural
juices. Cooking times range from two hours for
fish weighing 300 g to four or five hours for fish
weighing 3 kg,
and from four hours for joints of meat weighing
1kgto six or seven hours for joints of meat
weighing3kg.
5
EN
DAILY USE
1. SELECT A FUNCTION
Turn the selection knob to switch on the oven and
show the function you require on the display:
Thedisplay will show the icon for the function and its
basic settings.
CONVE
To select an item from the menu (the display will
show the first available item), turn the adjustment
knob until the item you require is shown.
TURBO
Press to confirm your selection: The display will
show the basic settings.
2. SET THE FUNCTION
After having selected the function you require, you
can change its settings.
The display will show the settings that can be
changed in sequence.
TEMPERATURE/GRILL LEVEL
When the value flashes on the display,
turn the adjustment knob to change it, then press
to confirm and continue to alter the settings that
follow (if possible).
Please note: Once the function has been activated, the
temperature can be changed using the adjustment knob.
DURATION
When the icon flashes on the display,
use the adjustment knob to set the cooking time you
require, then press
to confirm.
You do not have to set the cooking time if you want to
manage cooking manually: Press
to confirm and
start the function.
In this case, you cannot set the end cooking time by
programming a delayed start.
Please note: You can adjust the cooking time that has been
set during cooking by pressing : use the adjustment
knob to amend it and then press to conrm.
SET THE COOKING END TIME
DELAYED START
In many functions, once you have set a cooking time
you can delay starting the function by programming
its end time.
The display shows the current end time that is set and
the
icon flashes.
Turn the adjustment knob to set the time you want
cooking to end, then press
to confirm and start
the function.
Place the food in the oven and close the door:
Thefunction will start automatically after the period
of time that has been calculated in order for cooking
to finish at the time you have set.
Notes: Programming a delayed cooking start time will
disable the oven preheating phase: The oven will reach the
temperature your require gradually, meaning that cooking
times will be slightly longer than those listed in the cooking
table.
During the waiting time, you can use the adjustment knob to
amend the programmed end time or press
to change
the settings.
3. ACTIVATE THE FUNCTION
Once you have applied the settings you require, press
to confirm the time that cooking will end and
activate the function.
Please note: Once cooking has started, the display will
recommend the most suitable level for each function.
You can turn the selection knob to to pause the
function that has been activated at any time.
4. PREHEATING
Some functions have an oven preheating phase:
Oncethe function has started, the display indicates
that the preheating phase has been activated.
PRE
6
Once this phase has finished, an audible signal will
sound and the display will indicate that the oven has
reached the set temperature:
At this point, open the door, place the food in the
oven, close the door and start cooking.
Please note: Placing the food in the oven before
preheating has finished may have an adverse effect on
the final cooking result.
Opening the door during the preheating phase will
stop pause it.
The cooking time does not include a preheating phase.
You can always change the temperature you want the
oven to reach using the adjustment knob.
5. END OF COOKING
An audible signal will sound and the display will
indicate that cooking is complete.
Press to continue cooking in manual mode
(without a programmed cooking time) or turn the
adjustment knob to extend the cooking time by
setting a new duration.
In both cases, the temperature or the grill level
settings will be retained.
BROWNING
Some functions of the oven enable you to brown
the surface of the food by activating the grill once
cooking is complete
.
When the display shows the relevant message, if
required press
to start a five-minute browning
cycle.
You can stop the function at any time by turning the
selection knob to
to switch the oven off.
. TIMER
When the oven is switched off, the display can be
used as a timer. To activate this function, make sure
that the oven is switched off and turn the adjustment
knob: The
icon will flash on the display.
Turn the adjustment knob to set the length of time
you require and then press
again to activate the
timer.
An audible signal will sound and the display will
indicate once the timer has finished counting down
the selected time.
Please note: The timer does not activate any of the cooking
cycles.
Use the adjustment knob to change the time set on the
timer; press to switch the timer o at any time.
Once the timer has been activated, you can also
select and activate a function.
Turn the selection knob to switch on the oven and
then select the function your require.
Once the function has started, the timer will continue
to count down independently without interfering
with the function itself.
CONVE
To switch off the timer, turn the selection knob to
to stop the function that is currently active and then
press
.
. KEY LOCK
To lock the keypad, press and hold and at
the same time for at least five seconds.
Do this again to unlock the keypad.
Please note: This function can also be activated during
cooking. For safety reasons, the oven can be switched o at
any time by turning the selection knob to .
7
EN
. DIAMOND CLEAN
Before activating this function, pour 200ml of drinking
water on to the bottom of the oven and shut the door.
Turn the selection knob to select the “DIAMOND
CLEAN” function and press
to confirm.
Press to set the end time of the cleaning cycle or
to activate the function.
A countdown will indicate the status of the cycle in
progress.
To prevent steam from coming out and thus
jeopardizing the final results, it is recommended not
to open the door during the cleaning cycle.
Once finished, wait for the oven to cool down and
then finish cleaning by drying the surfaces with a
sponge or a soft cloth.
Please note: like with the other manual functions, it is also
possible to set the end time for the self-cleaning cycle.
8
COOKING TABLE
RECIPE FUNCTION PREHEAT.
TEMPERATURE
(°C)
COOK TIME
(Min.)
LEVEL
AND
ACCESSORIES
Leavened cakes
PASTR
- 160-180 30-90
2/3
Yes 160-180 30-90
4
1
Filled cake
(cheesecake, strudel, fruit pie)
PASTR
- 160–200 30 - 85
3
Yes 160–200 35-90
4
1
Biscuits/tartlets
PASTR
- 170 – 180 15 - 45
3
Yes 160 -170 20-45
4
1
Yes 160 -170 20-45 ***
5
3
1
Choux buns
Yes 180-200 30-40
3
Yes 180-190 35-45
4
1
Yes 180-190 35-45 ***
5
3
1
Meringues
Yes 90 110 -150
3
Yes 90 130 - 150
4
1
Yes 90 140-160 ***
5
3 1
Pizza (Thin, thick, focaccia)
PIZZA
- 220 - 250 20-40
2
Yes 220 - 240 20-40
4
1
Yes 220 - 240 25-50 ***
5
3
1
Bread loaf 1 kg
BREAD
- 180 - 220 50 - 70
2
Rolls
BREAD
- 180 - 220 30 - 50
2
Bread Yes 180-200 30 - 60
4
1
Frozen pizza
PIZZA
Yes 250 10 - 15
3
Yes 250 10 - 20
4
1
Salty cakes
(vegetable pie, quiche)
Yes 180-190 40-55
2 / 3
Yes 180-190 45 - 60
4
1
Yes 180-190 45-70 ***
5
3 1
Vols-au-vents/pu pastry
crackers
Yes 190-200 20-30
3
Yes 180-190 20-40
4
1
Yes 180-190 20-40 ***
5
3 1
Lasagne/soué
CASSE
- 190-200 40 - 65
3
Baked pasta/cannelloni
CASSE
- 190-200 25 - 45
3
9
EN
* Turn food halfway through cooking.
** Turn food two thirds of the way through cooking
(if necessary).
*** Estimated length of time: dishes can be removed
from the oven at different times depending on
personal preference.
WWW
Download the Use and Care Guide from
docs.hotpoint.eu for the table of tested recipes,
compiled for the certification authorities in
accordance with the standard IEC 60350-1
MANUAL
FUNCTIONS
Conventional Grill Turbo Grill Forced Air Convection Bake Eco Forced Air
SPECIAL
FUNCTIONS
MEAT POULT CASSE
BREAD PIZZA
PASTR
Meat Poultry Casserole Bread Pizza Pastry
ACCESSORIES
Wire shelf
Baking tray or cake tin on
the wire shelf
Drip tray / Dessert tray /
Baking tray on wire shelf
Drip tray
Drip tray with 500 ml of
water
Baking tray
RECIPE FUNCTION PREHEAT.
TEMPERATURE
(°C)
COOK TIME
(Min.)
LEVEL
AND
ACCESSORIES
Lamb/veal/beef/pork
1 kg
MEAT
- 190-200 60 - 90
3
Chicken/rabbit/duck 1 kg
POULT
- 200-230 50 - 80
3
Turkey/goose 3 kg
POULT
- 190-200 90 - 150
2
Baked sh/en papillote
(llet,whole)
Yes 180-200 40-60
3
Stued vegetables
(tomatoes, courgettes, aubergines)
Yes 180-200 50-60
2
Toasted bread - 3 (High) 3-6
5
Fish llets/slices - 2 (Medium) 20-30 *
4
3
Sausages/kebabs/spare ribs/
hamburgers
-
2 - 3 (Medium -
High)
15 - 30 *
5
4
Roast chicken 1-1.3 kg - 2 (Medium) 55-70 **
2
1
Roast beef rare 1 kg - 2 (Medium) 35-50 **
3
Leg of lamb/knuckle - 2 (Medium) 60-90 **
3
Roast potatoes - 2 (Medium) 35-55 **
3
Vegetable gratin - 3 (High) 10-25
3
Lasagne and meat Yes 200 50-100 ***
4
1
Meat and potatoes Yes 200 45-100 ***
4
1
Fish and vegetables Yes 180 30-50 ***
4
1
Complete meal: Fruit tart (level
5)/lasagne (level 3)/meat (level 1)
Yes 190 40-120 ***
5
3 1
Stued roasting joints - 200 80-120 ***
3
Cuts of meat (rabbit, chicken,
lamb)
- 200 50-100 ***
3
10
MAINTENANCE
AND CLEANING
WWW
REPLACING THE LAMP
1. Disconnect the oven from the power supply.
2. Unscrew the cover from the light, replace the bulb
and screw the cover back on the light.
3. Reconnect the oven to the power supply.
Please note: Only use 25-40 W/230 V type E-14, T300 °C
incandescent bulbs, or 20-40 W/230 V type G9, T300 °C
halogen bulbs. The bulb used in the product is specically
designed for domestic appliances and is not suitable for
general room lighting within the home (EC Regulation
244/2009). Light bulbs are available from our After-sales
Service.
- If using halogen bulbs, do not handle them with your bare
hands as your ngerprints could cause damage. Do not use
the oven until the light cover has been retted.
EXTERIOR SURFACES
Clean the surfaces with a damp microfibre cloth.
If they are very dirty, add a few drops of pH-neutral
detergent. Finish off with a dry cloth.
Do not use corrosive or abrasive detergents. If any of
these products inadvertently comes into contact with
the surfaces of the appliance, clean immediately with
a damp microfibre cloth.
INTERIOR SURFACES
After every use, leave the oven to cool and then
clean it, preferably while it is still warm, to remove
any deposits or stains caused by food residues. To
dry any condensation that has formed as a result of
cooking foods with a high water content, leave the
oven to cool completely and then wipe it with a cloth
or sponge.
Clean the glass in the door with a suitable liquid
detergent.
The oven door can be removed to facilitate cleaning
WWW
.
The top heating element of the grill can be lowered
to clean the upper panel of the oven
WWW
.
ACCESSORIES
Soak the accessories in a washing-up liquid solution
after use, handling them with oven gloves if they
are still hot. Food residues can be removed using a
washing-up brush or a sponge.
Make sure that the oven has
cooled down before carrying
out any maintenance or
cleaning.
Do not use steam cleaners.
Do not use wire wool, abrasive
scourers or abrasive/corrosive
cleaning agents, as these could
damage the surfaces of the
appliance.
Wear protective gloves.
The oven must be disconnected
from the mains before carrying
out any kind of maintenance
work.
Download the Use and Care Guide from
docs.hotpoint.eu for more information
11
EN
REMOVING AND REFITTING THE DOOR
1. To remove the door, open it fully and lower the
catches until they are in the unlock position.
b
a
2. Close the door as much as you can.
Take a firm hold of the door with both hands – do not
hold it by the handle.
Simply remove the door by continuing to close it
while pulling it upwards at the same time until it is
released from its seating. Put the door to one side,
resting it on a soft surface.
a
b
~15°
3. Refit the door by moving it towards the oven,
aligning the hooks of the hinges with their seating
and securing the upper part onto its seating.
4. Lower the door and then open it fully.
Lower the catches into their original position:
Makesure that you lower them down completely.
b
a
Apply gentle pressure to check that the catches are in
the correct position.
“CLICK”
5. Try closing the door and check to make sure that it
lines up with the control panel. If it does not, repeat
the steps above: The door could become damaged if
it does not work properly.
TROUBLESHOOTING
WWW
Problem Possible cause Solution
The oven is not working. Power cut.
Disconnection from the
mains.
Check for the presence of mains electrical
power and whether the oven is connected
to the electricity supply.
Turn off the oven and restart it to see if the
fault persists.
The display shows the letter “F
followed by a number or letter.
Software problem. Contact you nearest Client After-sales
Service Centre and state the number
following the letter “F”.
Download the Use and Care Guide from
docs.hotpoint.eu for more information
12
HOW TO READ THE COOKING TABLE
The table lists the best function, accessories and
level to use to cook various different types of food.
Cooking times start from the moment food is placed
in the oven, excluding preheating (where required).
Cooking temperatures and times are approximate
and depend on the amount of food and the type
of accessory used. Use the lowest recommended
settings to begin with and, if the food is not cooked
enough, then switch to higher settings. Use the
accessories supplied and preferably dark-coloured
metal cake tins and baking plates. You can also use
Pyrex or stoneware pans and accessories, but bear in
mind that cooking times will be slightly longer.
COOKING DIFFERENT FOODS AT THE SAME TIME
Using the “Forced Air” function, you can cook
different foods which require the same cooking
temperature at the same time (for example: fish and
vegetables), using different shelves. Remove the food
which requires a shorter cooking time and leave the
food which requires a longer cooking time in the
oven.
USEFUL TIPS
WWW
Download the Use and Care Guide from
docs.hotpoint.eu for more information
PRODUCT FICHE
WWW
The product fiche with energy data of this
appliance can be downloaded from our website
docs.hotpoint.eu
HOW TO OBTAIN THE USE AND CARE GUIDE
>
WWW
Download the Use and Care
Guide from our website docs.hotpoint.eu
(youcanuse this QR code), specifying the
product's commercial code.
> Alternatively, contact our Client After-sales Service
400010858937
Printed in Italy
CONTACTING OUR AFTERSALES SERVICE
You can find our contact details in the warranty
manual. When contacting our Client After-sales
Service, please state the
codes provided on your
product's identification
plate.
Model: xxxXXXXxx
X
X
X
X
X
XX
X
X
X
X
X
XX
X
XX
X
X
X
XX
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
X
X
X
X
XX
X
X
X
X
X
XXXXXX XXXXXX XXXXX XXXXXXX
001
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Hotpoint FI6 864 SH IX HA Setup and user guide

Type
Setup and user guide
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI