Kenmore AWM 8000/1 User guide

Brand: Kenmore

Model: AWM 8000/1

Category: Washing machines

Type: User guide

The Kenmore AWM 8000/1 is a washing machine with an extra-large capacity drum and wide door, making it suitable for large loads and easy to load and unload. It features a child lock to prevent children from turning the machine on or changing the settings, ensuring safety during operation. Additionally, the machine has a "Door Locked" warning light that indicates when the door is locked, preventing accidental opening during wash cycles.

CONTENTS

BEFORE USING THE WASHING MACHINE

FIRST WASH CYCLE

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

DESCRIPTION OF THE WASHING MACHINE

CHILD LOCK

DETERGENTS AND ADDITIVES

DRAINING RESIDUAL WATER

REMOVING THE FILTER

CARE AND MAINTENANCE

TROUBLESHOOTING GUIDE

AFTER SALES SERVICE

TRANSPORT AND HANDLING

INSTALLATION

ELECTRICAL CONNECTION

3gb15103.fm Page 4 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

BEFORE USING THE WASHING MACHINE

Remove the packaging and check

•

After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use the

washing machine. Contact After-Sales Service or

your local dealer.

•

Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children,

since it is a possible source of danger.

2.Remove the transit bolts

•

The appliance is fitted with transit bolts to

prevent internal damage during transport.

Before using the washing machine you must

remove the transit bolts

(see “Installation/

Remove the transit bolts”).

3.Install the washing machine

•

Install the appliance on a solid and level floor

surface. In the case of a yielding sub-floor, the

appliance should be installed in the corner of a

room.

•

Adjust the feet to ensure that the machine is

stable and level on the floor (see “Installation/

Adjust the feet”).

4.Water inlet

•

Connect the water supply inlet hose in

accordance with the regulations of your local

water company (see "Installation/Connect the

water inlet hose").

•

Water supply: Cold water only

•

Tap: 3/4” threaded hose connection

•

Pressure: 100-1000 kPa (1-10 bar).

5.Drain hose

•

Connect the drain hose to the ventilated siphon

or hook it over the edge of a sink by means of the

“U” bend (see “Installation/Connect the water

drain hose”).

6.Electrical connections

•

Electrical connections must be carried out by a

qualified electrician in compliance with the

manufacturer's instructions and local safety

regulations.

•

Voltage information, power consumption and

electrical fusing data are supplied on the front

panel behind the door frame.

•

The appliance must be connected to the mains

exclusively by means of a socket with an earth

connection in accordance with established

regulations. The appliance must be earthed by

law. The manufacturer declines all liability for

possible damage to property or injury to persons

or pets deriving from failure to observe the a/m

directions.

•

Do not use extension leads or multi sockets.

•

Before any maintenance on the washing machine

disconnect the power plug or switch off the

power supply.

•

Access to the mains plug or to disconnection

from mains supply via a double-pole switch must

be ensured at all times following the installation.

•

Do not operate the washing machine if it has

been damaged during transport. Inform the

After-Sales Service.

•

Mains cable replacement is only to be carried out

by After-Sales Service.

•

The washing machine must only be used in the

household for the prescribed uses.

3gb15103.fm Page 5 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

FIRST WASH CYCLE

PRECAUTIONS AND GENERAL

RECOMMENDATIONS

1.Packaging

•

The packaging is 100% recyclable and is marked

with the recycling symbol . Adhere to

current local regulations when disposing of

packaging material.

2.Disposing of packaging and old

appliances

•

The washing machine is built from reusable

materials. The washing machine must be

disposed of in compliance with current local

waste disposal regulations.

•

Before scrapping, pull out the mains plug and cut

off the power cable so that the washing machine

becomes unusable.

•

The detergent residues should also be removed

from the detergent dispenser, the drum, the

water drain hose and pump before the washing

machine is scrapped. The detergent residues

might otherwise get into the groundwater during

the disposal process and contaminate it.

3.Child safety

•

The appliance must not be operated by children.

Children must not be allowed to play with the

washing machine, to climb into the drum, to

handle the pedestal drawer or its content.

4.Safety Instructions

•

No other appliances are to be placed on the

washing machine worktop (e.g. tumble dryer,

water heater etc.).

5.General recommendations

•

Never leave the appliance switched on

unnecessarily. Turn off the tap.

•

Before any cleaning and maintenance pull out the

mains plug or switch off the power supply.

•

To clean the outside of the washing machine, use

a neutral detergent and a damp cloth.

•

Do not use abrasive detergents.

•

Never force the door open.

•

If necessary, the power cable may be replaced

with an identical one obtained from our After-

Sales Service. The power cable must only be

replaced by a qualified technician.

6.EC Declaration of Conformity

•

This washing machine has been designed,

constructed and distributed in compliance with

EC safety requirements:

73/23/EEC Low Voltage Directive

89/336/EEC EMC Directive

93/68/EEC CE Marking Directive

We recommend that the first wash cycle be made without laundry.

This will remove any residual water used by the manufacturer in testing your washing machine.

Turn on the tap.

Close the appliance door.

Pour a small amount of detergent (about 30 ml) into the detergent dispenser .

Select a short wash programme (see programme chart).

Press the

“Start/Pause”

button.

3gb15103.fm Page 6 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

DESCRIPTION OF THE WASHING MACHINE

Worktop

Control panel

Detergent dispenser

After-Sales Service sticker (on

the front panel behind the door

frame)

Door

Door handle

•

To open the door pull the handle

•

Close the door by pushing it

firmly (the lock will click into

place)

Adjustable feet

Filter behind the cover

3gb15103.fm Page 7 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

CHILD LOCK

We are pleased that you have chosen our washing machine with the extra-large capacity drum and wide

door. They may also appeal to your young children, so we have taken special measures to protect

youngsters who decide to play in or around the machine. These measures are intended to help busy

parents, but remember that children should never play with the machine, whether it is running or not.

Door Opening

The door has NO special interlock, so it can be opened from inside without much force by a small child

if the machine is not in operation. If the machine is switched on, the door is locked so that hot water or

laundry cannot be thrown out.

Door lock

After the programme has started, the door is locked and approx. 0.5 l of water is rinsed into the drum.

The door is then unlocked for a few seconds and subsequently locked until the end of the programme.

The “Door Locked” warning light goes on if the door is locked. If the door has to be opened during a

programme, press the

“Start/Pause”

button. The “Door Locked” warning light goes out and the

“Start/Pause”

indicator flashes. The door can now be opened. The machine can be started again by

shutting the door and pressing the

“Start/Pause”

button.

The door can never be opened in certain stages of the wash cycle, e.g. when the water is very hot or

could run out. In these cases the door remains locked and the “Door Locked” warning light goes on again

after the

“Start/Pause”

button has been pressed. If you still have an urgent need to open the machine,

do not pull the plug out but press the “Reset” button. This drains all the water out, and the door can then

be opened.

Child lock Button

You can prevent children turning the machine on by disabling the controls. To do this, simply PRESS and

HOLD the “Child Lock” button for 5 seconds. An indicator light will come on and all controls will be

disabled. Only the programme selector knob can be turned, so that the machine can be stopped

immediately in an emergency. To do this, turn the knob to the “ ” position. If the machine was already

running a programme when the “Child Lock” was set, the programme will continue normally to the end,

but it will be impossible to make any changes to the programme. If the machine is switched off after

pressing the “Child Lock” button, it will be impossible to start another programme. If the programme

selector knob is then turned to a programme position, the “Child Lock” indicator light flashes briefly

indicating that it is activated. To switch off the lock at any time, PRESS the “Child Lock” button AGAIN

and HOLD for 5 seconds.

Child lock screws (inside the door)

Activating the child lock

Open the door.

Using the insert from the detergent dispenser, turn the plastic screw underneath the handle anti-

clockwise by about 180°. The screw now protrudes somewhat and the door cannot be closed.

Deactivating the child lock

Use the detergent dispenser insert to return the screw to its original position. The door can now be

shut.

3gb15103.fm Page 8 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

DETERGENTS AND ADDITIVES

Pouring in detergents and additives

Pull out the detergent dispenser to its full extent.

Pour in detergent:

Chamber

•

Detergent for the pre-wash

Chamber

•

Detergent for the main wash

•

Stain remover

•

Water softener (water hardness 4)

When using liquid detergent, put the divider insert in the

front slot and in the rear slot when using powder

detergent. (See marking).

Chamber

•

Fabric Softener

•

Liquid starch

Only add fabric softeners and conditioners up to the “Max” mark.

Chamber

•

Liquid chlorine bleach

Only add the liquid chlorine bleach up to the “Max” mark.

Only use this chamber if the “Bleach” column is shown on the

enclosed programme chart.

Slide the detergent dispenser in until it clicks shut.

powder detergent-

use rear slot

liquid detergent-

use front slot

Divider

insert

Divider

insert

3gb15103.fm Page 9 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

Notes:

•

Keep detergents and additives in a dry place and out of reach of children.

•

If you use descaling agents, dyes or bleaches, make sure they are suitable for washing machine use.

Descaler could contain components that can attack parts of your washing machine.

•

Do not use solvents (turpentine, benzine, etc.)

Do not machine wash fabrics that have been treated with solvents or flammable liquids.

•

You can use liquid detergent in the "Prewash" phase for programmes with this option. In this case put

only powder detergents in the compartment for the main wash .

•

When using concentrated fabric softeners, dilute with water in the detergent dispenser up to "MAX"

level mark.

•

To prevent dispensing problems when using highly concentrated powder and liquid detergents, use the

special detergent ball or bag supplied with the detergent and place it directly inside the drum.

If you use gel-type detergent, please use the powder detergent insert setting.

•

For Start Delay, only use powder detergent, please. Powder detergent remains in the detergent

dispenser until the programme starts, but liquid detergents can run out of the detergent dispenser.

•

If you use powder starch, proceed as follows:

Wash your laundry using the desired wash programme.

Next mix the starch with water in a cup.

Set the “Rinse and Spin” programme, reduce the speed to ca. 800 rpm and start the programme.

Pull the detergent dispenser out until you can see about 3 cm of the chamber.

While the water is running into the detergent dispenser, pour the starch solution into the

chamber.

If there are starch residues in the detergent dispenser after the end of the programme, clean it if

necessary (see "Care and Maintenance").

Observe also the starch manufacturer's information.

3gb15103.fm Page 10 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

DRAINING RESIDUAL WATER

Draining Residual Water

Residual water should be removed:

•

before moving a washing machine (relocation),

•

when installing in areas prone to frost and

•

before removing the filter.

Before emptying the residual water, switch the appliance off

and unplug it from the mains socket Make sure that the water

has cooled before draining

Turn the slot through 180°, so that the dot points to the open

lock. To do this, use the insert from the detergent dispenser

or a coin. The cover bends down to the floor.

Remove the hose, place a low container underneath and pull

the cap from the hose.

Drain the residual water until no more flows out. Then close

the residual water emptying hose.

Put the hose in the cover, fold the cover up and close the cover

using the detergent dispenser insert or a coin. The dot points

to the closed lock.

Pour about 1 l of water into the detergent dispenser to

reactivate the ecosystem. You must also plug the mains plug

back into the socket-outlet.

Now you can fill the washing machine and run the desired

programme.

2/5

3gb15103.fm Page 11 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

REMOVING THE FILTER

Removing the filter

The filter must be taken out if:

•

if the washing machine does not drain properly,

•

if small items, e. g. buttons and coins rattle in the pump and

•

2 to 3 times a year for inspection.

You must remove the residual water before taking out the filter.

Carry out the steps in the “Draining Residual Water” section, but

only up to point 4. Then follow the points given below.

Open the filter but do not withdraw it completely. Slowly turn

the handle anticlockwise until the water drains out. Make sure

that the water has cooled before letting it drain.

Wait until all the water has drained out.

Now unscrew the filter completely and extract it.

Clean the filter and the filter chamber.

Check that the pump impeller can still rotate.

Insert the filter with the guide pin upwards and screw it in

clockwise.

Lay the hose in the cover, fold the cover up and close it using

the detergent dispenser insert or a coin. The dot points to the

closed lock.

Pour about 1 l of water into the detergent dispenser to

reactivate the Eco System. You must also put the plug back

into the socket.

You can now load the washing machine and start the desired

programme.

3gb15103.fm Page 12 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

CARE AND MAINTENANCE

Appliance exterior and control panel

•

Clean using normal household cleaner (do not

use abrasive products or solvents).

•

Dry with a soft cloth.

Door seal

•

Clean occasionally with a damp cloth.

•

Check the seal folds for foreign bodies

periodically.

Filter

•

Check and clean the filter regularly, at least two

or three times a year (see “Removing the Filter”).

Detergent dispenser

Press the release lever in the prewash compartment down and

pull out the dispenser.

Remove the inserts from the detergent dispenser.

Clean all parts under running water.

Replace the separate parts in the detergent dispenser and slide

the dispenser back into the opening.

Periodically check and clean the mesh filters in the

water connection.

Turn off the tap.

Unscrew the water inlet hose from the tap.

Clean the internal filter.

Screw the supply hose back onto the tap.

Unscrew the supply hose from the washing machine.

Clean the mesh filter in the washing machine.

Screw the supply hose back on to the machine.

Turn on the tap and ensure that the connections are water-

tight.

3gb15103.fm Page 13 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

TROUBLESHOOTING GUIDE

This washing machine is equipped with automatic

safety functions which detect and diagnose faults at

an early stage and react appropriately.

Often, however, the faults detected are small

enough to be solved in a matter of minutes.

For example:

The appliance will not start; no lamp

lights up.

Check whether:

•

the appliance is plugged in;

•

the wall socket is functioning correctly

(use a table lamp or similar to test);

•

a programme is selected correctly.

The appliance will not start, but the

“Start/Pause” lamp is flashing.

Check whether:

•

the appliance door is properly closed (child lock);

•

the programme has been changed;

•

the water tap is turned on. If not, turn the tap on

and press the

“Start/Pause”

button.

The appliance stops during the programme.

Check whether:

•

the

“Rinse Hold”

lamp is on. Terminate this

option by pressing the button again;

•

another programme has been selected.

Reselect the desired programme and press the

“Start/Pause”

button;

•“Start/Pause”

lamp goes on. Press

“Start/

Pause”

button;

•

The appliance safety system has been activated.

See fault description table.

Detergent and additives incorrectly

washed in.

Check whether:

•

the detergent dispenser inserts are incorrectly

located (see “Care and Maintenance”);

•

enough water is being supplied. The mesh filters

in the water connection could be blocked (see

“Care and Maintenance”).

The appliance vibrates during the spin cycle.

Check whether:

•

the appliance is levelled and solidly installed on all

four feet (see “Installation”);

•

the transit bolts have been removed. Before

using the washing machine you must remove the

transit bolts (see “Installation”).

Final spin results are poor:

The appliance has an imbalance detection and

correction system. If individual heavy articles are

loaded (bathmat, bathrobe, etc.) this system may

reduce the spin speed automatically to protect the

appliance or even interrupt the spin cycle

altogether, if the imbalance is too great even after

several spin starts.

•

If the laundry is still too wet at the end of the

cycle, add other articles of laundry and repeat the

spin cycle.

•

Excessive foam formation may prevent spinning.

Ensure correct amount of detergent is used.

•

Check whether the spin speed has been reduced

to 0.

No water or insufficient water pressure

for appliances with safety hose:

•

the appliance has a safety hose and the safety

valve has opened (red indicator in the safety valve

inspection window).

In this case replace it with a new safety hose.

The programme time given on the time

remaining display “jumps” suddenly up or

down by several minutes, or the

programme duration shown at the start

increases/decreases by some time.

This is a normal adaptation action by the washing

machine to factors that can affect the duration of

the wash programme, e.g.

•

excessive foaming;

•

load imbalance from individual, heavy items of

laundry;

•

longer heating time from correspondingly cold

water supply.

Because of such influences, the time remaining in

the programme is recalculated and updated if

necessary. In addition, the washing machine

determines the amount of the load during the filling

phase and adjusts the initially indicated programme

duration appropriately if necessary.

3gb15103.fm Page 14 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

What should I do when the automatic safety system detects a malfunction?

The programme is interrupted and various indicators (if available) point to the source of the fault.

Fault description table

a.Water inlet fault (no water or insufficient

water pressure)

The “Water tap closed” indicator is on and the

digital display shows “FH” Switch off the

appliance by turning the programme selector to

the “ ” position and unplug it.

Check whether:

•

the water tap is open and the water supply

pressure is sufficient;

•

the water inlet hose is kinked;

•

the mesh filter between the tap and the hose is

clean (see “Care and Maintenance” / “Mesh filter

in water connection”);

•

the water supply hose is frozen up.

Connect the appliance to the electrical supply.

Reselect the desired programme and press the

“Start/Pause”

button again to continue with

the programme (do not add detergent for this

programme)

b.Draining fault

The digital display shows “FP”. Switch off the

appliance by turning the programme selector to

the “ ” position and unplug it.

Check whether:

•

the drain hose is kinked (see “Installation”);

IMPORTANT

: before draining, allow the wash

water to cool down.

•

the drain hose is frozen.

Connect the appliance to the electrical supply.

•

The pump/filter is blocked (see “Removing the

Filter” / “Draining Residual Water”).

IMPORTANT:

Make sure that the washing

water has cooled before draining.

Reselect the desired programme and press the

“Start/Pause”

button again to continue with

the programme (do not add detergent for this

programme). If the fault re-occurs, contact After

Sales Service (See “After Sales Service”).

c. Electrical module fault

The digital display shows “F4” to “F21”.

•

Set the programme selector to the “ ”

position, select the desired programme and

press the

“Start/Pause”

button again. The

programme will continue.

•

If the fault re-occurs, contact After Sales

Service (See “After Sales Service”).

d.Water Stop fault

An audible tone sounds. The light of the Water

Stop indicator goes on. The digital display shows

“FA” and the pump is running.

The “Water Stop fault” may have been

triggered by:

•

too much foam.

•

a leak in the appliance, water running into the

water tank.

Switch off the appliance by turning the

programme selector to the “ ” position,

unplug the appliance and turn off the tap.

Inform After-Sales Service and describe the fault

(see “After-Sales Service”).

If the “Start/Pause” button has not been pressed

but water is still running into the machine, shut

the water intake and also inform After-Sales

Service (see “After-Sales Service”).

Small lamp lights up Digital display Fault description

“Water tap closed” “FH” “Water inlet fault”

- “FP” “Draining fault”

- from “F4” to “F21” “Electrical components fault”

“Water Stop” “FA” “Water Stop fault”

3gb15103.fm Page 15 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

AFTER SALES SERVICE

Before contacting After-Sales Service:

Try to remedy the problem yourself (see

“Troubleshooting Guide”).

Restart the programme to check whether the

problem has solved itself.

If the machine continues to function incorrectly,

call After-Sales Service.

Specify:

•

The nature of the problem.

•

Appliance and model number.

•

The service code (number after the word

SERVICE).

The After-Sales Service sticker is on the

front panel behind the door frame.

•

Your full address.

•

Your telephone number and area code. After-

Sales Service phone numbers and addresses are

given on the guarantee card or consult the local

dealer.

TRANSPORT AND HANDLING

Pull out the power plug.

Turn off the tap.

Remove the water supply and drain hose from the service connection.

Empty the water supply hose and the water drain hose completely.

Always fit the transit bolts (see “Installation/Remove transit bolts”).

3gb15103.fm Page 16 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

INSTALLATION

Remove the transit bolts

Slacken the four bolts with the spanner supplied. In

addition, open the plastic loop wrapped round the

power cable.

Do not cut the loop.

Unscrew the bolt by hand.

Grip the bolt and remove it through the large aperture.

Seal the resulting holes using the plastic caps supplied.

To do this, insert the caps in the wide part of the hole in

the direction of the arrow and push them into the

narrow groove until they click into place.

Keep the transit bolts for future use.

•

Whenever the appliance is transported, the transit bolts

must be refitted:

Raise the plastic covers with a screwdriver, slide them in

the opposite direction of the arrow and remove.

Insert the transit bolts in the reverse order.

3gb15103.fm Page 17 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

Adjust the feet

Small unevennesses in the floor can be compensated for by

screwing the four appliance feet up or down (never use

pieces of wood, cardboard or similar material):

The washing machine must be installed horizontally in

width and depth. Use a spirit level.

Loosen the locknut clockwise using the wrench

provided.

Adjust the height of the foot by hand.

Tighten the locknut anti-clockwise to the washing

machine.

If the appliance is to be installed on a wooden floor,

distribute the weight by placing it on a 70 x 70 cm sheet of

plywood at least 3 cm in thickness.

Screw the plywood sheet to the floor.

3gb15103.fm Page 18 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

Connect the water supply hose

Carefully screw the hose connection onto the tap,

preferably by hand.

Make sure there are no kinks in the hose.

Check water-tightness of tap and appliance connections by

turning the tap completely on.

The appliance

must not be

connected to the mixing tap of a

non-pressurized water heater.

The appliance can be connected without a non-return valve.

Check the supply hose regularly for brittleness and cracks and

replace if necessary using a new hose of the same type

(available from After-Sales Service or specialist dealer).

If the flexible hose is damaged, unplug the appliance from the

mains immediately.

Water supply hose “A”

If the hose is too short, replace it with a suitable length of

pressure resistant hose (minimum 1000 kPa - EN 50084

approved type).

Mount the new hose professionally on the washing machine

and the tap.

Water supply hose “B”

If the hose is too short, replace it with a longer length of

“Water Stop” hose (available from After-Sales Service or

specialist dealer).

Mount the new hose professionally on the washing machine

and the tap.

Note: The inlet hose and the plastic enclosure at the water

connection contain electrical components.

For this reason,

do not cut the hose and do not immerse the plastic

enclosure in water.

Connect the water drain hose

Connect the drain hose to the ventilated siphon or hook it over the edge of a sink with the “U” bend.

Make sure there are no kinks in the hose.

Secure the hose so that it cannot fall down while the appliance is running.

Small wash-hand basins are unsuitable.

If you need to add an extension, use a hose of the same type. Secure the connections with clips.

Max. drain hose length: 2.50 m

Max. drain height: 1.25 m

Min. drain height: 0.70 m

3gb15103.fm Page 19 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

ELECTRICAL CONNECTION

For Great Britain only

Warning - this appliance must be earthed

Fuse replacement

If the mains lead of this appliance is fitted with a

BS 1363A 13amp fused plug, to change a fuse in this type

of plug use an A.S.T.A. approved fuse to BS 1362 type and

proceed as follows:

Remove the fuse cover (

) and fuse (

Fit replacement 13A fuse into fuse cover.

Refit both into plug.

Important:

The fuse cover must be refitted when changing a fuse and

if the fuse cover is lost the plug must not be used until a

correct replacement is fitted.

Correct replacement are identified by the colour insert or

the colour embossed in words on the base of the plug.

Replacement fuse covers are available from your local

electrical store.

For the Republic of Ireland only

The information given in respect of Great Britain will

frequently apply, but a third type of plug and socket is also

used, the 2-pin, side earth type.

Socket outlet / plug (valid for both countries)

If the fitted plug is not suitable for your socket outlet,

Please contact Whirlpool Service for further instruction.

Please do not attempt to change plug yourself. This

procedure needs to be carried out by a qualified Whirlpool

technician in compliance with the manufactures

instructions and current standard safety regulations.

3gb15103.fm Page 20 Friday, August 27, 2004 6:52 PM

Black process 45.0° 150.0 LPI

Kenmore AWM 8000/1 User guide

Brand: Kenmore

Model: AWM 8000/1

Category: Washing machines

Type: User guide

Download PDF

report

Kenmore AWM 8000/1 User guide

Kenmore AWM 8000/1 User guide

Related papers

Other documents