KitchenAid KOLP 7105 User guide

Category
Kitchen & houseware accessories
Type
User guide
Instructions for use
Important safety instructions 4
Installation 8
Safeguarding the environment 9
EC Declaration of conformity 9
Troubleshooting Guide 9
After-Sales Service 10
Cleaning 10
Maintenance 11
Instructions for oven use 13
Functions description table 26
Cooking table 28
Table of Tested Recipes 31
Recommended use and tips 32
4
Important safety instructions
YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT
This manual and the appliance itself provide important safety warnings, to be read
and observed at all times.
This is the danger symbol, pertaining to safety, which alerts users to
potential risks to themselves and others. All safety warnings are preceded
by the danger symbol and the following terms:
Indicates a hazardous situation which,
if not avoided, will cause serious injury.
Indicates a hazardous situation which,
if not avoided, could cause serious injury.
All
safety warnings give specific details of the potential
risk present and indicate how to reduce risk of injury,
damage and electric shock resulting from improper use
of the appliance. Carefully observe the following
instructions:
Use protective gloves to perform all unpacking and
installation operations.
The appliance must be disconnected from the power
supply before carrying out any installation work.
Installation and maintenance must be carried out by a
qualified technician, in compliance with the
manufacturer's instructions and local safety regulations.
Do not repair or replace any part of the appliance
unless specifically stated in the user manual.
Power cable replacement must be carried out by
qualified electician. Contact an authorizes service
centre.
Regulations require that the appliance is earthed.
The power cable must be long enough for connecting
the appliance, once fitted in its housing, to the power
supply socket.
WARNING
DANGER
5
For installation to comply with current safety
regulations, an all-pole disconnect switch with
minimum contact gap of 3 mm must be utilized.
Do not use multiple plug adapters if the ovens is fitted
with a plug.
Do not use extension leads.
Do not pull the power supply cable.
The electrical components must not be accessible to
the user after installation.
Do not touch the appliance with any wet part of the
body and do not operate it when barefoot.
This appliance is designed solely for use as a domestic
appliance for cooking food. No other type of use is
permitted (e.g.: heating rooms). The Manufacturer
declines all responsibility for inappropriate use or
incorrect setting of the controls.
The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching
heating elements. Very young (0-3 years) and young
children (3-8 years) shall be kept away unless
continuously supervised.
Children from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack
of experience and knowledge can use this appliance
only if they are supervised or have been given
instructions on safe appliance use and if they
understand the hazards involved. Children shall not
play with the appliance. Cleaning and user
maintenance shall not be made by children without
supervision.
During and after use, do not touch the heating
6
elements or interior surfaces of the appliance - risk of
burns. Do not allow the appliance to come into
contact with cloths or other flammable materials until
all the components have cooled down completely.
At the end of cooking, exercise caution when opening
the appliance door, letting the hot air or steam exit
gradually before accessing the oven. When the
appliance door is shut, hot air is vented from the
aperture above the control panel. Do not obstruct the
vent apertures.
Use oven gloves to remove pans and accessories,
taking care not to touch the heating elements.
Do not place flammable materials in or near the
appliance: a fire may break out if the appliance is
inadvertently switched on.
Do not heat or cook sealed jars or containers in the
appliance. The pressure that builds up inside might
cause the jar to explode, damaging the appliance.
Do not use containers made of synthetic materials.
Overheated oils and fats catch fire easily. Always
remain vigilant when cooking foods rich in fat and oil.
Never leave the appliance unattended during food
drying.
If alcoholic beverages are used when cooking foods
(e.g. rum, cognac, wine), remember that alcohol
evaporates at high temperatures. As a result, there is a
risk that vapours released by the alcohol may catch
fire upon coming into contact with the electrical
heating element.
Never use steam cleaning equipment.
Do not touch the oven during the pyrolysys cycle.
7
Keep children away from the oven during the pyrolysis
cycle. Excess spillage must be removed from the oven
cavity before cleaning cycle (only for ovens with
Pyrolysis function).
Only use the temperature probe recommended for
this oven.
Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass since they can
scratch the surface, which may result in shattering of
the glass.
Ensure that the appliance is switched off before
replacing the lamp to avoid the possibility of electric
shock.
8
After unpacking the oven, make sure that it has not
been damaged during transit and that the oven
door closes properly.
In the event of problems, contact the dealer or
your nearest After-Sales Service. To avoid any
damage, only remove the oven from its
polystyrene foam base at the time of installation.
Preparing the housing unit
Kitchen units in contact with the oven must be
heat resistant (min 90°C).
Carry out all cabinet cutting work before fitting
the oven in the housing and carefully remove all
wood chips and sawdust.
After installation, the bottom of the oven must
no longer be accessible.
For correct appliance operation, do not
obstruct the minimum gap between the
worktop and the upper edge of the oven.
Electrical connection
Make sure the power voltage specified on the
appliance dataplate is the same as the mains
voltage. The dataplate is on the front edge of the
oven (visible when the door is open).
Power cable replacement (type H05 RR-F 3 x
1.5 mm
2
) must be carried out by a qualified
electrician. Contact an authorized service
centre.
The oven is programmed to operate with power
absorption above 2.5 kW (indicated by "HIGH" in the
settings, as shown in the figure below) which is
compatible with a domestic power supply above 3
kW. If the household has a lower power supply, the
setting must be lowered ("LOW" in the settings). The
table below details the recommended electrical
power settings for the various countries.
1. To lower the power absorption setting, select
"SETTINGS" from the main menu using buttons
2. Confirm with button
3. Select "power" on the menu
4. Confirm with button
5. Select "LOW"
6. Press button ; a message appears on the
display confirming your selection.
GENERAL RECOMMENDATIONS
Before use:
Remove cardboard protection pieces,
protective film and adhesive labels from the
oven and the accessories.
Remove the accessories from the oven and heat
it at 200°C for about an hour to eliminate the
smell and fumes from the protective grease and
insulating materials.
During use:
Do not place heavy objects on the door as they
could damage it.
Do not cling to the door or hang anything from
the handle.
Do not cover the inside of the oven with
aluminium foil.
Do not pour water into the inside of a hot oven;
this could damage the enamel coating.
Do not drag pots or pans across the bottom of
the oven as this could damage the enamel
coating.
Make sure that the electrical cables of other
appliances do not touch hot parts of the oven
or become trapped in the door.
Do not expose the oven to atmospheric agents.
Installation
COUNTRY
ELECTRICAL POWER
SETTING
GERMANY HIGH
SPAIN LOW
FINLAND HIGH
FRANCE HIGH
ITALY LOW
HOLLAND HIGH
NORWAY HIGH
SWEDEN HIGH
U.K. LOW
BELGIUM HIGH
Settings
Cleaning
Traditional
Appliance and display settings
Power
Language
Time
Appliance and display settings
High
Low
Over 2.5 kW
9
Safeguarding the environment
Disposal of packing materials
The packaging materials are 100% recyclable
and are marked with the recycling symbol
().
The various parts of the packing must therefore
be disposed of responsibly and in full
compliance with local authority regulations
governing waste disposal.
Appliance scrapping
This appliance is marked according to the
European Directive 2002/96/EC, Waste
Electrical and Electronic Equipment (WEEE).
By ensuring correct disposal of the product, the
user can help prevent potential negative
consequences for the environment and human
health.
The symbol on the product or on the
accompanying documentation indicates that it
should not be treated as domestic waste but
must be taken to an appropriate collection
centre for the recycling of electrical and
electronic equipment.
Energy saving
Only preheat the oven if specified in the
cooking table or your recipe.
Use dark lacquered or enamelled baking moulds
as they absorb heat far better.
This oven, which is intended to come into contact with foodstuffs, complies with European Regulation
( ) n.1935/2004 and has been designed, manufactured and sold in conformity with the safety
requirements of the "Low Voltage" directive 2006/95/CE (which replaces 73/23/CEE and subsequent
amendments) and the protection requirements of "EMC" directive "EMC" 2004/108/CE.
EC Declaration of conformity
The oven does not work:
Check for the presence of mains electrical power and if the oven is connected to the electrical supply.
Switch the oven off and then on again to see if the fault has been eliminated.
The electronic programmer does not work:
If the display shows the letter " F " followed by a number, contact your nearest After-Sales Service.
Specify in this case the number after the letter " F ".
Troubleshooting Guide
10
Before contacting the After-Sales Service:
1. See if you can solve the problem yourself with
the help of the suggestions given in the
"Troubleshooting guide".
2. Switch the appliance off and then on again it to
see if the problem has been eliminated.
If the fault persists after the above checks,
contact the nearest After-Sales Service.
Always specify:
a brief description of the fault;
the type and exact model of the oven;
the service number (number after the word
Service on the rating plate), located on the right
hand edge of the oven cavity (visible when the
oven door is open). The service number is also
indicated on the guarantee booklet;
your full address;
your telephone number.
If any repairs are required, contact an authorized
Service Centre (to guarantee the use of original
spare parts and correct repair).
After-Sales Service
Cleaning
- Do not use steam cleaners.
- Only clean the oven when it is cool to the
touch.
- Disconnect the appliance from the mains
power supply.
Oven exterior
IMPORTANT: do not use corrosive or abrasive
detergents. If any of these products
unintentionally comes into contact with the
appliance, clean immediately with a damp
microfibre cloth.
Clean the surfaces with a damp microfibre cloth.
If it is very dirty, add a few drops of washing up
detergent to the water. Finish off with a dry
cloth.
Oven interior
IMPORTANT: do not use abrasive sponges or
metallic scrapers or scourers. Over time, these
can ruin enamelled surfaces and the oven door
glass.
After every use, allow the oven to cool then
clean it preferably while it is still warm in order
to remove built-up dirt and stains caused by food
residues (e.g. food with a high sugar content).
Use proprietary oven detergents and follow the
manufacturer's instructions to the letter.
Clean the door glass with a suitable liquid
detergent. The oven door can be removed to
facilitate cleaning (see MAINTENANCE).
N.B: during prolonged cooking of foods with a
high water content (e.g. pizza, vegetables,
etc.) condensation may form
on the inside of the door and around the seal.
When the oven is cold, dry the inside of the
door with a cloth or sponge.
Accessories:
Soak the accessories in water with washing up
detergent immediately after use, handling them
with oven gloves if still hot.
Food residues can be easily removed using a
washing-up brush or sponge.
Cleaning cycle of ovens with pyrolysis function
(if present):
- Do not touch the oven during the pyrolysis
cycle.
- Keep children away from the oven during
the pyrolysis cycle
This function burns off spatters produced inside the
oven during cooking at a temperature of approx.
500°C. At this high temperature, the deposits turn
into a light ash which can be easily wiped away with
a damp cloth, once the oven is cool.
Do not select the pyrolysis function after every use,
only when the oven is very dirty or produces smoke
WARNING
WARNING
11
Cleaning
or fumes while preheating or cooking.
If the oven is installed below a hob, make sure
that all burners or electric hotplates are switched
off during the self-cleaning (pyrolysis) function.
Remove all accessories before running the
pyrolysis function.
For optimum cleaning of the oven door, remove
the worst soiling with a damp sponge before
using the pyrolytic function.
The appliance is equipped with 2 pyrolysis functions:
1. Energy-saving cycle (PYRO EXPRESS/ECO):
which consumes approximately 25% less energy
than the standard cycle. Select it at regular
intervals (after cooking meat on 2 or 3
consecutive occasions).
2. Standard cycle (PYRO): which is suitable for
cleaning a very dirty oven.
In any case, after a certain number of uses and
depending on how dirty the oven is, a message
on the oven display advises you to run a self-
cleaning cycle.
N.B: during the pyrolysis function, the oven
door will not open; it will remain locked until
the temperature inside the oven has returned
to an acceptably safe level.
- Use safety gloves.
- Ensure the oven is cold before carrying out the following
operations.
- Disconnect the appliance from the mains power supply.
REMOVING THE DOOR
To remove the door:
1. Open the door fully.
2. Lift the catches and push them forwards as far as they will go (fig. 1).
3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is
released (D) (fig. 2).
To refit the door:
1. Insert the hinges in their seats.
2. Open the door fully.
3. Lower the two catches.
4. Close the door.
WARNING
Maintenance
(fig. 1)
(fig. 2)
12
REMOVING THE SIDE GRILLES
The side accessory-holder grilles are equipped with two fixing screws (fig. 3)
for optimum stability.
1. Remove the screws and relative plates on the right and left with the aid
of a coin or tool (fig. 4).
2. To remove the grilles, lift them up (1) and turn them (2) as shown in
fig. 5.
REPLACING THE LAMP
To replace the rear lamp (if present):
1. Disconnect the oven from the mains power supply.
2. Unscrew the lamp cover, replace the lamp (see note for lamp type) and
screw the lamp cover back on.
3. Reconnect the oven to the power supply.
N.B:
- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-
40W/230 V type G9, T300°C halogen lamps.
- Lamps are available from our After-Sales Service.
IMPORTANT:
- If using halogen lamps, do not handle with bare hands
sincefingerprints can damage them.
- Do not use the oven until the lamp cover has been repositioned.
Maintenance
(fig. 3)
(fig. 4)
(fig. 5)
13
FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION
1. Control panel
2. Upper heating element/grill
3. Cooling fan (not visible)
4. Dataplate (not to be removed)
5. Lamps
6. Circular heating element (not visible)
7. Fan
8. Rotisserie (if supplied)
9. Bottom heating element (not visible)
10. Door
11. Position of shelves (the number of shelves is indicated on the front of the oven)
12. Rear wall
13. Meat probe connection
N.B:
- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.
- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a
while.
- When the oven door is opened during cooking, the heating elements switch off.
Instructions for oven use
1
12
5
2
4
13
8
9
11
10
7
6
3
14
ACCESSORIES SUPPLIED
A. WIRE SHELF (n. 1): the wire shelf can be used to grill food or as a
support for pans, cake tins and other ovenproof cooking receptacles.
B. DRIP TRAY (n. 1): the drip tray is designed to be positioned under the
wire shelf in order to collect fat or as an oven tray for cooking meat,
fish, vegetables, focaccia, etc.
C. BAKING TRAY (n. 1): for cooking all bread and pastry products, but
also roasts, fish en papillotte, etc.
D. MEAT PROBE: to measure the core temperature of food during
cooking.
E. ROTISSERIE (n. 1): for uniform roasting of large pieces of meat and
poultry.
ACCESSORIES NOT SUPPLIED
Other accessories can be purchased separately from the After-Sales Service.
Instructions for oven use
(Fig. A)
(Fig. B)
(Fig. C)
(Fig. D)
(Fig. E)
15
INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN
The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional
removal.
1. Insert the wire shelf horizontally, with the raised part "A" upwards (fig. 1).
2. Angle the wire shelf when it reaches the locking position "B" (fig. 2).
3. Return the wire shelf to the horizontal position and push it in fully to "C" (fig. 3).
4. To remove the wire shelf proceed in reverse order.
The other accessories, like the drip tray and baking tray, are inserted in exactly the same way. The
protrusion on the flat surface enables the accessories to lock in place.
Instructions for oven use
CONTROL PANEL DESCRIPTION
DISPLAY
TOUCH KEYS:
to use, simply touch the corresponding symbol
(a light touch is all that is required).
(Fig. 1)
(Fig. 2)
(Fig. 3)
ON/OFF (when you press on / off button to
turn off the oven an acoustic signal will
sound, this sound can not be disabled)
to access the main MENU or return to the
start screen
to access the 10 most used functions. For
settings, storing favourites and usage, see
paragraph "FAVOURITES"
to return to the previous screen or to save a
favourite function
to browse functions/options and adjust
pre-set values
to select and confirm settings
to start cooking
16
LIST OF FUNCTIONS
After switching on the oven, press the symbol and the display will show the following indications.
A. Symbol for highlighted function
B. Highlighted function can be selected by pressing
C. Description of highlighted function
D. Other available and selectable functions
FIRST USE - SELECTING A LANGUAGE AND SETTING THE TIME
For correct use of the oven, when it is switched on for the first time you will have to select the desired
language and set the correct time.
Proceed as follows:
1. Press : the display will show the list of the first three available languages.
2. Press buttons and to scroll down the list.
3. When the desired language is highlighted, press to select it.
After language selection, the display will flash 12:00.
4. Set the time using buttons and .
To scroll through the numbers more quickly, keep the button pressed.
5. Confirm your setting by pressing : the display will show the list of functions.
Instructions for oven use
Traditional
Professional
Special functions
Traditional manual cooking functions
A
B
D
C
FUNCTION DETAILS
After selecting the desired function, press button and the display will show further options and related
details
To move between different areas, use buttons and : the cursor moves to the adjustable values,
following the order described above.
Press to select the value, adjust it using and confirm by pressing button .
Grill
--:--
COOK TIME
Medium
GRILL POWER
No
PREHEAT
--:--
END TIME
Zone 1
Cursor
Zone 2
Zone 3
Zone 4
SETTING THE TEMPERATURE/OUTPUT OF THE GRILL
To change the temperature or output of the grill, proceed as follows:
1. Check that the cursor is positioned next to the
temperature value (zone 1); press button to
select the parameter to be changed: the
temperature values flash.
2. Use buttons and to change to the
desired value.
3. Press button to confirm and then press .
The display indicates which shelf food should be
placed on.
4. Press to start cooking.
The set temperature can also be changed during
cooking by following the same procedure.
Forced air
17
SELECTING COOKING FUNCTIONS
1. If the oven is off, press button ; the display will show the cooking functions.
2. To browse the various possibilities, press buttons and : the selectable function is highlighted in
white in the centre of the display.
N.B: for the list and description of functions, see the specific table at page 26.
3. Select the function by pressing button : the cooking settings are shown on the display. If the pre-set
values are those desired, press the start button , otherwise proceed as indicated above to change
them.
Instructions for oven use
Traditional
Professional
Special functions
Traditional manual cooking functions
--:--
COOK TIME
200°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Forced air
--:--
COOK TIME
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Insert food on level 3
Press when done
18
SELECTING OVEN PREHEATING
If you do not wish to preheat the oven, for those functions which allow it, simply change the oven's default
selection as follows:
1. Using buttons and , move the cursor to
preheating.
2. Press button to select the setting: "Yes" flashes
on the display.
3. To change the setting, press or : "No"
appears on the display.
4. To confirm your choice, press button .
Forced air
--:--
COOK TIME
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
FAST PREHEATING
If you wish to preheat the oven quickly before inserting food, change the oven's default selection as
follows:
1. Select the fast preheating function using
buttons and .
2. Confirm by pressing : the settings are
shown on the display.
3. If the proposed temperature is that
desired, press , otherwise proceed as
described in previous paragraphs to
change it. An acoustic signal will sound
when the oven has reached the set
temperature. At the end of preheating,
the oven automatically selects the
conventional function .
At this point food can be placed in the
oven for cooking.
4. If you wish to set a different cooking
function, press and select the desired
function.
Fast preheating
- 00:02
INSERT IN
180°C
TEMPERATURE
Preheating
- 00:02
INSERT IN
180°C
TEMPERATURE
Forced air
--:--
COOK TIME
180°C
TEMPERATURE
Ye s
PREHEAT
--:--
END TIME
Forced air
--:--
COOK TIME
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Oven is hot!
- 00:02
INSERT IN
180°C
TEMPERATURE
Instructions for oven use
19
SETTING COOKING TIME
This function can be used to cook food for a set length of time, from a minimum of 1 minute to the
maximum time allowed by the selected function, after
which the oven switches off automatically.
1. To select the function, position the cursor next to
"COOK TIME" using the buttons and .
2. Press button to select the setting; "00:00" flashes
on the display.
3. Change the value using buttons and to
display the desired cooking time.
4. Confirm the selected value by pressing button .
Forced air
--:--
COOK TIME
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Forced air
--:--
HH:MM
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Forced air
00:20
HH:MM
180°C
TEMPERATURE
No
PREHEAT
19:20
END TIME
BROWNING
At the end of cooking, with certain functions, the display indicates the possibility of browning the surface
of your dish. This function can only be used when
cooking time has been set.
At the end of cooking time, the display shows " to
prolong, to brown".
Press button , and the oven starts a 5 minute
browning cycle. This function can only be used once
after cooking.
Cooking finished at 20:00
to prolong, to brown
Browning
- 00:05
COOK TIME
20:05
END TIME
Browning finished at 20:05
Instructions for oven use
20
SETTING END OF COOKING TIME /DELAYED START
The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and 59
minutes. This can only be done once cooking time has been set. This setting is onlypossible when
preheating is not required for the selected function.
After setting cooking time, the display shows
the end of cooking time (for example 19:20).
To delay the end of cooking time, and thus
also the cooking start time, proceed as
follows:
1. Position the cursor next to the end of
cooking time using buttons and .
2. Press button to select the setting:
the end of cooking time flashes.
3 To delay the end of cooking time, use
buttons and to set the desired
value.
4. Confirm the selected value by pressing
button .
5. Press button : The display indicates
which shelf food should be placed on.
6. Press button to activate the function.
The oven will start cooking after a period
of time calculated so as to finish cooking
at the set time (for example, in the case of a dish which requires a cooking time of 20 minutes, if the
end of cooking time is set to 20.10, the oven will begin cooking at 19.50).
N.B: During the interval before cooking starts, the oven can in any case be switched on by
pressing button .
At any time during cooking, set values (temperature, grill setting, cooking time, end of cooking
time) can be changed using buttons and and button as described in previous
paragraphs.
Forced air
- 00:20
HH:MM
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Forced air
- 00:20
HH:MM
180°C
TEMPERATURE
No
PREHEAT
--:--
END TIME
Forced air
- 00:20
HH:MM
180°C
TEMPERATURE
No
PREHEAT
20:10
END TIME
Instructions for oven use
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

KitchenAid KOLP 7105 User guide

Category
Kitchen & houseware accessories
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI