No Brand PLINTH900H Installation guide

Brand: No Brand

Model: PLINTH900H

Type: Installation guide

It is recommended to install this plinth accessory if the adjacent kitchen bench height is greater than 850mm.

The plinth will lift the cooker up from a nominal height of 850mm to 900mm, creating better alignment of the

cooker hob with the bench. This may eliminate the need to leave 100mm clearance each side of the cooker,

which is needed only if the cooker hob height is below the adjacent bench height upon installation (refer

Instructions for the installer section in main instruction manual for more details).

IMPORTANT: The plinth must be installed before fitting the stability bracket to the back wall.

For use only with cooker models: EKM6700X, EKM6701X & EKC6707X

Plinth installation instructions

1. If the appliance is provided with a frontal

plastic base at the bottom, disengage it from

the appliance and remove it.

2. Carefully tilt the appliance backwards and

slowly lay it down on its back, taking care

not to cause any stress or damage

3. Using a Torx 20 head screw driver remove

the 2 fixing screws from the 2 metal “Anti-tip”

feet (letter “A”). Keep the screws, and

remove the metal feet. Then unscrew the 2

black plastic feet (letter “B”) and remove

them too.

4. Use the 2 previously removed fixing

screws and place them back in their relevant

holes, as shown in the diagram.

5. Unpack the accessory plinth

FRONT

6. Secure the accessory plinth to the bottom

of the appliance by means of the four

supplied fixing screws. Ensure that the

front side of the plinth with the “safety

screw” (“C”) is positioned to match

the front side of the cooker, as shown in

diagram.

7. Screw the 2 previously removed plastic

feet to the bottom of the plinth, take the

other 2 supplied plastic feet, and screw them

to the bottom of the plinth as well. Turn the

“safety screw” so that it comes out the plinth

for about 1 cm.

FRONT

Appliance

Plinth

8. Lift the cooker upright and push it into the

intended position so that the back of the hob

is 40mm from the back wall. Mark the

position for the “safety screw” hole on the

floor, and mark the cooker heght on the back

wall taken from the top of the trivets (splash

back removed)

9. Drill a hole of 5mm diameter and depth 15mm where you marked the point on the ground.

11. Fix the stability bracket (using two of the

provided five fixing holes) to rear wall (see

diagram).

12. Pull the cooker towards the rear wall as

shown in the diagram. The stability bracket

should then come into contact with the

bottom panel of the cooker.

13. Remove the drawer, reach the head of

the “safety screw” from the inner side of the

plinth and fully screw it into the hole in the

ground.

14. If the appliance is provided with a frontal

plastic base at the bottom, re-fit the base

back to its position.

15. Check that the stability bracket securely

prevents the cooker from accidently tipping

forward when a downward force is applied to

the open oven door. Check that the safety

screw securely prevents the cooker from

accidentally being pulled forward.

10. Mark 760mm or 750mm depending on

model (see diagram) below the cooker

height. This is the position of the stability

bracket.

SIDE VIEW

OF THE COOKER

BASE OF COOKER

ENGAGEMENT EDGE FOR

STABILITY BRACKET

BACK OF COOKER

720mm

760mm

40mm

SIDE VIEW

OF THE COOKER

BASE OF COOKER

ENGAGEMENT EDGE FOR

STABILITY BRACKET

BACK OF COOKER

720mm

750mm

In order to prevent accidental tipping

of this appliance, for example by a

child climbing on to the open oven

door, the stabilising means MUST be

correctly installed, as per instruction below:

Fitting the Stability Bracket

For model EKC 6707X

For model EKM 6700X &

EKM 6701

40mm

35670-2412

No Brand PLINTH900H Installation guide

No Brand PLINTH900H Installation guide

No Brand PLINTH900H Installation guide

Other documents