SolrenView PVI 36TL Installation guide

Brand: SolrenView

Model: PVI 36TL

Type: Installation guide

SolrenView PVI 36TL is a monitoring DAS device designed to be installed into compatible inverters, providing remote monitoring capabilities and data logging. It features an Ethernet connection for data transmission and a 5-pin green connector for local communication within the inverter. The device is designed to be installed by a qualified electrician, following specific safety protocols such as disconnecting AC/DC disconnects and observing electrical safety practices.

SolrenView PVI 36TL is a monitoring DAS device designed to be installed into compatible inverters, providing remote monitoring capabilities and data logging. It features an Ethernet connection for data transmission and a 5-pin green connector for local communication within the inverter. The device is designed to be installed by a qualified electrician, following specific safety protocols such as disconnecting AC/DC disconnects and observing electrical safety practices.

SolrenView Installation Guide PVI 14-36TL Series

DOCR-070580-A Page 1 of 5

SolrenView Installation Guide

for PVI 14-36TL Inverters

Revision A

©2015, Solectria – A Yaskawa Company

SolrenView Installation Guide PVI 14-36TL Series

DOCR-070580-A Page 2 of 5

This installation guide provides instructions on installing the SolrenView monitoring DAS into

the inverter.

Required tools:

3mm Allen wrench (non-powered)

#2 Phillips screwdriver

REMOVING THE WIRING BOX COVER

PVI 23/28/36TL Inverters

1. Disconnect AC/DC disconnects.

2. Wait 5 minutes for capacitors to discharge.

3. Note that all fuses are still live.

4. Use standard electrical safety practices while performing the job.

Use a 3mm Allen bit to loosen the

wiring box cover. Do NOT use an

electric screw driver. Remove the

cover.

PVI 23/28/36TL

SolrenView Installation Guide PVI 14-36TL Series

DOCR-070580-A Page 3 of 5

REMOVING THE WIRING BOX COVER

PVI 14/20TL Inverters

1. Disconnect AC/DC disconnects.

2. Wait 5 minutes for capacitors to discharge.

3. Note that all fuses are still live.

4. Use standard electrical safety practices while performing the job.

Using #2 Phillips screwdriver,

remove the 6 screws holding the

cover to the chassis. Retain

hardware for later use.

PVI 14/20TL

SolrenView Installation Guide PVI 14-36TL Series

DOCR-070580-A Page 4 of 5

SOLRENVIEW INSTALLATION INSTRUCTIONS

PVI 23/28/36TL

1

2

3

4

5

Pre-bend the wire harness as shown.

Place the data logger in its location.

Insert the provided hardware in the

4 locations shown. Correct

sequence: screw, lock washer, flat

washer. Torque to 8 in-lbs.

Add Ethernet connection

prior to mounting DAS.

Connect the 5 pin green connector.

Replace the cover and torque to 16 in-lbs.

SolrenView Installation Guide PVI 14-36TL Series

DOCR-070580-A Page 5 of 5

SOLRENVIEW INSTALLATION INSTRUCTIONS

PVI 14/20TL

4

3

2

1

Loosen and discard right standoff.

Insert the provided hardware in the 3

locations shown. Correct sequence:

screw, lock washer, flat washer.

Torque to 8 in-lbs.

Connect the 5 pin green connector.

Add Ethernet connection.

Replace the cover and torque to 10 in-lbs.

1
2
3
4
5

SolrenView PVI 36TL Installation guide

Brand: SolrenView

Model: PVI 36TL

Type: Installation guide

SolrenView PVI 36TL is a monitoring DAS device designed to be installed into compatible inverters, providing remote monitoring capabilities and data logging. It features an Ethernet connection for data transmission and a 5-pin green connector for local communication within the inverter. The device is designed to be installed by a qualified electrician, following specific safety protocols such as disconnecting AC/DC disconnects and observing electrical safety practices.

Download PDF

Other documents