Front Runner TBMK023 Installation guide

Brand
Front Runner
Model
TBMK023
Category
Car kits
Type
Installation guide

This manual is also suitable for

TBMK022_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
front runner
TBMK022
TBMK023
TBMK024
ENG
1
Thank you for purchasing a Front Runner Tent Mount Kit 2 Piece Tall.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
TENT MOUNT KIT 2 PIECE TALL
TBMK022_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX
1 2 X Tent Mount Bracket - Tall
2 4 X M8 x 16 Hex Head Bolt
3 6 X M8 x 25 x 2 Flat Washer
4 6 X M8 Nyloc Nut
5 2 X M8 x 25 Hex head Bolt
6 6 X M8 Nut Cap
6
4
3
1
2
3
4
6
5
13mm
3
4
1
2
4
3
5
TBMK025_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE
2
2.1
2.2
2.3
Depending on the tent opening and orienta-
tion the tent base channels may need to be
rotated.
Taking into acount the length and width
of your tent,choose where you'd like to
position it on the rack, this will determine
where you need to fit the Tent Mount
Brackets (Item 1)
Loosely assemble the Tent Mount Brackets
(Item 1) to the rack using Channel Nuts
(Supplied with the Tent) M8 x 16 Hex Head
Bolts, M8 x 25 x 2 Flat Washers and M8
Nyloc Nuts (Items 2, 3 & 4).
Loosely assemble the Tent to the Tent Mount
Kits (Item 1) using M8 x 25 Hex Head Bolt,
M8 x 25 x 2 Flat Washers and M8 Nyloc Nuts
(Items 3, 4 & 5).
Where possible use the combined slats
to mount the brackets. If this is not
possible then a slat with a leg or foot
installed.
For larger & heavier tents additional
mounting brackets may be required.
13mm
13mm
Tent Channels must run across the
Bracket Bends.
Channel Nut
Lorem ipsum
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
TBMK025_REV_A00 © 2022 FRONT RUNNER VEHICLE OUTFITTERS
4
FIT AND SECURE
2
2.1
Center the tent left to right and front to rear
then fully thighten all fasteners.
Place M8 Nut Caps (Item 6) over all Hex
Head Bolts.
13mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Front Runner TBMK023 Installation guide

Brand
Front Runner
Model
TBMK023
Category
Car kits
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers