Crystal Vision MultiLogo V130 User manual

Crystal Vision Ltd., Lion Technology Park, Station Road East, Whittlesford, Cambridge, CB22 4WL, England.

E-mail: [email protected] Website: www.crystalvision.tv Tel: +44(0) 1223 497049 Fax: +44(0) 1223 497059

MultiLogo

HD/SD logo keyer

MultiLogo User Manual R1.2 Crystal Vision

1 19/01/2009

Contents

1Introduction 3

1.1Operating modes 4

Input and output video standards 4

2Hardware installation 5

2.1Module configuration 5

2.2Rear modules and signal I/O 6

Rear module connections with RM44 7

Rear module connections with RM52 7

Rear module connections with RM34 8

2.3General Purpose Interface (GPI) 9

Using MultiLogo GPIs 9

3PC control 13

3.1Installing MultiLogo software 13

MultiLogo - Setting IP Address 13

Installing Operating Software 14

Pointing the LogoKeyer Software at the boards 16

Uploading Files into RAM and Flash Storage 16

Assigning RAM and Flash files to Keyers 17

Viewing the Cards RAM and Flash sources 17

Setting the Key gains 18

Positioning the Graphics from the Memory Stores 18

Recording from external video inputs 18

Saving and Recalling presets 18

3.2Image converter 19

Using the image converter 19

MultiLogo User Manual R1.2 Crystal Vision

2 19/01/2009

3.3Updating MultiLogo software 21

Upgrading the MultiLogo board software 21

Updating MultiLogo PC software 23

4Card edge operation 26

4.1Card edge switch settings 26

4.2Card edge rotary controls 26

4.1Reading card edge LEDs 27

4.2Navigating card edge menus 27

Menu tree 28

Status menu 28

IP Address 29

Board Mode 29

5Using the front control panel 30

5.1Module selected 30

Updating the display 31

5.2The MultiLogo active panel menu structure 32

Status Menu 33

6Trouble shooting 34

6.1Card edge status LEDs 34

Basic fault finding guide 35

7Specification 36

Revision 1. Image converter information added 14-11-08

Software update information added

Board edge menu updated

Revision 2. RM44 information added 09-01-09

RM52 information amended

Crystal Vision Introduction

MultiLogo User Manual R1.2 3 19/01/2009

1 Introduction

MultiLogo is a sophisticated modular logo keyer that provides three layers of keying from

a variety of internal and external sources. Its multi-port non-volatile video store can read

six images and write two images simultaneously. There are two versions of MultiLogo

available, the MultiLogo V130 with a single HD/SD video input and the MultiLogo V430

that has four HD/SD video inputs.

MultiLogo can be used either with graphics that have a separate key signal or with self-

keyed graphics. Both additive and multiplicative keying is available. Three layer keying

allows three still or animated graphics to be independently brought up either from the

video store or from external sources. The first external video source is normally dedicated

to the main programme because of its relay bypass protection while the other three

external feeds (MultiLogo V430 only) are completely flexible and configurable. Typically

these inputs could be used for such things as a back-up feed or character generator for an

emergency message and its key signal. It is also possible to grab a logo from a live video

feed.

MultiLogo runs the uCLinux operating system for sophisticated file handling and stability

and with on-board industry standard protocols allowing it to be used with studio

automation systems. Alternately, using a PC running Crystal Vision’s own drag and drop

software will auto-convert images of most common file formats required by the

MultiLogo and transfer them over 100MB Ethernet directly onto the board via its

dedicated rear module RJ45 Ethernet connection.

MultiLogo is designed for branding HD or SD stations but for people who just need one

station ident the V430 can be used as a dual channel device – sharing the three keyers

between two channels. Both versions share a look-ahead preview facility, which has the

benefit of allowing sophisticated transitions to be previewed before committing to the

main output.

MultiLogo

Crystal Vision Introduction

MultiLogo User Manual R1.2 4 19/01/2009

MultiLogo’s main features are:

• Modular logo keyer, available in two versions

• Three layers of keying

• Eight-port video store with DRAM and Flash memory

• Graphics can have separate key signal or be self-keyed

• Additive and multiplicative keying

• Up to four configurable external inputs for live video (MultiLogo V430)

• Drag and drop PC software for auto conversion of graphics from any format

• Fast transfer of graphics from PC to board over 100 MB Ethernet

• Look-ahead preview

• Industry standard software protocols help use with automation systems

• Can be used as a dual channel logo keyer where one layer of keying is required

(MultiLogo V430)

• Relay bypass protection of main input (RM52)

MultiLogo is a 100mm x 266mm module, which fits in the four standard frames and can

be integrated with any boards from the company’s full product range. MultiLogo V130 is

a single height module and can be used with either the RM44 or RM52 rear module, both

of which include relay bypass protection of the input in the event of power failure or

board malfunction or removal. The MultiLogo V430 is a ‘double decker’ module and

requires an RM34 rear connector in its upper position in combination with either the

RM44 or RM52 rear module in the lower position.

1.1 Operating modes

Input and output video standards

The MultiLogo will automatically switch between SD-SDI and HD-SDI inputs. The

output timing is locked to the input. (Input 1on the lower rear module RM52 of a

MultiLogo V430).

Note: All inputs of the MultiLogo V430 must be of the same standard and co-timed to within one

line.

If the MultiLogo is powered without an input it will default to outputting 1080i 50. To

change the output to 1080i/720p 59.94 momentarily, apply a 1080i/720p 59.94 input to

Input 1 so that the MultiLogo can relock.

Should graphics have been copied into the RAM/Flash with an HD-SDI input connected

those graphics will no longer be valid if the input is changed to SD-SDI as the graphics

resolution will have been determined by its input standard.

Note: MultiLogo’s memory store can contain graphics of all supported video standards but they

will only be valid in their native standard.

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 5 19/01/2009

2 Hardware installation

The MultiLogo V130 single height module uses either the RM44 or RM52 rear connector

that will fit into all Crystal Vision rack frames. The MultiLogo V430 is a ‘double decker’

module that uses either an RM52 plus RM34 or RM44 plus RM34 rear module. The

MultiLogo V430 takes up two frame slots. All modules can be plugged in and removed

while the frame is powered without damage.

2.1 Module configuration

The MultiLogo V130

MultiLogoV130

The MultiLogo V430

MultiLogoV430

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 6 19/01/2009

MultiLogoV130/430 underside showing the flash memory module fitted

Link configuration and LEDs

There are six jumper links and four surface-mounted LEDs on the MultiLogo

motherboard. The surface-mounted LEDs are not visible from the front of the frame and

are included for diagnostic purposes only.

Comment

PL4, PL5, PL6, PL7 GPI/RS422 comms.

GP1 pins 2-3 (right position). RS422 pins 1-2 (left position).

Factory set for GPI

PL8 1-2 selected IP address. 2-3 forced IP address 10-0-0-201

PL9 (under side) Not applicable

LED1 Input present

LED4 CPU configuration in progress

LED5 Ethernet Data

LED6 Ethernet Link

2.2 Rear modules and signal I/O

The Indigo 4 4U frame will house up to 24 single height or 12 double height modules

with up to three power supplies. The Indigo 2 2U frames will house up to 12 single height

or six double height modules and dual power supplies. The Indigo 1 1U frames will house

six single height or three double height modules and a single power supply. The Indigo

DT desk top boxes have a built-in power supply and will house up to two single height or

one double height modules.

Note: For details of fitting rear connectors please refer to the appropriate frame manual.

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 7 19/01/2009

Rear module connections with RM44

The RM44 is a single height module that is used for the MultiLogo V130 and as the lower

rear connector for the MultiLogo V430.

RM44 rear module connector Description

RM44

• 24 MultiLogo V130 modules per

Indigo 4 frame

• 12 per Indigo 2 frame

• Six per Indigo 1 frame

• Two per Indigo DT

• All frame slots can be used

BNC I/O assignment

Ethernet connector Ethernet control from PC

PREVIEW Preview output

MAIN OUT2 (Unswitched) Serial digital output with no relay bypass

MAIN OUT1 (Switched) Serial digital output with relay bypass

HD/SD IN High Definition/Standard Definition serial digital input

Rear module connections with RM52

The RM52 is a single height module that is used for the MultiLogo V130 and as the lower

rear connector for the MultiLogo V430.

RM52 rear module connector Description

RM52

• 24 MultiLogo V130 modules per

Indigo 4 frame

• 12 per Indigo 2 frame

• Six per Indigo 1 frame

• Two per Indigo DT

• All frame slots can be used

BNC I/O assignment

Ethernet connector Ethernet control from PC

Ethernet connector RS422 control from control panel

PREVIEW Preview output

MAIN OUT2 (Unswitched) Serial digital output with no relay bypass

MAIN OUT1 (Switched) Serial digital output with relay bypass

HD/SD IN High Definition/Standard Definition serial digital input

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 8 19/01/2009

Rear module connections with RM34

The RM34 is a single height module that is used as the upper rear connector for the

MultiLogo V430.

RM34 rear module connector Description

RM34

• 12 MultiLogo V430 modules per

Indigo 4 frame

• Six per Indigo 2 frame

• Three per Indigo 1 frame

• One per Indigo DT

• Alternate frame slots can be used

BNC I/O assignment

AES OUT 1 Not currently supported

AES OUT 2 Not currently supported

AES INPUT Not currently supported

HD/SD IN D Configurable High Definition/Standard Definition serial digital input

HD/SD IN C Configurable High Definition/Standard Definition serial digital input

HD/SD IN B Configurable High Definition/Standard Definition serial digital input

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 9 19/01/2009

2.3 General Purpose Interface (GPI)

Each frame slot has up to six connections ‘a-f ‘for GPI control and monitoring. These

connections are available at the rear of the frame on the 26-way D-type remote

connectors.

Note: For MultiLogo V430 the GPI’s connect to the lower slot position. E.g. if the MultiLogo

V430 was located in slot positions 1 and 2 you would wire to slot 2.

GPI Low (<1V) High (+5V)

0 ‘a’ Recall preset bit 1 The seven user preset configurations can be

recalled using binary notation

1 ‘b’ Recall preset bit 2

2 ‘c’ Recall preset bit 4

3 ‘d’ Mix (auto) On transitions toggles the programme and

preview control at a rate set by the rate control

4 ‘e’ Not used

5 ‘f’ No connection

As supplied, each GPI output has a 220Ω resistor in series with its output. This allows for

an external LED to be driven, connected to a DC voltage of +5V.

The recall presets with GPI control must be enabled from the user controls, i.e. card edge,

active front panel or Statesman PC control system.

Using MultiLogo GPIs

There are a total of 225 presets available on the MultiLogo but it is only possible to call

the first seven using the GPI inputs. The following table shows the binary weighted code

required to recall presets 1 to 7.

A ‘0’ is an open GPI input and a ‘1’ is a grounded GPI input. The GPIs are momentary

i.e. a pulse to ground is required to action a change rather than a latch to ground.

GPI input connections have 10kΩ pull-up resistors to the internal chassis +5V.

Recall Preset No change 1 2 3 4 5 6 7

GPI ‘a’ 0 1 0 1 0 1 0 1

GPI ‘b’ 0 0 1 1 0 0 1 1

GPI ‘c’ 0 0 0 0 1 1 1 1

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 10 19/01/2009

4U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of eight rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

3 8 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)

4 7 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)

5 5 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

6 4 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

7 5 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)

8 4 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)

9 3 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)

12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (5) 9 (5) 18 (5) 26 (5) 19 (6) 20 (6)

2 7 (5) 16 (5) 17 (5) 25 (5) 10 (6) 11 (6)

3 8 (7) 9 (7) 18 (7) 26 (7) 19 (8) 20 (8)

4 7 (7) 16 (7) 17 (7) 25 (7) 10 (8) 11 (8)

5 5 (5) 6 (5) 15 (5) 24 (5) 1 (6) 2 (6)

6 4 (5) 14 (5) 13 (5) 23 (5) 3 (6) 4 (6)

7 5 (7) 6 (7) 15 (7) 24 (7) 1 (8) 2 (8)

8 4 (7) 14 (7) 13 (7) 23 (7) 3 (8) 4 (8)

9 3 (5) 12 (5) 22 (5) 21 (5) 12 (6) 13 (6)

10 10 (5) 11 (5) 19 (5) 20 (5) 21 (6) 22 (6)

11 3 (7) 12 (7) 22 (7) 21 (7) 12 (8) 13 (8)

12 10 (7) 11 (7) 19 (7) 20 (7) 21 (8) 22 (8)

Table shows pin number (Remote number)

Note: Remote 1, Remote 3, Remote 5 and Remote 7 are 26 way high-density D-Type female

sockets. Frame ground is pin 2 and +5V @500mA is pin 1 in each case.

Remote 2, Remote 4, Remote 6 and Remote 8 are 26 way high-density D-Type male

plugs and frame ground is pin 6 in each case and +5V @500mA is pin 15 on Remote 2

and Remote 6.

The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-4 to approximately 1A. Remotes 5-8 are similarly

protected.

Upper Lower

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 11 19/01/2009

2U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of four rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

3 8 (3) 9 (3) 18 (3) 26 (3) 19 (4) 20 (4)

4 7 (3) 16 (3) 17 (3) 25 (3) 10 (4) 11 (4)

5 5 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

6 4 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

7 5 (3) 6 (3) 15 (3) 24 (3) 1 (4) 2 (4)

8 4 (3) 14 (3) 13 (3) 23 (3) 3 (4) 4 (4)

9 3 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

10 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

11 3 (3) 12 (3) 22 (3) 21 (3) 12 (4) 13 (4)

12 10 (3) 11 (3) 19 (3) 20 (3) 21 (4) 22 (4)

Table shows pin number (remote number)

Note: Remote 1 and Remote 3 are 26 way high-density D-Type female sockets. Frame ground

is pin 2 and +5V @500mA is pin 1 in each case.

Remote 2 and Remote 4 are 26 way high-density D-Type male plugs and frame ground is

pin 6 in each case and +5V @500mA is pin 15 on Remote 2.

The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-4 to approximately 1A.

1U frame GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to one of two rear remote connectors as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

3 5 (1) 6 (1) 15 (1) 24 (1) 1 (2) 2 (2)

4 4 (1) 14 (1) 13 (1) 23 (1) 3 (2) 4 (2)

5 3 (1) 12 (1) 22 (1) 21 (1) 12 (2) 13 (2)

6 10 (1) 11 (1) 19 (1) 20 (1) 21 (2) 22 (2)

Table shows pin number (remote number)

Note: Remote 1: 26 way high-density D-Type female socket. Frame ground is pin 2 and +5V

@500mA is pin 1.

Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V

@500mA is pin 15

The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-2 to approximately 1A.

Crystal Vision Hardware installation

MultiLogo User Manual R1.2 12 19/01/2009

Indigo DT desk top box GPI connections

GPI lines ‘a’ to ‘f’ of each card connect to the rear remote connector as follows:

Slot no. ‘a’ pin ‘b’ pin ‘c’ pin ‘d’ pin ‘e’ pin ‘f’ pin

1 8 (1) 9 (1) 18 (1) 26 (1) 19 (2) 20 (2)

2 7 (1) 16 (1) 17 (1) 25 (1) 10 (2) 11 (2)

Table shows pin number (remote number)

Note: Remote 1: 26 way high-density D-Type female socket. Frame ground is pin 2 and +5V

@500mA is pin 1.

Remote 2: 26 way high-density D-Type male plugs and frame ground is pin 6 and +5V

@500mA is pin 15

The +5V output is protected by self-resetting thermal fuses, which limit the total output

current available from Remotes 1-2 to approximately 1A.

Example connections: If a MultiLogo V430 was located in slot position 1 & 2 the GPIs

should be wired to slot position 2 (the main board). The preset recall GPIs are ‘a’, ‘b’ and

‘c’ so by referring to the table above we can see pins 7, 16 and 17 on the Remote 1 frame

D-Type will need pulling to ground to action preset recalls.

Crystal Vision PC control

MultiLogo User Manual R1.2 13 19/01/2009

3 PC control

The MultiLogo is shipped with Crystal Vision’s own drag and drop software that allows

easy board control and files conversion.

3.1 Installing MultiLogo software

MultiLogo - Setting IP Address

The unit is shipped using the following IP address 10.0.0.201. To set it to the IP of your

choice, in your web browser enter the address http://10.0.0.201/

N.B. You will need to set your PC on the same IP address and subnet mask range.

Once the status page is displayed, click on the ‘Network’ button. In the IP address field

enter the IP address you wish, along with the appropriate subnet mask and default

gateway.

Once the information has been entered click store. You will then need to reboot the card

to complete the update.

Crystal Vision PC control

MultiLogo User Manual R1.2 14 19/01/2009

Installing Operating Software

Run the ‘Setup.exe’

Click ‘Next’

To continue with the default options click ‘Next’, otherwise change the options to suite

your needs.

Crystal Vision PC control

MultiLogo User Manual R1.2 15 19/01/2009

Click ‘Next’ to start the installation process.

Once the installer has completed click ‘Close’

Crystal Vision PC control

MultiLogo User Manual R1.2 16 19/01/2009

Pointing the LogoKeyer Software at the boards

Upon installation a shortcut is placed on the desktop called LogoKeyer. This shortcut

needs to be pointed at the board’s IP address in order to communicate. To do this:

1. Right click on the shortcut and select ‘Properties’

2. After the text "C:\Program Files\LogoKeyer\Release\LogoKeyer.exe" in the

target field, enter a space followed by the IP address of the board you wish to

control.

3. Click ‘Apply’ then ‘OK’

To run the software simply double-click on the icon.

If you have more than one board in your system you can create multiple icons to control

multiple boards. To do so copy the shortcut and follow the instructions above but replace

the IP address for the board you wish to control.

Uploading Files into RAM and Flash Storage

You can upload still and moving images on to both the Flash and RAM storage.

1. Open the LogoKeyer software

2. From within the store tab, browse in the top left hand pane to the folder that

contains the images you wish to upload.

To upload the image simply drag and drop it into either the bottom right-hand window for

the Flash storage or the second from bottom right-hand window for the RAM storage.

Note: On reboot of the card any data saved in RAM will be lost. Any data in Flash will copy

itself from Flash into RAM

Crystal Vision PC control

MultiLogo User Manual R1.2 17 19/01/2009

Assigning RAM and Flash files to Keyers

1. Click on the store you wish to assign an image to (either RAM 1, 2, 3 or 4 or

Flash 1 or 2).

2. Double click the image you wish to assign to the appropriate store.

Viewing the Cards RAM and Flash sources

Once you have assigned the RAM and Flash stores images you can then assign these to

the keys.

1. Click on the ‘Mixer’ tab. The mixer tab allows you to switch between multiple

sources.



2. Click on the appropriate source under the key you are creating. If it is from the

RAM or Flash source the file name is displayed on the right.



3. You then select this key to be displayed on the foreground for the Program or the

Preset by toggling the appropriate button.



Crystal Vision PC control

MultiLogo User Manual R1.2 18 19/01/2009

Setting the Key gains

The Keyers tab allows you to set the gain and mode for each of the three Keyers.

The Key modes consist of Self Key, Split Key and Full Key.

Self key doesn’t use a key signal. It uses the luminosity in the fill signal to generate the

key information.

Split key uses both the fill and key signal to generate the key.

Full key doesn’t use a key signal but internally generates a full frame peak white signal to

force the key.

Positioning the Graphics from the Memory Stores

The Players tab allows you to change the on-screen position of the graphics from the

RAM and Flash memory stores.

If two adjacent stores are outputting the Fill and Key signal e.g. RAM 1 = Fill & RAM 2

= Key then the stores should be locked together when changing the position e.g. lock the

position of RAM 2 to RAM 1 using the “Lock to 1” control.

The Animation controls within the Players tab provides control of how to play out the

graphic from the memory stores e.g. play the file once, play the file on a continuous loop.

Recording from external video inputs

The MultiLogo can record fill and key signals from external video inputs using the

Recorders tab. N.B. Recording from inputs 2, 3 and 4 is only available on the MultiLogo

V430.

You can configure the recorder to record the fill only, key only or fill & key using the

“Source” box to select which inputs you want to use as the fill and key. The number of

frames you wish to record should be entered in the “Frames” box pressing enter after

setting your value.

Saving and Recalling presets

Up to seven presets can be stored allowing recall from the MultiLogo Control Software or

GPI. The presets store the current state of the MultiLogo including what files have been

assigned to the RAM and Flash memory, the position of the keys and the key gain

settings.

The “Save Power On” control allows you to save the state of the MultiLogo after power

up. This can then be recalled using the “Recall Power On” control, useful if you want to

get back to the power on state.

Crystal Vision PC control

MultiLogo User Manual R1.2 19 19/01/2009

3.2 Image converter

When installing the LogoKeyer GUI a program called Image Converter is also installed.

This program will convert image sequences to the native file format required by the

MultiLogo. It can also be used to extract the alpha channel from file formats that support

it. During installation an Image Converter icon will have been placed on your desktop.

Using the image converter

Launch the image converter software by either using the desktop icon or from the

MultiLogo control software file menu. Once the image converter window has opened, the

required files for conversion can be displayed by pointing the browser at the folder

containing the image files.

Image converter main screen

To make the necessary conversion, highlight the selected file. You are then required to

select the proposed output file type from the three available types. These are; Video, Key

and Video and Key.

Page is loading ...

Crystal Vision MultiLogo V130 User manual

This manual is also suitable for

Crystal Vision MultiLogo V130 User manual

Related papers

Other documents