Cypress CY4531 User manual

CY4531

EZ-PD™ CCG3 Evaluation Kit Guide

Doc. No. 002-10218 Rev. *B

Cypress Semiconductor

198 Champion Court

San Jose, CA 95134-1709

Phone (USA): 800.858.1810

Phone (Intnl): 408.943.2600

www.cypress.com

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 2

Copyrights

subsidiaries, including Spansion LLC (“Cypress”). This document, including any software or firmware included or referenced

in this document (“Software”), is owned by Cypress under the intellectual property laws and treaties of the United States

and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically

stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If

the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress

governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license

(without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form,

to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your

organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly

through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of

Cypress’s patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and

import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or

compilation of the Software is prohibited.

TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS

OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. To the extent permitted by applicable law, Cypress reserves the right to make changes to this

document without further notice. Cypress does not assume any liability arising out of the application or use of any product

or circuit described in this document. Any information provided in this document, including any sample design information or

programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly

design, program, and test the functionality and safety of any application made of this information and any resulting product.

Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended

for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical

devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances

management, or other uses where the failure of the device or system could cause personal injury, death, or property

damage (“Unintended Uses”). A critical component is any component of a device or system whose failure to perform can be

reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not

liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising

from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and

against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related

to any Unintended Uses of Cypress products.

Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM,

and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more

complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their

respective owners.

EZ-PD is a trademark of Cypress Semiconductor Corporation.

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 3

Contents

1. Introduction .................................................................................................................................................................... 7

1.1 Kit Contents ........................................................................................................................................................... 7

1.1.1 Hardware Not Included With Kit ................................................................................................................ 7

1.2 Getting Started ...................................................................................................................................................... 8

1.3 List of Recommended Hardware ........................................................................................................................... 8

1.3.1 Recommended Cables and Adapters ....................................................................................................... 8

1.4 Acronyms............................................................................................................................................................... 8

2. Kit Installation .............................................................................................................................................................. 10

2.1 CY4531 EZ-PD CCG3 EVK Kit Software Installation .......................................................................................... 10

3. CY4531 EZ-PD CCG3 EVK Hardware Details ............................................................................................................. 14

3.1 CCG EVK Base Board ......................................................................................................................................... 15

3.1.1 Block Diagram ........................................................................................................................................ 15

3.1.2 Features ................................................................................................................................................. 15

3.1.3 Connectors and Jumper Settings............................................................................................................ 16

3.2 CY4531 CCG3 Daughter Card ............................................................................................................................ 18

3.2.1 Block Diagram ........................................................................................................................................ 18

3.2.2 Features ................................................................................................................................................. 18

3.2.3 Connectors and Jumper Settings............................................................................................................ 19

3.3 Powering the CY4531 EZ-PD CCG3 EVK Setup ................................................................................................. 20

4. Programming the CCG3 Device on CY4531 CCG3 EVK ........................................................................................... 21

4.1 Programming the CCG3 Device on the CCG3 Daughter Card ............................................................................ 21

5. Kit Operation ................................................................................................................................................................ 26

5.1 SuperSpeed USB Demo ...................................................................................................................................... 26

5.1.1 Boards, Cables, and Accessories Needed ............................................................................................. 26

5.1.2 Running the SuperSpeed USB Demo ..................................................................................................... 26

5.1.3 Explanation of Functionality .................................................................................................................... 28

5.1.4 Common Problems and Troubleshooting ............................................................................................... 28

5.2 DisplayPort Demo ................................................................................................................................................ 29

5.2.1 Boards, Cables, and Accessories Needed ............................................................................................. 29

5.2.2 Running the DisplayPort Demo .............................................................................................................. 29

5.2.3 Common Problems and Troubleshooting ............................................................................................... 30

5.3 Dead Battery Demo ............................................................................................................................................. 30

5.3.1 Boards, Cables, and Accessories Needed ............................................................................................. 31

5.3.2 Running the Dead Battery Demo ............................................................................................................ 31

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 4

5.3.3 Power Supply Connections ..................................................................................................................... 32

5.3.4 Common Problems and Troubleshooting ............................................................................................... 33

6. Appendix ...................................................................................................................................................................... 35

6.1 Terminology ......................................................................................................................................................... 35

6.2 CCG3 EVK Base Board ....................................................................................................................................... 36

6.2.1 Schematics ............................................................................................................................................. 36

6.2.2 Gerber Files ............................................................................................................................................ 41

6.2.3 Bill of Materials ....................................................................................................................................... 47

6.3 CCG3 EVK Daughter Card .................................................................................................................................. 52

6.3.1 Schematics ............................................................................................................................................. 52

6.3.2 Gerber Files ............................................................................................................................................ 55

6.3.3 Bill of Materials ....................................................................................................................................... 61

Revision History ................................................................................................................................................................... 63

Document Revision History ........................................................................................................................................... 63

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 5

Safety Information

The CY4531 EZ-PD™ CCG3 EVK is intended for use as a development platform for hardware or software in a laboratory

environment. The board is an open-system design, which does not include a shielded enclosure. Due to this reason, the

board may cause interference to other electrical or electronic devices in close proximity. In a domestic environment, this

product may cause radio interference. In such cases, take adequate preventive measures. Also, do not use this board near

any medical equipment or RF devices.

Attaching additional wiring to this product or modifying the product operation from the factory default may affect its

performance and cause interference with other apparatus in the immediate vicinity. If such interference is detected, suitable

mitigating measures must be taken.

The CY4531 EZ-PD CCG3 EVK as shipped from the factory has been verified to meet with requirements of CE as a Class

A product.

The CY4531 EZ-PD CCG3 Evaluation Kit Guide boards contain ESD-sensitive devices.

Electrostatic charges readily accumulate on the human body and any equipment, which can cause

a discharge without detection. Permanent damage may occur to devices subjected to high-energy

discharges. Proper ESD precautions are recommended to avoid performance degradation or loss of

functionality. Store unused CY4531 EZ-PD CCG3 Evaluation Kit Guide boards in the protective

shipping package.

End-of-Life/Product Recycling

The end-of-life cycle for this kit is five years from the date of manufacture mentioned on the back of

the box. Contact the nearest recycler to discard the kit.

Safety Information

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 6

General Safety Instructions

ESD Protection

ESD can damage boards and associated components. Cypress recommends that the user perform procedures only at an

ESD workstation. If an ESD workstation is not available, use appropriate ESD protection by wearing an antistatic wrist strap

attached to the chassis ground (any unpainted metal surface) on the board when handling parts.

Handling Boards

The boards provided with CY4531 EZ-PD CCG3 Evaluation Kit are sensitive to ESD. This also applies to the boards that

are provided with a plastic casing when they are removed from the casing. Hold the boards only by the edges. After

removing a board from the box/casing, place it on a grounded, static-free surface. Use a conductive foam pad, if available.

Do not slide the board over any surface.

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 7

1. Introduction

The CY4531 EZ-PD™ CCG3 Evaluation Kit (EVK) is based on the CCG3 product family of Cypress’s USB Type-C

microcontrollers. This EVK is primarily intended to be an evaluation vehicle for USB Type-C host and client systems that

house a Type-C connector as well as for notebook applications. For USB Power Delivery (PD), the base board and

daughter card can be configured as a downstream facing port (DFP) or an upstream facing port (UFP). The kit also serves

as a vehicle to evaluate several features for Type-C, using a SuperSpeed USB demo and a DisplayPort demo, as

examples.

1.1 Kit Contents

The CY4531 EZ-PD CCG3 EVK consists of the following contents:

 CCG EVK Base Board

 CY4531 CCG3 Daughter Card (mounted on CCG EVK Base Board)

 24-V DC 65 W Power Adapter (24 V, 2.7 A)

 USB 3.0 Type-A to Type-B cable

 USB Type-C to Type-A adapter

 USB 3.1 EMCA (Electronically Marked Cable Assembly) Type-C cable

 USB 2.0 Type-A to Mini-B Cable

 Quick Start Guide

1.1.1 Hardware Not Included With Kit

The CY4531 EZ-PD CCG3 EVK does not come with all of the hardware needed to perform the demonstrations documented

in sections SuperSpeed USB Demo, DisplayPort Demo, and Dead Battery Demo of the Kit Operation chapter. The following

items are not included:

 USB flash drive needed for the SuperSpeed USB Demo section.

 DisplayPort cables needed for the DisplayPort Demo section. They are required to make connections from a PC to the

CCG EVK base board. If the PC has a mini-DisplayPort, then a mini-DisplayPort to DisplayPort cable will be required. If

the PC has a DisplayPort, then a DisplayPort to DisplayPort cable will be required. Recommended cables are listed in

Recommended Cables and Adapters section.

 USB Type-C to DP/HDMI/VGA adapter to connect a display monitor to the CY4531 EZ-PD CCG3 EVK. Recommended

adapters and cables needed for them to connect to monitors are listed in Recommended Cables and Adapters section.

 A digital multimeter to measure voltage for the Dead Battery Demo section. A standard multimeter is required to

measure the output voltage on the CCG base board to successfully demonstrate dead battery functionality along with a

USB Type-C Power Adapter.

Introduction

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 8

1.2 Getting Started

For instructions on how to run a quick demonstration and observe kit functionality, refer to the SuperSpeed USB Demo

section. This section also provides complete instructions on configuring the CY4531 EZ-PD CCG3 EVK base board and

daughter card.

1.3 List of Recommended Hardware

1.3.1 Recommended Cables and Adapters

See Table 1-1 to obtain a set of cables recommended to work with this kit. This kit is not shipped with these cables and

adapters and they are required to run the DisplayPort Demo and Dead Battery Demo.

Table 1-1. List of Recommended Cables and Adapters

No.

Description

Manufacturer

MPN

Vendor Link

1

DisplayPort to DisplayPort Cable (6”, gold plated)

Cable Matters

102005-6

Amazon Link

2

Mini DisplayPort to DisplayPort Cable (3”, gold plated)

Cable Matters

101007-BLACK-3

Amazon Link

3

Type-C to Display Port Adapter

Belinda

-

Amazon Link

4

Type-C to HDMI Adapter

Cable Matters

-

Amazon Link

5

Type-C to VGA Adapter

Cable Matters

-

Amazon Link

6

Type-C Power Adapter that supports 9V or above

Apple

-

Apple Store Link

Use item 1 or 2 in Table 1-1 to connect the PC’s DisplayPort or Mini-DisplayPort to the DisplayPort of CY4531 EZ-PD

CCG3 EVK. Depending on the display monitor you have, use item 3, 4 or 5 in Table 1-1 to connect from the USB Type-C

port of the CY4531 EZ-PD CCG3 EVK to the display monitor itself. Use item 6 to run the Dead Battery Demo.

1.4 Acronyms

Table 1-2. Acronyms Used in this Document

Acronym

Definition

ADC

analog-to-digital converter

CC

configuration channel

DFP

downstream facing port

DRP

dual role port

EC

embedded controller

EMCA

electronically marked cable assembly

EMI

electromagnetic interference

ESD

electrostatic discharge

EVK

evaluation kit

FET

field-effect transistor

GPIO

General-purpose input/output

HID

human interface device

HPD

hot plug detect

Introduction

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 9

Acronym

Definition

IC

integrated circuit

I2C

inter-integrated circuit

IDE

integrated development environment

LED

light-emitting diode

PSoC®

Programmable Systems-on-Chip

PWM

pulse-width modulation

QFN

quad flat no-lead (package)

SWD

serial wire debug

UART

universal asynchronous receiver transmitter

UFP

upstream facing port

USB

Universal Serial Bus

USB PD

Universal Serial Bus Power Delivery

XRES

External Reset I/O Pin

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 10

2. Kit Installation

This chapter describes how to perform the installation steps for the CY4531 EZ-PD CCG3 EVK.

2.1 CY4531 EZ-PD CCG3 EVK Kit Software Installation

To install the kit software, follow these steps:

a. Download the latest kit software setup file “CY4531 EZ-PD CCG3 EVK Complete Setup” from the kit’s website:

www.cypress.com/CY4531. This package contains the kit hardware files and the kit documentation (User Guide, Quick

Start Guide, and Release Notes). Double-click on the executable to start the installation. Click Next when the screen

shown in Figure 2-1 appears.

Figure 2-1. CY4531 EZ-PD CCG3 EVK Installer Screen

b. Select the required Installation Type and click Next to start the install (Figure 2-2). For first-time installation, it is

recommended that you select “Typical” as the Installation Type.

Kit Installation

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 11

Figure 2-2. Installation Wizard

c. Accept the license agreement for the software components and click Next (Figure 2-3).

Figure 2-3. License Agreement

Kit Installation

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 12

d. Figure 2-4 shows the installation progress.

Figure 2-4. Installation Progress

e. Click Finish when complete (Figure 2-5).

Figure 2-5. Software Installation Complete

Kit Installation

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 13

f. When installation is complete, you have the option to Launch Cypress Update Manager (Figure 2-6) to ensure you

have the latest software package. Click the Check for updates button at the bottom of the window. If “No Updates”

appears adjacent to the CY4531 EZ-PD CCG3 EVK, click the Exit button. If there are updates, click the Update button

to download and install the latest kit package.

Figure 2-6. Cypress Update Manager

Note: You can launch the Cypress Update Manager at any time from Start > All Programs > Cypress > Cypress

Update Manager.

g. After the installation is complete, the contents are available at the following location: <Install

Directory>\CY4531 CCG3 EVK\1.0.

Note: On the Windows 32-bit platform, the default <Install Directory> is C:\Program Files\Cypress; on the

Windows 64-bit platform, it is C:\Program Files(x86)\Cypress.

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 14

3. CY4531 EZ-PD CCG3 EVK Hardware

Details

The CY4531 EZ-PD CCG3 EVK consists of a base board and a daughter card. The CCG3 device is mounted on the

daughter card, which is connected to the base board to evaluate the CCG3 device’s Type-C port functionality as shown in

Figure 3-1.

Figure 3-1: CY4531 EZ-PD CCG3 EVK Architecture

PC

USB3

DP

USB2

CCG Base Board

CCG3

Daughter

Card

CCG3

DP1 Type-C

Port

SS USB

Type-B

Connector

Mux

with

Redriver

24 V dc

power

adapter

PS

USB-

Serial

CC

I2C

CY 4531 CCG3 EVK

Power

Display

Lines

USB

Lines

DP – DisplayPort

PS – Power Supply

USB2 – Used only for programming

The CCG base board consists of a DC input power supply, a Display multiplexer, one Display port, a SuperSpeed Type-B

port, and one Type-C port. The CCG3 daughter card consists of the CCG3 device and a USB-Serial IC to provide a USB

interface for debugging and programming. The CC lines of the CCG3 device are connected to the Type-C port. The Display

multiplexer is controlled by the CCG3 device over an I2C interface.

The CY4531 EZ-PD CCG3 EVK has a power provider and consumer path control circuitry to showcase EZ-PD CCG3’s

ability to switch its power role from a provider to a consumer and vice versa. This EVK has over-voltage and over-current

protection circuitry for VBUS and it also supports programming of the EZ-PD CCG3 device over SWD and I2C interfaces.

The EVK supports PCs, notebooks, tablets, and other applications that would host a Type-C interface. It is primarily

intended as an evaluation vehicle for USB host systems that house a Type-C connector.

CY4531 EZ-PD CCG3 EVK Hardware Details

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 15

3.1 CCG EVK Base Board

The CCG EVK base board is an evaluation board equipped with a Type-C port, a SuperSpeed USB Type-B port, and a

Display Port interface. It is primarily intended as a demonstration board for notebook designs that house a Type-C

connector. The board also serves as a vehicle to evaluate the alternate modes for Type-C, using the DisplayPort demo as

an example.

3.1.1 Block Diagram

The block diagram of the CCG EVK Base board is shown in Figure 3-2. It has an on-board Type-C connector for the USB-

PD interface and a CCG3 daughter card interface connector to connect the CCG3 daughter card. It also includes a

SuperSpeed USB Type-B port, and a Display Port connector to source video. The SuperSpeed USB signals and Display

Port signals are connected to the Type-C connector through a high-speed multiplexer controlled by the CCG3 device. A DC

power adapter provides input voltage to the onboard Power Management IC (PMIC). The output voltage from the PMIC can

be selected using two voltage selection lines, controlled by the CCG3 device. This CCG base board along with the CCG3

daughter card helps to convert any desktop or notebook PC with legacy USB ports to operate as a Type-C USB host.

Figure 3-2: CCG EVK Base Board Block Diagram

Power

Input

Header

Data MUX

Type-C Receptacle

PMIC

USB

Super

Speed Port

Display

Port

CC

from

CCG3

Data

Lanes

(Tx/Rx)

Control from

CCG3

D+/D-

4

8

2

AUX Lines

2

USB SuperSpeed

Lines

DisplayPort

Lines

Hot Plug Detect

(HPD)

Voltage Selection

lines from

CCG3

VBUS

DC

Power

Jack

VBUS

Provider

Control

VBUS

Consumer

Control

Power

Output

Header

2

3.1.2 Features

Table 3-1 shows the features of the CCG EVK base board.

Table 3-1: CCG EVK Base Board Features

Feature

Description

Power

Negotiated power from the DC power adapter controlled by PMIC and CCG3. 5 V from the Type-C

connector (for dead battery support).

Note: The DC power adapter provided with the kit can support only up to 2.7A (at 24 V). This kit will

not work with 5-V DC power adapters.

CCG3 Daughter Card Interface

Connector

Provides interface to connect the CCG3 daughter card to the CCG EVK base board

Type-C Plug orientation,

Detection and Alternate modes

I2C interface between the CCG3 device and a display multiplexer to select between SuperSpeed USB

and 2-lane/4-lane DisplayPort

Hot Plug Detect (HPD) for Display Port Alternate Mode of operation

CY4531 EZ-PD CCG3 EVK Hardware Details

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 16

3.1.3 Connectors and Jumper Settings

Figure 3-3 shows the CCG EVK base board connectors and default settings of the jumpers. Table 3-2 contains the detailed

description of the connectors and jumper settings.

Figure 3-3: CCG EVK Base Board Connectors

Table 3-2: CCG EVK Base Board Connector/Jumper Description

Connector/Jumper

Description

Default

J1

DC power jack to connect the DC power adapter to the CCG base board

NA

J2

SuperSpeed USB Type-B connector (receptacle)

NA

J3

USB Type-C Connector (receptacle)

NA

J4

DisplayPort Connector

NA

J5

USB 2.0 Mini-B Connector (Receptacle)

NA

J6

USB Serial Debug Header

This connector is

not populated

J7

Header for voltage measurement when CCG3 acts as a power consumer or power output header

NA

J8

CCG3 Daughter Card Interface Connector

NA

Pin 1,2: Regulated input power from 24-VDC terminal (J12) of CCG EVK Base Board

(USB_P_PWR)

J4

DisplayPort

Connector

J2

SuperSpeed

USB Type-B

Connector

J7

Consumer

Power Output

Header

J9

Debug

Connector

J8

CCG3 Daughter

Card Interface

Connector

J3

USB Type-C

Receptacle

J1 DC Power

Supply

Connector

J12 Variable

Power Supply

(Provider)

Header

J5

USB 2.0

Mini-B

Connector

LED1

(Green)

LED2 (Orange)

J11

User LED

Connector

CY4531 EZ-PD CCG3 EVK Hardware Details

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 17

Connector/Jumper

Description

Default

Pin 3,4: Power from VBUS of Type-C Connector (Type-C_VBUS)

Pin 5,6: Regulated output power to 20-Vdc terminal (J7) from USB_C_PWR pin of CCG3

daughter card

Pin 7: GND

Pin 8: GND

Pin 9: I2C_SCL

Pin 10: VBUS_DISCHRG

Pin 11: I2C_SDA

Pin 12: CCGx SWDIO

Pin 13: Over Current Protection Pin

Pin 14: CCGx SWD_CLK

Pin 15: AC_Adapter_Detect

Pin 16: CCGx XRES

Pin 17: VSEL2

Pin 18: I2C_ADDR0

Pin 19: 5 V

Pin 20: VCONN Monitor

Pin 21: CC1

Pin 22: CC2

Pin 23: 3.3 V

Pin 24: VBUS_P_CTRL

Pin 25: RXD

Pin 26: VBUS Monitor

Pin 27: TXD

Pin 28: I2C_INT_EC

Pin 29: MUX_DP_AUXN

Pin 30: VBUS_C_CTRL

Pin 31: MUX_DP_AUXP

Pin 32: Over Voltage Protection Pin

Pin 33: SBU2

Pin 34: I2C_SDA_EC

Pin 35: SBU1

Pin 36: Hotplug Detect

Pin 37: I2C_SCL_EC

Pin 38: TP12

Pin 39: VSEL1

Pin 40: TP11

J9

Debug Connector

NA

Pin 1,2: Power from VBUS of Type-C Connector (Type-C_VBUS)

Pin 3: CCGx SWDIO

Pin 4: CCGx XRES

Pin 5: CCGx CC1

Pin 6: CCGx CC2

Pin 7: I2C_SCL_EC

Pin 8: I2C_SDA_EC

Pin 9: I2C_INT_EC

Pin 10: Hotplug Detect

Pin 11: I2C_SCL

Pin 12: SW1/I2C_SDA

Pin 13: SW2

Pin 14: Over Current Protection Pin

Pin 15: CCGx SWD_CLK

Pin 16: Over Voltage Protection Pin

Pin 17: VSEL1

Pin 18: VSEL2

Pin 19: VBUS_P_CTRL

Pin 20: VBUS_DISCHRG

Pin 21: VBUS_Monitor GPIO

Pin 22: VBUS_C_CTRL

Pin 23: GND

Pin 24: GND

J10

I2C Connector

This connector is

not populated

Pin 1: I2C_SDA_EC

Pin 2: I2C_SCL_EC

Pin 3: I2C_INT_EC

Pin 4: GND

J11

User LED jumper for connecting LED to GPIO

Pin 1: SWD_IO

Pin 2: LED

Shorted

J12

Header for voltage measurement when CCG3 acts as a power provider or power input header.

NA

CY4531 EZ-PD CCG3 EVK Hardware Details

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 18

3.2 CY4531 CCG3 Daughter Card

The CCG3 daughter card is equipped with the CYPD3125-40LQXIT of the CCG3 device family and a CY7C65215-32LTXI

USB-Serial Bridge Controller to provide a USB interface for debugging and programming. This CCG3 daughter card, when

assembled with the CCG base board supports Type-C host applications such as note books and tablets.

3.2.1 Block Diagram

Figure 3-4 shows the CCG3 daughter card block diagram.

Figure 3-4 CCG3 Daughter Card Block Diagram

USB-Serial

Device

USB2.0 Mini

Port

VBUS

I2C

D+/D-

Power

Consumer

Control

Circuitry

Power

Provider

Control

Circuitry VBUS to

Type- C Port1

VBUS_P_CTRL_P1 VBUS_C_CTRL_P1

2

2CC_P1 to Type-C Port1

2AUX_P1 to SBU MUX1

CCG3

Device

I2C_INTR

3.2.2 Features

Table 3-3 lists the features of the CCG3 daughter card.

Table 3-3: CCG3 Daughter Card Features

Feature

Description

CCG3 part number

CYPD3125-40LQXIT

CCG3 package

40-pin QFN

USB PD/ Type-C

Ability to support DRP, DFP, and UFP

Type-C VBUS current setting via a jumper that selects one of the three Rp values. These three values

correspond to the three currents as defined in the Type-C specification.

VBUS provider field-effect transistor (FET) control for cold socket

VBUS consumer FET control

VBUS discharge FET control

Ability to present either Rd or Rp on CC line

Dead battery support

OVP and OCP

VCONN or VBUS over-current protection

VBUS over-voltage protection

Plug orientation, Detection and

Alternate modes

Five MUX-select pins to select between SuperSpeed USB and 2-lane or 4-lane DisplayPort

Hot Plug Detect (HPD) for DisplayPort Alternate Mode of operation

USB 2.0 Type-B Mini

USB 2.0 Mini-B receptacle connected to USB-to-Serial device

I2C interface

I2C pins and interrupt output pin for connecting to an Embedded Controller (EC)

Programming

SWD pins to debug/program CCG3 using Cypress MiniProg3

CY4531 EZ-PD CCG3 EVK Hardware Details

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 19

Feature

Description

Power

5 V from USB 2.0 Mini (Connector J7 of CCG3 daughter card)

5 V from MiniProg3 (Connector J1 of CCG3 daughter card)

5 V to 20 V from Type-C connector (Connector J3 of CCG base board)

24V DC from DC Power Supply Connector (Connector J1 of CCG base board)

3.2.3 Connectors and Jumper Settings

Figure 3-5 shows the CCG3 daughter card connectors and default settings of the jumpers. Table 3-4 contains the detailed

description of the connectors and jumper settings.

Figure 3-5: CCG3 Daughter Card Connectors/Jumper Settings

Table 3-4: CCG3 Daughter Card Connector/Jumper Description

Connector/Jumper

Description

Default

J1

Programming header

Pin 1: VTARG

Pin 2: GND

Pin3: CCG3_XRES

Pin4: CCG3_SWD_CLK

Pin5: CCG3_SWD_IO

NA

J2

Debug header connected to gate driver pins of the CCG3 device

This connector is

J1

Programming Header

J3: VSYS Selection Jumper

1-2 Short: 3.3V supply

coming from CCG base

board (Default Setting)

2-3 Short: Power from 5 V

buck regulator of CCG base

board

J6

CCG Base Board

Interface Connector

J7

USB 2.0 Mini-B

Receptacle

J4: IO Supply Selection

Jumper

1-2 Short: Power from

VSYS of CCG3

2-3 Short: Power from

VDDD of CCG3 (Default

Setting)

SW1

Reset Switch

CY4531 EZ-PD CCG3 EVK Hardware Details

CY4531 EZ-PD™ CCG3 Evaluation Kit Guide, Doc. No. 002-10218 Rev. *B 20

Connector/Jumper

Description

Default

Pin 1: NC

Pin 2: VBUS_P_CTRL1

not populated

Pin 3: VBUS_C_CTRL1

Pin 4: GND

J3

VSYS selection jumper:

1 and 2 short: Select the power from 3.3-V supply coming from the CCG base board

2 and 3 short: Select the power from 5-V buck regulator of the CCG base board

1 and 2 short

J4

I/O supply selection jumper:

1 and 2 short: Select the power from VSYS of CCG3 device

2 and 3 short: Select the power from VDDD of CCG3 device

2 and 3 short

J5

Spare 40-pin connector

This connector is

not populated

J6

CCGx Base Board Interface Connector

NA

Pin 1,2: Regulated input power from 24-VDC terminal (J12) of the CCG EVK Base Board

(USB_P_PWR_P1)

Pin 3,4: Power from VBUS of Type-C Connector of the CCG EVK Base Board (TYPE-

C_VBUS_P1)

Pin 5,6: Regulated output power to 20-VDC terminal (J7) of the CCG EVK Base Board

(USB_C_PWR_P1)

Pin 7: GND

Pin 8: GND

Pin 9: I2C_SCL

Pin 10: VBUS_DISCHRG_P1

Pin 11: I2C_SDA

Pin 12: SWDIO

Pin 13: USB Provider Power Sense Pin

Pin 14: SWD_CLK

Pin 15: AC_Adaptor_Detect

Pin 16: XRES

Pin 17: VSEL2

Pin 18: UART2_RX

Pin 19: 5 V

Pin 20: UART2_TX

Pin 21: CC1

Pin 22: CC2

Pin 23: 3.3 V

Pin 24: VBUS_P_CTRL0

Pin 25: TXD

Pin 26: VCONN

Pin 27: RXD

Pin 28: I2C_INT_EC

Pin 29: DP_AUXN_P1

Pin 30: VBUS_C_CTRL0

Pin 31: DP_AUXP_P1

Pin 32: GPIO/P2.4

Pin 33: SBU2

Pin 34: I2C_SDA_EC

Pin 35: SBU1

Pin 36: Hotplug Detect

Pin 37: I2C_SCL_EC

Pin 38: DPlus

Pin 39: VSEL1

Pin 40: DMinus

J7

USB 2.0 Mini-B connector (receptacle)

Connected to USB-Serial device and used for programming CCG3 device

NA

3.3 Powering the CY4531 EZ-PD CCG3 EVK Setup

The CY4531 EZ-PD CCG3 EVK can be powered by connecting the 24-V DC power adapter to connector J1 of the CCG

EVK base board. LED1 on both the boards glow green and LED2 on the base board blinks orange continuously, to indicate

a successful power connection. The CY4531 EZ-PD CCG3 EVK can also be powered by connecting 24-V DC from a

variable power supply to the terminals of connector J12 of the CCG base board.

Note: Check the jumper positions before you power the board. See Figure 3-3 and Figure 3-5 for default jumper settings of

the CCG EVK base board and CCG3 daughter card.

Page is loading ...

Cypress CY4531 User manual

This manual is also suitable for

Cypress CY4531 User manual

Related papers

Other documents