SMC Networks SMC10GPCIE-10BT User manual

Brand: SMC Networks

Model: SMC10GPCIE-10BT

Category: Networking cards

Type: User manual

This manual is also suitable for

USER GUIDE

TigerCard

10G

10GBASE-T and XFP

Ethernet Server Adapters

SMC10GPCIe-10BT

SMC10GPCIe-XFP

20 Mason

Irvine, CA 92618

Phone: (949) 679-8000

TigerCard 10G

User Guide

From SMC’s Tiger line of feature-rich workgroup LAN solutions

June 2008

Pub. # SFMMANUAL-0002

E062008-CS-R02

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and

reliable. However, no responsibility is assumed by SMC for its use, nor for any

infringements of patents or other rights of third parties which may result from its use. No

license is granted by implication or otherwise under any patent or patent rights of SMC.

SMC reserves the right to change specifications at any time without notice.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

Trademarks:

SMC is a registered trademark; and EZ Switch, TigerCard, TigerStack and TigerSwitch

are trademarks of SMC Networks, Inc. Other product and company names are

trademarks or registered trademarks of their respective holders.

Limited Warranty

Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be

free from defects in workmanship and materials, under normal use and service, for the

applicable warranty term. All SMC products carry a standard 90-day limited warranty from

the date of purchase from SMC or its Authorized Reseller. SMC may, at its own discretion,

repair or replace any product not operating as warranted with a similar or functionally

equivalent product, during the applicable warranty term. SMC will endeavor to repair or

replace any product returned under warranty within 30 days of receipt of the product.

The standard limited warranty can be upgraded to a Limited Lifetime* warranty by

registering new products within 30 days of purchase from SMC or its Authorized Reseller.

Registration can be accomplished via the enclosed product registration card or online via

the SMC Web site. Failure to register will not affect the standard limited warranty. The

Limited Lifetime warranty covers a product during the Life of that Product, which is

defined as the period of time during which the product is an “Active” SMC product. A

product is considered to be “Active” while it is listed on the current SMC price list. As new

technologies emerge, older technologies become obsolete and SMC will, at its discretion,

replace an older product in its product line with one that incorporates these newer

technologies. At that point, the obsolete product is discontinued and is no longer an

“Active” SMC product. A list of discontinued products with their respective dates of

discontinuance can be found at: http://www.smc.com/smc/pages_html/support.html.

All products that are replaced become the property of SMC. Replacement products may

be either new or reconditioned. Any replaced or repaired product carries either a 30-day

limited warranty or the remainder of the initial warranty, whichever is longer. SMC is not

responsible for any custom software or firmware, configuration information, or memory

data of Customer contained in, stored on, or integrated with any products returned to

SMC pursuant to any warranty. Products returned to SMC should have any

customer-installed accessory or add-on components, such as expansion modules,

removed prior to returning the product for replacement. SMC is not responsible for these

items if they are returned with the product.

Customers must contact SMC for a Return Material Authorization number prior to

returning any product to SMC. Proof of purchase may be required. Any product returned

to SMC without a valid Return Material Authorization (RMA) number clearly marked on

the outside of the package will be returned to customer at customer’s expense. For

warranty claims within North America, please call our toll-free customer support number

at (800) 762-4968. Customers are responsible for all shipping charges from their facility to

SMC. SMC is responsible for return shipping charges from SMC to customer.

WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR

REPLACEMENT OF THE PRODUCT IN QUESTION, AT SMC’S OPTION. THE

FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF

ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, EITHER IN

FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. SMC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER

PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE

SALE, INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS. SMC SHALL

NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION

DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS

CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT,

IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR,

OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY

ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: IN NO EVENT, WHETHER BASED IN CONTRACT OR

TORT (INCLUDING NEGLIGENCE), SHALL SMC BE LIABLE FOR INCIDENTAL,

CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR

FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS

ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS

PRODUCTS, EVEN IF SMC OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES OR

THE LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR

CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS AND EXCLUSIONS MAY

NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,

WHICH MAY VARY FROM STATE TO STATE. NOTHING IN THIS WARRANTY SHALL

BE TAKEN TO AFFECT YOUR STATUTORY RIGHTS.

* SMC will provide warranty service for one year following discontinuance from the active

SMC price list. Under the limited lifetime warranty, internal and external power supplies,

fans, and cables are covered by a standard one-year warranty from date of purchase.

SMC Networks, Inc.

20 Mason

Irvine, CA 92618

Compliances

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

You are cautioned that changes or modifications not expressly approved by the party

responsible for compliance could void your authority to operate the equipment.

You may use Category 5e or better twisted-pair for 10 Gbps RJ-45 connections. For fiber

optic connections, you may use 50/125 or 62.5/125 micron multimode fiber or 9/125

micron single-mode fiber.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

CE Mark Conformance Declaration - Class A

SMC contact for these products in Europe is:

SMC Networks Europe,

Edificio Conata II,

Calle Fructuós Gelabert 6-8, 2

, 4

08970 - Sant Joan Despí, Barcelona, Spain.

This information technology equipment complies with the requirements of the Council

Directive 89/336/EEC on the Approximation of the laws of the Member States relating to

Electromagnetic Compatibility and 73/23/EEC for electrical equipment used within certain

voltage limits and the Amendment Directive 93/68/EEC. For the evaluation of the

compliance with these Directives, the following standards were applied:

RFI Emission: Limit class A according to EN 55022:1998

Limit class A for harmonic current emission according to EN 61000-3-2/

1995

Limitation of voltage fluctuation and flicker in low-voltage supply system

according to EN 61000-3-3/1995

Immunity: Product family standard according to EN 55024:1998

Electrostatic Discharge according to EN 61000-4-2:1995

(Contact Discharge: ±4 kV, Air Discharge: ±8 kV)

Radio-frequency electromagnetic field according to EN 61000-4-3:1996

(80 - 1000 MHz with 1 kHz AM 80% Modulation: 3 V/m)

Electrical fast transient/burst according to EN 61000-4-4:1995

(AC/DC power supply: ±1 kV, Data/Signal lines: ±0.5 kV)

Surge immunity test according to EN 61000-4-5:1995

(AC/DC Line to Line: ±1 kV, AC/DC Line to Earth: ±2 kV)

Immunity to conducted disturbances, Induced by radio-frequency fields:

EN 61000-4-6:1996 (0.15 - 80 MHz with 1 kHz AM 80% Modulation:

3V/m)

Power frequency magnetic field immunity test according to

EN 61000-4-8:1993 (1 A/m at frequency 50 Hz)

Voltage dips, short interruptions and voltage variations immunity test

according to EN 61000-4-11:1994 (>95% Reduction @10 ms, 30%

Reduction @500 ms, >95% Reduction @5000 ms)

iii

About This Guide

Purpose

This guide details of the hardware features of the Ethernet adapter card, including its

physical and performance-related characteristics, and how to install the card.

Audience

The guide is intended for use by system administrators who are responsible for installing

and setting up computer network equipment; consequently, it assumes a basic working

knowledge of PC operating systems and LANs (Local Area Networks).

Conventions

The following conventions are used throughout this guide to show information:

Note: Emphasizes important information or calls your attention to related features or

instructions.

Caution: Alerts you to a potential hazard that could cause loss of data, or damage the

system or equipment.

Warning: Alerts you to a potential hazard that could cause personal injury.

Related Publications

The following publication gives basic information on how to install and use the Ethernet

adapter card.

Quick Installation Guide

Revision History

This section summarizes the changes in each revision of this guide.

June 2008 Revision

This is the second revision of this guide. It includes the following changes:

• Added iSCSI support.

• Added MSI-X support.

• Added Receive Side Scaling (RSS) support.

• Updated Microsoft Windows Server® installation.

• Updated Linux installation.

January 2008 Revision

This was the first revision of this guide.

Contents

Chapter 1: Introduction 1-1

Advanced Features 1-1

Hardware Description 1-3

LED Indicators 1-4

Equipment Checklist 1-5

Chapter 2: Hardware Installation 2-1

Chapter 3: Driver Installation 3-1

Windows Driver Installation 3-1

Linux Installation Instructions 3-6

Installation From a Binary RPM 3-6

RedHat Enterprise Linux Distributions 3-7

SuSE Linux Enterprise Server distributions 3-7

Building the Source RPM 3-8

Appendix A: Troubleshooting A-1

PCI Express Bus Width A-1

Common Installation Problems A-1

Network Connection Problems A-2

Appendix B: Cable Types B-1

UTP Cables B-1

Fiber Cables B-1

Appendix C: Specifications C-1

Glossary

1-1

Chapter 1: Introduction

The SMC TigerCard™ 10G 10GBASE-T and XFP Ethernet Server Adapters

combine the speed and performance of cutting edge networking with the ease of

deployment and user friendliness of traditional Ethernet. The speed and efficiency of

10G networking coupled with iSCSI support enables converged networking,

reducing cost and the complexity of wiring, and simplifying management. SMC’s

VNIC architecture provides the key to efficient server I/O and is flexible enough to be

applied to multiple server deployment scenarios. These deployment scenarios are:

• Kernel Driver – This deployment uses a single instance of a VNIC interface for

standard operating drivers. This interface provides a performance-optimized path

for the kernel TCP/IP stack and contention-free access from the driver, resulting in

extremely low latency and competitive CPU efficiency.

• Accelerated Virtual I/O – The second deployment scenario greatly improves I/O

for virtualized operating systems. The SMC VNIC architecture provides thousands

of protected interfaces to the host system, granting any application or virtualized

(guest) operating system direct access to the network hardware. This hypervisor

bypass technology, unique to SMC Ethernet controllers, is the only way to provide

solid I/O performance to virtualized guest operating systems.

Advanced Features

• Virtual NIC Support – The core of SMC’s technology. Protected VNIC interfaces

can be instantiated for each running guest operating system or application, giving

it a direct pipeline to the Ethernet network. This architecture provides the most

efficient way to maximize network and CPU efficiency. The SMC Ethernet

controller supports up to 4096 VNIC interfaces.

• PCI Express – Implements PCI Express 1.1.

• Plug-and-Play – Provides binary compatibility with all data center and HPC

applications.

• 10 Gigabit Ethernet – 10 times the throughput of 1G Ethernet, 10G enables the

ability to design a cost-effective, high-performance 10 Gigabit Ethernet solution.

• iSCSI Support – Reduced TCO (total cost of ownership) for shared storage and

converged fabrics.

• iSCSI Acceleration in Virtual Environment – Reduce CPU utilization, lower

networking latency, improved machine utilization, and easier management.

• RSS – Receive Side Scaling raises the utilization levels of multi-core servers

dramatically by distributing I/O load across all CPUs and cores.

Advanced Features

1-2

• IP/UDP/TCP Checksum Offload – Calculation and validation for the checksums

found in IP, TCP and UDP headers. This feature saves a significant amount of

valuable CPU cycles.

• Transmit Rate Pacing (per queue) – Provides a mechanism for enforcing

bandwidth quotas across all guest operating systems. Software re-programmable

on-the-fly to allow for adjustment as congestion increases on the network.

• Jumbo Frame Rate (9K) – Smaller per packet overhead, increased network

utilization.

• MSI and MSI-X – Both MSI and MSI-X support enable higher levels of performance

on both legacy and up-to-date systems.

• Remote Boot – Support for Etherboot, PXE boot, and Linux® BIOS provides

flexibility in cluster design and diskless servers. A small programmable on-board

ROM contains the boot code that provides this functionality.

• IP Flow Filtering – Enables the hardware to steer packets based on IP, TCP, and

UDP header contents.

Hardware Description

1-3

Hardware Description

SMC TigerCard™ 10G 10GBASE-T Ethernet Server Adapter comes equipped with:

• One RJ-45 connector for 10 Gbps connections

• Three LED indicators

The components of the SMC TigerCard™ 10G 10GBASE-T Ethernet Server

Adapter are shown in the figure below.

Note: A Low-Profile bracket is also inlcluded.

Hardware Description

1-4

The SMC TigerCard™ 10G 10GBASE-XFP Ethernet Server Adapter comes

equipped with:

• One XFP slot for 10 Gbps XFP transceivers (SR or LR)

• Three LED indicators

The components of the SMC TigerCard™ 10G 10GBASE-XFP Ethernet Server

Adapter are shown in the figure below.

Note: Shown with an XFP transceiver (not included).

LED Indicators

The following table describes the TigerCard™ 10G states reported by the LEDs.

LED Condition Status

Red

(Error Checking)

Off No fault.

On Fault.

Green

(Link)

Off There is no valid link on the port.

On The card has established a valid network

connection.

Flashing SMC10GPCIe-10BT: Obtaining a link.

SMC10GPCIe-XFP: Receiving.

Amber

(Activity)

Off There is no valid link on the port.

On The network connection is operating at 10 Gbps.

Flashing SMC10GPCIe-10BT: Receiving or transmitting.

SMC10GPCIe-XFP: Transmitting.

Equipment Checklist

1-5

Equipment Checklist

After unpacking the TigerCard™ 10G Ethernet Server Adapter, check the contents

of the box to be sure you have received the following items:

• SMC TigerCard™ 10G, SMC10GPCIe-10BT or SMC10GPCIe-XFP

• Driver and Documentation CD

• SMC Warranty Registration Card

• Low-Profile Bracket

Immediately inform your dealer in the event of any incorrect, missing or damaged

parts. If possible, please retain the carton and original packing materials in case

there is a need to return the product.

Please register this product online at SMC’s web site, http://www.smc.com/. The

SMC TigerCard™ 10G is covered by a limited lifetime warranty.

2-1

Chapter 2: Hardware Installation

Caution: Network cards are sensitive to static electricity. To protect the card, avoid

touching its electrical components and always touch the metal chassis of

your computer before handling the card.

1. Switch off the computer, unplug the power cord, and remove the computer’s

cover.

2. Select an unused PCI Express (PCIe) bus-master slot and remove its

protective bracket.

3. Carefully insert the card and press until all the edge connectors are firmly

seated inside the slot. Then screw the card’s bracket securely into the PC’s

chassis.

4. Connect the TigerCard™ 10G directly to a network switch.

a. For the 10GBASE-T card, use UTP cable (use appropriate 10GBASE-T

cable; see “UTP Cables” on page B-1). The maximum allowable length of

UTP cable connections is 100 meters (328 ft). When inserting an RJ-45

plug, be sure the tab on the plug clicks into position to ensure that it is

properly seated.

b. For the XFP card, use 9/125 micron single-mode fiber cable, or 50/125 or

62.5/125 micron multimode fiber cable, depending on the XFP transceiver

installed (10GBASE-SR or 10GBASE-LR). For more information, see

“Fiber Cables” on page B-1.

2-2

5. Replace the computer’s cover and power it on. The TigerCard™ 10G should be

automatically configured by the host computer’s BIOS. However, if you have an

older computer, you may have to manually configure the computer’s BIOS

settings. See “Troubleshooting” on page A-1.”

Once hardware installation is complete, see Chaper 3 “Driver Installation” for

information on installing the appropriate driver for your operating system.

3-1

Chapter 3: Driver Installation

The Driver and Documentation CD that accompanies the TigerCard™ 10G contains

all the operating system drivers supported by this card. See the “RELEASE.TXT” file

on the CD for a list of all drivers. Refer to this guide for instructions on installing

drivers.

Any new or updated drivers can be downloaded from SMC’s Web site,

http://www.smc.com/.

Note: The install procedures in this guide show how to install the

SMC10GPCIe-10BT drivers. The install procedures for the

SMC10GPCIe-XFP drivers are identical.

Windows Driver Installation

Download the following package from the SMC support site:

SMC10GPCIe-10BT: Windows Driver Package

This package contains a Microsoft Windows® Installer (MSI) Setup Wizard for the

Windows drivers.

You will need local administrative privileges on the target machine in order to install

the SMC network drivers. If you do not have administrative privileges on the target

machine, contact your system administrator for assistance.

Driver installation can be performed before or after installing the TigerCard™ 10G

into the target machine. However, SMC recommends users install the

TigerCard™ 10G into the target machine before installing the SMC drivers. The

SMC Setup Wizard can install drivers automatically without requiring you to

manually follow the steps of the “Found New Hardware Wizard.”

1. On the first boot after installing the TigerCard™ 10G into the target machine,

Windows may prompt you with the “Found New Hardware” dialog. Click

"Cancel."

If the “Found New Hardware” dialog appears later during the installation

process, it can be safely ignored.

Windows Driver Installation

3-2

Microsoft Windows Server® 2008:

Microsoft Windows Server® 2003:

2. Double click on the MSI installation file.

Windows Driver Installation

3-3

After a brief pause the Setup Wizard is displayed. Click “Next” to continue with

the installation.

3. The software end-user license agreement is displayed. To install the drivers,

you must indicate you accept this agreement and click “Next.”

Windows Driver Installation

3-4

4. Select the destination folder for the driver package and click “Next.”

5. No further configuration of the installation process is necessary. Click “Install” to

begin the driver installation.

6. The driver installation process can take a few minutes. The Setup Wizard

displays its status and progress during this period.

Page is loading ...

SMC Networks SMC10GPCIE-10BT User manual

Brand: SMC Networks

Model: SMC10GPCIE-10BT

Category: Networking cards

Type: User manual

This manual is also suitable for

Download PDF

report

SMC Networks SMC10GPCIE-10BT User manual

This manual is also suitable for

SMC Networks SMC10GPCIE-10BT User manual

Related papers

Other documents