JVC HV-28D40BK User manual

Brand: JVC

Model: HV-28D40BK

Category: LCD TVs

Type: User manual

This manual is also suitable for

HV-32/28D40BK / LCT1596-001A-U / All Cover

Cover01

Integrated Digital Colour Television

INSTRUCTIONS

HV-32D40BK

HV-28D40BK

Trade Mark of the DVB Digital Video Broadcasting

Project (1991 to 1996) Number: 3081

LCT1596-001A-U_Cover.fm Page 1 Friday, April 23, 2004 11:19 AM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH



Warning

DO NOT cut off the mains plug from this

equipment.

If the plug fitted is not suitable

for the power points in your home or the cable

is too short to reach a power point, then obtain

an appropriate safety approved extension lead

or adaptor or consult your dealer.

If nonetheless the mains plug is cut off,

remove the fuse and dispose of the plug

immediately, to avoid a possible shock

hazard by inadvertent connection to the

mains supply.

If a new mains plug has to be fitted, then

follow the instruction given below:

Important

Do not make any connection to the larger

terminal which is marked with the letter E or

by the safety earth symbol or coloured

green or green-and-yellow.

The wires in the mains lead on this product

are coloured in accordance with the

following code:

Blue: Neutral

Brown: Live

As these colours may not correspond with the

coloured marking identifying the terminals in

your plug proceed as follows:

The wire which is coloured blue must be

connected to the terminal which is marked

with the letter N or coloured black.

The wire which is coloured brown must be

connected to the terminal which is marked

with the letter L or coloured red.

When replacing the fuse, use only a correctly

rated approved type and always re-fit the fuse

cover.

 If in doubt — consult a competent

electrician.

How to replace the fuse

Open the fuse

compartment with a

blade screwdriver, and

replace the fuse.



Guidelines for safe operation

This equipment has been designed and manufactured to comply with international safety

standards. However, as with any electrical appliance, care must be taken to ensure optimal results

and operational safety.

• Before attempting to use this equipment, read the operating instructions thoroughly.

• Ensure that all electrical connections (including the mains plug, extension leads, etc.) have

been made in accordance with the manufacturer’s instructions.

• If ever in doubt about the installation, operation or safety of this equipment, consult your dealer.

• Handle all glass panels or covers with care.

• Never operate this equipment if it appears damaged or operates abnormally. Turn the power

off, disconnect the main power plug and consult your dealer.

• Never remove any affixed panels or covers. Doing so may result in electrical shock.

• Never leave this equipment operating unattended unless otherwise specifically stated that it is

designed to do so or in standby mode. Only use the designated power switch to turn off the

power and ensure that all potential users are instructed how to do so. Make special

arrangements for infirm or handicapped persons.

• Never watch TV while operating a motor vehicle. It is illegal to watch TV while driving.

• Never listen to headphones at high volume. Doing so may damage your hearing.

• Never obstruct the ventilation of this equipment. Doing so may cause overheating and result in

a malfunction or damage.

• Never use makeshift stands or attempt to affix legs with wood screws. When using a

manufacturer’s approved stand or legs, use only the fixtures provided and follow the

installation instructions.

• Never allow this equipment to be exposed to rain or moisture.

• Never allow anyone, especially children, to insert anything into an opening in the case. Doing

so may result in a fatal electrical shock.

• Never guess or take chances with electrical equipment of any kind. It is better to be safe than sorry.

Fuse

HV-32&28D40BK_Eng.book Page 2 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

How to move the TV

When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful

not to trap your hands when putting the TV down.

HV-32&28D40BK_Eng.book Page 3 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Thank you for buying this JVC colour television.

To make sure you understand how to use your new TV, please read this manual thoroughly before you

begin.

Avoid improper installation and never put the unit where good

ventilation is not possible.

When installing this TV, distance recommendations must be

maintained between the set and the wall, as well as inside a tightly

enclosed area or piece of furniture.

Adhere to the minimum distance guidelines shown for safe operation.

Failure to heed the following precautions may result in damage to the TV or

remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be

able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• When you are not using this unit for a long

period of time, it is recommended that you

disconnect the power cord from the main

outlet.

• The main power button on the TV does not

fully isolate the TV from the mains supply. If

you are not going to use this TV for a long

period of time, be sure to disconnect the mains

plug from the mains outlet.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.

Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully.

Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it

yourself or remove the rear cover.

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:

Press the H button to display the menu bar. Then press the yellow button.

A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.

To quit the D.I.S.T. demonstration:

Press the yellow button,

TV/DTV button, p p buttons or any of the number buttons.

NOTE:

Due to static electricity, the TV may be covered with dust.

If this happens, wipe the TV with a soft cloth being careful not to scratch the TV.

HV-32&28D40BK_Eng.book Page 4 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Digital terrestrial broadcasting (DVB-T) service area

Although this TV can receive both Digital terrestrial broadcasting (DVB-T) and Analogue terrestrial

broadcasting, depending on the area in which you live, you may not be able to receive Digital

terrestrial broadcasting (DVB-T).

For details of the Digital terrestrial broadcasting (DVB-T) service area, refer to the FREEVIEW

website etc.

HV-32&28D40BK_Eng.book Page 5 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

CONTENTS

Setting up your TV ...................................7

Connecting the aerial................................. 7

Connecting the power cord to the AC

outlet....................................................... 8

Putting the batteries into the remote

control..................................................... 8

Initial settings ............................................. 8

T-V LINK functions................................... 11

TV buttons and functions......................13

Turn the main power on ........................... 13

Turn the TV on from standby mode ......... 13

Choose a TV channel .............................. 13

Adjust the volume .................................... 14

Remote control buttons and

functions..............................................15

Turn the TV on or off from standby mode

... 15

Choose a TV channel and watch images

from external devices ........................... 16

Adjust the volume .................................... 17

Information function ................................. 17

ZOOM function......................................... 18

3D CINEMA SOUND function.................. 20

Using the FREEZE function ..................... 20

Using the MULTI-PICTURE function ....... 20

Using the GUIDE ..................................... 22

Displaying the Subtitles............................ 24

Operating a JVC brand VCR or DVD

player.................................................... 24

Teletext function ....................................25

Basic operation (Digital)........................... 25

Basic operation (Analogue)...................... 26

Using the List Mode ................................. 26

Hold.......................................................... 27

Sub-page ................................................. 27

Reveal...................................................... 27

Size .......................................................... 27

Index ........................................................ 27

Cancel...................................................... 27

Using the TV’s menu..............................28

Basic operation ........................................ 28

PICTURE menu ...................................... 29

PICTURE MODE...................................... 29

CONTRAST ............................................. 29

BRIGHT.................................................... 29

SHARP..................................................... 29

COLOUR.................................................. 29

HUE.......................................................... 29

COLOUR TEMP....................................... 29

FEATURES .............................................. 30

SOUND menu ......................................... 33

STEREO / I • II ......................................... 33

BASS........................................................ 33

TREBLE ................................................... 33

BALANCE ................................................ 33

HEADPHONE VOLUME .......................... 33

3D CINEMA SOUND................................ 33

FEATURES menu................................... 34

SLEEP TIMER ......................................... 34

CHILD LOCK............................................ 34

APPEARANCE......................................... 35

BLUE BACK ............................................. 35

SET UP menu ......................................... 36

AUTO PROGRAM (Analogue)................. 36

EDIT/MANUAL (Analogue) ...................... 36

PICTURE TILT ......................................... 40

DECODER (EXT-2).................................. 41

EXT SETTING.......................................... 42

ATTENUATOR......................................... 44

DTV menu............................................... 45

Timers (DTV Timer Recording) ................ 45

Configuration............................................ 47

Edit PR List .............................................. 49

Installation ................................................ 52

Common Interface.................................... 52

Additional preparation .......................... 53

Connecting external equipment ............... 53

Troubleshooting .................................... 56

Specifications ........................................ 59

HV-32&28D40BK_Eng.book Page 6 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial

• The connecting cables are not provided.

• For further details, refer to the manuals provided with the devices to be connected.

 If you connect via a device with an

antenna terminal such as a VCR,

follow A → B → C in the diagram

opposite.

 If you connect the antenna

directly to the TV, follow 1.

To use the T-V LINK functions, you must

have a T-V LINK compatible VCR

connected by a SCART cable C to the EXT-

2 terminal on the TV. For details about T-V

LINK functions, see “T-V LINK functions”

on page 11.

• To connect more equipment, please see

“Connecting external equipment” on

page 53.

• To connect additional audio equipment,

see “Connecting speakers/amplifier” on

page 55.

• If you connect a decoder to a T-V LINK

compatible VCR, set the DECODER

(EXT-2) function to ON. For details, see

“DECODER (EXT-2)” on page 41.

Otherwise, you will not be able to watch

scrambled channels.

• When receiving Digital terrestrial

broadcasting (DVB-T), reception can

suddenly be lost if the signal becomes

weak. Use a correctly installed high-

performance antenna.

• When connecting via a device with an

antenna terminal such as a VCR, depending

on the connection method, the signal may

be weakened. If this happens, use a booster

to increase the signal strength.

• In areas with a lot of radio communication

such as near ports or airports, noise may

be introduced into the picture or sound. In

such cases, reception may be improved by

using a high-performance antenna.

• Read the instruction manual of the

devices which you connect to the TV.

EXT-1

EXT-

EXT-2

EXT-3

AUDIO OUT

75-ohm

Coaxial

Cable

21-pin

SCART

Cable

Back of the TV

75-ohm

Coaxial

Cable

AV IN/OUT

Terminal

To Aerial

Output

To Aerial

Input

VCR

Aerial

For example

HV-32&28D40BK_Eng.book Page 7 Wednesday, April 21, 2004 1:17 PM

Setting up your TV

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

 Rear Panel

1 Aerial socket (page 7)

2 EXT-1 terminal (pages 7, 42, 53)

3 EXT-2 terminal (pages 7, 11, 42, 53)

4 EXT-3 terminal (pages 42, 53)

5 EXT-4 terminal (pages 42, 53)

6 AUDIO OUT terminal (page 55)

7 Common Interface terminal (page 52)

Connecting the power cord to

the AC outlet

Caution

• Operate only from the power source specified

(AC 220 – 240 V, 50 Hz) on the unit.

Putting the batteries into the

remote control

Use two AA/R6 dry cell batteries.

Insert the batteries from the - end, making

sure the + and - polarities are correct.

• Follow the warnings printed on the

batteries.

• Battery life is about six months to one

year, depending on how much you use the

remote control.

• The batteries we supply are only for

setting up and testing your TV, please

replace them as soon as you need to.

• If the remote control does not work

properly, replace the batteries.

Initial settings

When the TV is first turned on, it goes into

the initial settings mode, and you will see the

JVC logo. Follow the instructions on the

screen display to make the initial settings.

EXT-1

EXT- 4

EXT-2

EXT-3

AUDIO OUT

Not use

buttons

TV/DTV

HV-32&28D40BK_Eng.book Page 8 Wednesday, April 21, 2004 1:17 PM

Setting up your TV

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

1 Press the main power button on the

The power lamp lights green and the JVC

logo appears.

• If the JVC logo does not appear this is

because your TV has already been

turned on for the first time:

Perform the initial settings with

“Installation” (see page 52) in the

DTV menu and “AUTO PROGRAM

(Analogue)” (see page 36) in the SET

UP menu.

• To receive SKY 1 you need a satellite

tuner. You must have the satellite tuner

set to SKY 1 before starting the AUTO

PROGRAM function which follows.

2 Press the a button

The Digital terrestrial broadcasting

(DVB-T) Automatic Search starts.

The Digital terrestrial broadcasting

(DVB-T) channels which can be received

are automatically registered.

When the Automatic Search has

finished, the EDIT PR LIST menu

appears

• If you want to, you can now edit the

programme numbers (PR) using the

EDIT PR LIST function. For details,

see “Edit PR List” on page 49.

• If you do not want to edit programme

numbers (PR), go to the next step.

3 Press the H button

The EDIT PR LIST menu disappears and

the Analogue terrestrial broadcasting

AUTO PROGRAM starts.

The AUTO PROGRAM menu appears

and received TV channels are

automatically stored in the programme

numbers (PR).

• To cancel the AUTO PROGRAM

function:

Press the

TV/DTV button.

Main power

button

Power lamp

Installation > Automatic Search

Channels:

UHF

100%

CH:68

BBC ONE

BBC TWO

BBC THREE

BBC NEWS 24

BBCi

CBBC Channel

D0201-EN

BACK

Cancel, go to Installation Cancel, go to DTV

1 BBC ONE

Select Delete Edit Name Lock Favourites

1. BBC ONE

2. BBC TWO

7. BBC THREE

30. CBBC Channel

40. BBC NEWS 24

51. BBCi

D0202-EN

Select function Watch PR

EDIT PR LIST

Select PR

More..

CH 28

>> AUTO PROGRAM

14%

D0004-EN

Body_Eng.fm Page 9 Friday, April 23, 2004 11:20 AM

Setting up your TV

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

After the AUTO PROGRAM has

finished, the EDIT menu appears

• If you want to, you can now edit the

programme numbers (PR) using the

EDIT/MANUAL function. For details,

see “EDIT/MANUAL (Analogue)” on

page 36.

• If you do not want to edit programme

numbers (PR), go to the next step.

4 Press the a button to display the

T-V LINK menu

If you do not have a T-V LINK

compatible VCR connected:

Press the

TV/DTV button to exit the T-V

LINK menu.

The T-V LINK menu disappears.

If you have a T-V LINK compatible

VCR connected to the EXT-2

terminal:

Follow the operating procedure

“Downloading the data to VCR” on

page 11 to transmit the Programme

number (PR) data.

Now, the initial settings are complete,

and you can watch the TV

• The Analogue terrestrial broadcasting

channels BBC1, BBC2, ITV, Channel 4

and Channel 5 are automatically set to the

programme numbers PR1 to PR5. If the

TV doesn’t receive one of these TV

channels, that programme number (PR)

will not be set. Programme number PR6 is

not normally set.

• If a TV channel you want to view is not

set to a programme number (PR), you can

set it manually. To set an Analogue

terrestrial broadcasting channel, see

“EDIT/MANUAL (Analogue)” on

page 36. To set a Digital terrestrial

broadcasting (DVB-T) channel, see

“Manual Search:” on page 52.

• The AUTO PROGRAM function does not

set the programme number PR 0 (AV) for

your video cassette recorder. You will

need to set this using the MANUAL

function.

• In some areas you may get TV reception

from more than one transmitter, for

example different ITV regions. In this

case each TV channel could be set twice.

If this happens, the first set of channels

will have the stronger signal. If you want

to delete the second set of channels, you

will have to do it manually (see page 36).

> EDIT

PR ID

D0038-EK

DELETE

MANUAL

MOVE

INSERT

BBC1

BBC2

ITV

CH4

CH5

CH 21

CH 22

CH 23

CH 24

CH 25

CH 26

CH 27

CH 28

CH 29

D0005-EN

DOWNLOAD TV RECORDING DEVICE

T-V LINK

EXIT

For users in the UK:

If you have any problems setting up your

new TV, please call the

Helpline on 0870 330 5000.

Body_Eng.fm Page 10 Friday, April 23, 2004 1:32 PM

Setting up your TV

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

 Downloading the data to VCR

You can transmit to the latest Analogue

terrestrial broadcasting Programme numbers

(PR) data to a VCR with the T-V LINK

function.

Caution

• This only works when a T-V LINK

compatible VCR is connected to the

EXT-2 terminal.

• This only works when the T-V LINK

menu is being displayed.

1 Turn on the VCR

2 Press the a button

The data transmission begins.

The T-V LINK menu disappears once the

data transmission ends.

When the T-V LINK menu is

changed over to another menu:

The TV has finished its menu. This new

menu is operated from the VCR. See the

VCR instruction manual for what to do

next.

If “FEATURE NOT AVAILABLE”

appears at the T-V LINK menu:

Check the following three items. Then

press the 2 button to retry data

transmission.

• Has a T-V LINK compatible VCR

been connected to the EXT-2

terminal?

• Has the VCR power been turned on?

• Does the SCART cable that is

connected to the EXT-2 terminal to T-

V LINK compatible VCR have all its

proper connections?

T-V LINK functions

When you have a T-V LINK compatible

VCR connected to the EXT-2 Terminal on

the TV, it is easier to set up the VCR and to

view videos. T-V LINK uses the following

features:

To use T-V LINK functions:

A “T-V LINK compatible VCR” means a

JVC video cassette recorder with the T-V

LINK logo, or with one of the following

logos. However, these VCRs may support

some or all of the features described earlier.

For details, see your VCR instruction

manual.

“Q-LINK” (a trademark of Panasonic

Corporation)

“Data Logic” (a trademark of Metz

Corporation)

“Easy Link” (a trademark of Phillips

Corporation)

“Megalogic” (a trademark of Grundig

Corporation)

“SMARTLINK” (a trademark of Sony

Corporation).

 Pre-set download

The VCR will automatically download the

registered data on the TV Analogue

terrestrial broadcasting channels from the

TV. This means you do not need to set up the

program channels on your VCR manually.

The preset download function automatically

begins when the initial setting is complete or

whenever you carry out the AUTO

PROGRAM or EDIT/MANUAL functions.

You can also carry out this function using

your VCR controls.

When “FEATURE NOT AVAILABLE” is

displayed:

If “FEATURE NOT AVAILABLE” is

displayed, the download was not performed

correctly. Before trying to download again,

check that:

• the VCR power is turned on

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2

terminal

• the SCART cable is fully wired.

D0005-EN

DOWNLOAD TV RECORDING DEVICE

T-V LINK

EXIT

D0037-EN

TRANSFER. . . . .

T-V LINK TV RECORDING DEVICE

HV-32&28D40BK_Eng.book Page 11 Wednesday, April 21, 2004 1:17 PM

Setting up your TV

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

 Direct Rec

“What You See Is What You Record”

You can easily record to VCR the images

that you are watching on the TV.

For details, read the manual for your VCR.

Use your VCR controls. “DEVICE IS

RECORDING” is displayed.

You cannot carry out Direct Rec using your

TV’s control.

Generally, the VCR cannot record a TV

channel that it cannot receive properly on its

own tuner, even if you can view that TV

channel on the TV. However, some VCRs

can record a TV channel by using the TV’s

output if that channel can be viewed on the

TV. For details, see your VCR instruction

manual.

Do not turn the TV off in the following

cases.

• when recording images from an external

device connected to the TV (for example

a camcorder)

• when recording a TV channel after it has

been unscrambled on a decoder

• when recording a TV channel by using the

TV’s output because the VCR’s own

tuner cannot properly receive that

channel.

• when recording Digital terrestrial

broadcasting (DVB-T).

If you change channels or perform

other operations while a Digital

terrestrial broadcasting (DVB-T)

channel is being recorded, a window

appears asking whether to stop the

recording.

Press the a button to stop the

recording, or the

TV/DTV button to

continue the recording.

When the VCR is not ready, the following

messages are displayed.

Refer to the VCR instruction manual.

ERROR

MESSAGE

Cause and

countermeasure

RECORDING

The VCR is not able to

record.

Check the VCR.

RECORDING

POSSIBLE

The TV input is set to EXT-4.

Since the EXT-4 picture

cannot be output to EXT-2,

DIRECT REC is not possible.

RECORDING,

MEDIA

PROBLEM

The RECORDING DEVICE

is not ready to record. Check

the VCR tape.

RECORDING,

DEVICE BUSY

The RECORDING DEVICE

cannot record as it is

recording or playing. Check

the VCR.

HV-32&28D40BK_Eng.book Page 12 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

TV buttons and functions

See the pages in parentheses for details.

1 Main power button (pages 9, 13)

2 Power lamp (pages 9, 13)

3 Remote control sensor

4 r (Volume) button (page 14)

5 P p buttons/ q buttons (page 13)

6 Headphone jack (mini jack) (page 53)

7 EXT-5 terminal (pages 42, 53)

Turn the main power on

Press the main power button on the

TV.

The power lamp lights red and your TV is in

standby mode.

• If the power lamp lights green, the TV is

already on.

To turn the main power off:

Press the main power button again.

The power lamp goes off.

Caution

• The main power button on the TV does

not fully isolate the TV from the AC

supply. If you are not going to use the TV

for a long period, be sure to disconnect

the AC plug from the AC socket.

Turn the TV on from standby

mode

Press the P p buttons to turn the TV

on from standby mode

Choose a TV channel

Press the P p buttons to choose a

programme number (PR) or an EXT

terminal

The EXT terminal cannot be chosen when

watching Digital terrestrial broadcasting

(DVB-T).

To switch between Analogue

terrestrial broadcasting and Digiatl

terrestrial broadcasting (DVB-T):

1 Press the r (Volume) button

2 Press the r (Volume) button

again when the volume level

indicator appears

MONO

EXT-5

MONO

EXT-5

HV-32&28D40BK_Eng.book Page 13 Wednesday, April 21, 2004 1:17 PM

TV buttons and functions

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Adjust the volume

1 Press the r (Volume) button once

The volume level indicator appears.

2 Press the q buttons while the

volume level indicator is displayed

HV-32&28D40BK_Eng.book Page 14 Wednesday, April 21, 2004 1:17 PM

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Remote control buttons and functions

1 Muting button

2 Number buttons

3 Information button

4 Colour button

TV/DTV button

6 7 buttons

7 g (Text) button

8 p p buttons

9 VCR/DVD/Teletext control buttons

0 p buttons

- c button

= 3 button

~ # (Standby) button

! VCR/TV/DVD switch

@ G button

# H button

$ a button

% b button

^ r (Volume) q buttons

GUIDE button

* SUBTITLE button

( X (Multi) button

) f/g (Freeze/Swap) button

Turn the TV on or off from

standby mode

Press the # (standby) button to turn

the TV on or off.

When the TV is turned on, the power lamp

lights green.

• The power can be turned on by pressing

the

TV/DTV button, p p buttons or

Number buttons.

(

)

To turn the TV on or off, set the VCR/TV/

DVD switch on the remote control to the

TV position and press the # button.

If the VCR/TV/DVD switch on the remote

control is set to a position other than TV,

the TV will not be turned on or off even if

the # button is pressed.

HV-32&28D40BK_Eng.book Page 15 Wednesday, April 21, 2004 1:17 PM

Remote control buttons and functions

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Choose a TV channel and

watch images from external

devices

• If the picture is tilted, correct it. See

“PICTURE TILT” on page 40.

 Switching between Digital

terrestrial broadcasting (DVB-T)

and Analogue terrestrial

broadcasting.

Press the TV/DTV button.

The broadcasting is switched every time the

button is pressed.

 Use the number buttons:

Enter the programme number (PR)

of the channel using the number

buttons.

Example:

•PR 6 → press 6

• PR 12 → press 1 and 2

• PR 123 → press 1, 2 and 3

 Use the p p buttons:

Press the p p buttons to

choose the programme number

(PR) you want.

• For Digital terrestrial broadcasting (DVB-

T), if the FAVOURITE setting in the

“Edit PR List” (see page 49) has been set,

only that programme number (PR) can be

chosen.

• For Analogue terrestrial broadcasting, an

EXT terminal can also be chosen.

 Use the AV button:

Press the AV button to choose an

EXT terminal.

• You can choose a video input signal

from the S-VIDEO signal (Y/C signal)

and regular video signal (composite

signal). For details, see “S-IN (S-

VIDEO input)” on page 42.

• If you do not have a clear picture or no

colour appears, change the colour

system manually. See “COLOUR

SYSTEM” on page 31.

• If you choose an EXT terminal with no

input signal, the EXT terminal number

becomes fixed on the screen.

• This TV set has a function which can

automatically change over the input

according to a special signal output

from an external device. (The EXT-4

and EXT-5 terminals do not support

this function.)

• Since this TV is designed to make full

use of the resolution of the original

video source, the motion may appear

unnatural when the video source is

input with 625p progressive-scanning

component signals.

If this happens, change the output

setting of the connected device to 625i

interlace-scanning component signal

output. See the instructions that came

with the device for more information.

To return to a TV channel:

Press the

TV/DTV button, the p p buttons

or the number buttons.

EXT-1

Analogue

terrestrial

broadcasting

Digital

terrestrial

broadcasting

(DVB-T)

EXT-5

EXT-2

EXT-4

EXT-3

TV mode EXT modes

HV-32&28D40BK_Eng.book Page 16 Wednesday, April 21, 2004 1:17 PM

Remote control buttons and functions

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

To use the programme number PR 0

(AV):

When the TV and VCR are connected only

by the aerial cable, choosing the programme

number PR 0 (AV) allows you to view

images from the VCR. Set the VCR RF

channel to the programme number PR 0

(AV) manually. For details, see “EDIT/

MANUAL (Analogue)” on page 36.

Pressing the G button changes the choice as

follows:

• The VCR sends its playback image along

the aerial cable as an RF (radio frequency)

signal.

• Also see your VCR instruction manual.

Adjust the volume

Press the r q buttons to adjust

the volume.

The volume indicator appears and the

volume changes as you press the r q

buttons.

 Muting the sound

Press the

(muting) button to

turn off the sound.

Pressing the

(muting) button again

restores the previous volume level.

Information function

When watching Digital terrestrial

broadcasting (DVB-T):

When the h (Information) button is pressed,

the programme information appears for

approximately 1 minute.

• When the h (Information) button is

pressed while the information is being

displayed, the information disappears.

• The time display in the programme

information uses the time information

which is included in the Digital terrestrial

broadcasting (DVB-T). Depending on the

channel, the time information may not be

correct.

When watching Analogue terrestrial

broadcasting:

You can see the channel number of the

programme you are watching, the current

time or the PR LIST.

From the PR LIST, you can choose a channel

or EXT terminal.

Press the

(Information) button to

display the information you want to

see.

Pressing the

(Information) button changes

the display as follows:

EXT-1PR 0

Analogue

terrestrial

broadcasting

Digital terrestrial

broadcasting

(DVB-T)

EXT-5

EXT-2

EXT-4

EXT-3

TV mode EXT modes

D0203-EN

Now: 13:00-14:00 Steve Scott

Next: 14:00-14:30 Steve Scott

ITV News

13:19

CH61

PR ID

BBC1

D0011-EN

12 : 00

PR LIST

+10-10

No indication

Channel number display

HV-32&28D40BK_Eng.book Page 17 Wednesday, April 21, 2004 1:17 PM

Remote control buttons and functions

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

Channel number display:

The channel number and channel name

(when the channel name is registered) of the

programme you are watching or the EXT

terminal number is displayed.

Time display:

The current time of the teletext data is

displayed.

If the TV has not received a TV channel that

has teletext programmes since it was turned

on, the time display is blank. To view the

current time, choose a TV channel that has

teletext programmes.

• An incorrect current time is sometimes

displayed when watching videos.

PR LIST:

The programme number (PR) and EXT

terminal list is displayed.

Pressing the a button after choosing the

programme number (PR) or EXT terminal

with the 7 buttons will display the

chosen programme or EXT terminal.

• For programme numbers (PR) for which

the CHILD LOCK function is set, the n

(CHILD LOCK) mark is displayed. For

details see “CHILD LOCK” on page 34.

ZOOM function

You can change the screen size according to

the picture aspect ratio. Choose the optimum

one from the following ZOOM modes.

AUTO:

When a WSS (Wide Screen Signalling)

signal, which shows the aspect ratio of the

picture, is included in the broadcast signal or

the signal from an external device, the TV

automatically changes the ZOOM mode to

16:9 ZOOM mode or FULL mode according

to the WSS signal.

If a WSS signal is not included, the picture is

displayed according to the ZOOM mode set

with the 4:3 AUTO ASPECT function.

• For details of the 4:3 AUTO ASPECT

function, see “4:3 AUTO ASPECT” on

page 32.

• When the AUTO (WSS) mode does not

function correctly due to poor WSS signal

quality or when you want to change the

ZOOM mode, press the c button

and change to another ZOOM mode.

• When watching a 16:9 FULL programme

with Digital terrestrial broadcasting

(DVB-T), the aspect ratio is FULL.

REGULAR:

Use to view a normal picture (4:3 aspect

ratio) as this is its original shape.

PANORAMIC:

This stretches the left and right sides of a

normal picture (4:3 aspect ratio) to fill the

screen, without making the picture appear

unnatural.

• The top and bottom of the picture are

slightly cut off.

HV-32&28D40BK_Eng.book Page 18 Wednesday, April 21, 2004 1:17 PM

Remote control buttons and functions

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect

ratio) to the upper and lower limits of the

screen.

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect

ratio) to the full screen.

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect

ratio) with subtitles to the full screen.

FULL:

This uniformly stretches the left and right

sides of a normal picture (4:3 aspect ratio) to

fill the wide TV screen.

• For 16:9 aspect ratio pictures that have

been squeezed into a normal picture (4:3

aspect ratio), use the FULL mode to

restore the picture to its original shape.

• When you use this TV’s output signal to

record a Digital terrestrial broadcasting

(DVB-T) 16:9 broadcast, it will be

recorded with its picture squeezed into a

4:3 aspect ratio picture.

Use the FULL mode to restore the picture

to its original shape when playing the

recording.

 Choose the ZOOM mode

1 Press the c button to display

the ZOOM menu

2 Press the 6 buttons to choose a

ZOOM mode. Then press the a

button

The picture expands and the chosen

ZOOM mode is displayed in about 5

seconds.

• The ZOOM mode may be

automatically changed by the control

signal from an external device. When

you want to return to the previous

ZOOM mode, choose the ZOOM

mode again.

 Adjusting the visible area of the

picture

If subtitles or the top (or bottom) of the

picture are cut off, you can adjust the visible

area of the picture manually.

1 Press the c button

The ZOOM menu appears.

2 Press the a button to display the

ZOOM mode indicator

The indicator appears.

3 While it is displayed, press the 6

buttons to change the position of

the picture

• You cannot adjust the visible area in

REGULAR or FULL mode.

• Some menu displays can be cut off when

you move the visible area up or down

while watching Digital terrestrial

broadcasting (DVB-T).

D0009-EN

AUTO

REGULAR

PANORAMIC

14:9 ZOOM

16:9 ZOOM

16:9 ZOOM SUBTITLE

FULL

ZOOM

16 : 9 ZOOM

D0010-EN

HV-32&28D40BK_Eng.book Page 19 Wednesday, April 21, 2004 1:17 PM

Remote control buttons and functions

HV-32/28D40BK / LCT1596-001A-U / ENGLISH

3D CINEMA SOUND function

You can enjoy sounds with a wider

ambience.

• This function does not work for the sound

from headphones.

Press the 3 button and choose

“ON”, “MONO” or “OFF”.

ON:

Choose to add the 3D CINEMA SOUND

effect to stereo sound.

MONO:

Choose to add the 3D CINEMA SOUND

effect to mono sound.

OFF:

Choose to cancel the 3D CINEMA SOUND

effect.

• The 3D CINEMA SOUND effect can be

adjusted with the “3D CINEMA

SOUND” menu (see page 33).

Using the FREEZE function

This function can only be used when

watching Analogue terrestrial

broadcasting.

You can view the current programme as a

still picture.

1 Press the f button

The still picture of the current picture will

appear.

To cancel the FREEZE function:

Press the f button, the p p buttons or

the number buttons.

• The FREEZE function does not work

while a sub-picture is displayed.

• The still picture cannot be output from

the TV.

• The FREEZE function does not work

for pictures of 1125i signal.

Using the MULTI-PICTURE

function

When watching Digital terrestrial

broadcasting (DVB-T):

1 Press the X button

The MULTI-PICTURE menu appears.

2 Press the 5 buttons and choose

2, then press the a button

2-pictures multi:

• You can watch Digital terrestrial

broadcasting (DVB-T) in the main-

picture. You can watch the Analogue

terrestrial broadcasting or EXT picture

in the sub-picture.

• When the Digital terrestrial

broadcasting (DVB-T) in the main-

picture is 16:9 FULL, the main-picture

aspect ratio is 16:9.

• The main-picture sound is emitted

from the TV speaker. If headphones

are connected, you can listen to the

sub-picture sound. Adjust the

headphone volume with

HEADPHONE VOLUME in the

SOUND menu. The main-picture

sound cannot be listened to with the

headphones.

D1056-EN

current

programme

still picture

D0101-EN

212

D0102

D0103

Choose to return to one screen.

Choose to change to 2-pictures multi.

D1056-EN

Main-

picture

Sub-

picture

D0104

This cannot be chosen when watching

Digital terrestrial broadcasting (DVB-T).

HV-32&28D40BK_Eng.book Page 20 Wednesday, April 21, 2004 1:17 PM

Page is loading ...

JVC HV-28D40BK User manual

Brand: JVC

Model: HV-28D40BK

Category: LCD TVs

Type: User manual

This manual is also suitable for

Download PDF

report

JVC HV-28D40BK User manual

This manual is also suitable for

JVC HV-28D40BK User manual

Related papers

Other documents