Pioneer PDP-4330HD User manual

Operating Instructions

Mode d'emploi

Manual de instrucciones

PLASMA DISPLAY SYSTEM

SYSTEME D'ÉCRAN PLASMA

SISTEMA DE PANTALLA DE PLASMA

PDP-5030HD

PDP-4330HD

Note to CATV system installer.

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides

guidelines for proper grounding and, in particular, specifies that the cable ground–shall be connected to the

grounding system of the building, as close to the point of cable entry as practical.

WARNING: THE APPARATUS IS NOT WATERPROOFS, TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE AND DO NOT PUT ANY WATER SOURCE NEAR THIS

APPARATUS, SUCH AS VASE, FLOWER POT, COSMETICS CONTAINER AND MEDICINE BOTTLE ETC.

NOTE:

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

— Consult the dealer or an experienced radio/TV technician for help.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the

equipment.

[For Canadian model]

This Class B digital apparatus complies with Canadian ICES-003.

CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other

equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded

cables and connectors for connections.

FEDERAL COMMUNICATIONS COMMISSION

DECLARATION OF CONFORMITY

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Product Name: Plasma Display System

(Plasma Display)

(Media Receiver)

Model Number: PDP-5030HD PDP-4330HD

(PDP-503PU) (PDP-433PU)

(PDP-R03U) (PDP-R03U)

Product Category: Class B Personal Computers & Peripherals

Responsible Party Name: PIONEER ELECTRONICS (USA), INC., Customer Support Div.

Address: P.O. BOX 1760, LONG BEACH, CA., 90801-1760 U.S.A.

Phone: (800) 421-1625

For Business Customer URL http://www.PioneerUSA.com

IMPORTANT NOTICE: The serial number for this equipment is located on the rear panel. Please write this

serial number on your enclosed warranty card and keep it in a secure area. This is for your security.

E-1

Dear customer

Thank you for your purchase of the PIONEER product. To ensure safety and many years of trouble-free operation

of your product, please read the IMPORTANT SAFETY INSTRUCTIONS carefully before using this product.

Contents

Dear customer ……………………………………… 1

Contents ……………………………………………… 1

Important User Guidance Information ……………2

Features ……………………………………………… 3

Supplied accessories ……………………………… 4

Plasma Display ……………………………………4

Media Receiver ……………………………………4

Preparation ……………………………………………5

Installing the Plasma Display ……………………5

Setting the system ……………………………… 6

How to route cables ……………………………… 7

Using the remote control unit …………………… 8

Cautions regarding remote control unit …… 8

Inserting the batteries ……………………… 8

Cautions regarding batteries ………………8

Part names ……………………………………………9

Plasma Display ……………………………………9

Media Receiver ………………………………… 10

Remote control unit …………………………… 11

Watching TV ……………………………………… 12

Basic connection ……………………………… 12

Turning on the power ………………………… 14

Turning off the power ………………………… 14

Initial auto installation ………………………… 15

Simple button operations for changing

channels …………………………………… 16

Simple button operations for changing

volume/sound ……………………………… 17

Using FRONT SURR(SURROUND) on the

remote control unit ………………………… 18

Setting MTS/SAP stereo mode ……………… 19

Basic adjustment settings ……………………… 20

AV mode menu items ………………………… 20

PC mode menu items ………………………… 21

Moving the picture on the screen …………… 22

Auto installation ………………………………… 23

Channel setup ………………………………… 24

Language setting ……………………………… 26

Picture adjustments …………………………… 27

Color temperature ………………………… 28

Black ……………………………………… 28

3D-Y/C ……………………………………… 29

Black & White ……………………………… 29

PureCinema………………………………… 30

Sound adjustment ……………………………… 31

Power control …………………………………… 32

Power control for AV source ……………… 32

Power control for PC source ……………… 33

Using external equipment ……………………… 34

Watching a DVD image ……………………… 35

Connecting a DVD player ………………… 35

Displaying a DVD image ………………… 35

Watching a VCR image ……………………… 36

Connecting a VCR ………………………… 36

Displaying a VCR image ………………… 36

Watching broadcasts via a Digital tuner …… 37

Connecting a Digital tuner ……………… 37

Displaying broadcasts via a Digital tuner 37

Enjoying a game console or viewing camcorder

images ……………………………………… 38

Connecting a game console or

camcorder …………………………… 38

Displaying an image of the game console

or camcorder images ………………… 38

Viewing an image from a computer ………… 39

Connecting a computer ………………… 39

Displaying an image from a computer … 39

Control cord connection ……………………… 40

Useful adjustment settings ……………………… 41

Image position (AV mode only) ……………… 41

Auto Sync. adjustment (PC mode only) …… 42

Fine Sync. adjustment (PC mode only) ……… 42

Input signal source …………………………… 43

AV SELECTION ………………………………… 44

Wide Mode ……………………………………… 45

Audio out ……………………………………… 46

Sleep timer ……………………………………… 46

Closed caption ………………………………… 47

Parental control (setting V-CHIP level) ……… 48

Secret number setting for parental control

(AV mode only) …………………………… 52

How to temporarily release

the V-CHIP BLOCK ……………………… 54

Reactivating the temporarily released

V-CHIP BLOCK …………………………… 54

Useful features …………………………………… 55

Multiscreen functions ………………………… 55

Learning remote control function …………… 56

Using the TV remote control unit to

control other device ……………………… 58

Appendix ………………………………………… 64

Troubleshooting ………………………………… 64

Computer compatibility chart ………………… 65

Specifications ………………………………… 66

E-2

Important User Guidance Information

In order to obtain maximum enjoyment from this Pioneer PureVision PDP-5030HD/PDP-4330HD Plasma Display System, please first read

this information carefully.

With the Pioneer PureVision PDP-5030HD/PDP-4330HD, you can be assured of a high quality Plasma Display System with long-life and

high reliability. To achieve images of exceptional quality, this Pioneer Plasma Display System incorporates state-of-the-art design and

construction, as well as very precise and highly advanced technology. On a total of nearly 3 million light cells, more than 99.999 percent

of the cells remain active.

Over the course of its lifetime, the luminosity of the Pioneer PDP-5030HD/PDP-4330HD Plasma Display System will diminish very slowly,

such as with all phosphor-based screens (for example, a traditional tube-type television). To enjoy beautiful and bright images on your

Pioneer Plasma Display System for many years to come, please carefully read and follow the usage guidelines below.

Usage guidelines

All phosphor-based screens (including conventional tube-type televisions) can be affected by displaying static images for a prolonged

period. Plasma Display Systems are no exception to this rule. After-image and permanent effects on the screen can be avoided by taking

some basic precautions. By following the recommendations listed below, you can ensure longer and satisfactory results from your plasma:

• Whenever possible, avoid frequently displaying the same image or virtually still moving pictures (e.g. closed-captioned images or

video game images which have static portions).

• Avoid viewing the On Screen Display for extended periods, from a Digital tuner, DVD player, VCR and all other components.

• Do not leave the same picture freeze-framed or paused continuously over a long period of time, when using the still picture mode

from a TV, VCR, DVD player or any other component.

• Images which have both very bright areas and very dark areas side by side should not be displayed for a prolonged period of time.

• When playing a game, the “GAME” mode setting within “AV SELECTION” is strongly recommended. However, please limit its use to

less than 2 hours at a time.

• After playing a game, or displaying a PC image or any still image, it is best to view a normal moving picture in the “WIDE” or “FULL”

screen setting for over 3 times longer than the previous still/moving image.

• After using the Plasma Display System, always switch the display to “STAND BY” mode.

Installation guidelines

The Pioneer PureVision PDP-5030HD/PDP-4330HD Plasma Display System incorporates a very thin design. To ensure safety, please take

the proper measures to mount or install the Plasma Display, in order to prevent the unit from tipping over in the event of vibration or

accidental movement.

This product should be installed by using only parts and accessories designed by PIONEER. Use of accessories other than the PIONEER

stand or installation bracket may result in instability, and could cause injury. For custom installation, please consult the dealer where the

unit was purchased. To ensure correct installation, experienced and qualified experts must install the unit. PIONEER will not be held

responsible for accident or damage caused by the use of parts and accessories manufactured by other companies.

To avoid malfunction and overheating when installing, make sure that the vents on the main unit are not blocked. To ensure proper heat

emission:

• Distance the unit slightly from other equipment, walls, etc. more than 10 cm(3

15

/16 inch)

• Do not fit the unit inside narrow spaces where ventilation is poor.

• Do not cover with a cloth, etc.

• Clean the vents on the sides and rear of the unit to remove dust build-up by using a vacuum cleaner set to its lowest

suction setting.

Using the unit without proper ventilation may cause the internal temperature to rise, and could result in possible malfunction. When the

surrounding or internal temperature exceeds a certain degree, the display will automatically power off in order to cool the internal electronics

and prevent a hazardous occurrence.

Malfunction can be caused by many factors: inappropriate installation site, improper assembly/installation/mounting, improper operation

of or modifications made to this product. However, PIONEER cannot be held responsible for accidents or malfunction caused by the

above.

A

Typical effects and characteristics of a phosphor-based matrix display such as permanent residual images upon the phosphors of the

panel and the existence of a minute number of inactive light cells in the screen are not covered by local warranties.

About the Plasma Panel’s protection function

The brightness of this display will deteriorate slightly when an image with little movement such as a photograph or computer image is

continuously displayed. This is caused by the Plasma Panel's protection function which detects images with slight movement and

automatically adjusts brightness to protect the display, and is not a malfunction.

This function begins operating when the display detects no or little screen movement for a period of about three minutes.

L

Panel sticking and after-image lag

• Displaying the same images such as still images for a long time may cause after-image lagging. This may occur in the following two

cases.

1. After-image lagging due to remaining electrical load

When image patterns with very high peak luminance are displayed for more than 1 minute, after-image lagging may occur due to the

remaining electric load. The after-images remaining on the screen will disappear when moving images are displayed. The time for the

after-images to disappear depends on the luminance of the still images and the time they had been displayed.

2. After-image (lag image) due to burning

Avoid displaying the same image on the Plasma Display continuously over a long period of time. If the same image is displayed

continuously for several hours, or for shorter periods of time over several days, a permanent after-image may remain on the screen due

to burning of the fluorescent materials. Such images may become less noticeable if moving images are later displayed, but they will not

disappear completely.

• The Energy save function can be set to help prevent damage from screen burning (See page 32-33).

E-3

Features

• New WIDE XGA Plasma Panel

(H:1280 m V:768 pixels, PDP-5030HD)

(H:1024 m V:768 pixels, PDP-4330HD)

• Wide Viewing Angle

• SRS and FOCUS Sound System*

1

• Dual TV Tuner

• Picture and Picture, Still Image Function

• 3-Language On Screen Display

• 4 Video Input and PC (XGA) Input

• Component Video Input and RGB Video Input

• Parental Control System (V-CHIP)

• Power-Saving Design

E-4

Supplied accessories

Plasma Display

Power cord

Cleaning cloth

Three speed clamps

Three bead bands

Warranty card

Media Receiver

Power cord Remote control unit

Two AA size batteries

(Alkaline battery)

System cable Operating instruction

A

• Always use the power cord supplied with the Plasma Display and the one supplied with the Media Receiver for each

respective unit.

E-5

Preparation

Installing the Plasma Display

Locating

• Avoid the direct sunlight. Keep enough ventilation.

• The length of the system cable used to connect the

Plasma Display and the Media Receiver is about 3

m (118 inch).

• Because the Plasma Display is heavy, be sure to

move it by more than two persons.

L

• If you place anything on top of the Media Receiver it will

not receive enough ventilation and not operate properly.

A

• Keep enough space around the upper and back parts

when installing in order to ensure ventilation around the

backside.

Using the optional PIONEER stand

• For details on installation refer to the instruction

manual provided with the stand.

L

• This product may be used only with model PDK-TS01

stand, use with other stands may result in instability

causing possible injury.

Using the optional PIONEER speakers

• For details on installation refer to the instruction

manual provided with the speaker.

L

Operating Environment

Operating environment temperature and humidity: e0°C to

e40°C (e32F to e104F); less than 20 % to 80% RH (cooling

vents not blocked)

Avoid installing in the following locations:

• Under direct exposure to sunlight,

• Under strong artificial light,

• In high humidity,

• Poorly ventilated.

Over

10 cm

(3

15

/16

inch )

Over 50 cm

(19

11

/16 inch)

E-6

Preparation

System cable

Media Receiver (rear view)

Power cord

Plasma Display (rear view)

Power cord

System cable

(bottom view)

For details on optional

PIONEER speaker

installation refer to the

speaker instruction

manual provided.

(GRAY)(WHITE)

(GRAY) (WHITE)

Setting the system

1. Connecting the system cable and the power cord to the Plasma Display

2. Connecting the system cable and the power cord to the Media Receiver

L

• THESE SPEAKER TERMINALS CAN BE UNDER HAZARDOUS VOLTAGE WHEN YOU CONNECT OR DISCONNECT

THE SPEAKER CABLES. TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT TOUCH UNINSULATED PARTS

BEFORE DISCONNECTING THE POWER CORD.

(GRAY)

RS-232C

IN

OUT

CONTROL

AC INLET

SYSTEM

CABLE

(WHITE)

YP

B

P

R

S-VIDEO VIDEO R-AUDIO-L

YP

B

P

R

S-VIDEO

ANT/CABLE 75ΩOUT

COMPONENT VIDEO COMPONENT VIDEO

VIDEO R-AUDIO-L

AB

INPUT 1

INPUT 2

RGB INPUT

INPUT 3

MONITOR OUTPUT

E-7

Bunch cables using provided speed clamps

Attaching speed clamps to the main unit

Connect the speed clamps using the 4 holes marked with • below, depending on your routing system.

Attaching and removing speed clamps

Insert 1 into an appropriate hole on the rear of the Plasma Display and snap 2 into the back of 1 to fix the

clamp.

Speed clamps are designed to be difficult to undo once in place. Please attach carefully.

Use pliers to twist the clamp 90°, pulling outward. The clamp may deteriorate over time and become damaged

if removed.

Gather cables into a bunch, secure with provided bead bands

A

• Cables can be routed to the right or left.

Preparation

How to route cables

Speed clamps and bead bands are included with this System for bunching cables. Once properly bunched,

follow the steps below to route the cables.

As viewed from the rear of the display.

1

2

System cable Speed clamps Bead bands Speaker cable

System cableSpeaker cable Speed clamps Bead bands

To the left

To the right

E-8

Preparation

+

_

Using the remote control unit

Use the remote control unit by pointing it towards the remote sensor window.

Objects between the remote control unit and sensor window may prevent proper

operation.

Cautions regarding remote control unit

• Do not expose the remote control unit to shock. In addition, do not expose the

remote control unit to liquids, and do not place in an area with high humidity.

• Do not install or place the remote control unit under direct sunlight. The heat

may cause deformation of the unit.

• The remote control unit may not work properly if the remote sensor window of

the Plasma Display is under direct sunlight or strong lighting. In such case,

change the angle of the lighting or Plasma Display set, or operate the remote

control unit closer to the remote sensor window.

Inserting the batteries

If the remote control unit fails to operate Plasma Display System functions,

replace the batteries in the remote control unit.

1 Open the battery cover. 2 Insert batteries (two AA size

batteries supplied with product).

• Place batteries with their terminals

corresponding to the (e) and (f)

indicators in the battery compartment.

3 Close the battery cover.

Cautions regarding batteries

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

• Do not use manganese batteries. When you replace the batteries, use alkaline ones.

• Place the batteries with their terminals corresponding to the (e) and (f) indicators.

• Do not mix batteries of different types. Different types of batteries have different characteristics.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause

chemical leakage in old batteries.

• Remove batteries as soon as they have worn out. Chemicals that leak from batteries can cause a rash. If you

find any chemical leakage, wipe thoroughly with a cloth.

• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.

• If you do not plan to use the remote control unit for an extended period of time, remove the batteries from it.

L

• WHEN DISPOSING OF USED BATTERIES, BE SURE TO COMPLY WITH GOVERNMENT REGULATIONS AND

ENVIRONMENTAL PROTECTION GUIDELINES THAT APPLY IN YOUR COUNTRY OR AREA.

E-9

Part names

STANDBY/ON

INPUTSTANDBY/ON VOLUMECHANNEL

MAIN POWER button

Power indicator

STANDBY/ON button

INPUT button VOLUME s/r buttons

CHANNEL s/r buttons Remote control sensor

Plasma Display

E-10

Part names

(GRAY)

RS-232C

IN

OUT

CONTROL

AC INLET

SYSTEM

CABLE

(WHITE)

YP

B

P

R

S-VIDEO VIDEO R-AUDIO-L

YP

B

P

R

S-VIDEO

ANT/CABLE 75ΩOUT

COMPONENT VIDEO COMPONENT VIDEO

VIDEO R-AUDIO-L

AB

INPUT 1

INPUT 2

RGB INPUT

INPUT 3

MONITOR OUTPUT

POWER

STANDBY/ON

MEDIA RECEIVER

PDP-R03U

Front view

CLEAR*

POWER button

INPUT 4 terminal (S-VIDEO)

INPUT 4 terminal (VIDEO)

PC INPUT terminal (AUDIO) INPUT 4 terminals (AUDIO)

PC INPUT terminal (ANALOG RGB)

Media Receiver

* If you’re having problems operating the Media Receiver and want to return to normal screen, even when it

stays on (the indicator lights green), press CLEAR on the Media Receiver. Pressing CLEAR resets the System

as shown below.

• AV SELECTION resets to STANDARD

• TV channel returns to initial channel setting(Air:2ch, Cable:1 or 2ch)

• Multiscreen resets to normal

• Audio setting initializes

• SRS resets to Off.

• Image position initializes

A

• Pressing CLEAR will not work if the System is in standby mode but the indicator lights red.

• Pressing CLEAR will not delete channel preset or secret number. See Page 53 for initializing factory preset settings when

you know your secret number. See Page 67 for initializing factory preset values when you have forgotten your secret

number.

Rear view

INPUT 1 COMPONENT VIDEO

terminals (Y, P

B, PR)

INPUT 3 COMPONENT

VIDEO terminals (Y, P

B, PR)

MONITOR OUTPUT

terminal (S-VIDEO)

SYSTEM CABLE terminal

(GRAY)

SYSTEM CABLE

terminal (WHITE)

AC INLET terminal

RS-232C terminal

(used in the factory setup)

MONITOR OUTPUT

terminal (VIDEO)

MONITOR OUTPUT

terminals (AUDIO)

CONTROL terminals

(IN/OUT)

Antenna input

terminal (A)

Antenna input

terminal (B)

Antenna output

terminal

INPUT 3

RGB INPUT

terminal

INPUT 3 terminal

(S-VIDEO)

INPUT 3 terminal

(VIDEO)

INPUT 3 terminals

(AUDIO)

INPUT 1 terminal

(S-VIDEO)

INPUT 1 terminal

(VIDEO)

INPUT 1 terminals

(AUDIO)

INPUT 2 terminal

(S-VIDEO)

INPUT 2 terminal

(VIDEO)

INPUT 2 terminals

(AUDIO)

Push CLEAR lightly with the tip

of a pointed object like a

ballpoint pen.

E-11

Part names

Remote control unit

A

• When using the remote control unit, point it at the Plasma

Display.

• See pages 56 to 63 for operating buttons not listed on

this page.

Set the mode switch to TV.

1TV a: Switch the Plasma Display power on or off.

2 FRONT SURR: Set SRS and FOCUS Sound System.

3 AV SELECTION: Select an audio or video setting.

(AV mode: STANDARD, DYNAMIC,

MOVIE, GAME, USER.

PC mode: STANDARD, USER.)

4 SCREEN MODE: Select the screen size.

5 DISPLAY: Display the channel information.

6 SLEEP: Set the SLEEP timer.

7 CH RETURN: Return to the previous channel.

8CH k/l: Select the channel.

9 MENU: Display the menu screen.

10 MENU RETURN: Return to the previous menu screen.

11 a/b/c/d: Select a desired item on the setting screen.

12 ANT: Select the antenna. (A, B) (See page 12 for details)

13 INPUT: Select an input source of the Plasma Display.

(TV, INPUT 1, INPUT 2, INPUT 3, INPUT 4, PC)

14

: When pressed all buttons on the remote control unit

will light. The lighting will turn off if no operations

are performed within about 5 seconds. This button

is used for performing operations in dark places.

15 MTS: Select the MTS/SAP.

16 CC: Display captions during closed-caption source.

17 Dual picture mode select buttons

SPLIT: Set the dual picture mode. Press again to return

to normal screen.

FREEZE: Set the still image. Press again to return to

normal screen.

SELECT: Select the active screen.

SUB INPUT: Select an input source of sub screen.

SUB CH k/l: Select the channel of sub screen.

18 0 – 9: Set the channel.

19 CH ENTER: Execute a channel number.

20 VOL k/l: Set the volume.

21 e MUTING: Mute the sound.

22 SET/ENTER: Execute a command.

23 FAVORITE CH

A, B, C, D: Select any of four preset channels. (See

page 25 for ditails to set the FAVORITE CH.)

While watching you can toggle the set channels by

pressing A, B, C and D.

24 LED for transmission confirmation

TV

ANT INPUT

SURR

FRONT

AV

SELECTION

MTS CC

SPLIT

SELECT

SUB SUB CH

ⴐ

ⴑ

ⴐ

ⴑ

FREEZE

MODE

CH VOL

RETURN

CH

MUTING

MENU TV/SAT/DVD

FAVORITE CH

RECEIVER

DTV/DVD TOP

SOURCE DTV/SAT

DTV/SAT

VCR REC

ABCD

RETURN

MENU

PLASMA DISPLAY

SET/

ENTER

MENU

GUIDE

INPUT VOL

ⴑ

VOL

ⴐ

INFO

SCREEN

SLEEP LEARNEDIT/

DISPLAY

INPUT ⴑ

TV VCRCBL

/SAT

/DTV

DVD

/LD

123

456

789

0

CH

ENTER

11224 13

15

16

14

17

18

19

4

3

2

5

6

7

20

21

22

23

8

9

10

11

Mode switch

E-12

Watching TV

Simple operations for watching a TV program

Basic connection

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections

that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,

plug it into the antenna terminal at the rear of the Media Receiver.

A

• The Antenna and CABLE Converter cannot be connected at the same time.

A

OUT

B

A

OUT

B

Connecting VHF/UHF antenna

Connecting the CABLE Converter

VHF antenna UHF antenna

U/V mixer

Media Receiver (rear)

CABLE TV

CABLE Converter

A

• Be sure connect the Antenna or the CABLE Converter as explained above. Signal reception may fail if not properly

connected.

• Be sure that the CABLE Converter output signal is assigned to the ANT-B input on the Media Receiver.

• How to change channels when the CABLE Converter output signal is connected to the ANT-B input on the Media Receiver.

•Press ANT on the remote control unit to switch to ANT-B.

•You can view an image right after selecting the output channel on the CABLE Converter.

Switching between Tuner A and Tuner B

To watch broadcasts via the two tuners, you can select it by pressing ANT on the remote control unit.

• While watching a broadcast press ANT to view the image received from the other tuner.

• Pressing ANT while viewing in Dual Screen mode (TV image and video image) with TV selected will display the TV image

of the other tuner.

• Pressing ANT while viewing Dual Screen with video selected will not change the image displayed.

• Pressing ANT while viewing Dual Screen with two TV images displayed will not have any effect.

• Pressing ANT while viewing Dual Screen with two video images displayed will switch the selected screen to a TV image.

The coaxial cable is already

connected at the time of

purchase.

E-13

AC INLET

(GRAY)

RS-232C

IN

OUT

CONTROL

AC INLET

SYSTEM

CABLE

(WHITE)

YP

B

P

R

S-VIDEO VIDEO R-AUDIO-L

YP

B

P

R

S-VIDEO

ANT/CABLE 75ΩOUT

COMPONENT VIDEO COMPONENT VIDEO

VIDEO R-AUDIO-L

AB

INPUT 1

INPUT 2

RGB INPUT

INPUT 3

MONITOR OUTPUT

AC INLET

Power cord

Connecting the power cord

Connect the power cord after all component connections have been completed.

Watching TV

Plasma Display (bottom view)

Media Receiver (rear view)

L

• Use only the power cord provided.

• Do not use a power supply voltage other than that indicated (AC 120 V, 60 Hz) as this may cause fire or electric shock.

• For the Plasma Display System, a three-core power cord with a ground terminal is used for efficiency protection. Always

be sure to connect the power cord to a three-pronged outlet and make sure that the cord is properly grounded. If you use

a power source converter plug, use an outlet with a ground terminal and screw down the ground line.

A

• Always turn off the main power of Plasma Display and Media Receiver when connecting the power cords.

• Disconnect the power cord from the power outlet when the Plasma Display System is not going to be used for a long

period of time.

E-14

Watching TV

Plasma Display

Media Receiver

Off

Flashing red

Red

Green

Plasma Display status indicators

Power off

Media Receiver does not turn on or its power cord is disconnected.

The Plasma Display System is in standby mode.

The Plasma Display System turns the power on.

Media Receiver status indicators

Power off

Only the Media Receiver is in standby mode or the Plasma Display System is in standby mode.

The Plasma Display System turns the power on.

STANDBY/ON

MAIN POWER

STANDBY/ON

INPUTSTANDBY/ON VOLUMECHANNEL

Power indicator

POWER

STANDBY/ON

MEDIA RECEIVER

PDP-R03U

PUSH

PLASMA DISPLAY SYSTEM

POWER

Power indicator

TV

ANT INPUT

SURR

FRONT

AV

SELECTION

MTS CC

SPLIT

SELECT

SUB SUB CH

ⴐ

FREEZE

MODE

SCREEN

SLEEP LEARNEDIT/

DISPLAY

INPUT ⴑ

TV VCRCBL

/SAT

/DTV

DVD

/LD

123

456

789

0

CH

ENTER

Turning on the power

1 Press MAIN POWER on the Plasma Display.

• The power indicator on the Plasma Display flashes red.

2 Press POWER on the Media Receiver.

• The System turns the power on.

• The power indicators on the Plasma Display and Media

Receiver lights up green.

• If the power indicators still light up red, press TV a on

the remote control unit or STANDBY/ON on the Plasma

Display to turn the System on.

First time turning on Media Receiver

1 Press POWER on the Media Receiver.

• The power indicator on the Media Receiver lights up

red.

2 Press MAIN POWER on the Plasma Display.

• The System turns the power on.

• The power indicators on the Plasma Display and Media

Receiver lights up green.

• If the power indicators still light up red, press TV a on

the remote control unit or STANDBY/ON on the Plasma

Display to turn the System on.

A

• In this manual, “System” mean the Plasma Display Panel and

Media Receiver.

Turning off the power

1 Press TV a on the remote control unit or STANDBY/

ON on the Plasma Display.

• The System enters standby mode and the image on

the screen disappears.

• Both power indicators change from green to red.

2 Press POWER on the Media Receiver.

• The power indicator on the Media Receiver turns off

and the one on the Plasma Display flashes red.

3 Press MAIN POWER on the Plasma Display.

• The power indicator on the Plasma Display turns off

after approximately 5 seconds.

A

• If you are not going to use this System for a long time, be sure to

remove the Power cord from the power outlet.

Off

Red

Green

E-15

Watching TV

Language menu

Antenna menu

1. Setting a language

1 Press a/b to select the desired language listed

on the screen.

2 Press SET/ENTER to enter the setting.

2. Setting the antenna mode

1 Press a/b to select “Air” or “Cable” on the screen.

2 Press SET/ENTER to enter the setting.

Searching TV channels

CH Search

Air 2

Initial auto installation

When you turn on the Plasma Display System for the first time, it will automatically memorize the broadcasting

channels where you live. Perform the following steps before you press TV a.

1. Insert the batteries into the remote control unit. (See page 8.)

2. Connect the antenna cable to the Media Receiver. (See page 12.)

3. Plug in the power cord to the wall outlet. (See page 13.)

3. Automatic channel searching

Channel auto search makes the Plasma Display System

look for all channels viewable in the set area.

A

• If no channel is found, “No program found. Is antenna

connected properly?” displays. And the auto channel

search finishes.

• If you want to try auto installation again, see page 23.

• Channel search function is available for ANT-A only.

• ANT-B cannot perform channel search.

• You may need to manually add the CABLE Converter

output channel setting (fixed), when connecting the CABLE

Converter output signal to the B terminal (ANT/CABLE

75q) on the Media Receiver (Rear).(See page 25.)

Language

English

Français

Español

Air/Cable

Air

Cable

E-16

Watching TV

Simple button operations for changing

channels

Using CH

kk

k/

ll

l on the remote control unit

• Press CH

kk

k to increase channel number.

• Press CH

ll

l to decrease channel number.

A

• CHANNEL s/r on the Plasma Display operates the

same as CH

ll

l/

kk

k.

Plasma Display

Channel display

STANDBY/ON

INPUTSTANDBY/ON VOLUMECHANNEL

CHANNEL /

38

ANT-A

STEREO

Using 0 – 9 on the remote control unit

Select the channels directly by pressing buttons 0 to

9.

a

• To select channel 8, a 1-digit channel, press 8.

• To select channel 38, a 2-digit channel, press 3,

followed by 8.

• To select channel 138, a 3-digit channel, press 1,

then 3, followed by 8.

• You can tune in channels more quickly if you press

CH ENTER after pressing 0 to 9.

TV

ANT INPUT

SURR

FRONT

AV

SELECTION

MTS CC

SPLIT

SELECT

SUB SUB CH

ⴐ

ⴑ

ⴐ

ⴑ

FREEZE

MODE

CH VOL

RETURN

CH

MUTING

SCREEN

SLEEP LEARNEDIT/

DISPLAY

INPUT ⴑ

TV VCRCBL

/SAT

/DTV

DVD

/LD

123

456

789

0

CH

ENTER

Using CH RETURN on the remote control

unit

Press CH RETURN to switch the currently tuned

channel to the previously tuned channel.

Press CH RETURN again to switch back to the

currently tuned channel.

E-17

Plasma Display

Volume adjustment

Mute

* When “Audio Out” is set to “Variable”, the indicator on the

screen changes as shown below.

Output device

Variable sound

Audio out

VariableFixed

Variable sound

Constant as

specified

Mute

A

• See page 46 for details on the audio out function.

Using e MUTING on the remote control unit

e mutes the current sound output.

1 Press e MUTING.

•“M” displays on the screen for 8 minutes, muting the

sound.

• When mute mode finishes, the volume level is set to 0,

preventing the system from suddenly outputting a loud

sound.

2 Press e MUTING again to cancel the mute.

• Pressing VOL

kk

k/

ll

l and MTS (TV mode only) can also

cancel the mute.

STANDBY/ON

INPUTSTANDBY/ON VOLUMECHANNEL

VOLUME /

20

Speaker

MONITOR OUT

Simple button operations for changing

volume/sound

Using VOL

kk

k/

ll

l on the remote control unit

• To increase the volume, press VOL

kk

k.

• To decrease the volume, press VOL

ll

l.

A

• VOLUME s/r on the Plasma Display operates the same

as VOL

ll

l/

kk

k.

Audio status

Watching TV

TV

ANT INPUT

SURR

FRONT

AV

SELECTION

MTS CC

SPLIT

SELECT

SUB SUB CH

ⴐ

ⴑ

ⴐ

ⴑ

FREEZE

MODE

CH VOL

RETURN

CH

MUTING

MENU TV/SAT/DVD

DTV/DVD TOP

SOURCE DTV/SAT

RETURN

MENU

SCREEN

SLEEP LEARNEDIT/

DISPLAY

INPUT ⴑ

TV VCRCBL

/SAT

/DTV

DVD

/LD

123

456

789

0

CH

ENTER

Page is loading ...

Pioneer PDP-4330HD User manual

This manual is also suitable for

Pioneer PDP-4330HD User manual

Related papers

Other documents