Omron Healthcare Automatic Blood Pressure Monitor User manual

Brand: Omron Healthcare

Model: Automatic Blood Pressure Monitor

Category: Blood pressure units

Type: User manual

This manual is also suitable for

Instruction Manual

Automatic Digital

Blood Pressure Monitor

Model HEM-703CP

HEM-703CP-xxxx 0692581-7 A

Important

CONTENTS

Important                           1

Name and Function of Each Part         2

Preparations for Use                  3

Instructions for Use                   8

When Error Indication Symbols Appear   10

Specications                       11

Thank you for purchasing our Digital Blood

Pressure & Pulse Monitoring Kit Please care-

fully read this instruction manual before use

and keep it with your portion of the enclosed

warranty card

PLEASE NOTE:

1 Allow 3 to 5 minutes between blood pres-

sure readings on same arm Repeated

mea-surement results in inaccurate

readings

2 Keep in mind only a physician can ac-

curately determine safe or unsafe limits

of blood pressure This instrument should

be used by non-professional persons only

to determine measurement of blood pres-

sure, not to make any medical judgement

Remember, blood pressure varies during

the day

3 This unit is a precision instrument − avoid

rough handling, direct sunlight, high tem-

perature/humidity and magnetic eld

Fold-ing or bending cuff may result in

damage to cuff

4 Do not inate cuff above 280 mmHg

5 Do not take unit apart You cannot

calibrate unit If you have any difculties

or problems with unit, contact our Service

Center 1-800-634-4350

Name and Function of Each Part

Air Jack

Systolic Bood Pressure Display

Diastolic Blood Pressure and Pulse Display

Printing Paper

Paper Cutter

SPHYG/CLOCK Button

START Button

PRINT / PAPER FEED Button

SET Button

Tab

Air Plug

Air Tube

MODE Selector Button

Main Unit

Cuff

Preparations for Use

1 How to insert the batteries

Battery Cover

1 Take off the battery cover at the back of

the main unit by sliding it in the direction

indicated by the arrow symbol

Replacement

• When the “Replace Batteries” symbol

( ) ashes during measurement,

please replace the batteries with the

new ones

• When the batteries have run down,

random numbers may be displayed

Points to be careful about whan using

the batteries

• When replacing the batteries please

replace all four batteries at once

• Use the same kind of batteries

• Take out weak batteries quickly so as to

avoid causing damage to the machine

• Remove the batteries when the unit is

not used for extended periods

2 Install 4 “AA” size batteries attached so

that the + and - polarities on the

batteries correctly match the polarities in

the battery compartment

3 Replace the cover

Preparations for Use

2 How to Set Time and Date 3 Plug in and Turn on

1 When batteries are installed, the display

shows PM 12:00

1 Insert the air plug into the air jack on the

left side of the main unit correctly

2 When the SPHYG/CLOCK button is

changed to the sphygmomanometer mode,

all the LCD symbols are momentarily

displayed This happens because the unit

is running a check on the display and this

state lasts for approximately one second

3 Once the LCD symbols vanish, the air

release indication symbol (  ) starts

ashing Please wait until the (  ) symbol

goes out

4 When the preparations necessary before

measurement have been completed, the

unit emits a series of beeps and nally the

“Ready to Measure” symbol ( ♥ ) will be

displayed

2 When the MODE button

is pressed

down, the “month” sign is displayed

When the SET button is pressed down,

the gure for the month increases Adjust

the “month”

3 When the MODE button

is pressed

down after the “month” has been adjusted,

the “day” sign is displayed Adjust the

“day” in the same way as the “month”

4 In the same manner select the “hour” and

“min” with the MODE button and set

each value with the SET button  AM and

PM signs are switched in accordance with

the “hour” adjsutment

5 Press the MODE button

for the last time

and return the screen to normal time (hour,

min) display

Initial Display

“Ready to Measure”

Display

Air release

indication symbol

Preparations for Use

4 How to Set the Printing Paper

Please be sure not to print without inserting

printing paper as it will shorten the life span

of the printer head

1 Slide the plastic printer cover in the

direction indicated by the arrow symbol

and remove it from the main unit

4 Insert the printing paper in the installation

section, and then attach the cover back to

the main unit in such a way that the edge

of the paper protrudes from the cover

5 When the PRINT/PAPER FEED button

is pressed while the results of the

measurement are shown on the digital

display, these results, together with the

date and time of measurement are printed

out

6 When purchasing printing paper, ask at the

shop where you purchased the main unit

for further supply Other brands of paper

may be used providing the dimensions are

smaller than 38mm wide and 20mm in di-

ameter However the printing quality may

differ a little

2 Peel off the glued edge of the prontlng

paper included with the unit, and cut it off

to about 2 inches with a pair of scissors,

and then shape and cut the edge for easy

insertion to the printer as shown in the

gure

3 Press the PRINT/PAPER FEED button

while inserting the edge of the printing

paper to the paper feeding slit When the

edge of the paper protrudes sufciently,

release the button and stop feeding

Inserting Direction

Reverse

Front

Preparations for Use

5 Changing the Printer Ink

Though not originally equipped with an ink

roller, the HEM-703CP digital blood pressure

monitor contains enough printer ink to last

about two years when used once a day at

normal room temperature

When the ink on the print out becomes light

and hard to read, purchase a replacement ink

roller from your retailer and install as fol-lows

1 Remove the printer cover

3 Insert the supplement ink roller into the

allotted space next to the printer

4 Replace the printer cover

NOTE: The supplement ink roller should

last about two years, however, if you

need to replace the supplement ink

roller, simply grasp the top of the ink

roller and turn itslightlycounterc1ock-

wise before lifting the roller from the

printer

Supplement ink roller

2 Removethe ink, which came with the

unit when you bought it, from the allotted

space

about 1 inch

Artery

no space

Preparations for Use

6 Attach the Cuff

This cuff has eliminated the need for a

microphone thereby lessening possible

interference from vibrations and noise Fitting

also has been made much easier through the

widening of the artery oscillation detection

area

1 Place the cuff on the left arm so that the air

tube lies across the center of the arm

3 Place your arm on a table or a support with

the palm facing upward so that the cuff is

placed at the same level as the heart

2 Wrap the cuff pulling in a diagonal angle

securely so that the cuff tab is positioned

about one inch above the elbow joint of the

inner your left upper arm (Over the brachi-

al artery)

There should be no space between the

cuff and your arm

NOTE: If you have any difculties wrap-ping

cuff by yourself, we recom-mend that

you ask someone to wrap the cuff for

you

Preparations for Use

7 Apply Pressure to the Cuff

1 When you press the start button, the pump

operates and pressure is applied When

the pressure reaches 170mmHg, the

pump stops automatically

2 When the appropriate pressure has been

reached, the air is automatically released

and the value on the display window

starts to decrease After a while when the

artery oscillations are detected, the ( ♥ )

symbol starts ashing and the unit emits

a beep-ing sound simultaneously The

value shown on the display will continue

to fall

* During measurement, do not shake

the cuff or the air tube

Depress the START

button continuously

untill the cuff is inated

up to the targeted

pressure

After the cuff has

been inated,

release the START

button

Notes:

* If your systolic blood pressure is higher

than 140mmHg, the pump starts again and

the cuff will be inated up to 210mmHg

* If your systolic blood pressure is higher

than 180mmHg, sufcient ination will

not be applied to the cuff by automatic

reination In this case, inate up to

30mmHg higher than your expected

systolic blood pressure by pressing the

start button continuously While press-ing

the start button, the cuff can be in-ated

continuously, and when the start button

is released, the pump stops and the cuff

is no longer inated When the pressure

reaches 300mmHg, the cuff deates

rapidly

* When you want to stop measurememt,

press SPHYG/CLOCK button The pres-

sure will stop and the air is deated rapidly

Pressure being applied

Targetted Blood

Pressure Reached

Indicated Value Drops

Measuring

Measurement

Completed

Alternate Display

Blood Pressure

Reading Display

(for approx 3

seconds)

Pulse Reading

Display

(for approx 15

seconds)

*P: Stands for PULSE

Preparations for Use

8 Blood Pressure and Pulse are displayed

When the deation symbol begins to ash,

the residual pressure in the cuff is then

rapidly released

1 When the unit has continued to deate

to a point when the artery oscillations are

no longer detected, the unit will display

the systolic and diastolic blood pressure

values, along with a long beep, and causes

the deation indication symbol (  ) to start

ashing After this, blood pressure and the

pulse readings are displayed alter-nately

* When you wish to stop measuring during

operation, press the SPHYGICLOCK

button The pump will stop and all the cuff

pressure will be released rapidly

* When the PRINT button is pressed while

the results of the measurement are shown

on the digital display, the results will be

printed

3 Measurement of the blood pressure is

now complete The results will remain

displayed even after the cuff is taken

off If you wish to carry out repeated

measurements, repeat the operation from

Step 6

* The arm gradually becomes congested

when measurements are repeatedly

taken If you wish to take consecutive

measurements, take off the cuff and

wait at least 3 to 5 minutes between

measurements

4 When measurement is completed press

the SPHYG/CLOCK button to return to the

time display If you should forget to press

this button, the display will return to time

display mode automatically after about 5

minutes

2 Upon total cuff deation, a series of

beeps are emitted and the ( ♥ ) symbol is

displayed

When Error Indication Symbols Appear

The following special error symbols will appear in the display if the unit is being used incorrectly:

ERROR SYMBOL CAUSE CORRECTION

1 Cuff underinated 1) Release air pressure in cuff

2) Wait 10 minutes before taking

another reading

3) Repeat “Instructions for Use”

steps except inate cuff 30

mmHg higher than previous

ination value

2 Movement during

measurement

Residual air pressure

in cuff

1) Release air pressure in cuff

2) Wait 10 minutes before taking

another reading

3) Repeat “Instructions for Use”

steps

Cuff overinated (more

than 300 mmHg)

No pulse or blood

pressure reading due to:

1) Motion

2) Very weak artery

oscillation

Specications

Power Source: Battery (four type “AA” dry cell batteries) 6V 4W

Measurement Method: Oscillometric Method

Display: Liquid Crystal Digital Display

Measurement Range: Pressure: 0 ~ 280mmHg

Pulse: 40 ~ 200/minute

Accuracy: Pressure: within ± 3 mmHg

Pulse: within ± 5% reading

Pressure Detection: Capacitive Pressure Sensor

Ination: Automatic Pressure Application by a Pump

Deation and Rapid Air Release: Automatic pressure release valve

Automatic-shut-off System When the internal pressure in the unit continues

at less than 20mmHg for about 5 ~ 8 minutes, the

mode changes automatically to clock

Printer: Serial static impact printer

Operating/Temperature, Humidity: +50

F to +104°F (+10

C to +40

C) 30-85% RH

StorageiTemperature, Humidity: -4°F to 140°F (-20°C to + 60

C) 10-95% RH

Dimensions (Approx): Main Unit: 8

4” (w) X 5

8” (d) x 2

5” (h) (215

x 130x 66 mm)

Cuff: 5

2 “(w) x 18

5”(1) (140x 480 mm)

Cuff Range: For arms 9” to 13” in circumference

Weight: Main Unit: approx 20

2 oz (580 g)including

batteries

Cuff: approx 4

5 oz (125 g)

Accessories: Cuff, instruction manual,

Printing paper: 2 rolls

Optional parts: AC Adaptor

Specications subject to change without notice

This equipment generates and used radio frequency energy and if not installed and used properly,

that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio

and television reception It has been type tested and found to comply with the limits for a Class

B computing device in accordance with the specications in Subpart J of Part 15 of FCC Rules,

which are designed to provide reasonable protection against such interference in a residential

installation However, there is no guarantee that interference will not occur in a particular

installation If this equipment does cause interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

- reorient the receiving antenna

- relocate the computer with respect to the receiver

- move the computer away from the receiver

- plug the computer into a different outlet so that computer and receiver are on different

branch circuits

If necessary, the user should consult the dealer or an experienced radio/television technician

for additional suggestions The user may nd the following booklet prepared by the Fedral

Communications Commision helpful:

“How to Identify and Resolve Radio-TV Interference Problems” This booklet is available from

the US Government Printing Ofce, Washington, DC, 20402, Stock No 004-000-00345-4

LICENSED UNDER U S PAT

48294194942516489626045311324825364,46866224121284

43969764371923447138541205834435732,46724574739396

CUSTOMER SERVICE

TOLL FREE: 1-800-634-4350

Limited One Year Warranty

YOUR OMRON MODEL HEM-713C Digital Blood Pressure Monitor is warranted to be free from manufacturing

defects for a period of one year under normal use This warranty extends only to the original retail purchaser

Should repair be needed, within the warranty period, ship the unit and receipt as proof of purchase prepaid to

OMRON HEALTHCARE, INC, 300 Lakeview Parkway, Vernon Hills, Illinois 60061, together with $500 for return

shipping and insurance

We will either repair or at our option replace free of charge any parts necessary to correct defects in material

or workmanship The above warranty is complete ad exclusive The warrantor expressly disclaims liability for

incidental, special or consequential damages of any nature (Some status do not allow the exclusion or limitation of

incidental or consequential damages so the above limitation or exclusion may not apply to you)

Any implied warranties arising by operation of law shall be limited in duration to the term of this warranty (Some

states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you)

This warranty gives you specic legal rights, and you may have other rights which vary from state to state As

condition to operation of your warranty, the enclosed registration card must be completed and sent to us within 10

days from the date of purchase

Caution

Changes or modications not expressively approved by OMRON HEALTH CARE, INC could void the user’s

authority to operate this product

Note

Potential For RadiofTelevision Interference (for USA only)

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC rules

These limits are designed to provide reasonable protection against harmful interference in a residential installation

The product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications However there is no guarantee

that interierence will not occur in a particular installation If the product does cause harmful interference to radio or

television reception, which can be determined by turning the product off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the product and receiver

• Connect the product into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radiofTV technician for help

Potential For RadiofTelevision Interference (for Canada only)

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as

set out in the interferencEH:ausing equipment standard entitled “Digital Apparatus”, ICES’{)03 of the Canadian

Department of Communications

Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de

Classe B prescrites dans la norme sur Ie materiel brouilleur “Appareils Numeriques”, NMB{J03 ildictee par Ie

ministre des communications

OMRON uses recycled paper to help preserve our natural recources

Distributed by

OMRON HEALTHCARE,INC.

300 Lakeview Parkway

Vernon Hills, Illinois 60061

0692581-7 A

Omron Healthcare Automatic Blood Pressure Monitor User manual

Brand: Omron Healthcare

Model: Automatic Blood Pressure Monitor

Category: Blood pressure units

Type: User manual

This manual is also suitable for

Download PDF

report

Omron Healthcare Automatic Blood Pressure Monitor User manual

This manual is also suitable for

Omron Healthcare Automatic Blood Pressure Monitor User manual

Related papers

Other documents