HP L1740 17 User manual

User Guide

HP L1740 17” and L1940 19”

Flat Panel Monitors

Document Part Number: 372837-001

January 2005

This guide provides information on setting up the monitor,

installing drivers, using the on-screen display menu,

troubleshooting and technical specifications.

Enhanced for Accessibility

The information contained herein is subject to change without notice.

Microsoft, MS-DOS, Windows, and Windows NT are trademarks of

Microsoft Corporation in the U.S. and other countries.

Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel

Corporation in the U.S. and other countries.

Adobe, Acrobat, and Acrobat Reader are trademarks or registered

trademarks of Adobe Systems Incorporated.

The only warranties for HP products and services are set forth in the

express warranty statements accompanying such products and services.

Nothing herein should be construed as constituting an additional warranty.

HP shall not be liable for technical or editorial errors or omissions

contained herein.

This document contains proprietary information that is protected by

copyright. No part of this document may be photocopied, reproduced, or

translated to another language without the prior written consent of

Hewlett-Packard Company.

Å

WARNING: Text set off in this manner indicates that failure to

follow directions could result in bodily harm or loss of life.

Ä

CAUTION: Text set off in this manner indicates that failure to follow

directions could result in damage to equipment or loss of information.

User Guide

HP L1740 17" and L1940 19" Flat Panel Monitors

First Edition (January 2005)

Document Part Number: 372837-001

Contents

1 Product Features

2 Safety and Maintenance Guidelines

Important Safety Information. . . . . . . . . . . . . . . . . . . . . . 2–1

Maintenance Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . 2–2

Cleaning the Monitor. . . . . . . . . . . . . . . . . . . . . . . . . 2–3

Shipping the Monitor. . . . . . . . . . . . . . . . . . . . . . . . . 2–3

3 Setting Up the Monitor

Unfolding the Monitor Base. . . . . . . . . . . . . . . . . . . . . . . 3–1

Identifying Rear Panel Components . . . . . . . . . . . . . . . . 3–2

Selecting the Signal Connectors and Cables . . . . . . . 3–3

Connecting the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . 3–3

Removing the Monitor Base . . . . . . . . . . . . . . . . . . 3–10

Mounting the Monitor . . . . . . . . . . . . . . . . . . . . . . . 3–11

Locating the Rating Label . . . . . . . . . . . . . . . . . . . . 3–13

4 Operating the Monitor

Software and Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–1

The Information File . . . . . . . . . . . . . . . . . . . . . . . . . 4–1

The Image Color Matching File . . . . . . . . . . . . . . . . 4–2

Installing the .INF and .ICM Files . . . . . . . . . . . . . . . . . . 4–2

Installing from the CD. . . . . . . . . . . . . . . . . . . . . . . . 4–2

Downloading from the Worldwide Web . . . . . . . . . . 4–3

Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–4

Adjusting Monitor Settings . . . . . . . . . . . . . . . . . . . . . . . 4–5

User Guide i

Contents

Using the On-Screen Display . . . . . . . . . . . . . . . . . . 4–6

Adjusting Screen Quality. . . . . . . . . . . . . . . . . . . . . . 4–9

Optimizing Analog Video . . . . . . . . . . . . . . . . . . . . . 4–9

Identifying Monitor Conditions . . . . . . . . . . . . . . . . . . . 4–10

Sleep Timer Mode . . . . . . . . . . . . . . . . . . . . . . . . . . 4–11

sRGB Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4–12

Changing the Color Temperature . . . . . . . . . . . . . . 4–13

Installing the sRGB ICM File for Microsoft Windows

2000 and Windows XP . . . . . . . . . . . . . . . . . . . . . . 4–13

A Troubleshooting

Solving Common Problems . . . . . . . . . . . . . . . . . . . . . . . A–1

Using the Worldwide Web. . . . . . . . . . . . . . . . . . . . . . . . A–3

Preparing to call Technical Support. . . . . . . . . . . . . . . . . A–3

B Technical Specifications

L1740 Flat Panel Monitor . . . . . . . . . . . . . . . . . . . . . . . . B–1

L1940 Flat Panel Monitor . . . . . . . . . . . . . . . . . . . . . . . . B–3

Recognizing Preset Display Resolutions . . . . . . . . . . . . . B–4

Entering User Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . B–5

Energy Saver Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . B–6

C Agency Regulatory Notices

Federal Communications Commission Notice. . . . . . . . . C–1

Modifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–1

Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–2

Declaration of Conformity for Products Marked with FCC

Logo, United States Only. . . . . . . . . . . . . . . . . . . . . . . . . C–2

Canadian Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–3

Avis Canadien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–3

European Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–3

Japanese Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–4

Korean Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–4

User Guide ii

Contents

EPA Energy Star Compliance . . . . . . . . . . . . . . . . . . . . . C–4

Power Cord Set Requirements . . . . . . . . . . . . . . . . . . . . . C–5

D LCD Monitor Quality

and Pixel Policy

User Guide iii

1

Product Features

The Flat Panel Display has an active matrix, thin-film transistor

(TFT), liquid crystal display (LCD). The monitor features

include:

■ HP L1740 model, 17-inch (43.2 cm) viewable area display,

with narrow bezels.

■ HP L1940 model, 19-inch (48.3 cm) viewable area display,

with narrow bezels.

■ 1280 × 1024 native resolution, plus full-screen support for

lower resolutions.

■ Wide viewing angle to allow viewing from a sitting or

standing position, or moving side-to-side.

■ Tilt, swivel, and height adjustment capabilities.

■ Easily removable base for flexible mounting solutions.

■ Multiple video inputs supported:

❏ VGA Analog

❏ DVI signal input (available on select models)

■ VGA analog signal cable included.

■ USB 2.0 hub with one upstream (connects to the computer)

and two downstream (connects to USB devices) ports.

■ USB cable included to connect the monitor’s USB ports to

the USB connector on the computer.

User Guide 1–1

Product Features

■ Mounting feature on bottom of monitor to accept an optional

Speaker Bar accessory kit.

■ Plug and play capability if supported by your system.

■ On-Screen Display (OSD) adjustments in English, Dutch,

French, Italian, Simplified Chinese, German, and Spanish for

ease of set-up and screen optimization.

■ Software and documentation CD includes an information file

(INF), Image Color Matching file (ICM), and product

documentation.

■ Energy Saver feature for Energy Star compliance.

■ AssetControl

■ Compliant with the following regulated specifications:

❏ EPA ENERGY STAR

❏ European Union CE Directives

❏ Swedish MPR II 1990

❏ Swedish TCO

1–2 User Guide

2

Safety and Maintenance

Guidelines

Important Safety Information

A power cord is included with your monitor. If another cord is

used, use only a power source and connection appropriate for this

monitor. For information on the correct power cord set to use with

your monitor, refer to the “Power Cord Set Requirements” section

in Appendix C.

Å

WARNING: To reduce the risk of electric shock or damage to your

equipment, do not disable the power cord grounding feature. This

equipment is designed to be connected to a grounded (earthed)

power outlet that is easily accessible to the operator. The grounding

plug is an important safety feature.

Å

WARNING: For your safety, be sure that the power outlet you plug

the power cord into is easily accessible and located as close to the

equipment as possible. When you need to disconnect the power to

the equipment, unplug the power cord from the power outlet by

grasping the plug firmly. Never pull on the cord.

User Guide 2–1

Safety and Maintenance Guidelines

Ä

CAUTION: For the protection of your monitor, as well as your

computer, connect all power cords for your computer and its

peripheral devices (such as a monitor, printer, scanner) to some form

of surge protection device such as a power strip or Uninterruptible

Power Supply (UPS). Not all power strips provide surge protection;

the power strips must be specifically labeled as having this ability.

Use a power strip whose manufacturer offers a Damage Replacement

Policy so you can replace your equipment if surge protection fails.

Maintenance Guidelines

To enhance the performance and extend the life of your monitor:

■ Do not open your monitor cabinet or attempt to service this

product yourself. Adjust only those controls that are covered

in the operating instructions. If your monitor is not operating

properly or has been dropped or damaged, contact your HP

authorized dealer, reseller, or service provider.

■ Use only a power source and connection appropriate for this

monitor, as indicated on the label/back plate of the monitor.

■ Be sure the total ampere rating of the products connected to

the outlet does not exceed the current rating of the electrical

outlet, and the total ampere rating of the products connected

to the cord does not exceed the rating of the cord. Look on the

power label to determine the ampere rating (AMPS or A) for

each device.

■ Install your monitor near an outlet that you can easily reach.

Disconnect the monitor by grasping the plug firmly and

pulling it from the outlet. Never disconnect the monitor by

pulling the cord.

■ Turn your monitor off when not in use. You can substantially

increase the life expectancy of your monitor by using a screen

saver program and turning off the monitor when not in use.

2–2 User Guide

Safety and Maintenance Guidelines

■ Slots and openings in the cabinet are provided for ventilation.

These openings must not be blocked or covered. Never push

objects of any kind into cabinet slots or other openings.

■ Do not drop your monitor or place it on an unstable surface.

■ Do not allow anything to rest on the power cord. Do not walk

on the cord.

■ Keep your monitor in a well-ventilated area, away from

excessive light, heat or moisture.

■ When removing the monitor base, you must lay the monitor

face down on a soft area to prevent it from getting scratched,

defaced, or broken.

Cleaning the Monitor

1. Unplug the monitor from the wall outlet.

2. Turn off the monitor and the computer.

3. Clean the monitor plastics with a clean cloth dampened with

water.

4. Clean the monitor screen with an antistatic screen cleaner.

Ä

CAUTION: Do not use benzene, thinner, ammonia, or any other

volatile substances to clean your monitor or the screen. These

chemicals may damage the cabinet finish as well as the screen.

Shipping the Monitor

Keep the original packing box in a storage area. You may need it

later if you move or ship your monitor.

User Guide 2–3

3

Setting Up the Monitor

To set up the monitor, ensure that the power is turned off to the

monitor, computer system, and other attached devices, then

follow the steps below.

Unfolding the Monitor Base

The monitor is shipped with the base attached in a folded flat

position. To begin using the monitor, you must unfold the base

and place the monitor in an upright position.

Unfolding the Base

User Guide 3–1

Setting Up the Monitor

Identifying Rear Panel Components

Rear Panel Components

No. Component Function

1 AC power

connector

Connects the AC power cord to the monitor.

2 USB downstream

connectors

Connects optional USB devices to the monitor.

3 USB upstream

connector

Connects the USB cable to the host (computer or

another USB hub).

4 DVI connector

(available on select

models)

Connects the DVI-D signal cable to the monitor.

5 VGA connector Connects the VGA cable to the monitor.

3–2 User Guide

Setting Up the Monitor

Selecting the Signal Connectors and Cables

There are two signal input connectors:

■ VGA connector

■ DVI-D connector (available on select models)

The monitor will automatically determine which inputs have

valid video signals. The inputs can be selected through the

On-Screen Display (OSD) feature or by pressing the

+ button (to

enable VGA signal input) or the – button (to enable DVI signal

input) on the monitor front bezel.

Connecting the Monitor

Å

WARNING: To reduce the risk of electric shock or damage to your

equipment: Do not disable the power cord grounding plug. The

grounding plug is an important safety feature.

Plug the power cord into a grounded (earthed) electrical outlet that is

easily accessible at all times.

Disconnect power from the monitor by unplugging the power cord

from the electrical outlet.

Do not place anything on power cords or cables. Arrange them so

that no one may accidentally step on or trip over them. Do not pull on

a cord or cable. When unplugging from the electrical outlet, grasp

the cord by the plug.

User Guide 3–3

Setting Up the Monitor

1. Place the monitor in a convenient, well-ventilated location

near your computer.

2. Pivot the monitor to the portrait position. Connect one end of

the power cable to the power connector on the monitor 1,

and the other end to an electrical wall outlet 2.

Connecting the Power Cable

3–4 User Guide

Setting Up the Monitor

3. For analog operation, connect one end of the VGA signal

cable to the VGA connector on the monitor 1

, and the other

end to the VGA connector on the computer 2.

Connecting the VGA Signal Cable

User Guide 3–5

Setting Up the Monitor

4. Connect the USB cable to the USB upstream connector on

the monitor 1 and to a convenient USB connector on the

computer 2.

Connecting the USB Cable

3–6 User Guide

Setting Up the Monitor

5. Adjust the monitor as needed for your comfort using the

monitor’s tilt, swivel, and height adjustment capabilities.

Adjusting the Tilt

Adjusting the Swivel

User Guide 3–7

Setting Up the Monitor

Adjusting the Height

3–8 User Guide

Setting Up the Monitor

Pivoting the Monitor

Ä

CAUTION: Burn-in image damage may occur on monitors that

display the same static image on screen for a prolonged period of

time. To avoid burn-in image damage on your monitor screen, you

should always activate a screen saver application or turn off the

monitor when it is not in use for a prolonged period of time.

User Guide 3–9

Setting Up the Monitor

Removing the Monitor Base

The monitor base can be removed to mount the monitor on a wall,

a swing arm or other mounting fixture. Read the caution and

warning statements below before beginning the procedure.

Ä

CAUTION: Before beginning to disassemble the monitor, be sure the

monitor is turned off and the power and signal cables are both

disconnected.

Lay the front bezel down on a soft area to prevent it from getting

scratched, defaced, or broken

Å

WARNING: Do not remove the base from the monitor while the

monitor is in the upright position. Before removing the monitor from

the base, ensure that the monitor is lying flat, front bezel down, and

that the base is set to the maximum base extension. Attempting to

remove the monitor from the base while upright in the minimum base

extension may result in injury to the user.

1. Disconnect and remove the signal and power cables from the

back of the monitor.

Ä

CAUTION: Ensure that the bottom of the monitor base is positioned

over a table or desktop before removing the base from the monitor.

3–10 User Guide

Page is loading ...

HP L1740 17 User manual

This manual is also suitable for

HP L1740 17 User manual

Related papers

Other documents