Dell E12S Series User manual

Category
Servers
Type
User manual

This manual is also suitable for

Dell™ PowerEdge™
R510 Systems
Getting Started
With Your System
Guide de mise en route
Primeiros passos com o sistema
Procedimientos iniciales con el sistema
Dell™ PowerEdge™
R510 Systems
Getting Started
With Your System
Regulatory Model E12S Series and E13S Series
Notes, Cautions, and Warnings
NOTE: A NOTE indicates important information that helps you make better use
of your computer.
CAUTION: A CAUTION indicates potential damage to hardware or loss of data
if instructions are not followed.
WARNING: A WARNING indicates a potential for property damage,
personal injury, or death.
____________________
Information in this document is subject to change without notice.
© 2009 Dell Inc. All rights reserved.
Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.
is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Inc.;
Intel and Xeon are registered trademarks of Intel Corporation in the U.S. and other countries;
Microsoft, Hyper-V, Windows, and Windows Server are either trademarks or registered trademarks
of Microsoft Corporation in the United States and/or other countries; Red Hat and Red Hat Enterprise
Linux are registered trademarks of Red Hat, Inc. in the United States and other countries; SUSE is a
registered trademark of Novell, Inc., in the United States and other countries; VMware and vSphere
are registered trademarks or trademarks (the "Marks") of VMware, Inc. in the United States and/or
other jurisdictions; Citrix and XenServer are trademarks of Citrix Systems, Inc. and/or more of its
subsidiaries, and may be registered in the United States Patent and Trademark Office and in
other countries.
Other trademarks and trade names may be used in this document to refer to either the entities claiming
the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks
and trade names other than its own.
Regulatory Model E12S Series and E13S Series
October 2009 P/N 3YPMN Rev. A00
Getting Started With Your System 3
Installation and Configuration
WARNING: Before performing the following procedure, review the safety
instructions that came with the system.
Unpacking the System
Unpack your system and identify each item.
Assemble the rails and install the system in the rack following the safety
instructions and the rack installation instructions provided with your system.
4 Getting Started With Your System
Optional – Connecting the Keyboard, Mouse, and Monitor
Connect the keyboard, mouse, and monitor (optional).
The connectors on the back of your system have icons indicating which cable
to plug into each connector. Be sure to tighten the screws (if any) on the
monitor's cable connector.
Connecting the Power Cable(s)
Connect the system’s power cable(s) to the system and, if a monitor is used,
connect the monitor’s power cable to the monitor.
Getting Started With Your System 5
Securing the Power Cable(s)
Bend the system power cable into a loop as shown in the illustration and secure
the cable to the bracket using the provided strap. Plug the other end of the
power cable into a grounded electrical outlet or a separate power source such
as an uninterrupted power supply (UPS) or a power distribution unit (PDU).
Turning On the System
Press the power button on the system and the monitor. The power indicators
should light.
6 Getting Started With Your System
Installing the Optional Bezel
Install the bezel (optional).
Complete the Operating System Setup
If you purchased a preinstalled operating system, see the operating system
documentation that ships with your system. To install an operating system
for the first time, see the installation and configuration documentation
for your operating system. Be sure the operating system is installed before
installing hardware or software not purchased with the system.
Supported Operating Systems
NOTE: For twelve–hard-drive systems with additional internal hard drives,
it is recommended that you install the operating system on the internal hard drives
in a RAID 1 configuration.
Microsoft
®
Windows Server
®
2008 Hyper-V™ Standard (x64) Edition
Microsoft Windows
®
Small Business Server 2008 Standard
and Premium (x64) Editions
Microsoft Windows Essential Business Server 2008
Premium (x86) Edition
Microsoft Windows Essential Business Server 2008 Standard
and Premium (x64) Editions
body.fm Page 6 Tuesday, October 20, 2009 10:43 AM
Getting Started With Your System 7
body.fm Page 7 Tuesday, October 20, 2009 10:44 AM
Microsoft Windows Server 2008 Standard, Enterprise, and
Datacenter (x64) Editions with SP2 with Hyper-V role enabled
Microsoft Windows Web Server 2008 with SP2 with Hyper-V role enabled
Microsoft Windows Server 2008 Standard and Enterprise (x86) Editions
with SP2
Microsoft Windows Web Server 2008 with SP2
Microsoft Windows Server 2008 R2 Standard, Enterprise,
and Datacenter (x64) Editions with Hyper-V role enabled
Microsoft Windows Web Server 2008 R2 with Hyper-V role enabled
Microsoft Windows HPC Server 2008 R2 (x64) Edition
Microsoft Windows Server 2003 R2 Standard and Enterprise (x86)
Editions with SP2
Microsoft Windows HPC Server 2008 (x64) Edition
NOTE: Not supported on twelve–hard-drive systems.
Microsoft Windows Server 2003 R2 Standard, Enterprise,
and Datacenter (x64) Editions with SP2
•Red Hat
®
Enterprise Linux
®
AS and ES (Version 4.8) (x86_64)
•Red Hat
Enterprise Linux AS and ES (Version 4.8) (x86)
Red Hat Enterprise Linux Server 5.3 (x86_64)
Red Hat Enterprise Linux Server 5.3 (x86)
•SUSE
®
Linux Enterprise Server 10 (x86_64) with SP3
SUSE Linux Enterprise Server 11 (x86_64)
•VMware
®
vSphere™ ESXi Version 4.0
8 Getting Started With Your System
VMware Virtual Infrastructure 3 ESXi Version 3.5 Update 4
NOTE: VMware Virtual Infrastructure 3 ESXi Version 3.5 Update 4
is not supported on twelve–hard-drive systems.
Citrix
®
XenServer™ Enterprise (Version 5.5)
NOTE: Twelve–hard-drive systems support Citrix XenServer Enterprise
(Version 6.0).
Citrix Essentials for XenServer Enterprise (Version 5.5)
NOTE: For the latest information on supported operating systems,
see support.dell.com.
Other Information You May Need
WARNING: See the safety and regulatory information that shipped with
your system. Warranty information may be included within this document
or as a separate document.
The rack documentation included with your rack solution describes
how to install your system into a rack.
•The
Hardware Owner’s Manual
provides information about system
features and describes how to troubleshoot the system and install or
replace system components. This document is available online at
support.dell.com/manuals
.
Any media that ships with your system that provides documentation
and tools for configuring and managing your system, including those
pertaining to the operating system, system management software,
system updates, and system components that you purchased
with your system.
NOTE: Always check for updates on support.dell.com/manuals and read the
updates first because they often supersede information in other documents.
Obtaining Technical Assistance
If you do not understand a procedure in this guide or if the system does
not perform as expected, see your Hardware Owner’s Manual. Dell™ offers
comprehensive hardware training and certification. See www.dell.com/training
for more information. This service may not be offered in all locations.
Getting Started With Your System 9
Technical Specifications
Processor
Processor type Two Intel
®
Xeon
®
processors 5500 series
Expansion Bus
Bus type PCI Express Generation 2
Expansion slots using riser cards
NOTE: Depending on the configuration, your system may have either riser 1 or riser 2.
Riser 1
OR
Riser 2
Slot 1: PCIe x4, half-length, full-height
Slot 2: PCIe x4, full-length, full-height
Slot 3: PCIe x8, half-length, full-height
Slot 4: PCIe x4, internal slot for integrated card
NOTE: All four slots are x8 connectors.
Slot 1: PCIe x16, full-length, full-height
Slot 2: PCIe x4, internal for integrated card
NOTE: A General Purpose Computation on
Graphics Processing Units (GPGPU) optimized
configuration is available on riser 2.
Memory
Architecture 1066 or 1333 MHz DDR3 registered or
unbuffered Error Correcting Code (ECC)
DIMMs
Memory module sockets Eight 240-pin
Memory module capacities
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
1 GB, 2 GB, or 4 GB
1 GB, 2 GB, 4 GB, or 8 GB
1 GB, 2 GB, 4 GB, or 8 GB
Minimum RAM 1 GB with a single processor
(1 DIMM per processor)
Maximum RAM
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
32 GB
64 GB (8 GB dual- and quad-rank DIMMs)
64 GB (8 GB dual- and quad-rank DIMMs)
10 Getting Started With Your System
Drives
Hard drives
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
Up to four 3.5-inch, cabled SAS, SATA,
or SSD drives
Up to eight 3.5-inch or 2.5-inch,
hot-swappable SAS, SATA, or SSD drives
Up to twelve 3.5-inch or 2.5-inch,
hot-swappable SAS, SATA, or SSD drives and
up to two cabled 2.5-inch SAS or SSD drives
NOTE: For twelve–hard-drive systems
with additional internal hard drives, it is
recommended that you install the operating
system on the internal hard drives in a RAID 1
configuration.
Optical drive Optional internal slim-line SATA DVD-ROM
or DVD+/-RW
Optional external USB DVD-ROM
NOTE: Twelve–hard-drive systems support
only an external USB DVD-ROM.
Diskette drive Optional external USB 1.44-MB
Connectors
Back
NIC
Two RJ-45 (for integrated 1-GB NICs)
Serial
9-pin, DTE, 16550-compatible
USB
Two 4-pin, USB 2.0-compliant
Video
15-pin VGA
Front
Video
15-pin VGA
USB
Two 4-pin, USB 2.0-compliant
Internal
USB
Two 4-pin, USB 2.0-compliant
body.fm Page 10 Tuesday, October 20, 2009 10:46 AM
Getting Started With Your System 11
Video
Video type Matrox G200, integrated in the BMC
Video memory 8 MB
Power
AC power supply (per power supply)
Wattage
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
480 W (non-redundant power supply)
750 W/1100 W (optional redundant
power supply)
750 W (optional redundant power supply)
Voltage
100–240 VAC, autoranging, 50–60 Hz
Heat dissipation
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
1840 BTU/hr maximum
2200 BTU/hr maximum
2450 BTU/hr maximum
Maximum inrush current
Under typical line conditions and over
the entire system ambient operating range,
the inrush current may reach 55 A per
power supply for 10 ms or less.
Batteries
System battery
CR 2032 3.0-V lithium ion coin cell
Physical
Height
Four– and eight– hard-drive
systems
Twelve–hard-drive systems
8.64 cm (3.4 in)
8.67 cm (3.42 in)
Width
Four– and eight–hard-drive
systems
Twelve–hard-drive systems
43.66 cm (17.19 in)
44.52 cm (17.53 in)
12 Getting Started With Your System
Depth
Four– and eight–hard-drive
systems
Twelve–hard-drive systems
61.02 cm (24.09 in)
66.46 cm (26.17 in)
Weight (maximum configuration)
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
16 kg (35.2 lbs)
22.5 kg (49.5 lbs)
29.0 kg (63.8 lbs)
Weight (empty)
Four–hard-drive systems
Eight–hard-drive systems
Twelve–hard-drive systems
13.6 kg (29.92 lbs)
13.5 kg (29.7 lbs)
15.85 kg (34.87 lbs)
Environmental
NOTE: For additional information about environmental measurements for specific
system configurations, see www.dell.com/environmental_datasheets.
Temperature
Operating
10° to 35°C (50° to 95°F) with a maximum
temperature gradation of 10°C per hour
NOTE: For altitudes above 2950 feet,
the maximum operating temperature
is derated 1ºF/550 ft.
Storage
–40° to 65°C (–40° to 149°F) with
a maximum temperature gradation
of 20°C per hour
Relative humidity
Operating
20% to 80% (noncondensing) with
a maximum humidity gradation
of 10% per hour
Storage
5% to 95% (noncondensing)
Physical (continued)
Getting Started With Your System 13
Maximum vibration
Operating
0.26 G at 5–350 Hz for 15 min
Storage
1.54 G at 10–250 Hz for 15 min
Maximum shock
Operating
One shock pulse in the positive z axis
(one pulse on each side of the system) of
31 G for 2.6 ms in the operational orientation
Storage
Six consecutively executed shock pulses
in the positive and negative x, y, and z axes
(one pulse on each side of the system)
of 71 G for up to 2 ms
Altitude
Operating
–16 to 3.048 m (–50 to 10,000 ft)
NOTE: For altitudes above 2950 feet,
the maximum operating temperature
is derated 1ºF/550 ft.
Storage
–16 to 10,600 m (–50 to 35,000 ft)
Airborne Contaminant Level
Class
G2 or lower as defined by ISA-S71.04-1985
Environmental (continued)
14 Getting Started With Your System
Guide de mise en route 21
body.fm Page 21 Tuesday, October 20, 2009 11:44 AM
Microsoft Windows Server 2008, Éditions Standard, Enterprise
et Datacenter (x64) SP2 avec rôle Hyper-V acti
Microsoft Windows Web Server 2008 SP2 avec rôle Hyper-V activé
Microsoft® Windows Server 2008, Éditions Standard et Enterprise
(x86) SP2
Microsoft Windows Web Server 2008 SP2
Microsoft Windows Server 2008 R2, Éditions Standard, Enterprise
et Datacenter (x64) avec rôle Hyper-V activé
Microsoft Windows Web Server 2008 R2 avec rôle Hyper-V activé
Microsoft Windows HPC Server 2008 R2 (x64)
Microsoft Windows Server 2003 R2, Éditions Standard et Enterprise
(x86) SP2
Microsoft Windows HPC Server 2008 (x64)
REMARQUE : Non pris en charge sur les systèmes à douze disques durs.
Microsoft Windows Server 2003 R2, Éditions Standard, Enterprise
et Datacenter (x64) SP2
•Red Hat
®
Enterprise Linux
®
AS et ES (Version 4.8) (x86_64)
•Red Hat
Enterprise Linux AS et ES (Version 4.8) (x86)
Red Hat Enterprise Linux Server 5.3 (x86_64)
Red Hat Enterprise Linux Server 5.3 (x86)
•SUSE
®
Linux Enterprise Server 10 (x86_64) avec SP3
SUSE Linux Enterprise Server 11 (x86_64)
•VMware
®
vSphere™ ESXi Version 4.0
VMware Virtual Infrastructure 3 ESXi Version 3.5 Update 4
REMARQUE : VMware Virtual Infrastructure 3 ESXi Version 3.5 Update 4
n'est pas pris en charge sur les systèmes à douze disques durs.
Primeiros passos com o sistema 35
Microsoft Windows Server 2008, edições Standard, Enterprise e
Datacenter (x64) com SP2 e a função Hyper-V ativada
Microsoft Windows Web Server 2008 com SP2 e a função Hyper-V ativada
Microsoft Windows Server 2008, edições Standard e Enterprise (x86)
com SP2
Microsoft Windows Web Server 2008 com SP2
Microsoft Windows Server 2008 R2, edições Standard, Enterprise
e Datacenter (x64) com a função Hyper-V ativada
Microsoft Windows Web Server 2008 R2 com a função Hyper-V ativada
Microsoft Windows HPC Server, edição 2008 R2 (x64)
Microsoft
®
Windows Server 2003 R2, edições Standard e Enterprise (x86)
com SP2
Microsoft Windows HPC Server, edição 2008 (x64)
NOTA: Não há suporte sistemas de disco rígido de 12.
Microsoft Windows Server 2003 R2, edições Standard, Enterprise
e DataCenter (x64) com SP2
•Red Hat
®
Enterprise Linux
®
AS e ES (versão 4.8) (x86_64)
•Red Hat
Enterprise Linux AS e ES (versão 4.8) (x86_32)
Red Hat Enterprise Linux Server 5.3 (x86_64)
Red Hat Enterprise Linux Server 5.3 (x86)
•SUSE
®
Linux Enterprise Server 10 (x86_64) com SP3
SUSE Linux Enterprise Server 11 (x86_64)
•VMware
®
vSphere™ ESXi versão 4.0
VMware Virtual Infrastructure 3 ESXi versão 3.5 Atualização 4
NOTA: Não há suporte para VMware Virtual Infrastructure 3 ESXi versão 3.5
Atualização 4 em sistemas de disco rígido de 12.
Procedimientos iniciales con el sistema 49
Microsoft Windows Essential Business Server 2008 Standard y Premium
(x64) Edition
Microsoft Windows Server 2008 Standard, Enterprise y Datacenter (x64)
Edition con SP2 y la función Hyper-V habilitada
Microsoft Windows Web Server 2008 con SP2 y la función Hyper-V
habilitada
Microsoft Windows Server 2008 Standard y Enterprise (x86) Edition
con SP2
Microsoft Windows Web Server 2008 con SP2
Microsoft Windows Server 2008 R2 Standard, Enterprise y Datacenter
(x64) Edition con la función Hyper-V habilitada
Microsoft Windows Web Server 2008 R2 con la función Hyper-V
habilitada
Microsoft Windows HPC Server 2008 R2 (x64) Edition
Microsoft Windows Server 2003 R2 Standard y Enterprise (x86) Edition
con SP2
Microsoft Windows HPC Server 2008 (x64) Edition
NOTA: No se admite en sistemas con doce unidades de disco duro.
Microsoft Windows Server 2003 R2 Standard, Enterprise y Datacenter
(x64) Edition con SP2
•Red Hat
®
Enterprise Linux
®
AS y ES (versión 4.8) (x86_64)
•Red Hat
Enterprise Linux AS y ES (versión 4.8) (x86)
Red Hat Enterprise Linux Server 5.3 (x86_64)
Red Hat Enterprise Linux Server 5.3 (x86)
•SUSE
®
Linux Enterprise Server 10 (x86_64) con SP3
SUSE Linux Enterprise Server 11 (x86_64)
•VMware
®
vSphere™ ESXi versión 4.0
VMware Virtual Infrastructure 3 ESXi versión 3.5 actualización 4
NOTA: VMware Virtual Infrastructure 3 ESXi versión 3.5 actualización 4
no se admite en sistemas con doce unidades de disco duro.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

Dell E12S Series User manual

Category
Servers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI