Sharp HT-SL75 User manual

Sharp
Brand
Sharp
Model
HT-SL75
Category
Supplementary music equipment
Type
User manual

This manual is also suitable for

HT-SL70_75_Front ZB042EN.fm
2011September20
Notes:
● This product is recommended for flat panel TV (LCD and plasma).
● For HDMI connection, this product only supports PCM (Pulse Code Modulation) signals.
● This product is controlled via HDMI CEC (Consumer Electronics Control) specification, therefore
for HDMI connection, your TV’s CEC must be enabled. For detail, refer to the operation manual of the TV.
● For TV without HDMI CEC, headphone or RCA (variable output) analogue connection is available.
● For TV without HDMI, headphone or RCA (variable output) connection is required.
● This unit supports HDMI which enables Audio Return Channel (ARC).
Recommended Connection:
TV Type CEC FUNCTION CONNECTION CONNECTION METHOD
HDMI
( with ARC)
MUST BE ENABLED
HDMI IN
(ARC)
Page 11, Method 1
with HDMI MUST BE ENABLED HDMI IN Page 11, Method 2
HDMI TV without
CEC & ARC or non
HDMI TV
NONE
HEADPHONE OUT Page 12, Method 1
RCA
(VARIABLE OUT)
Page 12, Method 2
OPERATION MANUAL
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read
this manual carefully. It will guide you in operating your SHARP product.
TINSZB042AWZZ
Printed in Malaysia
11K R MW 1
MODEL
HT-SL70 / HT-SL75
SOUND BAR HOME THEATER SYSTEM
ENGLISH
HT-SL70 and HT-SL75 Sound Bar Home Theater system consisting of Sound Bar and Subwoofer.
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-1
2011 October 7
The following accessories are included. This product has no remote control.
For HT-SL75 only.
For HT-SL70 only.
The illustrations printed in this operation manual are for the model HT-SL70.
Accessories
RCA to Headphone
Cable (1pin - 2 pins) x 1
(QCNWGA064AWPZ)
Subwoofer Stand x 2
(GITAUA004AW01)
Audio Cable x 1
(QCNWGA062AWPZ)
HDMI Cable x 1
(QCNWGA065AWPZ)
Wall Mount
Bracket x 2
(LHLDZA267AWSA)
Wall Mount
Angle x 2
(LANGKA225AW01)
Pattern Paper
For HT-SL75 only:
(TCAUHA028AWZZ)
For HT-SL70 only:
(TCAUHA027AWZZ)
Speaker Wire
For HT-SL75 only:
(QCNWHA046AW01)
For HT-SL70 only:
(QCNWHA043AW01)
Sound Bar Stand x 2
(GITAUA012AW01)
Screw for
Brackets x 6
(XEBY830P08000)
Sound Bar Stand
Cushion x 2
(PCUSSA190AWZZ)
Sound Bar Cover Joint
for 60" TV (short) x 1
(GCOVAA331AW01)
Sound Bar Cover Joint
for 70" TV (long) x 1
(GCOVAA333AW01)
Stand Cover x 2
(GCOVAA330AW01)
Stand Base x 2
(GDAI-A016AW01)
SO
U
N
D
B
A
R
H
O
M
E
T
H
E
A
T
E
R
S
Y
S
T
E
M
H
T
-
SL
7
5
14 - 17/32"
(369 mm)
S
O
U
N
D
B
A
R
H
O
M
E
T
H
E
A
T
E
R
S
Y
ST
E
M
H
T
-
S
L
7
5
23 - 3/8"
(594 mm)
10 - 2/16" (257 mm)
13 - 7/32" (336 mm)
Sound Bar Cover Joint
for 46" TV (short) x 1
(GCOVAA300AW01)
Sound Bar Cover Joint
for 52" TV (long) x 1
(GCOVAA302AW01)
Stand Cover x 2
(GCOVAA306AW01)
Stand Base x 2
(GDAI-A013AW01)
S
O
U
N
D
BA
R
H
O
M
E
T
H
E
A
T
E
R S
YS
T
E
M
H
T
-
S
L
7
0
2 - 5/
32"
(
55 mm)
S
O
U
N
D
B
A
R
H
O
M
E
T
H
EA
T
E
R
S
Y
S
T
E
M
H
T
-
S
L
7
0
7 - 13/32"
(188 mm)
6 - 3/32"
(155 mm)
6 - 15/16"
(
176 mm)
E-2
2011 October 7
HT-SL70 / HT-SL75 ZB042
NOTE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV
technician for help.
WARNING
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by
the manufacturer could void the user’s authority to operate
this equipment.
Special Notes
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
Explanation of Graphical Symbols:
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
FOR YOUR RECORDS
For your assistance in reporting this unit in case of loss
or theft, please record below the model number and
serial number which are located on the rear of the unit.
Please retain this information.
Model number ........................................................
Serial number ........................................................
Date of purchase ........................................................
Place of purchase ........................................................
HDMI, the HDMI Logo, and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other
countries.
ENERGY STAR
®
Prog
ram Information
Products that have earned
the ENERGY
STAR
®
are
de
s
ig
ned to protect the
environment throu
gh
s
uperior ener
g
y efficiency.
ENERGY
STAR
®
i
s a U.
S. registered mark.
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-3
2011 October 7
Electricity is used to perform many useful functions, but it
can also cause personal injuries and property damage if
improperly handled. This product has been engineered
and manufactured with the highest priority on safety.
However, improper use can result in electric shock and/or
fire. In order to prevent potential danger, please observe
the following instructions when installing, operating and
cleaning the product. To ensure your safety and prolong
the service life of this product, please read the following
precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Additional Safety Information
15) Power Sources - This product should be operated
only from the type of power source indicated on the
marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or
local power company. For product intended to operate
from battery power, or other sources, refer to the
operating instructions.
16) Overloading - Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can
result in a risk of fire or electric shock.
17) Object and Liquid Entry - Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the product.
18) Damage Requiring Service - Unplug this product from
the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen
into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as an improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in
any way, and
f) When the product exhibits a distinct change in
performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
20) Safety Check - Upon completion of any service or
repairs to this product, ask the service technician to
perform safety checks to determine that the product is
in proper operating condition.
21) Wall or ceiling mounting - When mounting the product
on a wall or ceiling, be sure to install the product
according to the method recommended by the
manufacturer.
22) Power Lines - An outside antenna system should not
be located in the vicinity of overhead power lines or
other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an
outside antenna system, extreme care should be
taken to keep from touching such power lines or
circuits as contact with them might be fatal.
23) Protective Attachment Plug - The product is equipped
with an attachment plug having overload protection.
This is a safety feature. See Instruction Manual for
replacement or resetting of protective device. If
replacement of the plug is required, be sure the
service technician has used a replacement plug
specified by the manufacturer that has the same
overload protection as the original plug.
24) Stand - Do not place the product on an unstable cart,
stand, tripod or table. Placing the product on an
unstable base can cause the product to fall, resulting
in serious personal injuries as well as damage to the
product. Use only a cart, stand, tripod, bracket or table
recommended by the manufacturer or sold with the
product. When mounting the product on a wall, be
sure to follow the manufacturer
’
s instructions. Use
only the mounting hardware recommended by the
manufacturer.
Important Safety Instructions
12) Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.
E-4
2011 October 7
HT-SL70 / HT-SL75 ZB042
For U.S customer only
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the
"Product"), when ship in its original container, will be free from defective workmanship and materials, and agrees that it will,
at its option, either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent
at no charge to the purchaser for part
s or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below
nor to any Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or
other misuse, abnormal service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warra
nty, the purchaser should follow the steps set forth below and provide
proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law.
ALL IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE
LIMITED TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow
limitations on how long an implied warranty las
ts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those
described herein, or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive wa
rranties granted by Sharp and shall be the sole and
exclusive remedy available to the purchaser. Correction of defects, in the manner and for the period of time described
herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the
Product, and shall constitute full sa
tisfaction of all claims, whether based on contract, negligence, strict liability or otherwise.
In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused
by repairs or attempted repairs performed by anyone other than an authorized servicer. Nor shall Sharp be liable or in any
way respon
sible for any incidental or consequential economic or property damage. Some states do not allow the exclusion
of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY
FROM STATE TO STATE.
Model Specific Section
Your Product Model Number & Description:
Warranty Period for this Product:
Additional Item(s) Excluded from Warranty Coverage
(if any):
Where to Obtain Service:
What to do to Obtain Service:
HT-SL70 / HT-
SL75 Sound Bar Home Theater System
(Be sure to have this information available when you need
service for your Product.)
One (1) year parts and labor from the date of purchase.
Non-functional accessories, supplies, and consumable
items.
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest S
harp Authorized Servicer,
call Sharp toll free at 1-800-BE-SHARP.
Ship prepaid or carry in your Product to a Sharp Authorized
Servicer. Be sure to have Proof of Purchase available. If
you ship the Product, be sure it is insured and packaged
securely.
TO OBTAIN SUPPLY, ACCESSORY OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495-1163
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-5
2011 October 7
● Use the unit on a firm, level surface free from vibration.
● Keep the unit away from direct sunlight, strong
magnetic fields, excessive dust, humidity and
electronic/electrical equipment (home computers, fax
machines, etc.) which generate electrical noise.
● Do not place anything on top of the system.
● Do not expose the unit to moisture, to temperatures
higher than 140°F (60°C) or to extremely low
temperatures.
● If your system does not work properly, disconnect the
AC power cord from the AC outlet and replug.
● In case of an electrical storm, unplug the unit for safety.
● Hold the AC power plug by the head when removing it
from the AC outlet, as pulling the cord can damage
internal wires.
● The AC power plug is used as a disconnect device and
shall always remain readily operable.
● Do not remove the outer cover, as this may result in
electric shock. Refer internal service to your local
SHARP service facility.
● This unit should only be used within the range of
41°F - 95°F (5°C - 35°C).
Warnings:
● The voltage used must be the same as that specified on
this unit. Using this product with a higher voltage other
than that which is specified is dangerous and may
result in a fire or other type of accident causing
damage. SHARP will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
● To prevent fire or shock hazard, do not expose this
appliance to dripping or splashing. No object filled with
liquids, such as vases shall be placed on the apparatus.
Precautions
● Please ensure that the equipment is positioned in a
well-ventilated area and ensure that there is at least
4" (10 cm) of free space along the sides, top and
back of the equipment.
General
ACTIVE SUBWOOFER SYSTEM
HT-SL70
4" (10 cm)
4" (10 cm)
4" (10 cm)
4" (10 cm)
E-6
2011 October 7
HT-SL70 / HT-SL75 ZB042
1. Left Front Speaker
2. Right Front Speaker
3. Bass Reflex Duct
Reference page
4. Right Front Speaker Terminal (Red/Black) . . . . 10
5. Left Front Speaker Terminal (White/Black) . . . . 10
Reference page
1. Stand-by Indicator
2. Bass Reflect Duct
3. Woofer
4. HDMI (TV ARC) Output Terminal . . . . . . . . . . . . . 11
Reference page
5. HDMI Input Terminal . . . . . . . . . . . . . . . . . . . . . . 11
6. AC Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. Speaker Terminal. . . . . . . . . . . . . . . . . . . . . . . . . 10
8. Audio In (TV) Terminal . . . . . . . . . . . . . . . . . . . . 12
Controls and indicators
Sound bar
R
L
Subwoofer
8
7
2
3
6
5
4
ACTIVE SUBWOOFER SYSTEM
HT-SL70
1
SOUND BAR HOME THEATER SYSTEM
MODEL NO.
HT-SL70
AC 120V 60Hz 40W
MADE IN MALAYSIA
FABRIQUÉ IN MALAISIE
SERIAL NO.
TSPC-B476AWZZ
FRONT VIEW
REAR VIEW
The spec label illustration
may be different from the
actual label used.
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-7
2011 October 7
Select from three installation methods according to the
preferred position.
For 52", 60" or 70" TV sound bar assembly
1. Pull out both joint covers as below.
2. Place the two sound bars near to each other and slot in
the sound bar joint and its covers as below.
For 46" TV sound bar assembly
1. Pull out the joint cover as below.
2. Place the two sound bars adjacent to each other and
slot in the sound bar joint and its cover as below.
To fix the sound bar stand
1. Peel off the double sided tape separator and attach the
sound bar stand cushion at the bottom surface of the
sound bar stand.
2. Fix the sound bar stand as shown.
System preparation
Make sure to unplug the AC power cord before
installing the unit or changing the position.
For model
HT-SL75
Use Sound bar cover joint (short : 369 mm)
for 60" TV.
Use Sound bar cover joint (long : 594 mm)
for 70" TV.
For model
HT-SL70
Use Sound bar cover joint (long : 188 mm)
for 52" TV.
For model
HT-SL70
Use Sound bar cover joint (short : 55 mm)
for 46" TV.
1. Using stand (horizontal arrangement)
Sound bar joint
Cover
S
O
U
N
D
B
A
R
H
O
M
E T
H
E
AT
E
R
S
Y
S
T
E
M
HT-
S
L
7
0
Front side of
the sound bar
Right
Left
SOUND BAR HOME THEATER SYSTEM HT-SL70
SOUND BAR HOME THEATER SYSTEM HT-SL70
Sound bar joint (short)
Cover
S
O
U
N
D
BA
R
H
O
M
E
T
H
E
AT
E
R
S
Y
S
T
E
M
H
T-S
L
7
0
Front side of
the sound bar
Right
Left
Sound bar stand cushion
Double
sided
tape
separator
Sound bar
stand
Hook
Note:
Sound bar stand can be removed
by pulling it off backward from
the sound bar.
Suggestion of the
sound bars and
LCD TV horizontal
arrangement.
E-8
2011 October 7
HT-SL70 / HT-SL75 ZB042
1. Pull out the cover of sound bar stand as below.
2. Slot in the sound bar into the sound bar stand and fix its
cover as shown.
3. Slot in the sound bar to the base stand according to your
TV size.
1. Fix the brackets to the holes as shown.
System preparation (continued)
For model
HT-SL75
Use sound bar stand cover : 10 - 2/16" (257 mm).
Use stand base : 13 - 7/32" (336 mm).
For model
HT-SL70
Use sound bar stand cover : 6 - 3/32" (155 mm).
Use stand base : 6 - 15/16" (176 mm).
2. Using stand (vertical arrangement)
Sound bar
stand cover
Cover
13 - 7/32"
(336 mm)
6 - 15/16"
(
176 mm)
46" TV
60" TV
Groove to
neatly arrange
the wire in.
(For model HT-SL75)
(For model HT-SL70)
52" TV
70" TV
Groove to
neatly
arrange the
wire in.
Slot in the wire inside the
groove or slit for better
wire arrangement.
Suggestion of the
sound bars and
LCD TV arrangement.
3. To mount the sound bar on the wall
LEFT
RIGHT
(Model HT-SL75 : for 60" and 70" TV)
(Model HT-SL70 : for 52" TV)
LEFT
RIGHT
(Model HT-SL70 : for 46" TV)
Caution:
Be careful not to
fix the bracket
upside down.
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-9
2011 October 7
Caution:
● Be very careful to prevent the sound bar from falling when
mounting on the wall.
● Before mounting, check the wall strength. (Do not put
on the veneer plaster or whitewashed wall. The sound
bar may fall.) If unsure, consult a qualified service
technician.
● Mounting screws are not supplied. Use appropriate
ones.
● Check all wall mount angle screws for looseness.
● Select a good location. If not, accidents may occur or
the sound bar may get damaged.
● SHARP is not responsible for accidents resulting
from improper installation.
● Do not let children dangle on the sound bar once it is
attached on the wall as it can cause damage and injury.
SHARP designed the sound bar so you may hang them on
the wall. Use proper screws (not supplied). See below for
size and type.
Note:
Make sure all screws are fully tightened. (screws are not
supplied)
Safety wires (not supplied) are useful to prevent the sound
bar from falling off the table.
Loop the safety wires (not supplied) into each hole as
shown and tie the safety wires to the LCD TV stand.
System preparation (continued)
1 Fix the pattern paper to the wall in horizontal
position as below.
2 Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
3 Fix a wall mount plug (not supplied) into the hole
using a hammer, until it is flush with the wall
surface.
Driving screws
1/8" (3.2 mm)
3/8" (9 mm)
7/8" (Min. 22 mm)
3/16"
(5 mm)
Fixing wall mount angle
Pattern paper
Wall surface
Wall surface
3/8" (8-9 mm)
1-1/4" (32 mm)
Wall surface
3/8" (8-9 mm)
1-1/4" (32 mm)
4 Screw the wall mount angle to the wall as shown in
the illustration. (Total screw is 4 pieces)
1 Align the wall mount slot at the sound bar to the
wall mount angle.
2 Slot the sound bar into the wall mount angle.
3 Fix them securely.
Wall surface
Wall mount angle
Wall
mount
angle
(screws x 2)
(screws x 2)
Installing the sound bar
Wall surface
Falling prevention
E-10
2011 October 7
HT-SL70 / HT-SL75 ZB042
Installation image:
Place the system as shown.
Remove the protective film covering the sound bar and
subwoofer before using the system.
Notes:
● As the sound from the system is omni-directional, you
can place the speaker anywhere you like. However, it is
recommended to place it as close to the TV as possible.
● The front panel of the speaker is not removable.
Caution:
Do not change the installation direction when the unit is
turned on.
Placing the system
ACTIVE SUBWOOFER SYSTEM
HT-SL70
TV
BD Player
DVD player
Place the stand as shown.
Placing the stand
ACTIVE SUB
W
OOFER SYSTEM
HT
-
SL70
SUBWOOFER SYSTEM
ACTIVE SUBWOOFER SYSTEM
HT-SL70
Stand
Make sure to unplug the AC power cord before making any connections.
System connections
R
L
Subwoofer
Sound Bar
Right
AC outlet
AC 120 V ~ 60 Hz
Left
White
Red
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
Speaker connection
Connect the wire without insulation tube to the minus (–)
terminal, and the wire with red and white insulation tube to
the plus (+) terminal.
Caution:
● Use speaker with an impedance of 3 ohms or more, as
lower impedance speaker can damage the unit.
● Do not make a mistake when
connecting the right and left
speakers. The right speaker is the
one on the right side when you face
the unit.
● Do not let the bare speaker wires
touch each other.
● Do not allow any objects to fall into or
to be placed in the bass reflex duct.
● Do not stand or sit on the subwoofer/sound bar. You
may be injured.
INCORRECT
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-11
2011 October 7
Notes:
●
This unit supports HDMI which enables ARC (Audio Return Channel).
●
To enable ARC make sure to use High Speed HDMI
™
cable (with ARC).
●
This ARC feature requires TV that supports ARC. Refer the operation manual of the TV to determine which terminal supports ARC.
●
To listen to the sound from a non-ARC-compatible TV, connect the audio output from TV to this system’s AUDIO IN (TV)
terminal. (refer page 12)
●
This unit can be operated (power on/off or volume up/down) via a TV or similar component which supports HDMI CEC
(Consumer Electronics Control). If this does not work, it does not mean this system is faulty. Refer to the operation manual
of the respective component on how to activate the CEC.
Example: Go to the Menu of the component to search and enable the CEC. Different brands may have different naming for
the CEC. For Sharp LCD TV, it is named as AQUOS LINK.
●
To listen to the sound from this system, you will need to adjust settings within the TV menu.
For details, refer to the operation manual of the TV.
●
If you are unable to select external speaker setting from the TV menu (E.g. For Sharp LCD TV, it is named as AQUOS AUDIO
SP), turn the CEC OFF and ON again.
●
Make sure the LCD TV Audio output setting is set to PCM, not other formats such as Dolby Digital, DTS, etc.
●
To enjoy 3D images, this system must be connected to a 3D-compatible TV and components (3D BD player, etc.) via High
Speed HDMI cables. Put on the 3D glasses, otherwise 3D images may not be viewed properly.
Select from the 2 methods below:
1. Method 1
This connection is for HDMI TV with ARC (Audio Return Channel).
Notes:
● Refer to the operation manual of the equipment to be connected.
● Fully insert the plugs to avoid fuzzy pictures or noises.
2. Method 2
This connection is for HDMI TV without ARC (Audio Return Channel).
Notes:
● To listen to sound via TV, turn off your connected DVD player or BD player or similar component.
● Connecting via this method may disable TV internal speakers.
System connections (continued)
Connecting to TV (with HDMI)
Caution:
● Turn off all other equipment before making this connection.
● Set the TV at low volume before turning on the system.
TV
DVD, BD player
or similar
To HDMI output
terminal
To HDMI
(ARC)
terminal
To HD M I
output
terminal
Subwoofer
TV
DVD, BD player
or similar
To HEADPHONE terminal
To HD M I
input
terminal
To audio output terminal
To HDMI terminal
or
HDMI OUTPUT
Subwoofer
E-12
2011 October 7
HT-SL70 / HT-SL75 ZB042
Connect to the TV using an audio cable.
1. Method 1
Notes:
● Connecting via this method may disable TV internal speakers.
● In some cases, a small background noise could emit from the sound bar, when you use the headphone connection with
a TV-Set. In such case, please change the connection to the HDMI/ARC or RCA-connection! This effect depends on
the used TV-Brand, model and age, and it is not a quality matter from the sound bar!
2. Method 2
Note:
To control the volume, some setting in the TV MENU is needed. For details refer to the operation manual of the TV.
Example: Go to the Setting Menu of the TV, select AUDIO OUT and choose VARIABLE.
However if this does not work, please use method 1.
System connections (continued)
Connecting a TV (with AUDIO IN (TV))
TV
Audio cable
To AUDIO IN (TV)
input terminal
Audio signal
To HEADPHONE terminal
Subwoofer
TV
To AUDIO IN (TV)
input terminal
Audio signal
To audio output terminal
RCA cable
Subwoofer
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-13
2011 October 7
Plug the AC power cord into a AC outlet, the stand-by
indicator turns RED.
This unit will automatically power on if:
1. TV or similar component which supports HDMI CEC, is
turned on.
2. Audio signal is detected from Audio input.
The stand-by indicator will turn BLUE if TV signal is
detected.
Notes:
● HDMI input will override the Audio input signal.
● Audio input will function only when there is no signal
from HDMI input.
● A slight audio delay after TV is turned ON does not
mean that the system is faulty. This is normal.
● “AQUOS speaker is enabled” message will be
displayed if SHARP LCD TV does not detect HT-SL70 /
HT-SL75 during power on. However the message
“AQUOS audio with AQUOS LINK is enabled” will be
displayed soon as HT-SL70 / HT-SL75 is detected.
These messages may vary for other TV model.
The Audio Return Channel (ARC) enables an HDMI ARC-
capable TV to send the audio stream to the HDMI OUT
terminal of the receiver. To use this function, your TV must
support the ARC. Make sure the LCD TV Audio output
setting is set to PCM, not other formats such as Dolby
Digital, DTS, etc. For details, refer to the operation manual
of the TV.
Volume can only be controlled from your TV.
This unit will automatically go to stand-by mode (indicator
turns RED) if:
1. TV or similar component which supports HDMI CEC, is
turned off.
2. No signal from Audio input is detected after 20 minutes.
General Control
Make sure to enable the HDMI CEC when making HDMI connection. For details, refer to the operation manual
of the TV.
To turn the power on
Audio Return Channel (ARC) (Audio
Return Channel submenu)
Volume
Power Off
E-14
2011 October 7
HT-SL70 / HT-SL75 ZB042
Many potential problems can be resolved by the owner
without calling a service technician.
If something is wrong with this product, check the following
before calling your authorized SHARP dealer or service
center.
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet. Condensation can cause the unit to
malfunction. If this happens, leave the power on until
normal playback is possible (about 1 hour). Wipe off any
condensation on the transmitter with a soft cloth before
operating the unit.
When this product is subject to strong external interference
(mechanical shock, excessive static electricity, abnormal
supply voltage due to lightning, etc.) or if it is operated
incorrectly, it may malfunction.
If the unit is not restored in the previous operation,
unplug and plug in the unit again
or
unplug all component connected and plug in again.
Periodically wipe the cabinet with a soft cloth.
Caution:
● Do not use chemicals for cleaning (gasoline, paint
thinner, etc.). It may damage the cabinet finish.
● Do not apply oil to the inside of each component. It may
cause malfunctions.
Troubleshooting chart
Symptom Possible cause
● No sound is heard. ● Is the input signal
(selection) set properly?
● Is HDMI compliant
equipment being used?
● Is the HDMI cable
connected correctly?
● Is the HDMI cable of the
correct type being used?
(with ARC)
● Does the sound input
support PCM signal?
● Do not connect or
disconnect an HDMI cable
while power is on. This
may lead to operation
problems.
● Noise is heard
during playback.
● Move the speaker away
from any computers or
mobile phones.
● The power is not
turned on.
● Is the unit unplugged?
● The protection circuit may
be activated. Unplug and
plug in the power cord
again after 5 minutes or
more.
● Volume cannot be
controlled.
● Check if the HDMI CEC is
enabled.
● For headphone or RCA,
TV setting (VARIABLE) is
required.
● 3D images not
displayed on the TV.
● Depending on the TV and
Video component, 3D
images may not be
displayed.
Check the operation
manual of the respective
component.
● Background noise
appears when
connecting with
headphone output of
TV-Terminal.
● Please change to HDMI/
ARC or RCA-Output
terminal from TV-Set. This
effect may occur
depending on your used
TV-Brand, model and age,
and it is not the sound bar
problem!
General
Condensation
If problem occurs during operation
Maintenance
Cleaning the cabinet
9
1
7
6
5
4
3
2
1
9
HT-SL70 / HT-SL75
E-15
2011 October 7
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specification
changes for product improvement without prior notice. The
performance specification figures indicated are nominal
values of production unit. There maybe some deviations
from these values in individual unit.
HORIZONTAL SETTING
VERTICAL SETTING
Specifications
Power source AC 120 V ~ 60 Hz
Power
consumption
40 W
Output power RMS: Total 200 watts
RMS:
Front Left/Right:
50 watts per channel into 3 ohms at
1 kHz, 10% total harmonic distortion
Subwoofer:
100 watts per channel into 4 ohms at
100 Hz, 10% total harmonic distortion
FTC:
Front (Left/Right):
Minimum 35 watts per channel into
3 ohms at 200 Hz to 20 kHz, 1% total
harmonic distortion
Subwoofer:
Minimum 93 watts per channel into
4 ohms at 100 Hz, 1% total harmonic
distortion
Output
terminal
HDMI™ (with Audio Return Channel)
output: (audio/video support to 1080p)
x 1
Input
terminal
Analog input (Audio in):
Stereo mini jack Ø 3.5 mm
Input impedance: 33 kohms
HDMI input: (audio/ video support to
1080p) x 1
Type Subwoofer system
6 - 5/16" (16 cm) woofer
Maximum
input power
200 W
Rated input
power
100 W
Impedance 4 ohms
Dimensions Width: 4 - 1/2" (115 mm)
Height: 16 - 5/8" (422 mm)
Depth: 12 - 1/16" (307 mm)
Weight 9.92 lbs. (4.50 kg)
General
Subwoofer
Type Full Range speaker system
7/8" x 4-1/2" (2.2 x 11.5 cm)
Full Range
Maximum
input power
100 W/CH
Rated input
power
50 W/CH
Impedance 3 ohms/CH (4 pieces parallel)
HT-SL75
For 60" TV.
Dimensions
Width: 54 - 17/32" (1385 mm)
Height: 1" (26 mm)
Depth: 1 - 31/32" (50 mm)
Weight 2.74 lbs. (1.25 kg)
For 70" TV.
Dimensions
Width: 63 - 3/8" (1610 mm)
Height: 1" (26 mm)
Depth: 1 - 31/32" (50 mm)
Weight 2.95 lbs. (1.34 kg)
HT-SL70
For 46" TV.
Dimensions
Width: 40 - 3/16" (1071 mm)
Height: 1 - 1/32" (26 mm)
Depth: 1 - 31/32" (50 mm)
Weight 2.54 lbs. (1.15 kg)
For 52" TV.
Dimensions
Width: 47 - 13/32" (1204 mm)
Height: 1 - 1/32" (26 mm)
Depth: 1 - 31/32" (50 mm)
Weight 2.65 lbs. (1.20 kg)
HT-SL75
For 60" TV.
Dimensions
Width: 6 - 5/16" (160 mm)
Height: 34 - 27/32" (885 mm)
Depth: 6 - 5/16" (160 mm)
Weight 3.75 lbs. (1.70 kg)/each
For 70" TV.
Dimensions
Width: 6 - 5/16" (160 mm)
Height: 39 - 3/4" (1010 mm)
Depth: 6 - 5/16" (160 mm)
Weight 3.75 lbs. (1.70 kg)/each
HT-SL70
For 46" TV.
Dimensions
Width: 6 - 5/16" (160 mm)
Height: 27 - 13/16" (706 mm)
Depth: 6 - 5/16" (160 mm)
Weight 2.09 lbs. (0.95 kg)/each
For 52" TV.
Dimensions
Width: 6 - 5/16" (160 mm)
Height: 30 - 13/16" (782 mm)
Depth: 6 - 5/16" (160 mm)
Weight 2.09 lbs. (0.95 kg)/each
Soundbar speaker
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Sharp HT-SL75 User manual

Sharp
Brand
Sharp
Model
HT-SL75
Category
Supplementary music equipment
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents