Poulan 2155 User manual

Brand: Poulan

Model: 2155

Category: Power chainsaws

Type: User manual

This manual is also suitable for

Poulan

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner I'outil au d_taillant.

• 1-800-554-6723

www.poulan.com

Instruction Manual

Manual de Instrucciones

Manuel d'lnstructions

1950 / 1975 / 2050 / 2055 / 2075

2150 / 2155 / 2175 / 2350 / 2375

2050WT / 2150PR

For Occasional Use Only

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea etmanual de instrucciones y siga todas Iasadvertencias e en-

strucciones de seguridad. Etno hacerlo puede resuItar en tesiones

graves.

AVERTISSEMENT:

Lire le manuel d'instructions et bien respecter tous tes avertisse-

merits et toutes tes instructions de s_curit& Tout defaut de le faire

pourrait entra_ner des blessures graves.

Poulan Poulan

t030 Stevens Creek Road 5855 TerryFox Way

Augusta, GA 30907 Mississauga, Qntario L5V 3E4

545186768 Rev. 1 4/15/08 BRW

----_ WARNING! This chain

saw can be dangerous! Care-

less or improper use can cause

serious or even fatal injury

Always wear appropriate ear

protection, eye protection

and head protection.

Read and understand the

instruction manuaI before

using the chain saw.

Measured maximum kick-

back value without chain

brake for the bar and chain

combination on the label

@ A_ways use two hands when operating the chain saw.

WARNING! Contacting the guide bartip with any object

should be avoided; tip contact may cause the guide bar to

move suddenly upward and backward, which may cause se-

rious injury.

Starting Fleminder

Move ON/STOP switch to

a _ the ON position.

Prime aX Slowly press primer bulb

(_)_ 6 times.

Full Choke Pull choke/fast idle lever

outtothefu,extent{to

the PULL CHOKE posi-

-- tion)

Pull 5X

Half Choke

PUll to Statl

Pul_the starter rope

sharply 5 times with your

right hand.

Push the choke/fast idle

lever into the HALF

CHOKE position.

Pullthe starterrope sharply

with your right handun_l

theengine stairs.

_ll WARNING: Always disconnect

spark pIug wire and place wire where itcan-

not contact spark plug to prevent accidental

starting when setting up, transporting, ad-

justing or making repairs except carburetor

adjustments.

Because a chain saw is a high-speed wood-

cutting toef, speciaI safety precautions must

be observed to reduce the risk of accidents.

Careless or improper use of this toef can

CaUSe SeRous Enlui'y

PLAN AHEAD

• Read this manuef carefully until you com-

pletely understand and can follow efl safety

rules, precautions, and operating instruc-

tions before attempting to use the unit.

• Restdct the use of your saw to adult users

who understand and can follow safety

rules, precautions, and operating instruc-

tions found in this manual.

• Wear protective gear. Always use steeF

toed safety footwear with non-slip soles;

snug-fitting clothing; heavy-duty, non-slip

gloves; eye protection such as non-fog-

ging, vented goggles or face screen; an

approved safety hard hat; and sound barri-

ers (ear plugs or mufflers) to protect your

hearing. Regular users should have hear-

ing checked regularly as chain saw noise

can damage hearing. Secure hair above

shou*der Iength.

Hearing SafetyHat

Protection_Jj Eye

"'"_ i_i_ _"Protection

Snug

Fitting"-----._ HeavyDuty

Clothing,_plP_l_c/GIoves

Safety_1_SafetyChaps

• Keepallpartsofyourbodyawayfromthe

chainwhentheengineisrunning.

• Keepchildren,bystanders,andanimalsa

minimumof30feet(10meters)awayfrom

theworkarea.Donotal}owotherpeople

oranimalstobenearthechainsawwhen

startingoroperatingthechainsaw.

• Donothandleoroperateachainsawwhen

youarefatigued,ill,orupset,orifyouhave

takenalcohol,drugs,ormedication.You

mustbeingoodphysicalconditionandmen-

tatlyaIed.Chainsawworkisstrenuous.If

youhaveanyconditionthatmightbeaggra-

vatedbystrenuouswork.checkw_thyour

doctorbeforeoperaflngachainsaw.

• Carefullyplanyoursawingoperationinad-

vance.Donotstartcuttingunfllyouhavea

clearworkarea,securefooting,and,ifyou

arefellingtrees,aplannedretreatpath.

OPERATEYOUR SAW SAFELY

• Do not operate a chain saw with one hand.

Serious injury to the operator, helpers, by-

standers or any combination of these per-

sons may result from one-handed opera-

tion. A chain saw ts intended for

two-handed use

• Operate the chain saw only in a weII-venti-

latad outdoor area.

• Do not operate saw from a ladder or in a tree.

• Make sure the chain wilt not make contact

with any object while starting the engine.

Never try to start the saw when the guide

bar is in a cut.

• Do not put pressure on the saw at the end of

the cut. Applying pressure can cause you to

lose controt when the cut is completed.

• Stop the engine before setting the saw

down.

• Do not operate a chain saw that is dam-

aged, improperly adjusted, or not com-

pletaly and securely assembled. Always

replace bar, chain, hand guard, or chain

brake immediately if it becomes damaged,

broken or is otherwise removed.

• With the engine stopped, hand carry the

chain saw with the muffler away from your

body, and the guide bar and chain to the

rear, preferably covered with a scabbard.

MAINTAIN YOUR SAW IN GOOD

WORKING ORDER

• Have aII chain saw service performed by a

qualified service dealer with the exception

of the items listed in the maintenance sac-

tion of this ma_uaL For example, ifimprop-

er tools are used to remove or hold the fly-

wheel when servicing the clutch, structural

damage to the flywheel can occur and

cause the flywheel to burst.

• Make certain the saw chain stops moving

when the throttle trigger is released. For

correction, refer to CARBURETOR AD-

JUSTMENTS

• Never modify your saw in any way

• Keep the handles dry, clean, and free of oil

or fuel mixture.

• Keep fuel and oil caps, screws, and fas-

teners securely tightened.

• Use only PouIan accessorfes and re-

placement parts as recommended.

HANDLE FUEL WITH CAUTION

• Do not smoke while handIing fuel or while

operating the saw.

• Eliminate all sources of sparks or flame in

the areas where fuel is mixed or poured.

There should be no srooking, open flames,

or work that could cause sparks. Allow en-

gine to cool before refueling.

• Mix and pour fuel in an outdoor area on

bare ground; store fuel in a cool, dry, we_l

ventilated place; and use an approved,

marked container for all fuel purposes.

Wipe up all fuel spills before starting saw

• Move at least 10 feet (3 meters) from fuel-

ing site before starting engine.

• Turn the engine off and let saw cool in a

non-combustible area, not on dry leaves,

straw, paper, etc Slowly remove fuel cap

and refuel unit.

• Store the unit and fueHn an area where fuel

vapors cannot reach sparks or open

flames from water heaters, electric motors

or switches, fumaces, etc.

KICKBACK

ji_ WARNING: Avoid kickback which

can result in serious injury. Kickback is the

backward, upward or sudden forward motion

of the guide bar occurdng when the saw

chain near the upper tip of the guide bar con-

tacts any object such as a log or branch, or

when the wood closes in and pinches the

saw chain in the cut. Contacting a foreign ob-

ject in the wood can also result in loss of

chain saw control.

• Rotational Kickback can occur when the

moving chain contacts an object at the up-

per tip of the guide bar. This contact can

cause the chain to dig into the object,

which stops the chain for an instant. The

result is a lightning fast, reverse reaction

which kicks the guide bar up and back to-

ward the operator.

• Pinch-Kickback can occur when the the

wood closes in and pinches the moving

saw chain in the cut aIong the top of the

guide bar and the saw chain is suddenly

stopped. This sudden stopping of the

chain results in a reversa_ of the chain

force used to cut wood and causes the

saw to move in the opposite direction of the

chain rotation. The saw is driven straight

back toward the operator.

• Pull-In can occur when the moving chain

contacts a foreign object in the wood in the

cut along the bottom of the guide bar and the

saw chain is suddenly stopped. This sudden

stopping pulls the saw forward and away

from the operator and could easily cause the

operator to lose controt of the saw

Avoid Pinch-Kickback:

• Be extremely aware of situations or ob-

structions that can cause material to pinch

the top of or otherwise stop the chain.

• Do not cut more than one log at a time.

• Do not twist the saw as the bar is with-

drawn from an undercut when bucking

Avoid Pull-In:

• Always begin cutting with the engine at full

speed and the saw housing against wood.

• Use wedges made of pIastic or wood.

Never use metal to hold the cut open

• Use the Reduced-Kickback Guide Bar

and Low-Kickback Chain specified for

your saw

MAINTAIN CONTROL

Stand to the

left of the saw ,_

_ Thumb on

underside of

handlebar

Never

hand positions

Ctear The Working Area

REDUCE THE CHANCE OF

KICKBACK

• Recognize that kickback can happen.

With a basic understanding of kickback,

you can reduce the element of surprise

which contributes to accidents.

• Never let the moving chain contact any ob-

ject at the tip of the guide bar

• Keep the working area free from obstruc-

tions such as other trees, branches, rocks,

fences, stumps, etc Eliminate or avoid

any obstruction that your saw chain could

hit while you are cutting When cutting a

branch, do not let the guide bar contact

branch or other objects around it.

• Keep your saw chain sharp and properly

tensioned. A loose or dull chain can in-

crease the chance of kickback occurring.

Follow manufacturer's chain sharpening

and maintenance instructions. Check ten-

sion at reguIar intervals with the engine

stopped, never with the engine running.

Make sure the chain brake nuts are se-

curely tightened after tensioning the chain.

• Seginandcontinuecutfingatfullspeed If

the chain is moving at a slower speed,

there is greater chance of kickback occur-

ring.

• Cut one log at a time.

• Use extreme caution when re-entering a

previous cut.

• Do not attempt cuts starting with the tip of

the bar (plunge cuts).

• Watch for shifting logs or other forces that

could close a cut and pinch or fall into

chain.

Thumb on underside of

handlebar

• Keep a good, firm grip on the saw with both

hands when the engine is running and don't

let go. A firm grip will help you reduce kick-

back and maintain control of the saw. Keep

the fingers of your left hand encircling and

your left thumb under the ftont handlebar.

Keep your dght hand completely around the

rear handle whether your are right handed or

left handed. Keep your left arm straight with

the elbow locked.

• Position your left hand on the front handle-

bar so it is in a straight line with your right

hand on the rear handle when making

bucking cuts. Never reverse right and left

hand positions for any type of cutting.

• Standwithyourweightevenly balancedon

both feet.

• Stand slighfiy to the Ieft side of the saw to

keep your body from being in a direct line

with the cutting chain.

• Do not overreach. You could be drawn or

thrown off balance and lose control of the

saw

• Donotcutaboveshoutderheight. Itisdiffi-

cult to maintain control of saw above

shoulder height

KICKBACK SAFETY FEATURES

_ WARNING: Thefollowingfeatures

are included on your saw to help reduce the

hazard of kickback; however, such features

will not totally e}iminate this danger. As a

chain saw user, do not rely only on safety de-

vices. You must follow eli safety precau-

tions, instructions, and maintenance in this

manual to hetp avoid kickback and other

forces which can result in serious injury

• Reduced-KickbackGuideBar,designed

withasmallradiustipwhichreducesthe

sizeofthekickbackdangerzone on the

bar tip. A Reduced-Kickback Guide Bar

has been demonstrated to significantly re-

duce the number and seriousness of kick-

becks when tested in accordance with

safety requirements for gasoline powered

chain saws as set by ANSI B175.1

ReducedKickbackSymrnetricalGuideBar

allRadiusTip

Symrnetrica_ Guide Bar _.,._

Large Radius Tip

• Low-Kickback Chain, designed with a

contoured depth gauge and guard link

which dedect kickback force and allow

wood to gradually ride into the cutter Low-

Kickback Chain has met kickback per-

formance requirements when tested on a

representative sample of chain saws be-

low 3.8 cubic inch displacement specified

in ANSi B175.1

Chain to gradualJy ride

_ntocutter

_ _X _C an ObstructMatelial

N_ a LOW Kickback Chain

• Front Hand Guard, designed to reduce the

chance of your Ieft hand contacting the chain

if your hand slips off the front handlebar.

• Position of front and rear handlebars, de-

signed with distance between handles and

'ingJne" with each other. The spread and

"in-line" position of the hands provided by

this design work together to give balance

end resistance in controlling the pivot of

the saw back toward the operator if kick-

back occurs.

CHAIN BRAKE AND CKA ANGLE

• Chain Brake, designed to stop the chain in

the event of kickback.

,tt _____._A

dnI_W/-_I-(NIN£_: WE DO NOT REP-

RESENT AND YOU SHOULD NOT AS-

SUME THAT THE CHAIN BRAKE WILL

PROTECT YOU IN THE EVENT OFA KICK-

BACK. Kickback is a lightning fast action

which throws the bar and rotating chain back

and up toward the operator. Kickback can be

caused by allowing contact of the bar tip in tile

danger zone wifh any hard object Kickback

can also be caused by pinching the saw chain

along the top of the guide baE This action may

push the guide bar rapidly back toward the op-

erator. Either of these events may cause you

to lose control of the saw which could result in

serious injury or even death. DO NOT RELY

UPON ANY OF THE DEVICES BUILT INTO

YOUR SAW. YOU SHOULD USE THE SAW

PROPERLY AND CAREFULLY TO AVOID

KICKBACK. Reduced-kickback guide bars

and low-kickback sew chains reduce the

chance and magnitude of kickback and are

recommended. Your saw has a low kickback

chain and bar as original equipment. Repairs

on a chain brake should be made by an autho-

rized servicing dealer. Take your unit to the

place of purchase if purchased from a servic-

ing dealer, or to the nearest authorized master

service dealer.

• _p contact in some cases may cause a light-

ning fast reverse REACTION, kicking guide

bar up end back toward operator.

• Pinching the saw chain along the top of the

guide bar may push the guide bar rapidly

back toward the operator

• Either of these reactions may cause you to

lose control of the saw which could result in

serious injury. Do not rely excIusively upon

devices buiif into your saw.

,_ WARNING: Computed kickback

angle (CKA) listedon your saw and listed in the

CKA table below represents angle of kickback

your bar and chain combinations will have

when tested in accordance with CSA (Cana-

dian Standards Association) and ANSI stan-

dards. When purchasing replacement bar and

chain, considerations should be given to the

lower CKA values Lower CKA values repre-

sent safer angles to the user. higher values in-

dicate more angle and higher kick energies

Computed angles represented indicate total

energy and angle associated without activation

of the chain brake during kickback Activated

angle represents chain stopping time relative to

activation angle of chain break and resulting

kick angle of saw. in all cases lower CKA val-

ues represent a safer operaffng environment

for the user.

The following guide bar and chain combina-

tions meet kickback requirements of CSA

Standards Z62.f, Z62.3. & ANSI B175.1 when

used on saws listed inthis manual Use of bar

and chain combinations other than those listed

is not recommended and may not meet the

OKA requirements per standard.

Computed kickback angle (CKA

BAR

MODEL

1950/1975/

2050/2050WT

2055/2075/

2150/215OPR

2155/2175/

2350/2375

Table

P/N Length CHAIN P/N

952044368 14" 952051209

952044370 16" 952051211

952044418 18" 952051338

CKA without chain brake

19'

NOTE: If this saw is to be used for com-

mercial logging, a chain brake is required

and shatl not be removed or otherwise dis-

ab+ed to comply with Federal OBHA Regula-

tions for Commercial Logging.

_kWARNING: The engine exhaust

from this product contains chemicals known

to the State of California to cause cancer,

birth defects or other reproductive harm.

SAFETY NOTICE: Exposure to vibrations

through prolonged use of gasoline powered

hand tools couid cause blood vesse_ or nerve

damage in the fingers, hands, and joints of

beagle prone to circulation disorders or

abnormal swe}lings. Prolonged use in cold

weather has been tinked to blood vessel

damage in otherwise healthy people. If

symptoms occur such as numbness, pain,

loss of strength, change in skin color or texture,

or loss of feeling in the fingers, hands, or joints,

disconbnue the use of this too+ and seek

medicat attention. An anti-vibration system

does not guarantee the avoidance of these

problems. Users who operate power toots on

a continua+ and regular basis must monitor

closely their physical cond+tion and the

cond_on of this tool

SPECIAL NOTICE: Your saw is equipped

with a temperature liming muffler and spark

arresbng screen which meets the

requirements of California Codes 4442 and

4443. All U.S. forest land and the states of

California+ Idaho, Maine, Minnesota, New

Jersey, Oregon, and Washington require by

faw that many internal combustion engines to

be equipped with a spark arresting screen if

you operate a chain saw in a state or locale

where such regulations exist, you are legally

responsibte for maintaining the operating

cond_on of these parts. Failure to do so is a

victet_on of the law. Refer to the SERVICE

section for maintenance of the spark arresting

screen. Fd+iure to follow all Safety Rules and

Precautions can result in serious injury. If

situations occur which are not covered in this

manual, use care and good judgement, ff you

need assistance, contact your authorized

service dealer or cali t-800-554-6723.

Protective gloves (not provided) should be

worn during assembly

ATTACHING TH E BAR &CHAIN (If not

already attached)

WARNING: if received assembled,

repeat all steps to ensure your saw is properly

assembled and all fasteners are secure. Al-

ways wear gloves when handling the chain.

The chain is sharp and can cut you even when

is not moving!

1. Loosen and remove the chain brake

nuts and the chain brake from the saw.

2 Remove the pIastic shipping spacer (if

present).

Location of shipping spacer

a_ Chain Brake

Ch Nuts

Bar Tool

3. An adjusting pin and screw Lsused to ad-

just the tens+on of the cha+n It is very im-

portant when assembling the bar, that the

pin facated on the adjusting screw aligns

into a hole in the bar. Turning the screw will

move the adjustment pin up and down the

screw. Locate this adjustment before you

begin mounting the bar onto the saw. See

il:ustrationbelow.

STANDARDS: This saw is listed by Under-

writer's Laboratories, inc., in accordance with:

ANSi B175.1-2000 American National

Standards for Gasoline-Powered Chain

Saws - Safety Requirements

CSA Z62.1-03 Chain Saws - Occupabenal

Health and Safety

CSA Z62.g-96 Chain Saw Kickback Occu-

pational Health and Safety

Adjustment facated on Chain Brake

4. Turn the adjusting screw by hand coun-

terclockwise untii the adjusting pin just

touches the stop. This should allow the

pin to be near the correct position.

5 Slide guide bar behind c+utoh drum until

guide bar stops against crutch drum

sprocket.

6. Carefullyremovethechainfromthepack-

age.Holdchainw_thedrivelinks as

shown.

DIIRECTiON OF ROTATION

Drive Unks

Place chain onto the sprocket

7. Place chain over and behind efutch, fit-

ting the dnve ]inks in the clutch drum

sprocket.

8. Fit bottom of drive links between the

teeth in the sprocket in the nose of the

guide bar.

g. Fit chain drive links into bar groove.

10. Pu]I guide bar forward until chain is snug

in guide bar groove Ensure all drive

_inks are in the bar groove

NOTE: CHAIN BRAKE MUST BE

DISENGAGED BEFORE INSTALLA-

TION ON THE SAW. TO DISENGAG E

CHAIN BRAKE, PULL THE FRONT

HAND GUARD BACK TOWARD THE

REAR OF THE CHAIN BRAKE AS

FAR AS POSSIBLE (SEE ILLUSTRA-

TION).

Fro_ 1_ _LAI_ ED _

"__-_:J! ii_"

GAGED

/ _. Ghatn Brake

11. Now, install chain brake making sure the

adjusting pin is positioned in the lower

hole in the guide bar Remember this pin

moves the bar forward and backward as

the screw is turned.

12 Install chain brake nuts and finger tight-

en only. Once the chain is tensioned,

you will need to tighten chain brake nuts

CHAIN TENSION

(Including units with chain already installed)

NOTE: When adjusting chain tension,

make sure the chain brake nuts are finger

tight onIy. Attempting to tension the chain

when the chain brake nuts are tight can

cause damage.

Checking the teneion:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move the chain around

the bar. tf the chain does not rotate, _ is too

tight. If too loose, the chain will sag below the

bar

Chain Brake Nuts Tool (Bar Tool)

Adjueting the tension:

Chain tension is very important. Chain

stretches during use. This is especially true

during the first few times you use your saw

Always check chain tension each time you

use and refuel your saw.

You can adjust the chain tension by loosen-

ing the chain brake nuts and turning the ad-

justing screw 1/4 of a turn while lifting up on

the ban

• If chain is too tight, turn adjusting screw t/4

turn counterclockwise.

• If chain is too loose, turn adjusting screw

t/4 turn clockwise.

f'-_ LL_tJ, / Adju sting / /

_ O Screw

Chain Brake Nuts Guide Bar

Adjusting Screw - 1/4Turn

• Lift up the tip of the bar and tighten the

chain brake nuts with the bar tool.

• Recheck chain tension.

KNOW YOUR CHAIN SAW

Chain Brake

_Nuts .

_,WARNING: if the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR

CHAIN SAW Compare the illustrations with your unit to familiarize yourself with the location of

the various contrefs and adjustments. Save this manual for future reference.

Chain Front Hand Guard "_- Front Handle

Adjustment Tool

(Bar Tool) Starter Rope

ON/STOP

Switch

Chain Muffler

Primer

Bar Oit Fill Cap Housing Fuel Mix Fill Cap

Cylinder Cover

Throttle _

Lockout o

Rear \ _ttiet

Handle _

Throttle Choke/

Trigger Fast idle Chain Chain Nuts

Lever Brake Catcher

ON/STOP SWITCH

The ON/STOP SWITCH is used to stop the

engine

THRO'FrLE TRIGGER

Time THROlqLE TRIGGER controls engine

speed.

THRO'FrLE LOCK-OUT

Time THRO]q-LE LOCK-OUT must be

pressed before you can squeeze the throttle

thgger. This feature prevents you from acci-

dentally squeezing the trigger.

CHOKE/FAST IDLE LEVER

The choke and fast idle are set by pulIing the

CHOKE/FAST IDLE LEVER out to the falI ex-

_ Chain

s%1 Sw,,ng fr#a°

'_ Chain Brake '

Bar Sprocket Hefe

tent for cold staring or after refueling. The

choke provides additional fuef to the engine

during cefd staring.

PRIMER BULB

The PRIMER BULB circulates fuel to tile car-

burefor to prowde quicker starting.

CHAIN BRAKE

The CHAIN BRAKE is a device designed to

stop the chain if kickback occurs. The chain

brake activates automatically in the event of

kickback. The chain brake activates manually

if the front hand guard is pushed forward. The

chain brake is disengaged by pulling the front

hand guard back toward the front handle as far

as possible.

CHAIN TENSION

Itis normal for a new chain to stretch during the

first 15 minutes of operation. You should check

your chain tension ftequentiy. See CHAIN

TENSION under the ASSEMBLY section.

FUELING ENGINE

_k WARNING: Remove fuel cap s_ow-

ly when refueling.

_i_ WARNING: Muffler is very hot dur-

ing and after use. Do not touch the muffler or

allow combustible matedal such as dry

grass or fuel to do so

system of an engine while in storage To

avoid engine problems, the fuel system

should be emptied before storage for 30

days or longer. Drain the gas tank, start the

engine and let it run until the fuel lines and

carburetor are empty. Use fresh fuef next

season. See STORAGE section for addi-

tional information.

This engine is certified to operate on unleaded

gasoline. Before operation, gasoline must be

mixed with a good quality synthetic 2-cycle air-

cooled engine oit designed to be mixed at a ra-

tioof4O:l Poulan&'VEED EATER brandsyn-

thetic oil is recommended. A 40:1 ratio is

obtained by mixing 3.2 ounces (95 ml) of oil

with 1 gallon (4-liters) of unleaded gasefine. In-

cluded with this saw is a 3.2 ounce container of

PoulanfWEED EATER brand synthetic oil.

Pour the entire content_ of this container into f

gallon of gasoline to achieve the proper fuel

mixture. DO NOT USE automotive or marine

oil. These oils will cause engine damage.

When mixing fuef feflow the instructions

printed on the container. Always read and

follow the safety rules listed under HANDLE

FUEL WITH CAUTION

BAR AND CHAIN LUBRICATION

The bar and chain require continuous lubri-

cation. Lubrication is provided by the auto-

matic oiler system when the oil tank is kept

filled. Lack of oil will quickly ruin the bar and

chain. Too little oil will cause overheating

shown by smoke coming from the chain and/

or discoloration of the bar.

In freezing weather oil will thicken, making it

necessary to thin bar and chain oii with a

small amount (5 to 10%) of # 1 Diesel Fuel or

kerosene Bar and chain oil must be free

flowing for the oil system to pump enough oiI

for adequate lubdcedon.

Genuine Poulan bar and chain oil is recom-

mended to protect your unit against exces-

sive wear from heat and fedtion. Poulan oil

resists high temperature thinning.

If PouIan bar and chain oil is not available,

use a good grade SAE 30 oil

• Never use waste oil for bar and chain lubb-

cation

• Always stop the engine before removing

the oil cap.

IMPORTANT

Experience indicates that a_cohef-blended

fuels (called gasohot or using ethanol or

methanol) can attract moisture which leads

to separation and formation of acids during

storage. Acidic gas can damage the fuel

I_kWAHNIN(3: The chain must not

move when the engine runs at idle speed. If

the chain moves at idle speed refer to CAR-

BURETOR ADJUSTMENT within this

manual. Avoid contact with the muffler. A hot

muffler can cause serious burns

To stop the engine move the ON/STOP

switch to the STOP position.

To start the engine hold the saw firmly on

the ground as illustrated Make sure the

chain is free to turn without contacting any

object

Use only 15" - 18" (38 - 45 cm) of

rope per pull

Hold saw firmly while pul_ing starter rope.

Starter Rope Handle

Right Foot Through Rear Handle

IMPORTANT POINTS TO REMEMBER

When pulling the starter rope, do not use the

full extent of the rope as this can cause the

rope to break. Do not let starter rope snap

back Hold the handle and let the rope re-

wind slowly.

For cold weather starting, start the unit at

FULL CHOKE: allow the engine to warm up

before squeezing the throttle trigger.

NOTE: Do not attempt to cut matebal with

the choke/fast idle lever in the FULL CHOKE

position.

STARTING A COLD ENGINE (or

warm engine after running out of

fuel)

NOTE: h_ the following steps, when the

choke/fast idle lever is pulled out to the full

extent, the correct throttle setting for starting

is set automatically.

ON/STOP SWITCH

(SIDE VIEW)

_ ON

STOP

1. Move ON/STOP switch to the ON posi-

tion.

2. Slowly press primer bulb 6 times

3. Pult choke/fast idle lever out to the full

extent (to the FULL CHOKE position)

4. Pulithe starter rope sharply 5 times with

your nght hand. Then, proceed to the

next step.

NOTE: If the engine sounds as if it is trying

to start before the 5th putl, stop pulling and

immediately proceed to the next step.

5. Push the choke/fast idle lever in to the

HALF CHOKE osition.

CHOKE/FA_T IDLE LEVER

o_EW)

fast idle lever OFF HALF FULL

8. Pul} the starter rope sharp}y with your

right hand until the engine starts

7. Altow the engine to run for approximate-

Iy 30 seconds Then, squeeze and re-

tease the throttle trigger to allow engine

to return to idle speed

STARTING A WARM ENGINE

1. Move ON/STOP switch to the ON posi-

tion

2. Slowly press primer bulb 6 times.

3. Puli the choke/fast idle lever out to the

HALF CHOKE position.

4-. Pull the starter rope sharply with your

right hand unfl_ the engine starts.

5. Squeeze and release throttle trigger to

allow engine to return to idle speed.

DIFFICULT STARTING (or 8tarring a

flooded engine)

The engine may be flooded with too much

fuel if it has not started after fO pulls.

Flooded engines can be cleared of excess

fuel by pushing the choke/fast idle lever in

completely (to the OFF CHOKE position)

and then following the warm engine starting

procedure listed above. Ensure the ON/

STOP sw_tch is in the ON position.

Starting could require pulling the starter rope

handle many times depending on how badly

the unit is flooded. If engine fails to start, refer

to the TROUBLESHOOTING TABLE or call

1-800-554-6723.

CHAIN BRAKE

_I, WARNING: tf the brake band is

worn too thin it may break when the chain

brake is triggered With a broken brake band,

the chain brake will not stop the chain The

chain brake should be replaced by an autho-

rized service dealer ifany part is worn to less

than O O2O" (05 mm) thick. Repairs on a

chain brake should be made by an autho-

rized service dealer Take your unit to the

place of purchase if purchased from a ser-

vicing dealer, or to the nearest authorized

master service dealer.

• This saw is equipped with a chain brake

The brake is designed to stop the chain if

kickback occurs

• The inertia-activated chain brake is

activated if the front hand guard is pushed

forward, either manually (by hand) or

automatically (by sudden movement)

• If the brake is already activated, it is

disengaged by pulling the front hand guard

back toward the front handle as far as

possible

• When cutting with the saw, the chain brake

must be disengaged

Braking function control

CAUTION: The chain brake must be

checked several times daily. The engine

must be running when performing this proce-

dure. This is the only instance when the saw

should be placed on the ground with the en-

gine runmng.

Place the saw on firm ground Grip the rear

hand}e with your right hand and the front han-

dle with your left hand. Apply full throttle by

fuily depressing the throttle trigger. Activate

the chain brake by turning your left wrist

against the hand guard without releasing

your grip around the front handle The chain

should stop immediately

Inertia activating function control

_WARNING: When performing the

following procedure, the engine must be

turned off

G rip the rear handle with your right hand and

the front handle with your left hand. Hold the

chain saw approximately 14" (35 cm) above

a stump or other wooden surface Release

your grip on the front handle and use the

weight of the saw to let the tip of the guide bar

fall forward and contact the stump. When the

tip of the bar hits the stump, the brake should

activate

IMPORTANTPOINTS

• Check chain tension before first use and

after f minute of operation. See CHAIN

TENSION Lnthe ASSEMBLY section

• Cut wood only. Do not cut metal, plastics,

masonry, non-wood building materials, etc.

• Stop the saw ff the chain strikes a foreign

object. Lnspect the saw and repair or re-

place parts as necessary.

• Keep the chain out of dirt and sand Even a

small amount of dirt will quickly dult a chain

and thus increase the possibil*ty of kickback.

• Practice cutting a few small logs using the

foIIowing techniques to get the "feeF of us-

ing your saw before you begin a major

sawing operation.

• Squeeze the throftle trigger and allow

the engine to reach full speed before

cutting.

• Begin cutting with the saw frame

against the log.

• Keep the engine at full speed the entire

time you are cutting.

• ALlow the chain to cut for you. Exert only

light downward pressure. If you force

the cut, damage to the bar, chain, or en-

gine can result.

• Release the throttle trigger as soon as

the cut is completed, allowing the en-

gine to idle. If you run the saw at full

throttle without a cutting Load, unneces-

sary wear can occur to the chain, bar,

and engine

• To avoid tosing conttoL when cut is com-

plete, do not put pressure on saw at end

of cut.

• Stop the engine before setting the saw

down after cutting.

TREE FELLING TECHNIQUES

WARNING: Check for broken or

dead branches which can fall wMle cutting

causing serious injury. Do not cut near build-

ings or etecthcal wires if you do not know the

direction of tree fall, nor cut at night since you

will not be ale to see welt, nor during bad

weather such as rain. snow, or strong winds,

etc. if the tree makes contact with any utility

line, the utility company should be notified

immediately.

• CarefuLly plan your sawing operation in ad-

vance.

• Cleartheworkarea Youneedacleararea

alI around the tree so you can have secure

footing.

• The chain saw operator should keep on

the uphLtl side of the terrain as the tree is

likely to rolI or slide downhill after it is relied.

• Study the naturat conditions that can cause

the tree to falI in a particular direction.

Natural conditions that can cause a tree to

falI in a particular direction include:

• The wind direction and speed.

• The lean of the tree. The lean of a tree

might not be apparent due to uneven or

sloping terrain. Use a plumb or level to de-

termine the dLrection of tree Lean.

• Weight and branches on one side.

• Surrounding trees and obstacles

Look for decay and rot. if the trunk is rotted,

it can snap and fall toward the operator

Check for broken or dead branches which

can fall on you while cutting.

Make sure there is enough room for the tree

to fail. Maintain a distance of 2 1/2 tree

lengths from the nearest person or other ob-

jects Engine noise can drown out a warning

caLL Remove dirt, stones, loose bark, nails,

staples, and wire from the tree where cuts

are to be made Plan a clear retreat path to

the rear and diagonal to the line of fall.

_x_ e Plan a clear retreat path

_"- _ - O'''"_ - Direction of Fall

FELLtNG LARGE TREES

(6 inches (t5 cm) in diameter or Iarger)

The notch method is used to fell large trees.

A notch is cut on the side of the tree in the de-

sired direction of fal_ After a felling cut is

made on the opposite side of tree, the tree

will tend to fall into the notch

NOTE: If the tree has large buttress roots,

remove them before making the notch, ff us-

ing saw to remove buttress roots, keep saw

chain from contacting ground to prevent dull-

ing of the chain.

NOTCH CUT AND FELLING THE

TREE

• Make notch cut by cutting the top of the

notch first. Cut through 1/3 of the diameter

of the tree. Next complete the notch by cut-

ting the bottom of the notch. See i_lustta-

tion. Once the notch is cut remove the

notch of wood from the tree

Final (felling) cut here, 2 inches

(5 cm) above center of notch

First cut \.._1 ..._2 ,___

i' ... J..

Notch _ 2-

Second cut

• After removing the wood from the notch,

make the felling cut on the opposite side of

the notch. This is done by making a cut about

two inches (5 cm) higher than the center of

the notch. This will leave enough uncut wood

between the felling cut and the notch to form

a hinge. This hinge will help prevent the tree

from fal_ing in the wrong direction

Hinge holds tree on stump and helps

control fall

Opening

of felling

Closing of

notch

NOTE: Before felling cut is complete, use

wedges to open the cut ff necessary to

control the direction of fall. To avoid kickback

and chain damage, use wood or plastic

wedges, but never steel or iron wedges.

• Be alert to signs that the tree is ready to

fall: cracking sounds, widening of the fell-

ing cut. or movement in the upper

branches.

• As tree starts to fall, stop saw, put it down,

and get away quickty on your planned re-

treat path

• DO NOT cut down a partially failen tree with

your saw. Be extremely caubeus with par-

flally fallen trees that may be beody sup-

ported. When a tree doesn't falI completely,

set the saw aside and pull down the tree with

a cable winch, block and tackle, or tractor

CUTTING A FALLEN TREE

(BUCKING)

Bucking is the term used for cutting a fallen

tree to the desired log size

A4_WARNING: Do not stand on thelog

being cut Any portion can roll causing loss

of footing and control. Do not stand downhil_

of the log being cut.

IMPORTANT POINTS

• CUt onty one log at a time.

• Cut shattered wood very carefully; sharp

pieces of wood could be flung toward opera-

toe

• Use a sawhorse to cut smaII Iogs. Never

allow another person to hold the log while

cutting and never hold the log with your leg

or foot.

• Do not cut in an area where logs, limbs,

and roots are tangled such as in a blown

down area. Drag the logs into a clear area

before cutting by pulliog out exposed and

cleared logs first.

TYPES OF CUTTING USED FOR

BUCKING

AqLWARNING: If saw becomes

pinched or hung in a log, don't try to force it

out. You can Iose control ofthe saw res ulting

in injury and/or damage to the saw. Stop the

saw, drive a wedge of plasfic or wood into the

cut untiI the saw can be removed easiIy. Re-

start the saw and carefully reenter the cut. To

avoid kickback and chain damage, do not

use a metalwedge. Do not attempt to restart

your saw when it is pinched or hung in a log.

Use a wedge to remove pinched saw

Turn

saw OFF and use a plastic or

wooden wedge to force cut open

Overcutgng begins on the top side of the log

with the bottom of the saw against the log

When overcutfiog use _ight downward pres-

sure.

Undercutting involves cutting on the under-

side of the log with top of saw against the log.

When undercutting use light upward pres-

sure. Hold saw firmty and maintain control

The saw will tend to push back toward you.

_WARNING: Neverturnsawogside

down to undercut. The saw cannot be con-

trolled in this position.

Always make your first cut on the compres-

sion side of the log. The compression side of

the log is where the pressure of the log's

weight is concentrated.

First cut on compression side of Iog

Second cut

First cut on compression side of log

BUCKING WITHOUT A SUPPORT

• Overcut through 1/3 of the diameter of the

log.

• Roll the log over and finish with a second

overcut.

• Watch for logs with a compression side to

prevent the saw from pinching. Bee il-

Iustrabens for cutting logs with a compres-

sion side.

BUCKING USING A LOG OR

SUPPORT STAND

• Remember your first cut is always on the

compression side of the log.

(Refer to the illustraflons below for your

first and second cut)

• Your first cut should extend 1/3 of the

diameter of the log.

• Finish with your second cut.

Using a log for support

2r_dCut

1st Cut

2_ Cut _'P"2_

Using a support stand

2 nd Cut

LIMBING AND PRUNING

_iIWARNING: Be alert for and guard

against kickback Do not allow the moving

chain to contact any other branches or objects

at the nose of tile guide bar when limbing or

pruning. Ailowing such contact can result in

serious injury.

_ WARNING: Never climb into a free to

limb or prune. Do not stand on ladders, plat-

forms, a log, or inany position which can cause

you to lose your balance or control of the saw.

IMPORTANT POINTS

• Work slowIy, keeping both hands firmIy

gripped on the saw. Maintain secure footing

and balance.

• Watch out for sptingpoles. Springpoles are

smatl size limbs which can catch the saw

chain and whip toward you or pull you offbal-

ance. Use extreme caution when cutting

small size limbs or slender material.

• Be alert for springback. Watch out for

branches that are bent or under pressure.

Avoid being struck by the branch or the

saw when the tension in the wood fibers is

released.

• Keep a clear work area Frequently clear

branches out of the way to avoid tripping

over them.

LIMBING

• AIwayslimbatreeafferitiscutdown Only

then can limbing be done safely and prop-

edy.

• Leave the larger limbs underneath the felled

tree to support the tree as you work.

• Start at the base of the failed tree and work

toward the top, cutting branches and Iimbs

Remove small limbs with one cut.

• Keep the tree between you and the chain.

Cut from the side of the free opposite the

branch you are cutting

• Remove larger, suppor_ng branches with

the cutting techniques described in SUCK-

iNG WITHOUT A SUPPORT

• Always use an overcut to cut small and free-

iy hanging limbs. Undercu_ing could cause

limbs to fal} and pinch the saw.

PRUNING

_&WARNING: Umit pruning to limbs

shoulder height or below. Do not cut if

branches are h_gher than your shoulder. Get a

professional to do the job.

• Make your first cut b3 of the way through the

bottom of the limb.

• Next make a 2nd cut all the way through

the limb. Then cut a third overc ut leaving a

t to 2 inch (2 5 to 5 cm) collar from thetruck

of the tree

/ Second cut /_'

Third cxit_/

Co,lar _t_. First cut

_/ Pruning technique

_I_WARNING: Disconnect the spark

plug before performing maintenance except

for carburetor adjustments.

We recommend all service and adjustments

not Iisted in this manual be performed by an

authorized or Master Service Dealer

MAINTENANCE SCHEDULE

Check:

Fuel mixture level .... Before each use

Bar lubrication ....... Before each use

Chain tension ....... Before each use

Chain sharpness ..... Before each use

For damaged parts ... Before each use

For loose caps ...... Before each use

For loose fasteners... Before each use

For loose parts ...... Before each use

inspect and Clean:

Bar ................ Before each use

Complete saw ....... After each use

Air filter ............. Every 5 hours*

Chain brake ......... Every 5 hours*

Spark arresting screen

and muffler .......... Every 25 hours*

Replace spark plug . Yearly

Replace fuel filter ... Yearly

Hours of Operation -

Each hour of operation is approximately

2 tanks of fuel

AIR FILTER

CAUTION: Do not clean filter in gasoline

or other flammable solvent to avoid creating

a fire hazard or producing harmful evapora-

tive emissions.

Cleaning the air filter:

A dirty air filter decreases the Iife and perfor-

mance of the engine and increases fuel con-

sumption and harmfuI emissions. Always

clean your air filter after f O tanks of fuel or 5

hours of operation, whichever comes first

Clean more frequently in dusty conditions A

used air filter can never be completely

cleaned. It is advisable to replace your air fih

tar with a new one after every 50 hours of op-

eration, or annualIy, whichever comes first.

1. Loosen 3 screws on cylinder cover

2. Remove cylinder cover.

3. Remove air fiIter.

4. Clean the air fiIter using hot soapy water.

Rinse with clean cool water. Air dry

completely before reinstalling.

5. Ughtiy oil air fiIter before installing to im-

prove the efficiency of air filter Use

2-cycle engine oil or motor oil (SAE 30).

Squeeze excess oiI from filter

6. Reinstal_ air filter

7. ReinstalI cylinder cover and 3 screws.

Tighten securely.

INSPECT MUFFLER AND SPARK

ARRESTING SCREEN

As the unit is used, carbon deposits build up

on the muffler and spark arresting screen,

and must be removed to avoid creating a fire

hazard or affecting engine performance.

Replace the spark arresting screen if breaks

OCCUr

uffler Diffuser

spark

' r2: ti2g

•, o:v::e:rs

Body

CLEANING THE SPARK ARREST-

ING SCREEN

Cleaning is required every 25 hours of op-

eration or annually, whichever comes first.

1. Loosen and remove the 2 muffler cover

screws.

2 Removethe muffler cover (cover snaps

off muffler body).

3. Remove muffler diffuser and spark ar-

resting screen assembly. Notice the

orientation of these parts for reassem-

bling.

4. Clean the spark arresting screen with a

wire brush Replace screen if breaks are

found.

5. Replace any broken or cracked muffler

parts.

6 Reinstall diffuser and spark arresting

screen assembly with round holes fac-

ing up.

7 Reinstall muffler cover and 2 screws

Tighten securely

CARBURETOR ADJUSTMENT

,_&WARNING: Thechainwillbemov-

ingduring most of this procedure. Wear your

protective equipment and observe all safety

precautions. The chain must not move at idle

speed

The carburetor has been carefuIly set at the

factory. Adjustments may be necessary if

you notice any of the following conditions:

• Chain moves at idle See IDLE SREED-T

adjusting procedure.

• Saw wiil not idle See iDLE SPEED-T ad-

justing procedure.

Idle Speed-T

AI[ow engine to idle. If the chain moves, idle

is too fast. If the engine stalls, idle is too slow.

Adjust speed until engine runs without chain

movement (idle too fast) or stalling (idle too

slow). The idle speed screw is located in the

area above the primer bulb and is labeled T

• Turn idle speed screw (T) clockwise to in-

crease engine speed.

• Turn idle speed screw (T) counterclock-

wise to decrease engine speed.

If you require further assistance or are unsure

about performing this procedure, contact your

authedzed service dealer or cal

1-800-554-8723

BAR MAINTENANCE

If your saw cuts to one side, has to be forced

through the cut, or been run with an improper

amount of bar lubrication it may be neces-

sary to serviceyour bar. A worn bar will dam-

age your chain and make cutting difficult.

After each use, ensure ON/STOP switch is

in the STOP position, then clean nil sawdust

from the guide bar and sprocket hole

To maintain guide bar:

• MoveON/STOPswitohtothe STOP posi-

tion.

• Loosen and remove chain brake nuts and

chain brake. Remove bar and chain from

saw.

• Clean the oil holes and bar groove after

each 5 hours of operation.

Remove Sawdust From

Guide Bar G_o_F__

Oil Holes

• Burring of guide bar rails is a normal

process of rail wear Remove these burrs

with a flat file.

• When rail top is uneven, use a fiat file to re-

store square edges and sides

'_ File Rail Edges _ rL[]

and Sides

Square

Worn Groove Correct Groove

Replace guide bar when the groove is worn,

the guido bar is bent or cracked, or when exce-

ss heating or burring of the rails occurs If re-

placement is necessary, use onIy the guide bar

specified for your saw in the repair parts list or

on the decal located on the chain saw.

CHAIN SHARPENING

Chain sharpening is a complicated task that

requires speciaI tools We recommended

you refer chain sharpening to a professional

chain sharpener.

IGNITION TIMING

Ignition timing is fixed and nonadjustable.

SPARK PLUG

The spark plug should be replaced each

year to ensure the engine starts easier and

runs better

1. Loosen 3 screws on cylinder cover

2. Remove the cylinder cover

3. Pull off the spark plug boot.

g. Remove spark plug from cylinder and

discard.

5. Rep}ace with Champion RCJ-7Y spark

plug and tighten securely with a 3/4 inch

(19 mm) socket wrench. Spark plug gap

shouId be 0.025 inch (0.8 ram).

6. Reinstall the spark pIug boot.

7 Reinstall the cylinder cover and 3

screws. Tighten securely.

Screws Cylinder

STORAGE

WARNING: Stop engine and allow

to cool, and secure the unit before storing or

transporting in a vehicle. Store unit and fuel

in an area where fuel vapors cannot reach

sparks or open flames from water heaters,

electric motors or switches, furnaces, etc

Store unit with all guards in place. Position so

that any sharp object cannot accidentally

cause injury to passersby Store the unit out

of reach of children.

• Before storing, drain all fueI from the unit

Start engine and allow to run until it stops

• Clean the unit before stodng. Pay particu-

lar attention to the air intake area, keeping

tt free of debris. Use a mild detergent and

sponge to clean the plastic surfaces.

• Do not store the unit or fuelin a closed area

where fueI vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

• Store in a dry area out of the reach of chil-

dren.

CAUTION: _ _s important to prevent gum

deposits from forming in essential fuel system

parts such as the carburetor, f_el fi_ter, fuel

hose, or fuel tank during storage. A_cohol

blended fuels (cal_ed gasohol or using ethanol

or methano 9 can attract moisture which leads

to fuet mixture separation and formation of

acids during storage. Acidic gas can damage

the engine.

NEED ASSISTANCE?

Call 1-800-554-8723.

NEED SERVICE PART?

Contact your dealer or place of purchase.

TROUBLESHOOTING TABLE

_t, WARNING: Always stop unit and disconnect spark plug before performing alI of

the recommended remedies below except remedies that require operation ofthe unit

TROUBLE CAUSE REMEDY

Engine wiII not 1. Ignition switch off. f. Move ignition switch to ON

start or wil_ run 2. Engine flooded 2 See "Difficult Starting" in

oniy a few Operation Section.

seconds after 3. Fuet tank empty. 3 FiII tank with correct fuel mixture

starting. 4-.Spark plug not firing. 4 Install new spark plug.

5. Fuel not reaching 5 Check for dirty fuel filter; replace

carburetor Check for kinked or sp_it fuel line;

repair or replace

Engine wil_ f. Idie speed requires 1. See "Carburetor Adjustment" in the

not idle adjustment. Service and Adjustments Section.

properly. 2. Carburetor requires 2. Contact an authorized service dealer.

adjustment.

Engine will not f. Air filter dirty. 1. Clean or replace air fluter.

accelerate, 2. Spark plug fouled 2 Clean or replace plug and regap

lacks power, 3. Chain brake engaged 3 Disengage chain brake

or dies under 4. Carburetor requires 4 Contact an authorized service dealer

a load adjustment.

Engine t. Too much oi_ mixed with t Empty fuel tank and refill with

smokes gasoline correct fuel mixture.

excessively.

Chain moves 1. Idle speed requires t See "Carburetor Adjustment" in the

at idle speed, adjustment. Service and Adjustments Section.

g. Clutch requires repair. 2 Contact an authorized service dealer.

Poulan, a division of Husqvarna Outdoor

Products inc, warrants to the original con-

sumer purchaser that each new Poulan

brand gasoline chain saw is free from de-

fects in materia_ and workmanship and

agrees to repair or replace under this war-

ranty any defective gasoline chain saw as

foltows from the original date of purchase

1 YEAR - Parts and Labor. when used for

household purposes.

60 DAYS - Parts and Labor, when used for

commercial, professional, or income pro-

ducing purposes.

30 DAYS - Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does

not cover damage or liability caused by im-

proper handling, improper maintenance or

dilatation, or the use of accessories and/or

attachments not specifically recommended

by Poulan for this chain saw. This warranty

does not cover tune-up, spark plugs, filters,

starter ropes, chain sharpening, bars,

chains, and other parts which wear and re-

quire replacement with reasonable use dur-

ing the warranty period This warranty does

not cover predelivery setup, installation of

guide bar and chain, and normal adjust-

ments explained in the instruction manual

such as chain tension adjustments. This

warranty does not cover transportation

costs.

In the event you have a claim under this war-

ranty, you must return the product to an au-

thorized service dealer.

Sbeuid you have any unanswered questions

concerning this warranty, please contact:

Poulan, a division of Husqvama Outdoor

Products Inc.

1030 Stevens Creek Road

Augusta, GA 30907

1-800-554-6723

In Canada, contact:

Poulan

5855 Terry Fox Way

Mississauga,Ontario LhV3E4

Giving the model number, serial number and

date of purchase of your product and the

name and address of the authorized dea_er

from whom it was purchased.

THIS WARRANTY GWES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY PROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED_

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN tMPUEDWAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CON-

SEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATIONS OR EXCLUSION

MAY NOT APPLY TO YOU.

This is a limited warranty within the meaning

of that term as defined in the Magnuson-

Moss Act of 1975.

The policy of Pou}an is to continuously im-

prove its products Therefore, Poulan re-

serves the right to change, modify, or discon-

tinue models, designs, specifications, and

accessories of al_products at any time with-

out notice or obIigation to any purchaser.

YOUR WARRANTY RIGHTS AND OBLIGA-

TIONS: The U. S. Environmental Protection

Agency, Environment Canada and Poulan are

pleased to explain the emissions control sys-

tem warranty on your year 2007 and later small

off-road aegina. Poulan must warrant the

emission control system on your small off-road

engine for the periods of time listed below pro-

vided there has been no abuse, neglect, or im-

proper maintenance of your small off-road en-

gine. Your emission control system includes

parts such as the carburetor and the ignition

system. Where a warrantable condition exists,

Poufan will repair your small off-road engine at

no cost to you. Expenses covered under war-

runty include diagnosis, parts and labor

MANUFACTURER'S WARRANTY COVER-

AGE: Ifany emissions related part on your en-

gine (as listed under Emissions Control War-

ranty Parts List) is defective or a defect in the

materials or workmanship of the engine

causes the failure of such an emission related

part, the part will be repaired or replaced by

Poufan.

OWNER'S WARRANTY RESPONSIBILI-

TIES: As the small off-road engine owner,

you are responsible for the performance of

the required maintenance listed in your in-

struction manual Poulan recommends that

you retain all receipts covering maintenance

on your smalI off-road engine, but Poutan

cannet deny warranty solely for the lack of

receipts or for your failure to ensure the per-

formance of nil scheduled maintenance. As

the small off-road aegina owner, you should

be aware that Poulan may deny you warran-

ty coverage if your sma}l off- road engine or a

part of it has failed due to abuse, neglect, im-

proper maintenance, unapproved modifica-

tions, or the use of parts not made or ap-

proved by the original equipment

manufacturer. You are responsible for pre-

senting your smal_ off-road engine to an

PouIan authorized repair center as soon as a

problem exists. Warranty repairs should be

completed in a reasonable amount of time,

not to exceed 30 days. If you have any ques-

tions regarding your warranty rights and re-

sponsibiIities,youshouldcontactyournear-

estauthorizedservicecenterorcallPoulan

at1-800-554-8723.WARRANTYCOM-

MENCEMENTDATE:Thewarrantyperiod

beginsonthedatethesmalloff-roadengine

ispurchased.LENGTHOPCOVERAGE:

ThiswarrantyshalIbeforaperiodoftwo

yearsfromtheinitia_dateofpurchase.

WHATISCOVERED: REPAIR OR RE-

PLACEMENT OF PARTS. Repair or re-

placement of any warranted part will be per-

formed at no charge to the owner at an

approved Poulan servicing center. If you

have any questions regarding your warranty

rights and responsibilities, you should con-

tact your nearest authorized service center

or caII PouIan at 1-800-554-8723. WAR-

RANTY PERIOD: Any warranted part which

is not scheduled for replacement as required

maintenance, or which is scheduled only for

regular inspection to the effect of "repair or

repIace as necessary" shall be warranted for

2 years. Any warranted part which is sched-

uled for replacement as required mainte-

nance shall be warranted for the period of

time up to the first scheduled replacement

point for that part. DIAGNOSIS: The owner

shal_ not be charged for diagnostic labor

which leads to the determination that a war-

rented part is defective if the diagnostic work

is performed at an approved Poulan servic-

ing center

CONSEQUENTIAL DAMAGES: Pou_an

may be liable for damages to other engine

components caused by the failure of a war-

ranted part still under warranty. WHAT IS

NOT COVERED: AII failures caused by

abuse, neglect, or improper maintenance

are not covered. ADD-ON OR MODIFIED

PARTS: The use of add-on or modified parts

can be grounds for disallowing a warranty

claim Poulan is not liable to cover failures of

warranted parts caused by the use of add-

on or modified parts. HOW TO FILE A

CLAIM: If you have any questions regarding

your warranty rights and responsibilities,

you should contact your nearest authorized

service center or calI Pou_an at

1-800-554-6723 WHERE TO GET WAR-

RANTY SERVICE: Warranty services or re-

pairs shall be provided at aH PouIan service

centers Call t-800-554-8723. MAINTE-

NANCE, REPLACEMENT AND REPAIR

OF EMISSION RELATED PARTS: Any

Poulan approved replacement part used in

the performance of any warranty mainte-

nance or repair on emission related parts will

be provided without charge to the owner if

the pert is under warranty. EMISSION CON-

TROL WARRANTY PARTS LIST: Carbure-

tor, Ignition System: Spark Plug (covered up

to maintenance scheduIe), Ignition Module.

MAINTENANCE STATEMENT: The owner

is responsible for the performance of all re-

quired maintenance as defined in the in-

strucSon manual

The informationonthe product labet indicates which standard your engine is certified.

Example: (Year) EPA Phase f or Phase 2 and/or CALIFORNIA.

This engine is certified to be emissions compliant for the fo}lowing use:

_ Moderate (50 hours)

[] intermediate (125 hours)

[] Extended (300 hours)

Poulan 2155 User manual

Brand: Poulan

Model: 2155

Category: Power chainsaws

Type: User manual

This manual is also suitable for

Download PDF

report

Poulan 2155 User manual

This manual is also suitable for

Poulan 2155 User manual

Related papers

Other documents