Gamber-Johnson MAX3 Visor Camera Specification

INSTALLATION INSTRUCTIONS

Product Revision Form

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Rev.D

INST-513

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Printing Spec: PS-001

VISOR MOUNT,2 UNIT,SINGLE SIDE ATTACHMENT

7160-0312, 7160-0373

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

TheVisorMount,2Unit,S ingleSideAttachmentprovidestheuserwiththecapabilitytosecureamobile

cameraandamonitortothepassengersidevisor.EachsystemincludestwoMax

allaxisknucklesthat

allowtheusertoorientthemonitorandcamera inseveralpositions.Inaddition,thesystemisequipped

withtworubberpadsandseveralmountingholestoensurethecameraandmonitorareheldsecureand

firm.

ToolsNeeded MaterialNeeded

5/64‐inHexwrench(Allenwrench) #10Selfdrillingscrew

3/16‐inHexwrench(Allenwrench)

 #8x1.00sheetmetalscrewfor2010+Charger



Installation

1. Removethepassengersidevisorretainerclipnearthecenterofthevehicle.Refertofigure1.

2. SecuretheVisorMounttotheheadliner usingthevisorretainerandtwoadditionalselftapping

fasteners.

a. Selftappingfasteners arenotsup plied.

b. Caution:Selftappingfastenersthataretoo

longmaygothroughroofofvehicle.

3. Securethecameratothefrontcamerabracketusing(2)¼‐20x.50socketbuttonheadcapscrew,

(2)¼‐inlockwasher,and(4)¼‐innylonflatwashers.Refertofigure2.

4. Securethemonitortothemonitor

bracketusing har dwaresuppliedbymonitormanufacturer.

Refertofigure3forholepatternsavailable.

5. Positionthecameraandmonitorasdesired.

6. Inserttwoandtightenall#10‐32socketheadsetscrewstolocktheMax

knucklesinplace .Referto

figure2.



Sheet 1 of 2

Figure1.SecureVisorMountwithpassengersidevisorretainer.

Figure2:Assemblecamerawith1/4‐infasteners

Figure3:Monitorbracketholepatterns

11/2

13/16

129/32

15/16 q

19/16

111/32

Sheet 2 of 2

2X1/4‐20x.50socketbutton

headcapscrew

2X1/4‐inlockwasher

4X1/4‐innylonflatwasher

Figure4:InstalledVisorMount

#10‐32sockethead

setscrew

#10‐32sockethead

setscrew

Gamber-Johnson MAX3 Visor Camera Specification

Related papers

Other documents