1
2
3
4
8
7
6
5
10
9
11
Qty: 2
Qty: 2
CAUTION
!
• Failure to install can in clip will cause hot
grease to drip from bottom of grill with
risk of fire or property damage.
•Hang grease clip from center of grill bottom.
•Use an empty soup can (not included) to hang
from grease clip.
LP tank is sold separately. Fill and leak check before
attaching to grill and regulator.
See Use and Care to perform the “Burner Flame Check”
and important safety instructions before using
CAUTION
!
Tank collar opening must face to front of cart once tank is
attached.
Failure to install tank correctly may allow gas hose to be
damaged in operation, resulting in the risk of fire.
Place Bottom Shelf and Legs as shown.
After assembling tighten all Wing Nuts.
2 Carriage Bolts and Wing Nuts
Left Side: Use Upper Hole ONLY)(
to attach 1 Carriage Bolt and Wing Nut
Qty: 6
Qty: 6
Items to Assemble:
6 Carriage Bolts
6 Wing Nuts
Right Side:
(Use both Upper and Lower Holes)
Items to Assemble:
2 Wheel Assemblies
2 Leg Extenders
2 Hitch Pins
Hitch Pin - Qty: 2
Qty: 2
Items to Assemble:
1 Grill Bottom with Control Panel
1 Heat Shield
4 Carriage Bolts
4 Wing Nuts
1 Condiment Basket
Qty: 4
Qty: 4
Items to Assemble:
2 Shelves
8 Wing Nut Screws
Items to Assemble:
1 Vaporiser Bar
1 Grate
1 Charcoal Pan or Grate Holder
Push Vaporiser Bar
down onto rest in
Grill Bottom
Items to Assemble:
1 Grill Lid
2 Hinge Pins
2 Hitch Pins
1 Logo Plate
1 Handle
3 Wing Nuts
1 Heat Indicator
1 Heat Indicator Bracket
A
B
C
D
E
F
G
H
Qty: 3
Items to Assemble:
1 Panel
2 Push Pins
1 Wire Shelf
Items to Assemble:
1 Grease Clip
1 Tank Wire Support Bracket
Grate Rests
461833803
Rear View
of Grill
Correct position of LP tank
and tank wire support
bracket after grill assembly
A.
B
Place tabs into slots on bottom shelf
. Place wire shelf in 3rd hole from top
A
B
ASSEMBLER NOTE: Assemble front panel first by placing tabs into slots on bottom shelf
before inserting wire shelf
Attach hitch pins to axle rod on wheel assembly
after pushing through leg and shelf
Wing Screw -Qty: 8
C
A Insert leg on warming rack into
grill bottom
B Place U-shaped wires on back of
warming rack over straight wire.
D Flex leg wire down and forward to secure on hook of warming rack.
D
B
C
Item to Assemble:
1 Warming Rack
1 Leg Wire
Place leg wire into U-shaped
wire on front of warming rack.
Straight Wire
Using the Charcoal Pan
Remember to remove the warming rack and cooking grate.
A
B Rotate grate support wires up and insert into
holes on charcoal pan
Insert channels before placing pan in grill bottom
D Rotate warming rack
leg wire to back of grill
bottom
C Place warming rack
in upper position
on the wire grate
supports and the tray
onto channels in
grill bottom.
Top casting shown is for illustration only. It may not necessarily
be the one that is packaged with your grill.
Slide charcoal pan holder or
grate holder onto bottom
casting
A
B
B
C
C
D
E
F
F
F
G
Attach clips on straight wire. Place wire into lower hole
on lid. Slide clips to lid sides.
Remove Vaporizor Bar and Cooking Grid
When Installing Charcoal
Pan or Grate Holder
Attach handles between second and third wire
from ends. Hook end of handle over back and
pull to hook over front wire.
Items To Assemble:
2 Warming Rack Handles
Items To Assemble:
1 Straight Wire
2 Clips
H
Tank Sold Separately. Use Only With
Tank Equipped With Overfill Protection
Device.
/