Motorola PTX600 User manual

Brand: Motorola

Model: PTX600

Category: Two-way radios

Type: User manual

PTX600

User Manual

PTX600_UserBook Page 1 Thursday, July 3, 1997 9:54 AM

(ii)

Vol - Off

VHF

PTX 600

Vol - Off

VHF

PTX 600

✱

PTX600_UserBook Page ii Thursday, July 3, 1997 9:54 AM

(iii)

Illust.3

Illust.2

Illust.1

PTX600_UserBook Page iii Thursday, July 3, 1997 9:54 AM

(i)

2-YEAR LIMITED WARRANTY

FOR RADIO

We thank you for purchasing our Motorola radios. These

radios are manufactured according to the highest quality

standards set and are backed by Motorola’s two (2) year

warranty. The rechargeable Motorola supplied batteries

have a one (1) year warranty. Kindly approach your dealer

for more information.

Motorola warrants its radios and batteries against defects

in material and workmanship under normal use and serv-

ice for the period stated above.

Motorola recommends that you use Motorola supplied

accessories and batteries in connection with the radio.

We would also advise you against attempting any modiﬁ-

cations or repairs or any other form of unauthorised serv-

ice to your radio.

Should you have any queries, please contact:

Singapore - Telephone/Fax: (65) 2812053/

2874181

Beijing - Telephone/Fax: (86-10) 68438231/

4610277

Please see inside back cover for more

information.

Fill in the details of your radio below for your

own reference:

Model Name/No.:

Serial Number:

Date of Purchase:

Dealer Name:

Address:

Telephone:

PTX600_UserBook Page i Thursday, July 3, 1997 9:54 AM

English

PTX600 User Guide

Page:

General Information............................................ 2

Radio Care ......................................................... 2

Safety Information .............................................. 2

Radio Controls.................................................... 3

Audio Tones........................................................ 4

Display Icons...................................................... 4

Getting Started................................................... 5

Turning the radio On/Off............................... 5

Outgoing Calls.................................................... 5

Shortform Dialling......................................... 5

Dedicated Calls............................................. 6

Manual Dialling............................................. 6

Keypad Edit................................................... 6

Last Number Redial...................................... 6

Incoming Calls.................................................... 6

Call in Absence............................................. 7

Call Diversion ............................................... 7

Cancelling a Call ................................................ 8

Ending a Call...................................................... 8

Page:

Special Calls .......................................................8

Status Calls ...................................................8

Emergency Calls ...........................................9

Priority Calls..................................................9

Broadcast Calls .............................................9

DTMF Dialling .....................................................9

Conventional Mode .............................................9

Accessories and Battery Care ..........................10

Fitting the Belt Clip ......................................10

Fitting/Removing Battery.............................10

Operating Time............................................10

Battery Tips .................................................11

Intrinsically Safe Radio Information...................12

Computer Software Rights................................14

Limited Warranty ...............................................15

Contents

2-Year Warranty

PTX600_UserBook Page 1 Thursday, July 3, 1997 9:54 AM

English

General Information

This user guide covers the operation of the PTX600

Series portable radios used on MPT1327 Trunked

Radio Systems. Please note that the location of the

system may affect the types of call which are

available. Please consult your network manager for

further information.

This user guide describes the operation of radios

with and without a keypad/display. On radios

without

a keypad/display the different types of call

described can only be selected via the Shortform

Dial Selector (2) or the Base Call Button (7).

Radio Care

Avoid any physical abuse of the radio such as

carrying the radio by its antenna.

Wipe the battery contacts with a lint free cloth to

remove dirt, grease or any other material which may

prevent a good electrical contact of the battery

terminals to the radio.

The accessory connector is ﬁtted with a protective

cap which should be left in place when the

connector is not in use.

The radio housing should be cleaned with a cloth

dampened with clean water, a mild liquid soap

solution or isopropyl alcohol.

Caution:

The use of chemicals such as detergents, alcohol

(except isopropyl), aerosol sprays, and petroleum

products may be harmful and damage the radio

housing.

Safety Information

During normal use, this radio will subject you to

radio energy substantially below the level where any

kind of harm is reported.

The handheld portable radio should be held in a

vertical position with the microphone 2.5 to 5 cm

(1 to 2 inches) from the mouth and the antenna

should be kept 2.5 to 5 cm (1 to 2 inches) from

the head or body when transmitting. For body

worn operation, the antenna should be kept at

least 2.5 cm (one inch) from the body when

transmitting.

DO NOT

hold the transmit (PTT) key in when not

actually desiring to transmit.

DO NOT

allow children to play with any radio

equipment containing a transmitter.

DO NOT

operate the radio near unshielded elec-

trical blasting caps or in an explosive atmos-

phere.

DO NOT

dispose of the battery on a ﬁre as it

may explode (see battery tips).

General Information/Radio Care/Safety Information

2-Year Warranty

PTX600_UserBook Page 2 Thursday, July 3, 1997 9:54 AM

English

Radio Controls

The numbers refer to the illustrations on page (ii).

On/Off Volume Control

Turns the radio on/off and adjusts the volume

level.

Shortform Dial

Channel Selector

(Conventional Mode)

(16 position)

Three Colour Indicator

(LED)

Green, Flashing: Scanning

Yellow, Slow Flashing: Call setup request

acknowledged by controller

Yellow, Fast Flashing: Call acknowledged by

recipient or Emergency call

Yellow, Continuous: Radio On Trafﬁc Channel

Red, Continuous: Radio Transmitting

Red, Flashing: Channel Busy (Conventional)

Accessory Connector

Connector for external headset or remote

speaker/microphone. Must be covered by

attached cap when not in use.

Antenna Connector

Clear Button

For cancelling a call, clearing down at the end of

a call or Carrier Monitor (Conventional).

Base Call Button

For making calls to preprogrammed numbers.

Transmit (PTT) Button

Push to talk, release to listen.

Press continuous when using DTMF dialling.

Numeric Display

Eight characters and icons.

Backlit when any button pressed.

10.

Edit Key/Call Clear

For correcting keypad entries, clearing

calls on a trafﬁc channel and deselecting

call in absence interrogate mode.

11.

Keypad Up/Down

Used to select call in absence

interrogate mode and scroll through the

call in absence stack.

12.

Status Key

For sending status messages.

13.

Keypad

0 to 9 for entering digits.

for sending a call.

call modiﬁer for priority, broadcast,

emergency and status calls.

✱

Radio Controls

2-Year Warranty

PTX600_UserBook Page 3 Thursday, July 3, 1997 9:54 AM

English

Audio Tones

High pitched tone Low pitched tone

Self test: Sounded on power up

Tone A: Call clear indication

Tone B: Trafﬁc channel allocated

and PTT/Mic/

Loudspeaker enabled.

Tone C1: System busy

Tone C2: Unavailable

Tone C3: Called party busy

Tone C4: Invalid number

Tone D: Call set up in progress,

wait for further

indications

Tone E: Incoming call, press PTT,

then wait for further

indications.

Tone F: Transaction conﬁrmed,

called unit will call

back.

Tone G: Look at display for call set

up or system information.

Tone H: Invalid entry

Tone I: Low battery warning

Key click: Conﬁdence tone when

any key pressed/speech

limitation warning

Fail tone: Battery low/hardware

error or call timed out

(conventional mode)

Display Icons

The icons which appear on the display are:

Scanning

Control Channel Conﬁrmed

Call In Absence Received

Indicates low transmit power selected

Battery Low

Loudspeaker Open

Conventional Mode Only

Carrier Monitor Selected

Tx Frequency = Rx Frequency

Audio Tones/Display Icons

2-Year Warranty

PTX600_UserBook Page 4 Thursday, July 3, 1997 9:54 AM

English

Getting Started

Turning the Radio On/Off

Turn the radio on by rotating the combined ON/OFF/

VOLUME control (1) clockwise. The radio then

enters a self test routine. During the test the display

will be activated, the self test tone will sound, and

the LED will light green. If the radio fails the self test

a continuous low tone will sound and the LED will

ﬂash red or yellow. The radio is turned off by rotating

the volume control anticlockwise past the click stop.

Note:

If the radio fails the self test routine, consult

your dealer.

When the self-test is complete the radio displays its

identity number (keypad/display radio only).

After this the radio will scan the system access with

the LED on the top of the radio ﬂashing green and

the scanning icon lit.

When a control channel is acquired, the green LED

will go off and the scanning icon will be replaced by

the registered icon . This is known as the IDLE

STATE. The display will also show you your radio ID

number to the right of the display.

The radio must be in this state before you can make

or receive a call.

Outgoing Calls

The radio is capable of making a variety of calls

including calls to individual radios or group of radios.

The radio can make calls by using Shortform

Dialling, or Dedicated Calls. Keypad radios can

also make calls using Manual Dialling.

When making a call note that the radio has a

maximum transmit timer. This appears on the right

of the display, replacing your radio ID. This prevents

excessive use on the trafﬁc channel by returning the

radio to the IDLE STATE (effectively cancelling the

call). Ten seconds before the radio returns to the idle

state the keyclick tone sounds.

Shortform Dialling

When the radio is in the IDLE STATE shortform

dialling may be used. This allows quick access to a

maximum of 16 preprogrammed numbers, with only

the ﬁrst eight digits visible, using the shortform dial

position selector (2).

Depending on the way your radio is programmed,

the radio will display the number to be dialled.

The call request is sent by either pressing the PTT

key (8) or key.

Getting Started/Outgoing Calls

2-Year Warranty

PTX600_UserBook Page 5 Thursday, July 3, 1997 9:54 AM

English

If the dial selector (2) is moved, but no call request is

sent, the display will be held until the tone H sounds.

The display will then revert to the IDLE STATE.

Note:

When using the keypad radio, if the shortform

dial number is displayed, it may be edited as

described in the

Keypad Edit

section.

Dedicated Calls

Hold the Base Call Button (7) down for a

preprogrammed period to make a call to a

preprogrammed number. The number will then be

displayed and the conversation can go ahead.

Manual Dialling (Keypad Radios only)

To make a call enter the telephone number, the

identity of the radio or group of radios via the

keypad, e.g. “210” followed by or PTT.

Keypad Edit (Keypad Radios only)

Any number shown in the display may be edited

before a call is initiated. Enter this mode by pressing

(10). Press again to delete the last digit

and enter the correct number. If is pressed

during a call, the call will end.

Last Number Redial (Keypad Radios only)

The last number the radio dialled is stored in the

memory of the radio. For status calls only the called

number will be stored, not the status message.

Partially entered numbers are also stored.

Incoming Calls

There are two types of systems that the radio may

be used on, Off Air Call Set Up (OACSU) and Full

Off Air Set Up (FOACSU).

If you are in any doubt about which system you are

operating on, consult your dealer.

Receiving a call on an OACSU system -

When the radio is called tone D will sound and the

LED and display ﬂashes. This will then be followed

by tone B.

Receiving a call on an FOACSU system -

When the radio is called tone E will sound and the

LED and display ﬂashes.

Press either the PTT or key to accept the call.

Tone D will sound until a trafﬁc channel is

allocated, then tone B sounds.

Note:

The system may have a limited call time and

the call may be terminated automatically if this call

time is exceeded.

Outgoing Calls/Incoming Calls

2-Year Warranty

PTX600_UserBook Page 6 Thursday, July 3, 1997 9:54 AM

English

Call In Absence

Call in Absence only applies to keypad/display

radios, if set in radio personality, consult your

network manager.

If a call is not answered within a preprogrammed

amount of time, the call is stored by the radio.

Up to 5 calls can be stored. If the same radio calls

more than once, the call is only stored once. When 5

calls have been stored by the radio the sixth call

received overwrites the ﬁrst.

When a call has been stored by the radio, tone G

will sound every ten seconds and the display will

show the identity of the calling party with the stack

index displayed on the left. The call in absence icon

will be lit to indicate there is a call in the stack.

To view/interrogate the calls in the stack press the

up or down scroll key or (11) and then use

these keys to view any other numbers in the stack.

The most recent call stored by the radio will be

displayed ﬁrst. Select the up/down scroll keys (11) to

display any other calls in the stack. If the stack is

empty tone H sounds.

To exit the call in absence interrogate mode press

the keypad edit button (10).

Press either the PTT or key to make a call. The

number stays in the stack until the clear button (6) is

pressed, is dialled, or the personality of the

radio is changed.

Note:

The calls in the stack are deleted when the

radio is turned off. It is not possible to call back

status calls.

Call Diversion

Incoming speech calls or status calls can be

diverted either from your radio (initiated by pressing

) or from another radio (initiated by

pressing ). On radios without a keypad

Call Diversion/Cancellation may be programmed in

the shortform dial list. Please contact your network

manager for further information.

When the radio is in the IDLE STATE, call diversion

can be initiated by pressing:

(or ) to divert all calls

(or ) to divert

speech calls/status calls

followed by the ID of the receiving radio and .

Examples:

Pressing

will divert all calls from your radio to the radio with

the ID "234".

✱

Incoming Calls/Call In Absence/Call Diversion

2-Year Warranty

PTX600_UserBook Page 7 Thursday, July 3, 1997 9:54 AM

English

Pressing:

will redirect all calls to the radio with the ID "234" to

the radio with the ID "432".

If a call is made to a radio whose calls are currently

being diverted, tone D will sound.

A call will then automatically be set up to the radio

which is receiving the diverted calls.

Cancelling Call Diversion (Keypad Radios)

Cancel a call diversion by pressing or

, followed by if necessary, and

"ID" .

To cancel calls directed to your radio, press

, followed by , if necessary.

Cancelling Calls

At any time while setting up a call it may be

cancelled by pressing the clear button (6) or by

dialling .

Ending Calls

A call should always be ended by pressing

key(10), clear button (6) or by dialling .

Special Calls

Status Calls

A status is a code for transmitting prearranged

messages, e.g. status “5” may indicate “return to

base”. When the radio receives a status call tone G

will sound.

For radios with a keypad status calls may be

initiated in two different ways, via the status key

(12) or manually via the keypad.

On radios without a keypad, status calls can only be

made if they are preprogrammed into the radio on

the shortform dial selector (2).

In order to make a status call via the status key,

choose the desired address as described in

Outgoing Calls

. Then press the key (12),

followed by two status digits.

The status number may be edited by using the edit

key (10), please refer to

Keypad Edit

To initiate a status call via the keypad enter

then enter the status e.g. “05” followed by and

the desired address. In both cases the call is

handled as described in

Outgoing Calls

✱

Incoming Calls/Cancelling Calls/Ending Calls/Special Calls

2-Year Warranty

PTX600_UserBook Page 8 Thursday, July 3, 1997 9:54 AM

English

Emergency Calls

An emergency call allows you the highest form of

priority calling and will normally take precedence

over all other calls. An emergency call can be

initiated either by pressing the Base Call Button (7)

for a preset period of time, to make a call to a

preprogrammed emergency number, or by dialling

the number, preﬁxing the required number by

. The call is then initiated as previously

described.

Priority Calls

A priority call allows you to gain priority over other

users of the system when requesting a call. Priority

calls are indicated by preﬁxing the required number

by . The call is then initiated as

previously described.

Broadcast Calls

A broadcast call allows you to make broadcast calls

to groups of radios. Broadcast calls are indicated by

preﬁxing the required number by .

The call is then initiated as previously described.

Note that on a broadcast call, only the calling radio

can talk and there is no indication that any units

have received the call.

DTMF (Keypad radio only)

DTMF means Dual Tone Multi Frequency (the same

as a telephone) and is used when the radio is

required to operate in a radio system with an

interface to telephone systems.

To generate the DTMF tones press and hold the

PTT (8) while entering the desired number, please

contact your network manager for further

information.

Conventional Mode

In the conventional mode the radio operates as a

standard two-way radio.

To switch from trunked mode to conventional mode,

rotate the shortform dial selector knob (2) to a

preset conventional channel. Up to four of the

sixteen channels may be pre-programmed for

conventional operation - please contact your

network manager for further information.

To switch back to trunked mode, rotate the

shortform dial selector knob (2) to a non-

conventional channel.

Note:

When switching between modes,

DO NOT

operate the radio until the self-test tone is sounded.

Prior to transmission always make sure that the

channel is free (red LED not ﬂashing). Press the

PTT key (8) to transmit, release it to listen. The red

✱

Special Calls/DTMF Dialling/Conventional Mode

2-Year Warranty

PTX600_UserBook Page 9 Thursday, July 3, 1997 9:54 AM

English

LED lights while the radio transmits and ﬂashes if

the channel is busy.

Some channels may be monitored for activity by

pressing the clear button (6). The icon will be lit until

the channel is changed or the clear button (6) is

pressed again.

In the conventional mode the radio is equipped with

a maximum transmit duration timer. This is

programmed to start whenever the PTT is pressed.

Tone G sounds ﬁve seconds before the transmitter

is switched off. If the timer expires whilst still

transmitting, transmission will cease and a

continuous fail tone will sound until the PTT is

released.

Accessories and Battery Care

Fitting Belt Clip

Refer to illustration 1 on page (iii).

To ﬁt the belt clip, slide it into the mounting rails on

the back of the radio and press it downwards until it

latches into place. To remove the belt clip, lift the

release tab by inserting a key or coin between the

release tab and the back of the radio. Press the belt

clip upwards until it is completely disengaged from

the radio.

Fitting/Removing Battery

Refer to illustrations 2 and 3 on page (iii).

To ﬁt the battery, slide it into the control rails about 1/

2 an inch (2 cm) from the top of the radio and slide it

towards the top until the battery latch has engaged.

Before removing the battery,

turn off the radio

Press the battery latch towards the front of the radio,

slide the battery down about 1/2 an inch (2 cm) and

lift it away from the radio.

Note:

The battery must be charged before initial

use. (For approximately 16 hours)

Operating Time

The operating time depends on the battery capacity,

transmit power combined with the frequency band,

and the duty cycle.

When the battery voltage runs low the battery icon

will appear on the display (display radios only)

and the low battery warning tone will sound

repeatedly for 60 seconds.

The power level in trunked mode can be adjusted on

the keypad radio which will save the battery life. To

toggle between high and low power levels enter

“14 ”. The display indicates the power level

selected by displaying the LO icon when low power

is selected.

Fitting Belt Clip/Fitting Battery/Operating Time

2-Year Warranty

PTX600_UserBook Page 10 Thursday, July 3, 1997 9:54 AM

English

Battery Tips

initialize new batteries that have been stored for

prolonged periods by charging overnight (16 hours)

charge batteries every 6 months during prolonged

storage.

use a battery for at least 4 hours prior to recharg-

ing. Remember, each time the battery is charged, one

cycle of life is used, and a battery has a limited number

of life cycles.

Do allow the battery to reach room temperature (at

least 1 hour) before placing it in the charger. Charge

Temperature Range: +5°C to +50°C.

Do take batteries out of a charger when they are fully

charged. Batteries allowed to remain in the charger for

extended periods lose valuable cycle life.

Do choose the right battery for every application.

Motorola offers a variety of batteries with different

sizes, capacities, and environmental use conditions.

Do dispose of used batteries properly and never

dispose of them in ﬁre.

Do not charge a hot battery; if a battery is hot at the

beginning of charge, charge efﬁciency will be greatly

reduced. Nickel cadium batteries are most efﬁciently

charged at room temperature (25°C).

Do not fast charge a cold battery. Charging a cold bat-

tery can cause excessive internal pressures, cell leak-

age, and catastrophic failure.

Do not force discharge nickel cadium batteries beyond

on volt per cell. Excessive deep discharge can signiﬁ-

cantly reduce battery life.

Do not use chemical cleaners to clean batteries.

Clean batteries only with a mild soap and dry

thoroughly with a cloth.

Remember......Conserve Battery Life Cycles!

Any secondary battery has a limited number of cycles;

each time the battery is charged and discharged,

one cycle of battery life is used.

Battery Tips

2-Year Warranty

PTX600_UserBook Page 11 Thursday, July 3, 1997 9:54 AM

English

Intrinsically Safe Radio Information

FMRC Approved Equipment

Anyone intending to use a radio in a location where

hazardous concentrations of ﬂammable material

exist (hazardous atmosphere) is advised to become

familiar with the subject of intrinsic safety and with

the National Electric Code NFPA 70 (National Fire

Protection Association) Article 500

(hazardous[classiﬁed] locations).

An Approval Guide, issued by Factory Mutual

Research Corporation (FMRC), lists manufacturers

and the products approved by FMRC for use in such

locations. FMRC has also issued a voluntary

approval standard for repair service (“Class Number

3605”).

FMRC Approval labels are attached to the radio to

identify the unit as being FM Approved for speciﬁed

hazardous atmospheres. This label speciﬁes the

hazardous Class/Division/Group along with the part

number of the battery that must be used. Their

Approval mark is shown below.

Warning

Do not operate radio communications equipment in a

hazardous atmosphere unless it is a type especially

qualiﬁed (e.g. FMRC Approved) for such use. An

explosion or ﬁre may result.

Do not operate the FMRC Approved Product in a haz-

ardous atmosphere if it has been physically damaged

(e.g. cracked housing). An explosion or ﬁre may result.

Do not replace or charge batteries in a hazardous

atmosphere. Contact sparking may occur while install-

ing or removing batteries and cause an explosion or

ﬁre.

Do not replace or change accessories in a hazardous

atmosphere. Contact sparking may occur while install-

ing or removing accessories and cause an explosion

or ﬁre.

Do not operate the FMRC Approved Product unit in a

hazardous location with the accessory contacts

exposed. Keep the connector cover in place when

accessories are not used.

Do not disassemble the FMRC Approved Product unit

in any way that exposes the internal electrical circuits

of the unit.

Turn the radio off before removing or installing a bat-

tery or accessory.

Radios must ship from the Motorola manufacturing

facility with the hazardous atmosphere capability

and FM Approval labeling. Radios will not be

“upgraded” to this capability and labeled in the ﬁeld.

APPROVED

Intrinsically Safe Radio Information

2-Year Warranty

PTX600_UserBook Page 12 Thursday, July 3, 1997 9:54 AM

English

A modiﬁcation changes the unit’s hardware from its

original design conﬁguration. Modiﬁcations can only

be done by the original product manufacturer at one

of its FMRC audited manufacturing facilities.

Warning: Failure to use an FMRC Approved

Product unit with an FMRC Approved battery or

FMRC Approved accessories speciﬁcally approved

for that product may result in the dangerously

unsafe condition of an unapproved radio

combination being used in a hazardous location.

Warning: Unauthorized or incorrect modiﬁcation of

an FMRC Approved Product unit will negate the

Approval rating of the product.

Repair of FMRC Approved Products

NOTE: REPAIRS FOR MOTOROLA FMRC

APPROVED PRODUCTS ARE THE

RESPONSIBILITY OF THE USER.

You may want to consider using a repair facility that

operates under 3605 repair service approval.

Warning: Incorrect repair or relabeling of any

FMRC Approved Product unit could adversely affect

the Approval rating of the unit.

Warning: Use of a radio that is not intrinsically safe

in a hazardous atmosphere could result in serious

injury or death.

FMRC’s Approval Standard Class Number 3605 is

subject to change at any time without notice to you,

so you may want to obtain a current copy of 3605

from FMRC. Per the July, 1995 publication of 3605,

some key deﬁnitions and service requirements are

as follows:

Repair

A repair constitutes something done internally to the

unit that would bring it back to its original condition

Approved by FMRC. A repair should be done in an

FMRC Approved facility.

Items not considered as repairs are those in which

an action is performed on a unit which does not

require the outer casing of the unit to be opened in a

manner which exposes the internal electrical circuits

of the unit. You do not have to be an FMRC

Approved Repair Facility to perform these actions.

Relabeling

The repair facility shall have a method by which the

replacement of FMRC Approval labels are

controlled to ensure that any relabeling is limited to

units that were originally shipped from the

Manufacturer with an FM Approval label in place.

FMRC Approval labels shall not be stocked by the

repair facility. An FMRC Approval label shall be

ordered from the original manufacturer as needed to

Intrinsically Safe Radio Information

2-Year Warranty

PTX600_UserBook Page 13 Thursday, July 3, 1997 9:54 AM

English

repair a speciﬁc unit. Replacement labels may be

obtained and applied by the repair facility providing

satisfactory evidence that the unit being relabeled

was originally an FMRC Approved unit. Veriﬁcation

may include, but is not limited to: a unit with a

damaged Approval label, a unit with a defective

housing displaying an Approval label, or a customer

invoice indicating the serial number of the unit and

purchase of an FMRC Approved model.

Do Not Substitute Options or Accessories

The communications equipment package that

Motorola submits to FMRC for testing and approval

is tested as a system that consists of the

communications unit itself and the battery, antenna

and other options or accessories that make up the

rest of the package to be approved. This approved

package must be strictly observed and there must

be no substitution of items, even if the substitute you

wanted to consider appears as an approved

accessory elsewhere in the Guide for some other

communications equipment unit. Approved

conﬁgurations are listed by FMRC Approved

Product in the annual Approval Guide published by

FMRC. That guide, and the Approval Standard

Class Number 3605 document, can be ordered from

the following address:

Training Resource Center

Publications-Order Processing Dept.

Factory Mutual Engineering and Research

1151 Boston-Providence Turnpike

PO Box 9102

Norwood, MA, 02062

U.S.A.

Telephone: (617) 762-4300

Computer Software Copyright

The products described in this manual may include copyrighted computer

programmes stored in semiconductor memories or other media. Laws in the

United States of America and other countries preserve for Motorola Europe

and Motorola Inc. certain exclusive rights for copyrighted computer

programmes, including the right to copy or reproduce in any form the

copyrighted computer programme. Accordingly, any copyrighted computer

programmes contained in the products described in this manual may not be

copied or reproduced in any manner without the express written permission of

the holders of the rights. Furthermore, the purchase of these products shall

not be deemed to grant either directly or by implication, estoppel, or otherwise,

any licence under the copyrights, patents, or patent applications of the holders

of the rights, except for the normal non-exclusive royalty free licence to use

that arises by operation of the law in the sale of the product.

Intrinsically Safe Radio Information/Computer Software Copyright

2-Year Warranty

PTX600_UserBook Page 14 Thursday, July 3, 1997 9:54 AM

English

LIMITED WARRANTY

MOTOROLA RADIO PRODUCTS

This express limited warranty covers the Product

manufactured by MOTOROLA Radio Products Group and

applies to any warranty already mentioned. MOTOROLA

assumes no obligations or liability for additions or

modifications to this warranty unless specifically made in

writing and signed by an authorised officer of MOTOROLA.

MOTOROLA cannot be responsible in any way for any

ancillary equipment not furnished by MOTOROLA which is

attached to or used in connection with the Product, or for

operation of the Product with any ancillary equipment, and

all such equipment is expressly excluded from this

warranty. Because each system which may use the

Product is unique, MOTOROLA disclaims liability for range,

coverage, or operation of the system as a whole under this

warranty.

This warranty sets forth the full extent of MOTOROLA’S

responsibilities regarding the Product. Repair, replacement

or refund of the purchase price, at MOTOROLA’S option, is

the sole and exclusive remedy of purchaser/user of the

Product. THIS WARRANTY IS GIVEN IN LIEU OF ALL

OTHER EXPRESS WARRANTIES. IMPLIED

WARRANTIES, INCLUDING WITHOUT LIMITATION,

IMPLIED WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, ARE

HEREBY EXCLUDED. IN NO EVENT SHALL

MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF

THE PURCHASE PRICE OF THE PRODUCT, FOR ANY

LOSS OF USE, LOSS OF TIME, INCONVENIENCE,

COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR

OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL

DAMAGES ARISING OUT OF THE USE OR INABILITY

TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH

MAY BE DISCLAIMED BY LAW.

Notwithstanding anything contained herein, MOTOROLA

shall not be liable for any of the following situations:

A)Defects or damage resulting from use of the Product in

other than its normal and customary manner.

B)Defects or damage from misuse, accident, water, liquid

or neglect.

C)Defects or damage from improper or unauthorised

testing, operation, maintenance, service, repair,

installation, alteration, modification, or adjustment.

D)Product which has had the serial number removed or

made illegible.

E)A Product which, due to illegal or unauthorized alteration

of the software/firmware in the Product, does not function

in accordance with Motorola’s published specifications or

the FCC type acceptance labeling in effect for the

Product at the time the Product was initially distributed

from Motorola.

F)Scratches or other cosmetic damage to Product surfaces

that does not affect the operation of the Product.

MOTOROLA shall have no liability whatsoever with respect

to any claim of patent infringement which is based upon the

combination of the Product or parts furnished hereunder

with software, apparatus or devices not furnished by

MOTOROLA, nor will MOTOROLA have any liability

whatsoever for the use of ancillary equipment or software

not furnished by MOTOROLA which is attached to or used

in connection with the Product.

HOW TO GET WARRANTY SERVICE : Provide proof of

purchase and deliver or send the Product item,

transportation and insurance prepaid to an authorized

warranty service location. Warranty service will be provided

by Motorola through one of its authorized warranty service

locations. If you contact the company that sold you the

Product, it can facilitate your obtaining warranty service.

You can also call Motorola for assistance :

65-2812053 (Singapore) or 86-10-68438231 (Beijing).

Limited Warranty

2-Year Warranty

PTX600_UserBook Page 15 Thursday, July 3, 1997 9:54 AM

English

Motorola Malaysia Sdn. Bhd. (Company No. 12631DE),

Bayan Lepas Free Industrial Zone, Phase III,

11900 Penang, Malaysia.

Printed in Malaysia.

PTX600_UserBook Page 16 Thursday, July 3, 1997 9:54 AM

Motorola PTX600 User manual

Brand: Motorola

Model: PTX600

Category: Two-way radios

Type: User manual

Download PDF

report

Motorola PTX600 User manual

Motorola PTX600 User manual

Related papers

Other documents