Whirlpool MEDX700X Product Dimensions

Whirlpool
Brand
Whirlpool
Model
MEDX700X
Category
Electric laundry dryers
Type
Product Dimensions

This manual is also suitable for

Whirlpool MEDX700XW electric dryer offers various features for efficient and convenient laundry care:

  • Its large opening side-swing or wide opening hamper door provides easy access for loading and unloading clothes.
  • Flexible installation options allow for recessed or closet installation with the required minimum spacing provided.
  • The dryer requires a 120/240V electrical supply and a 4" diameter vent for proper operation.
  • A time-delay fuse or circuit breaker is recommended for safe electrical connection, and a separate 30-amp circuit is required.
  • For optimal drying performance, follow the vent system chart provided in the manual, which specifies the maximum exhaust length based on the type and number of vent turns.

Whirlpool MEDX700XW electric dryer offers various features for efficient and convenient laundry care:

  • Its large opening side-swing or wide opening hamper door provides easy access for loading and unloading clothes.
  • Flexible installation options allow for recessed or closet installation with the required minimum spacing provided.
  • The dryer requires a 120/240V electrical supply and a 4" diameter vent for proper operation.
  • A time-delay fuse or circuit breaker is recommended for safe electrical connection, and a separate 30-amp circuit is required.
  • For optimal drying performance, follow the vent system chart provided in the manual, which specifies the maximum exhaust length based on the type and number of vent turns.
27" Wide Electric Dryer
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
MEDX700X
Electrical: This dryer requires a 3 or 4 wire, single
phase, 120/240 volt, 60 Hz., AC only electrical supply
(or 3 or 4 wire, 120/208 volt electrical supply, if speci-
ed on the serial/rating plate) on a separate 30-amp
circuit, fused on both sides of the line. A time-delay
fuse or circuit breaker is recommended. Connect to
an individual branch circuit. Do not have a fuse in the
neutral or grounding circuit.
Exhaust venting: Exhaust your dryer to the outside.
4" (102 mm) diameter vent is required. Rigid or exible
metal exhaust vent must be used. Do not use plastic
or metal foil vet. Exhaust hood must be at least
12" (305 mm) from the ground or any object that
may be in the path of the exhaust.
Hood styles: A & B are recommended.
The vent system chart provides venting requirments
that will help to achieve the best drying performance.
Vent system chart:
NOTE: Side and bottom exhaust installations have
a 90° turn inside the dryer. To determine maximum
exhaust length, add one 90° turn to the chart.
A. Louvered hood
B. Box hood
C. Angled hood (acceptable)
C
Dryer dimensions
Select the route that will provide the straightest and
most direct path outdoors. Plan the installation to
use the fewest number of elbows and turns. Use the
fewest 90° turns possible.
Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.
Ref. W10115226B
01/2011
Do not use vent runs longer than specied in vent
length chart. Determine the number of elbows you
will need.
43"
(1092 mm)
*29
1
/
2
"
(749 mm)
27"
(687 mm)
A
23¾"
(603 mm)
43"
(1092 mm)
27"
(687 mm)
*29
1
/
2
"
(749 mm)
13¾"
(349 mm)
B
A. Large opening side-swing door
B. Wide opening hamper door
A
B
C
18"*
(457 mm)
1"
(25 mm)
27"
(686 mm)
1"
(25 mm)
1"*
(25 mm)
14" max.*
(356 mm)
29
¼"
(743 mm)
5
½"*
(140 mm)
48 in.
(310 cm )
2
*
2
24 in.
(155 cm )
2
*
2
3"*
(76 mm)
3"*
(76 mm)
Minimum required spacing for recessed or closet installation
A. Recessed area
B. Side view - closet or conned area
C. Closet door with vents
*Additional spacing recommended
The dimensions shown following are for the minimum spacing allowed.
Additional spacing should be considered for ease of installation and servicing. ■
Additional clearances might be required for wall, door, and oor moldings. ■
Additional spacing of 1" (25 mm) on all sides of the dryer is recommended to ■
reduce noise transfer.
For closet installation, with a door, minimum ventilation openings in the top and ■
bottom of the door are required.
Louvered doors with equivalent ventilation openings
are acceptable.
Companion appliance spacing should also be considered. ■
The location must be large enough to allow the dryer door to open fully.
Vent System Chart
Number of
90° turns
or elbows
Type
of vent
Box/louvered
hoods
Angled
hoods
1
4
3
2
0
Rigid metal
Rigid metal
Rigid metal
Rigid metal
Rigid metal
64 ft. (20 m)
54 ft. (16.5 m)
44 ft. (13.4 m)
35 ft. (10.7 m)
27 ft. (8.2 m)
58 ft. (17.7 m)
48 ft. (14.6 m)
38 ft. (11.6 m)
29 ft. (8.8 m)
21 ft. (6.4 m)
BA
  • Page 1 1

Whirlpool MEDX700X Product Dimensions

Whirlpool
Brand
Whirlpool
Model
MEDX700X
Category
Electric laundry dryers
Type
Product Dimensions
This manual is also suitable for

Whirlpool MEDX700XW electric dryer offers various features for efficient and convenient laundry care:

  • Its large opening side-swing or wide opening hamper door provides easy access for loading and unloading clothes.
  • Flexible installation options allow for recessed or closet installation with the required minimum spacing provided.
  • The dryer requires a 120/240V electrical supply and a 4" diameter vent for proper operation.
  • A time-delay fuse or circuit breaker is recommended for safe electrical connection, and a separate 30-amp circuit is required.
  • For optimal drying performance, follow the vent system chart provided in the manual, which specifies the maximum exhaust length based on the type and number of vent turns.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents